diff mbox

[U-Boot,8/9] mxs: Fix MMC reset to avoid write errors and timeout in iMX23

Message ID 1358819250-31625-9-git-send-email-otavio@ossystems.com.br
State Not Applicable
Headers show

Commit Message

Otavio Salvador Jan. 22, 2013, 1:47 a.m. UTC 
This does the same reset mask as done in v3.7 Linux kernel code; it
fixed the saveenv command in mx23evk.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
---
 drivers/mmc/mxsmmc.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

Comments

Marek Vasut Jan. 22, 2013, 1:49 a.m. UTC | #1 
Dear Otavio Salvador,

> This does the same reset mask as done in v3.7 Linux kernel code; it
> fixed the saveenv command in mx23evk.
> 
> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
> ---
>  drivers/mmc/mxsmmc.c | 16 +++++++++++-----
>  1 file changed, 11 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/mmc/mxsmmc.c b/drivers/mmc/mxsmmc.c
> index 618659e..0a3f0c4 100644
> --- a/drivers/mmc/mxsmmc.c
> +++ b/drivers/mmc/mxsmmc.c
> @@ -354,11 +354,17 @@ static int mxsmmc_init(struct mmc *mmc)
>  	/* Reset SSP */
>  	mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
> 
> -	/* 8 bits word length in MMC mode */
> -	clrsetbits_le32(&ssp_regs->hw_ssp_ctrl1,
> -		SSP_CTRL1_SSP_MODE_MASK | SSP_CTRL1_WORD_LENGTH_MASK |
> -		SSP_CTRL1_DMA_ENABLE,
> -		SSP_CTRL1_SSP_MODE_SD_MMC | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS);
> +	/* Reset MMC */
> +	writel(SSP_CTRL1_SSP_MODE_SD_MMC |
> +		SSP_CTRL1_WORD_LENGTH_EIGHT_BITS |
> +		SSP_CTRL1_DMA_ENABLE |
> +		SSP_CTRL1_POLARITY |

Will this addition not break mx28?

> +		SSP_CTRL1_RECV_TIMEOUT_IRQ_EN |
> +		SSP_CTRL1_DATA_CRC_IRQ_EN |
> +		SSP_CTRL1_DATA_TIMEOUT_IRQ_EN |
> +		SSP_CTRL1_RESP_TIMEOUT_IRQ_EN |
> +		SSP_CTRL1_RESP_ERR_IRQ_EN,
> +		&ssp_regs->hw_ssp_ctrl1_set);
> 
>  	/* Set initial bit clock 400 KHz */
>  	mxs_set_ssp_busclock(priv->id, 400);

Best regards,
Marek Vasut
Otavio Salvador Jan. 22, 2013, 2:03 a.m. UTC | #2 
On Mon, Jan 21, 2013 at 11:49 PM, Marek Vasut <marex@denx.de> wrote:
> Dear Otavio Salvador,
>
>> This does the same reset mask as done in v3.7 Linux kernel code; it
>> fixed the saveenv command in mx23evk.
>>
>> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
>> ---
>>  drivers/mmc/mxsmmc.c | 16 +++++++++++-----
>>  1 file changed, 11 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/mmc/mxsmmc.c b/drivers/mmc/mxsmmc.c
>> index 618659e..0a3f0c4 100644
>> --- a/drivers/mmc/mxsmmc.c
>> +++ b/drivers/mmc/mxsmmc.c
>> @@ -354,11 +354,17 @@ static int mxsmmc_init(struct mmc *mmc)
>>       /* Reset SSP */
>>       mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
>>
>> -     /* 8 bits word length in MMC mode */
>> -     clrsetbits_le32(&ssp_regs->hw_ssp_ctrl1,
>> -             SSP_CTRL1_SSP_MODE_MASK | SSP_CTRL1_WORD_LENGTH_MASK |
>> -             SSP_CTRL1_DMA_ENABLE,
>> -             SSP_CTRL1_SSP_MODE_SD_MMC | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS);
>> +     /* Reset MMC */
>> +     writel(SSP_CTRL1_SSP_MODE_SD_MMC |
>> +             SSP_CTRL1_WORD_LENGTH_EIGHT_BITS |
>> +             SSP_CTRL1_DMA_ENABLE |
>> +             SSP_CTRL1_POLARITY |
>
> Will this addition not break mx28?

Not tested. I hope it does not as it has been taken from v3.7 kernel.

>> +             SSP_CTRL1_RECV_TIMEOUT_IRQ_EN |
>> +             SSP_CTRL1_DATA_CRC_IRQ_EN |
>> +             SSP_CTRL1_DATA_TIMEOUT_IRQ_EN |
>> +             SSP_CTRL1_RESP_TIMEOUT_IRQ_EN |
>> +             SSP_CTRL1_RESP_ERR_IRQ_EN,
>> +             &ssp_regs->hw_ssp_ctrl1_set);
>>
>>       /* Set initial bit clock 400 KHz */
>>       mxs_set_ssp_busclock(priv->id, 400);
>
> Best regards,
> Marek Vasut



--
Otavio Salvador                             O.S. Systems
E-mail: otavio@ossystems.com.br  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br
Marek Vasut Jan. 22, 2013, 2:15 a.m. UTC | #3 
Dear Otavio Salvador,

> On Mon, Jan 21, 2013 at 11:49 PM, Marek Vasut <marex@denx.de> wrote:
> > Dear Otavio Salvador,
> > 
> >> This does the same reset mask as done in v3.7 Linux kernel code; it
> >> fixed the saveenv command in mx23evk.
> >> 
> >> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
> >> ---
> >> 
> >>  drivers/mmc/mxsmmc.c | 16 +++++++++++-----
> >>  1 file changed, 11 insertions(+), 5 deletions(-)
> >> 
> >> diff --git a/drivers/mmc/mxsmmc.c b/drivers/mmc/mxsmmc.c
> >> index 618659e..0a3f0c4 100644
> >> --- a/drivers/mmc/mxsmmc.c
> >> +++ b/drivers/mmc/mxsmmc.c
> >> @@ -354,11 +354,17 @@ static int mxsmmc_init(struct mmc *mmc)
> >> 
> >>       /* Reset SSP */
> >>       mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
> >> 
> >> -     /* 8 bits word length in MMC mode */
> >> -     clrsetbits_le32(&ssp_regs->hw_ssp_ctrl1,
> >> -             SSP_CTRL1_SSP_MODE_MASK | SSP_CTRL1_WORD_LENGTH_MASK |
> >> -             SSP_CTRL1_DMA_ENABLE,
> >> -             SSP_CTRL1_SSP_MODE_SD_MMC |
> >> SSP_CTRL1_WORD_LENGTH_EIGHT_BITS); +     /* Reset MMC */
> >> +     writel(SSP_CTRL1_SSP_MODE_SD_MMC |
> >> +             SSP_CTRL1_WORD_LENGTH_EIGHT_BITS |
> >> +             SSP_CTRL1_DMA_ENABLE |
> >> +             SSP_CTRL1_POLARITY |
> > 
> > Will this addition not break mx28?
> 
> Not tested. I hope it does not as it has been taken from v3.7 kernel.

Please, mark all such untested code which can possibly break other platforms in 
the description.

Best regards,
Marek Vasut
diff mbox

Patch

diff --git a/drivers/mmc/mxsmmc.c b/drivers/mmc/mxsmmc.c
index 618659e..0a3f0c4 100644
--- a/drivers/mmc/mxsmmc.c
+++ b/drivers/mmc/mxsmmc.c
@@ -354,11 +354,17 @@  static int mxsmmc_init(struct mmc *mmc)
 	/* Reset SSP */
 	mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
 
-	/* 8 bits word length in MMC mode */
-	clrsetbits_le32(&ssp_regs->hw_ssp_ctrl1,
-		SSP_CTRL1_SSP_MODE_MASK | SSP_CTRL1_WORD_LENGTH_MASK |
-		SSP_CTRL1_DMA_ENABLE,
-		SSP_CTRL1_SSP_MODE_SD_MMC | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS);
+	/* Reset MMC */
+	writel(SSP_CTRL1_SSP_MODE_SD_MMC |
+		SSP_CTRL1_WORD_LENGTH_EIGHT_BITS |
+		SSP_CTRL1_DMA_ENABLE |
+		SSP_CTRL1_POLARITY |
+		SSP_CTRL1_RECV_TIMEOUT_IRQ_EN |
+		SSP_CTRL1_DATA_CRC_IRQ_EN |
+		SSP_CTRL1_DATA_TIMEOUT_IRQ_EN |
+		SSP_CTRL1_RESP_TIMEOUT_IRQ_EN |
+		SSP_CTRL1_RESP_ERR_IRQ_EN,
+		&ssp_regs->hw_ssp_ctrl1_set);
 
 	/* Set initial bit clock 400 KHz */
 	mxs_set_ssp_busclock(priv->id, 400);