@@ -542,11 +542,6 @@ The following options need to be configured:
CONF_CM_CACHABLE_CUW
CONF_CM_CACHABLE_ACCELERATED
- CONFIG_SYS_XWAY_EBU_BOOTCFG
-
- Special option for Lantiq XWAY SoCs for booting from NOR flash.
- See also arch/mips/cpu/mips32/start.S.
-
CONFIG_XWAY_SWAP_BYTES
Enable compilation of tools/xway-swap-bytes needed for Lantiq
@@ -390,6 +390,28 @@ config MIPS_CM
wish U-Boot to configure it or make use of it to retrieve system
information such as cache configuration.
+config MIPS_INSERT_BOOT_CONFIG
+ bool
+ default n
+ help
+ Enable this to insert some board-specific boot configuration in
+ the U-Boot binary at offset 0x10.
+
+config MIPS_BOOT_CONFIG_WORD0
+ hex
+ depends on MIPS_INSERT_BOOT_CONFIG
+ default 0x420 if TARGET_MALTA
+ default 0x0
+ help
+ Value which is inserted as boot config word 0.
+
+config MIPS_BOOT_CONFIG_WORD1
+ hex
+ depends on MIPS_INSERT_BOOT_CONFIG
+ default 0x0
+ help
+ Value which is inserted as boot config word 1.
+
endif
endmenu
@@ -84,25 +84,14 @@ ENTRY(_start)
b reset
mtc0 zero, CP0_COUNT # clear cp0 count for most accurate boot timing
-#if defined(CONFIG_SYS_XWAY_EBU_BOOTCFG)
+#if defined(CONFIG_MIPS_INSERT_BOOT_CONFIG)
/*
- * Almost all Lantiq XWAY SoC devices have an external bus unit (EBU) to
- * access external NOR flashes. If the board boots from NOR flash the
- * internal BootROM does a blind read at address 0xB0000010 to read the
- * initial configuration for that EBU in order to access the flash
- * device with correct parameters. This config option is board-specific.
+ * Store some board-specific boot configuration. This is used by some
+ * MIPS systems like Malta.
*/
.org 0x10
- .word CONFIG_SYS_XWAY_EBU_BOOTCFG
- .word 0x0
-#endif
-#if defined(CONFIG_MALTA)
- /*
- * Linux expects the Board ID here.
- */
- .org 0x10
- .word 0x00000420 # 0x420 (Malta Board with CoreLV)
- .word 0x00000000
+ .word CONFIG_MIPS_BOOT_CONFIG_WORD0
+ .word CONFIG_MIPS_BOOT_CONFIG_WORD1
#endif
#if defined(CONFIG_ROM_EXCEPTION_VECTORS)
@@ -4433,7 +4433,6 @@ CONFIG_SYS_XHCI_USB1_ADDR
CONFIG_SYS_XHCI_USB2_ADDR
CONFIG_SYS_XHCI_USB3_ADDR
CONFIG_SYS_XIMG_LEN
-CONFIG_SYS_XWAY_EBU_BOOTCFG
CONFIG_SYS_ZYNQ_QSPI_WAIT
CONFIG_SYS_ZYNQ_SPI_WAIT
CONFIG_SYS_i2C_FSL
Some MIPS systems store some board-specific boot configuration in the U-Boot binary at offset 0x10. This is used by Malta boards and by Lantiq/Intel SoC's when booting from parallel NOR flash. Convert the hard-coded values to Kconfig options to remove such board-specific stuff out of the generic start.S code. This also deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> --- README | 5 ----- arch/mips/Kconfig | 22 ++++++++++++++++++++++ arch/mips/cpu/start.S | 21 +++++---------------- scripts/config_whitelist.txt | 1 - 4 files changed, 27 insertions(+), 22 deletions(-)