@@ -1090,6 +1090,10 @@ Peter Meerwald <devel@bct-electronic.com>
bct-brettl2 BF536
+M.Hasewinkel (MHA) <info@ssv-embedded.de>
+
+ dnp5370 BF537
+
#########################################################################
# End of MAINTAINERS list #
#########################################################################
new file mode 100644
@@ -0,0 +1,54 @@
+#
+# U-boot - Makefile
+#
+# Copyright (c) 2005-2007 Analog Device Inc.
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y := $(BOARD).o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
new file mode 100644
@@ -0,0 +1,29 @@
+#
+# Copyright (c) 2005-2008 Analog Device Inc.
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+# This is not actually used for Blackfin boards so do not change it
+#TEXT_BASE = do-not-use-me
+
+CONFIG_BFIN_CPU = bf537-0.3
new file mode 100644
@@ -0,0 +1,104 @@
+/*
+ * U-boot - main board file
+ *
+ * (C) Copyright 2010 3ality Digital Systems
+ *
+ * Copyright (c) 2005-2008 Analog Devices Inc.
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/blackfin.h>
+#include <asm/net.h>
+#include <net.h>
+#include <netdev.h>
+#include <asm/gpio.h>
+
+static void disable_external_watchdog(void)
+{
+#ifdef CONFIG_DNP5370_EXT_WD_DISABLE
+ /* disable external HW watchdog with PH13 = WD1 = 1 */
+ gpio_request(GPIO_PH13, "ext_wd");
+ gpio_direction_output(GPIO_PH13, 1);
+#endif
+}
+
+int checkboard(void)
+{
+ printf("Board: SSV DilNet DNP5370\n");
+ return 0;
+}
+
+#ifdef CONFIG_BFIN_MAC
+static void board_init_enetaddr(uchar *mac_addr)
+{
+#ifdef CONFIG_SYS_NO_FLASH
+# define USE_MAC_IN_FLASH 0
+#else
+# define USE_MAC_IN_FLASH 1
+#endif
+ bool valid_mac = false;
+
+ if (USE_MAC_IN_FLASH) {
+ /* we cram the MAC in the last flash sector */
+ uchar *board_mac_addr = (uchar *)0x202F0000;
+ if (is_valid_ether_addr(board_mac_addr)) {
+ memcpy(mac_addr, board_mac_addr, 6);
+ valid_mac = true;
+ }
+ }
+
+ if (!valid_mac) {
+ puts("Warning: Generating 'random' MAC address\n");
+ bfin_gen_rand_mac(mac_addr);
+ }
+
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return bfin_EMAC_initialize(bis);
+}
+#endif
+
+/* miscellaneous platform dependent initialisations */
+int misc_init_r(void)
+{
+ disable_external_watchdog();
+
+#ifdef CONFIG_BFIN_MAC
+ uchar enetaddr[6];
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr))
+ board_init_enetaddr(enetaddr);
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+ /* we use the last sector for the MAC address / POST LDR */
+ extern flash_info_t flash_info[];
+ flash_protect(FLAG_PROTECT_SET, 0x202F0000, 0x202FFFFF, &flash_info[0]);
+#endif
+
+ return 0;
+}
@@ -186,6 +186,7 @@ cm-bf537e blackfin blackfin
cm-bf537u blackfin blackfin
cm-bf548 blackfin blackfin
cm-bf561 blackfin blackfin
+dnp5370 blackfin blackfin
ibf-dsp561 blackfin blackfin
ip04 blackfin blackfin
tcm-bf518 blackfin blackfin
new file mode 100644
@@ -0,0 +1,67 @@
+This document describes the board support for
+Dil/NetPC DNP/5370 (http://www.dilnetpc.com/dnp0086.htm) module.
+The distributor is SSV (http://www.ssv-embedded.de),
+
+The module used to develop the support files contains:
+
+* Processor: Blackfin BF537 Rev 0.3 (600 MHz core / 120MHz RAM)
+
+* RAM: 32 MB SDRAM
+ Hynix HY57V561620FTP-H 810EA
+ Connected to Blackfin via "Expansion Bus"
+ Address range 0x0000.0000 - 0x1fff.ffff
+
+* NOR flash: 32 MBit (4 MByte)
+ Exel Semiconductor ES29LVS320EB
+ Connected to Blackfin via "Expansion Bus",
+ Chip Selects 0, 1 and 2, each is connected
+ to a 1 MB memory bank at Blackfin, therefore
+ only 3 MB accessible.
+ Address range 0x2000.0000 - 0x202f.ffff
+ CFI compatible
+
+ Exel Semiconductor was bought by Rohm Semiconductor (www.rohm.com).
+
+* NAND flash: 64 MBit (8 MByte)
+ Atmel 45DB642D-CNU
+ Connected to Blackfin via SPI
+ CFI compatible
+
+* Davicom DM9161EP Ethernet PHY
+
+* A SD card reader, connected via SPI
+
+* Hardware watchdog MAX823 or TPS3823
+
+(other devices not listed here)
+
+To run it, the module must be inserted in a 64 pin DIL socket
+on another board, e.g. DNP/EVA13 (together: SSV SK28).
+
+The Blackfin is booted from NOR flash. The NOR flash data begins
+with the U-Boot code and is then followed by the Linux code.
+Finally, the MAC is stored in the last sector.
+You may need to adjust these settings to your needs.
+The memory map used to develop the board support is:
+
+Memory map:
+0x00000000 .. 0x01ffffff SDRAM
+0x20000000 .. 0x202fffff NOR flash
+
+RAM use:
+0x01f9bffc .. 0x01fbbffb U-Boot stack
+0x01f9c000 .. 0x01f9ffff U-Boot global data
+0x01fa0000 .. 0x01fbffff U-Boot malloc() RAM
+0x01fc0000 .. 0x01ffffff U-Boot execution RAM
+
+NOR flash use:
+0x20000000 .. 0x0002ffff U-Boot
+0x20004000 .. 0x20005fff U-Boot environment
+0x20030000 .. 0x202effff Linux kernel image
+0x202f0000 .. 0x202fffff MAC address sector
+
+NOR flash is 0x00300000 (3145728) bytes large (3 MB).
+Max space for compressed kernel in flash is 0x002c0000 (2883584) bytes (2.75 MB)
+Max space for u-boot in flash is 0x00030000 (196608) bytes (192 KB)
+
+The module is hardwired to BYPASS boot mode.
new file mode 100644
@@ -0,0 +1,131 @@
+/*
+ * U-boot - Configuration file for SSV DNP5370 board
+ */
+
+#ifndef __CONFIG_DNP5370_H__
+#define __CONFIG_DNP5370_H__
+
+/* this must come first */
+#include <asm/config-pre.h>
+
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
+
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+#define CONFIG_CLKIN_HZ 25000000
+#define CONFIG_CLKIN_HALF 0
+#define CONFIG_PLL_BYPASS 0
+#define CONFIG_VCO_MULT 24
+#define CONFIG_CCLK_DIV 1
+#define CONFIG_SCLK_DIV 5
+
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_ADD_WDTH 9
+#define CONFIG_MEM_SIZE 32
+
+#define CONFIG_EBIU_SDRRC_VAL 0x03a0
+#define CONFIG_EBIU_SDBCTL_VAL 0x0013
+#define CONFIG_EBIU_SDGCTL_VAL 0x8091998d
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xF7
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
+
+/*
+ * Network Settings
+ */
+#ifndef __ADSPBF534__
+#define CONFIG_IPADDR 10.100.100.21
+#define CONFIG_NETMASK 255.255.0.0
+#define CONFIG_GATEWAYIP 10.100.100.1
+#define CONFIG_SERVERIP 10.100.100.12
+#define CONFIG_ROOTPATH /romfs
+
+#define CONFIG_NET_MULTI 1
+#define CONFIG_BFIN_MAC 1
+#define CONFIG_PHY_ADDR 0
+#define CONFIG_RMII 1
+
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#endif
+
+/*
+ * Flash Settings
+ *
+ * Only 3 MB of the 4 MB NOR flash are addressable.
+ * But limiting the flash size does not seem to work.
+ * It seems the CFI detection has precedence.
+ */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* (M29W320EB) */
+
+/* 512k reserved for u-boot */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 15
+
+/*
+ * Env Storage Settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x20004000
+#define CONFIG_ENV_SIZE 0x00002000
+#define CONFIG_ENV_SECT_SIZE 0x00002000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_OFFSET 0x00004000 /* (CONFIG_ENV_ADDR - CONFIG_FLASH_BASE) */
+
+#define ENV_IS_EMBEDDED
+#define LDS_BOARD_TEXT \
+ arch/blackfin/lib/libblackfin.o (.text*); \
+ arch/blackfin/cpu/libblackfin.o (.text*); \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*);
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_STRINGS
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_SYS_LONGHELP
+
+/* This disables the hardware watchdog (not inside the bfin) */
+#define CONFIG_DNP5370_EXT_WD_DISABLE 1
+
+#define CONFIG_UART_CONSOLE 0
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTCOMMAND "bootm 0x20030000"
+#define CONFIG_BOOTARGS "console=ttyBF0,115200 root=/dev/mtdblock3 rootfstype=ext2"
+
+/* Convenience commands to update Linux in NOR flash */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fetchme=tftpboot 0x01000000 uImage;" \
+ "iminfo\0"\
+ "flashme=protect off 0x20030000 0x2003ffff;" \
+ "erase 0x20030000 0x202effff;" \
+ "cp.b 0x01000000 0x20030000 0x2c0000\0" \
+ "runme=bootm 0x01000000\0"
+
+/* this sets up the default list of enabled commands */
+#include <config_cmd_default.h>
+
+#ifndef CONFIG_BFIN_MAC
+# undef CONFIG_CMD_NET
+# undef CONFIG_CMD_NFS
+#endif
+
+#endif