| Message ID | 20200728195935.155604-11-saeedm@mellanox.com |
|---|---|
| State | Accepted |
| Delegated to: | David Miller |
| Headers | show |
| Series | [net,V2,01/11] net/mlx5: E-switch, Destroy TSAR when fail to enable the mode | expand |
On Tue, Jul 28, 2020 at 11:07 PM Saeed Mahameed <saeedm@mellanox.com> wrote: > When setting the PF interface up/down, notify the firmware to update > uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled. > This behavior will prevent sending traffic out on uplink port when PF is > down, such as sending traffic from a VF interface which is still up. > Currently when calling mlx5e_open/close(), the driver only sends PAOS > command to notify the firmware to set the physical port state to > up/down, however, it is not sufficient. When VF is in "auto" state, it > follows the uplink state, which was not updated on mlx5e_open/close() > before this patch. > When switchdev mode is enabled and uplink representor is first enabled, > set the uplink port state value back to its FW default "AUTO". So this is not the legacy mode "auto" vf vport state but rather something else? If this is the case what is the semantics of the firmware "auto" state and how it related to the switchdev vport representors architecture/behaviour? > Fixes: 63bfd399de55 ("net/mlx5e: Send PAOS command on interface up/down")
On Wed, 2020-07-29 at 09:17 +0300, Or Gerlitz wrote: > On Tue, Jul 28, 2020 at 11:07 PM Saeed Mahameed <saeedm@mellanox.com> > wrote: > > When setting the PF interface up/down, notify the firmware to > > update > > uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled. > > This behavior will prevent sending traffic out on uplink port when > > PF is > > down, such as sending traffic from a VF interface which is still > > up. > > Currently when calling mlx5e_open/close(), the driver only sends > > PAOS > > command to notify the firmware to set the physical port state to > > up/down, however, it is not sufficient. When VF is in "auto" state, > > it > > follows the uplink state, which was not updated on > > mlx5e_open/close() > > before this patch. > > When switchdev mode is enabled and uplink representor is first > > enabled, > > set the uplink port state value back to its FW default "AUTO". > > So this is not the legacy mode "auto" vf vport state but rather > something else? > Or, this is the uplink esw port and not the PF's, auto means FW/HW manages the state according to the actual physical link state. > If this is the case what is the semantics of the firmware "auto" > state and > how it related to the switchdev vport representors > architecture/behaviour? > No change in the current switchdev behavior, only for legacy and NONE mode. > > > Fixes: 63bfd399de55 ("net/mlx5e: Send PAOS command on interface > > up/down")
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c index 31f9ecae98df9..07fdbea7ea13b 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c @@ -3069,6 +3069,25 @@ void mlx5e_timestamp_init(struct mlx5e_priv *priv) priv->tstamp.rx_filter = HWTSTAMP_FILTER_NONE; } +static void mlx5e_modify_admin_state(struct mlx5_core_dev *mdev, + enum mlx5_port_status state) +{ + struct mlx5_eswitch *esw = mdev->priv.eswitch; + int vport_admin_state; + + mlx5_set_port_admin_status(mdev, state); + + if (!MLX5_ESWITCH_MANAGER(mdev) || mlx5_eswitch_mode(esw) == MLX5_ESWITCH_OFFLOADS) + return; + + if (state == MLX5_PORT_UP) + vport_admin_state = MLX5_VPORT_ADMIN_STATE_AUTO; + else + vport_admin_state = MLX5_VPORT_ADMIN_STATE_DOWN; + + mlx5_eswitch_set_vport_state(esw, MLX5_VPORT_UPLINK, vport_admin_state); +} + int mlx5e_open_locked(struct net_device *netdev) { struct mlx5e_priv *priv = netdev_priv(netdev); @@ -3101,7 +3120,7 @@ int mlx5e_open(struct net_device *netdev) mutex_lock(&priv->state_lock); err = mlx5e_open_locked(netdev); if (!err) - mlx5_set_port_admin_status(priv->mdev, MLX5_PORT_UP); + mlx5e_modify_admin_state(priv->mdev, MLX5_PORT_UP); mutex_unlock(&priv->state_lock); return err; @@ -3135,7 +3154,7 @@ int mlx5e_close(struct net_device *netdev) return -ENODEV; mutex_lock(&priv->state_lock); - mlx5_set_port_admin_status(priv->mdev, MLX5_PORT_DOWN); + mlx5e_modify_admin_state(priv->mdev, MLX5_PORT_DOWN); err = mlx5e_close_locked(netdev); mutex_unlock(&priv->state_lock); @@ -5182,7 +5201,7 @@ static void mlx5e_nic_enable(struct mlx5e_priv *priv) /* Marking the link as currently not needed by the Driver */ if (!netif_running(netdev)) - mlx5_set_port_admin_status(mdev, MLX5_PORT_DOWN); + mlx5e_modify_admin_state(mdev, MLX5_PORT_DOWN); mlx5e_set_netdev_mtu_boundaries(priv); mlx5e_set_dev_port_mtu(priv); diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c index 8c294ab43f908..9519a61bd8ec5 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c @@ -1081,6 +1081,8 @@ static void mlx5e_uplink_rep_enable(struct mlx5e_priv *priv) mlx5e_rep_tc_enable(priv); + mlx5_modify_vport_admin_state(mdev, MLX5_VPORT_STATE_OP_MOD_UPLINK, + 0, 0, MLX5_VPORT_ADMIN_STATE_AUTO); mlx5_lag_add(mdev, netdev); priv->events_nb.notifier_call = uplink_rep_async_event; mlx5_notifier_register(mdev, &priv->events_nb); diff --git a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c index d9376627584e9..71d01143c4556 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c @@ -1826,6 +1826,8 @@ int mlx5_eswitch_set_vport_state(struct mlx5_eswitch *esw, u16 vport, int link_state) { struct mlx5_vport *evport = mlx5_eswitch_get_vport(esw, vport); + int opmod = MLX5_VPORT_STATE_OP_MOD_ESW_VPORT; + int other_vport = 1; int err = 0; if (!ESW_ALLOWED(esw)) @@ -1833,15 +1835,17 @@ int mlx5_eswitch_set_vport_state(struct mlx5_eswitch *esw, if (IS_ERR(evport)) return PTR_ERR(evport); + if (vport == MLX5_VPORT_UPLINK) { + opmod = MLX5_VPORT_STATE_OP_MOD_UPLINK; + other_vport = 0; + vport = 0; + } mutex_lock(&esw->state_lock); - err = mlx5_modify_vport_admin_state(esw->dev, - MLX5_VPORT_STATE_OP_MOD_ESW_VPORT, - vport, 1, link_state); + err = mlx5_modify_vport_admin_state(esw->dev, opmod, vport, other_vport, link_state); if (err) { - mlx5_core_warn(esw->dev, - "Failed to set vport %d link state, err = %d", - vport, err); + mlx5_core_warn(esw->dev, "Failed to set vport %d link state, opmod = %d, err = %d", + vport, opmod, err); goto unlock; } diff --git a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h index a5175e98c0b34..5785596f13f5b 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h +++ b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.h @@ -680,6 +680,8 @@ static inline int mlx5_eswitch_enable(struct mlx5_eswitch *esw, int num_vfs) { r static inline void mlx5_eswitch_disable(struct mlx5_eswitch *esw, bool clear_vf) {} static inline bool mlx5_esw_lag_prereq(struct mlx5_core_dev *dev0, struct mlx5_core_dev *dev1) { return true; } static inline bool mlx5_eswitch_is_funcs_handler(struct mlx5_core_dev *dev) { return false; } +static inline +int mlx5_eswitch_set_vport_state(struct mlx5_eswitch *esw, u16 vport, int link_state) { return 0; } static inline const u32 *mlx5_esw_query_functions(struct mlx5_core_dev *dev) { return ERR_PTR(-EOPNOTSUPP); diff --git a/include/linux/mlx5/mlx5_ifc.h b/include/linux/mlx5/mlx5_ifc.h index 073b79eacc991..1340e02b14ef2 100644 --- a/include/linux/mlx5/mlx5_ifc.h +++ b/include/linux/mlx5/mlx5_ifc.h @@ -4381,6 +4381,7 @@ struct mlx5_ifc_query_vport_state_out_bits { enum { MLX5_VPORT_STATE_OP_MOD_VNIC_VPORT = 0x0, MLX5_VPORT_STATE_OP_MOD_ESW_VPORT = 0x1, + MLX5_VPORT_STATE_OP_MOD_UPLINK = 0x2, }; struct mlx5_ifc_arm_monitor_counter_in_bits {