| Message ID | 20180710214217.1336-4-wsa+renesas@sang-engineering.com |
|---|---|
| State | Accepted |
| Headers | show |
| Series | i2c: recovery: make sure pulses are not misinterpreted | expand |
On 2018-07-10 23:42, Wolfram Sang wrote: > After exiting the while loop, we checked if recovery was successful and > sent a STOP to the clients. Meanwhile however, we send a STOP after > every pulse, so it is not needed after the loop. If we move the check > for a free bus to the end of the while loop, we can shorten and simplify > the logic. It is still ensured that at least one STOP will be sent to > the wire even if SDA was not stuck low. Well, there will be no STOP if ->set_sda isn't implemented, but that case is also handled equivalently after this patch AFAICT, so Reviewed-by: Peter Rosin <peda@axentia.se> > > Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> > --- > drivers/i2c/i2c-core-base.c | 24 ++++++------------------ > 1 file changed, 6 insertions(+), 18 deletions(-) > > diff --git a/drivers/i2c/i2c-core-base.c b/drivers/i2c/i2c-core-base.c > index 871a9731894f..c7995efd58ea 100644 > --- a/drivers/i2c/i2c-core-base.c > +++ b/drivers/i2c/i2c-core-base.c > @@ -191,9 +191,6 @@ int i2c_generic_scl_recovery(struct i2c_adapter *adap) > ret = -EBUSY; > break; > } > - /* Break if SDA is high */ > - if (bri->get_sda && bri->get_sda(adap)) > - break; > } > > val = !val; > @@ -209,22 +206,13 @@ int i2c_generic_scl_recovery(struct i2c_adapter *adap) > if (bri->set_sda) > bri->set_sda(adap, val); > ndelay(RECOVERY_NDELAY / 2); > - } > - > - /* check if recovery actually succeeded */ > - if (bri->get_sda && !bri->get_sda(adap)) > - ret = -EBUSY; > > - /* If all went well, send STOP for a sane bus state. */ > - if (ret == 0 && bri->set_sda) { > - bri->set_scl(adap, 0); > - ndelay(RECOVERY_NDELAY / 2); > - bri->set_sda(adap, 0); > - ndelay(RECOVERY_NDELAY / 2); > - bri->set_scl(adap, 1); > - ndelay(RECOVERY_NDELAY / 2); > - bri->set_sda(adap, 1); > - ndelay(RECOVERY_NDELAY / 2); > + /* Break if SDA is high */ > + if (val && bri->get_sda) { > + ret = bri->get_sda(adap) ? 0 : -EBUSY; > + if (ret == 0) > + break; > + } > } > > if (bri->unprepare_recovery) >
On Tue, Jul 10, 2018 at 11:42:17PM +0200, Wolfram Sang wrote: > After exiting the while loop, we checked if recovery was successful and > sent a STOP to the clients. Meanwhile however, we send a STOP after > every pulse, so it is not needed after the loop. If we move the check > for a free bus to the end of the while loop, we can shorten and simplify > the logic. It is still ensured that at least one STOP will be sent to > the wire even if SDA was not stuck low. > > Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Applied to for-next, thanks!
diff --git a/drivers/i2c/i2c-core-base.c b/drivers/i2c/i2c-core-base.c index 871a9731894f..c7995efd58ea 100644 --- a/drivers/i2c/i2c-core-base.c +++ b/drivers/i2c/i2c-core-base.c @@ -191,9 +191,6 @@ int i2c_generic_scl_recovery(struct i2c_adapter *adap) ret = -EBUSY; break; } - /* Break if SDA is high */ - if (bri->get_sda && bri->get_sda(adap)) - break; } val = !val; @@ -209,22 +206,13 @@ int i2c_generic_scl_recovery(struct i2c_adapter *adap) if (bri->set_sda) bri->set_sda(adap, val); ndelay(RECOVERY_NDELAY / 2); - } - - /* check if recovery actually succeeded */ - if (bri->get_sda && !bri->get_sda(adap)) - ret = -EBUSY; - /* If all went well, send STOP for a sane bus state. */ - if (ret == 0 && bri->set_sda) { - bri->set_scl(adap, 0); - ndelay(RECOVERY_NDELAY / 2); - bri->set_sda(adap, 0); - ndelay(RECOVERY_NDELAY / 2); - bri->set_scl(adap, 1); - ndelay(RECOVERY_NDELAY / 2); - bri->set_sda(adap, 1); - ndelay(RECOVERY_NDELAY / 2); + /* Break if SDA is high */ + if (val && bri->get_sda) { + ret = bri->get_sda(adap) ? 0 : -EBUSY; + if (ret == 0) + break; + } } if (bri->unprepare_recovery)
After exiting the while loop, we checked if recovery was successful and sent a STOP to the clients. Meanwhile however, we send a STOP after every pulse, so it is not needed after the loop. If we move the check for a free bus to the end of the while loop, we can shorten and simplify the logic. It is still ensured that at least one STOP will be sent to the wire even if SDA was not stuck low. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> --- drivers/i2c/i2c-core-base.c | 24 ++++++------------------ 1 file changed, 6 insertions(+), 18 deletions(-)