Message ID | 1426669356-10799-1-git-send-email-zajec5@gmail.com |
---|---|
State | Changes Requested |
Delegated to: | Jonas Gorski |
Headers | show |
On Wed, Mar 18, 2015 at 10:02 AM, Rafał Miłecki <zajec5@gmail.com> wrote: > Signed-off-by: Rafał Miłecki <zajec5@gmail.com> > --- > .../generic/files/drivers/net/phy/b53/b53_common.c | 23 +++++++++++++++++++++- > .../generic/files/drivers/net/phy/b53/b53_regs.h | 1 + > 2 files changed, 23 insertions(+), 1 deletion(-) > > diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c > index e44d194..4597742 100644 > --- a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c > +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c > @@ -525,7 +525,7 @@ static int b53_switch_reset(struct b53_device *dev) > return -EINVAL; > } > } > - } else if ((is531x5(dev) || is5301x(dev)) && dev->sw_dev.cpu_port == B53_CPU_PORT) { > + } else if (is531x5(dev) && dev->sw_dev.cpu_port == B53_CPU_PORT) { > u8 mii_port_override; > > b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > @@ -533,6 +533,27 @@ static int b53_switch_reset(struct b53_device *dev) > b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > mii_port_override | PORT_OVERRIDE_EN | > PORT_OVERRIDE_LINK); > + } else if (is5301x(dev)) { > + /* > + * CPU interface attached to port 8 requires specific handling. > + * It uses different overriding register and extra ports 5 and 7 > + * need to be configured as well. > + */ > + if (dev->sw_dev.cpu_port == 8) { > + u8 mii_port_override; > + > + b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > + &mii_port_override); > + mii_port_override |= PORT_OVERRIDE_LINK | > + PORT_OVERRIDE_RX_FLOW | > + PORT_OVERRIDE_TX_FLOW | > + PORT_OVERRIDE_SPEED_2000M | > + PORT_OVERRIDE_EN; > + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > + mii_port_override); > + } else { > + pr_warn("overriding CPU port other than 8 is not supported yet\n"); > + } > } > > b53_enable_mib(dev); How about @@ -530,9 +530,16 @@ static int b53_switch_reset(struct b53_device *dev) b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, &mii_port_override); + + mii_port_override |= PORT_OVERRIDE_LINK | PORT_OVERRIDE_EN; + + if (is5301x(dev)) + mii_port_override |= PORT_OVERRIDE_RX_FLOW | + PORT_OVERRIDE_TX_FLOW | + PORT_OVERRIDE_SPEED_2000M; + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, - mii_port_override | PORT_OVERRIDE_EN | - PORT_OVERRIDE_LINK); + mii_port_override); } b53_enable_mib(dev); instead of creating a full new branch? Jonas
On 18 March 2015 at 11:28, Jonas Gorski <jogo@openwrt.org> wrote: > On Wed, Mar 18, 2015 at 10:02 AM, Rafał Miłecki <zajec5@gmail.com> wrote: >> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> >> --- >> .../generic/files/drivers/net/phy/b53/b53_common.c | 23 +++++++++++++++++++++- >> .../generic/files/drivers/net/phy/b53/b53_regs.h | 1 + >> 2 files changed, 23 insertions(+), 1 deletion(-) >> >> diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >> index e44d194..4597742 100644 >> --- a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >> +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >> @@ -525,7 +525,7 @@ static int b53_switch_reset(struct b53_device *dev) >> return -EINVAL; >> } >> } >> - } else if ((is531x5(dev) || is5301x(dev)) && dev->sw_dev.cpu_port == B53_CPU_PORT) { >> + } else if (is531x5(dev) && dev->sw_dev.cpu_port == B53_CPU_PORT) { >> u8 mii_port_override; >> >> b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> @@ -533,6 +533,27 @@ static int b53_switch_reset(struct b53_device *dev) >> b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> mii_port_override | PORT_OVERRIDE_EN | >> PORT_OVERRIDE_LINK); >> + } else if (is5301x(dev)) { >> + /* >> + * CPU interface attached to port 8 requires specific handling. >> + * It uses different overriding register and extra ports 5 and 7 >> + * need to be configured as well. >> + */ >> + if (dev->sw_dev.cpu_port == 8) { >> + u8 mii_port_override; >> + >> + b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> + &mii_port_override); >> + mii_port_override |= PORT_OVERRIDE_LINK | >> + PORT_OVERRIDE_RX_FLOW | >> + PORT_OVERRIDE_TX_FLOW | >> + PORT_OVERRIDE_SPEED_2000M | >> + PORT_OVERRIDE_EN; >> + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> + mii_port_override); >> + } else { >> + pr_warn("overriding CPU port other than 8 is not supported yet\n"); >> + } >> } >> >> b53_enable_mib(dev); > > How about > > @@ -530,9 +530,16 @@ static int b53_switch_reset(struct b53_device *dev) > > b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > &mii_port_override); > + > + mii_port_override |= PORT_OVERRIDE_LINK | PORT_OVERRIDE_EN; > + > + if (is5301x(dev)) > + mii_port_override |= PORT_OVERRIDE_RX_FLOW | > + PORT_OVERRIDE_TX_FLOW | > + PORT_OVERRIDE_SPEED_2000M; > + > b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, > - mii_port_override | PORT_OVERRIDE_EN | > - PORT_OVERRIDE_LINK); > + mii_port_override); > } > > b53_enable_mib(dev); > > instead of creating a full new branch? As the comment says, this code for BCM5301X will be extended. This is because of this 2000M speed, which requires configuring 3 ports. It seems communication between switch and CPU interface with such speed couldn't be handled with only a single port. Broadcom decided to use 3 ports in total for that. I don't have that code ready and I also don't like patch bombs, so I started with this simple change. However because of further development plans I vote for a separated branch.
On Wed, Mar 18, 2015 at 12:09 PM, Rafał Miłecki <zajec5@gmail.com> wrote: > On 18 March 2015 at 11:28, Jonas Gorski <jogo@openwrt.org> wrote: >> On Wed, Mar 18, 2015 at 10:02 AM, Rafał Miłecki <zajec5@gmail.com> wrote: >>> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> >>> --- >>> .../generic/files/drivers/net/phy/b53/b53_common.c | 23 +++++++++++++++++++++- >>> .../generic/files/drivers/net/phy/b53/b53_regs.h | 1 + >>> 2 files changed, 23 insertions(+), 1 deletion(-) >>> >>> diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >>> index e44d194..4597742 100644 >>> --- a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >>> +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c >>> @@ -525,7 +525,7 @@ static int b53_switch_reset(struct b53_device *dev) >>> return -EINVAL; >>> } >>> } >>> - } else if ((is531x5(dev) || is5301x(dev)) && dev->sw_dev.cpu_port == B53_CPU_PORT) { >>> + } else if (is531x5(dev) && dev->sw_dev.cpu_port == B53_CPU_PORT) { >>> u8 mii_port_override; >>> >>> b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >>> @@ -533,6 +533,27 @@ static int b53_switch_reset(struct b53_device *dev) >>> b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >>> mii_port_override | PORT_OVERRIDE_EN | >>> PORT_OVERRIDE_LINK); >>> + } else if (is5301x(dev)) { >>> + /* >>> + * CPU interface attached to port 8 requires specific handling. >>> + * It uses different overriding register and extra ports 5 and 7 >>> + * need to be configured as well. >>> + */ >>> + if (dev->sw_dev.cpu_port == 8) { >>> + u8 mii_port_override; >>> + >>> + b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >>> + &mii_port_override); >>> + mii_port_override |= PORT_OVERRIDE_LINK | >>> + PORT_OVERRIDE_RX_FLOW | >>> + PORT_OVERRIDE_TX_FLOW | >>> + PORT_OVERRIDE_SPEED_2000M | >>> + PORT_OVERRIDE_EN; >>> + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >>> + mii_port_override); >>> + } else { >>> + pr_warn("overriding CPU port other than 8 is not supported yet\n"); >>> + } >>> } >>> >>> b53_enable_mib(dev); >> >> How about >> >> @@ -530,9 +530,16 @@ static int b53_switch_reset(struct b53_device *dev) >> >> b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> &mii_port_override); >> + >> + mii_port_override |= PORT_OVERRIDE_LINK | PORT_OVERRIDE_EN; >> + >> + if (is5301x(dev)) >> + mii_port_override |= PORT_OVERRIDE_RX_FLOW | >> + PORT_OVERRIDE_TX_FLOW | >> + PORT_OVERRIDE_SPEED_2000M; >> + >> b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, >> - mii_port_override | PORT_OVERRIDE_EN | >> - PORT_OVERRIDE_LINK); >> + mii_port_override); >> } >> >> b53_enable_mib(dev); >> >> instead of creating a full new branch? > > As the comment says, this code for BCM5301X will be extended. This is > because of this 2000M speed, which requires configuring 3 ports. It > seems communication between switch and CPU interface with such speed > couldn't be handled with only a single port. Broadcom decided to use 3 > ports in total for that. > > I don't have that code ready and I also don't like patch bombs, so I > started with this simple change. However because of further > development plans I vote for a separated branch. Sorry for taking so long to respond, the kernel-size issue on bcm63xx took longer and had more side effects than expected. Then let's keep it simple for now and move it into a separate branch if you actually have the code ready. At least for me, my future code never stays that way how I imagined it will be and it tends to look a lot different when done. Jonas
diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c index e44d194..4597742 100644 --- a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c @@ -525,7 +525,7 @@ static int b53_switch_reset(struct b53_device *dev) return -EINVAL; } } - } else if ((is531x5(dev) || is5301x(dev)) && dev->sw_dev.cpu_port == B53_CPU_PORT) { + } else if (is531x5(dev) && dev->sw_dev.cpu_port == B53_CPU_PORT) { u8 mii_port_override; b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, @@ -533,6 +533,27 @@ static int b53_switch_reset(struct b53_device *dev) b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, mii_port_override | PORT_OVERRIDE_EN | PORT_OVERRIDE_LINK); + } else if (is5301x(dev)) { + /* + * CPU interface attached to port 8 requires specific handling. + * It uses different overriding register and extra ports 5 and 7 + * need to be configured as well. + */ + if (dev->sw_dev.cpu_port == 8) { + u8 mii_port_override; + + b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, + &mii_port_override); + mii_port_override |= PORT_OVERRIDE_LINK | + PORT_OVERRIDE_RX_FLOW | + PORT_OVERRIDE_TX_FLOW | + PORT_OVERRIDE_SPEED_2000M | + PORT_OVERRIDE_EN; + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, + mii_port_override); + } else { + pr_warn("overriding CPU port other than 8 is not supported yet\n"); + } } b53_enable_mib(dev); diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h b/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h index 6d71493..129946d 100644 --- a/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h @@ -86,6 +86,7 @@ #define PORT_OVERRIDE_RV_MII_25 BIT(4) /* BCM5325 only */ #define PORT_OVERRIDE_RX_FLOW BIT(4) #define PORT_OVERRIDE_TX_FLOW BIT(5) +#define PORT_OVERRIDE_SPEED_2000M BIT(6) /* BCM5301X only, requires setting 1000M */ #define PORT_OVERRIDE_EN BIT(7) /* Use the register contents */ /* Power-down mode control */
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> --- .../generic/files/drivers/net/phy/b53/b53_common.c | 23 +++++++++++++++++++++- .../generic/files/drivers/net/phy/b53/b53_regs.h | 1 + 2 files changed, 23 insertions(+), 1 deletion(-)