@@ -18,7 +18,7 @@
/ {
model = "Marvell Armada 3720 Development Board DB-88F3720-DDR3";
- compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3710";
+ compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3700";
chosen {
stdout-path = "serial0:115200n8";
@@ -164,7 +164,7 @@
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins>;
- m25p80@0 {
+ flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <108000000>;
@@ -180,7 +180,7 @@
reg = <0x0 0x200000>;
};
partition@200000 {
- label = "U-Boot Env";
+ label = "U-boot Env";
reg = <0x200000 0x10000>;
};
partition@210000 {
new file mode 100644
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for ESPRESSObin-Ultra board.
+ * Copyright (C) 2019 Globalscale technologies, Inc.
+ *
+ * Jason Hung <jhung@globalscaletechnologies.com>
+ */
+
+/dts-v1/;
+
+#include "armada-3720-espressobin.dtsi"
+
+/ {
+ model = "Globalscale Marvell ESPRESSOBin Ultra Board";
+ compatible = "globalscale,espressobin-ultra", "globalscale,espressobin",
+ "marvell,armada3720", "marvell,armada3700";
+
+ aliases {
+ /* ethernet1 is WAN port */
+ ethernet1 = &switch0port5;
+ ethernet2 = &switch0port1;
+ ethernet3 = &switch0port2;
+ ethernet4 = &switch0port3;
+ ethernet5 = &switch0port4;
+ };
+
+ /delete-node/ regulator;
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpionb 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb3_phy: usb3-phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_vbus>;
+ };
+
+ gpio-leds {
+ pinctrl-names = "default";
+ compatible = "gpio-leds";
+ /* No assigned functions to the LEDs by default */
+ led1 {
+ label = "ebin-ultra:blue:led1";
+ gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+ };
+ led2 {
+ label = "ebin-ultra:green:led2";
+ gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+ };
+ led3 {
+ label = "ebin-ultra:red:led3";
+ gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+ };
+ led4 {
+ label = "ebin-ultra:yellow:led4";
+ gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+};
+
+&sdhci1 {
+ /delete-property/ vqmmc-supply;
+ status = "disabled";
+};
+
+&spi0 {
+ flash@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x3e0000>;
+ };
+ partition@3e0000 {
+ label = "hw-info";
+ reg = <0x3e0000 0x10000>;
+ read-only;
+ };
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x3f0000 0x10000>;
+ };
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <100000>;
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&usb3 {
+ usb-phy = <&usb3_phy>;
+};
+
+&mdio {
+ extphy: ethernet-phy@1 {
+ reg = <1>;
+
+ reset-gpios = <&gpionb 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&switch0 {
+ reg = <3>;
+
+ reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
+
+ ethernet-ports {
+ switch0port1: ethernet-port@1 {
+ reg = <1>;
+ label = "lan0";
+ phy-handle = <&switch0phy0>;
+ };
+
+ switch0port2: ethernet-port@2 {
+ reg = <2>;
+ label = "lan1";
+ phy-handle = <&switch0phy1>;
+ };
+
+ switch0port3: ethernet-port@3 {
+ reg = <3>;
+ label = "lan2";
+ phy-handle = <&switch0phy2>;
+ };
+
+ switch0port4: ethernet-port@4 {
+ reg = <4>;
+ label = "lan3";
+ phy-handle = <&switch0phy3>;
+ };
+
+ switch0port5: ethernet-port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-handle = <&extphy>;
+ phy-mode = "sgmii";
+ };
+ };
+
+ mdio {
+ switch0phy3: ethernet-phy@14 {
+ reg = <0x14>;
+ };
+ };
+};
@@ -16,5 +16,5 @@
/ {
model = "Globalscale Marvell ESPRESSOBin Board";
- compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
+ compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3700";
};
@@ -13,7 +13,7 @@
/ {
aliases {
ethernet0 = ð0;
- /* for dsa slave device */
+ /* for DSA user port device */
ethernet1 = &switch0port1;
ethernet2 = &switch0port2;
ethernet3 = &switch0port3;
@@ -145,19 +145,17 @@
};
&mdio {
- switch0: switch0@1 {
+ switch0: ethernet-switch@1 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
dsa,member = <0 0>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- switch0port0: port@0 {
+ switch0port0: ethernet-port@0 {
reg = <0>;
label = "cpu";
ethernet = <ð0>;
@@ -168,19 +166,19 @@
};
};
- switch0port1: port@1 {
+ switch0port1: ethernet-port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};
- switch0port2: port@2 {
+ switch0port2: ethernet-port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
};
- switch0port3: port@3 {
+ switch0port3: ethernet-port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
@@ -192,13 +190,13 @@
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
};
@@ -14,7 +14,7 @@
/ {
model = "CZ.NIC Turris Mox Board";
compatible = "cznic,turris-mox", "marvell,armada3720",
- "marvell,armada3710";
+ "marvell,armada3700";
aliases {
spi0 = &spi0;
@@ -35,7 +35,7 @@
leds {
compatible = "gpio-leds";
- red {
+ led {
label = "mox:red:activity";
gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-on";
@@ -45,7 +45,7 @@
gpio-keys {
compatible = "gpio-keys";
- reset {
+ key-reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
@@ -100,11 +100,11 @@
sfp: sfp {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
- los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
- rate-select0-gpio = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
+ rate-select0-gpios = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
/* enabled by U-Boot if SFP module is present */
@@ -125,9 +125,12 @@
/delete-property/ mrvl,i2c-fast-mode;
status = "okay";
+ /* MCP7940MT-I/MNY RTC */
rtc@6f {
compatible = "microchip,mcp7940x";
reg = <0x6f>;
+ interrupt-parent = <&gpiosb>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO2_5 */
};
};
@@ -136,6 +139,7 @@
pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
status = "okay";
reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ slot-power-limit-milliwatt = <10000>;
/*
* U-Boot port for Turris Mox has a bug which always expects that "ranges" DT property
* contains exactly 2 ranges with 3 (child) address cells, 2 (parent) address cells and
@@ -144,7 +148,7 @@
* no remapping) and that this address is the lowest from all specified ranges. If these
* conditions are not met then U-Boot crashes during loading kernel DTB file. PCIe address
* space is 128 MB long, so the best split between MEM and IO is to use fixed 16 MB window
- * for IO and the rest 112 MB (64+32+16) for MEM. Controller supports 32-bit IO mapping.
+ * for IO and the rest 112 MB (64+32+16) for MEM, despite that maximal IO size is just 64 kB.
* This bug is not present in U-Boot ports for other Armada 3700 devices and is fixed in
* U-Boot version 2021.07. See relevant U-Boot commits (the last one contains fix):
* https://source.denx.de/u-boot/u-boot/-/commit/cb2ddb291ee6fcbddd6d8f4ff49089dfe580f5d7
@@ -211,7 +215,7 @@
assigned-clock-parents = <&tbg 1>;
assigned-clock-rates = <20000000>;
- spi-flash@0 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
@@ -300,10 +304,16 @@
reg = <1>;
};
- /* switch nodes are enabled by U-Boot if modules are present */
+ /*
+ * NOTE: switch nodes are enabled by U-Boot if modules are present
+ * DO NOT change this node name (switch0@10) even if it is not following
+ * conventions! Deployed U-Boot binaries are explicitly looking for
+ * this node in order to augment the device tree!
+ * Also do not touch the "ports" or "port@n" nodes. These are also ABI.
+ */
switch0@10 {
- compatible = "marvell,mv88e6190";
- reg = <0x10 0>;
+ compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190";
+ reg = <0x10>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(0)>;
@@ -313,35 +323,35 @@
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
@@ -426,9 +436,10 @@
};
};
+ /* NOTE: this node name is ABI, don't change it! */
switch0@2 {
- compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085";
+ reg = <0x2>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
@@ -438,19 +449,19 @@
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1_topaz: switch0phy1@11 {
+ switch0phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy2_topaz: switch0phy2@12 {
+ switch0phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy3_topaz: switch0phy3@13 {
+ switch0phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch0phy4_topaz: switch0phy4@14 {
+ switch0phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
@@ -493,9 +504,10 @@
};
};
+ /* NOTE: this node name is ABI, don't change it! */
switch1@11 {
- compatible = "marvell,mv88e6190";
- reg = <0x11 0>;
+ compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190";
+ reg = <0x11>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(1)>;
@@ -505,35 +517,35 @@
#address-cells = <1>;
#size-cells = <0>;
- switch1phy1: switch1phy1@1 {
+ switch1phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch1phy2: switch1phy2@2 {
+ switch1phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch1phy3: switch1phy3@3 {
+ switch1phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch1phy4: switch1phy4@4 {
+ switch1phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch1phy5: switch1phy5@5 {
+ switch1phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch1phy6: switch1phy6@6 {
+ switch1phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch1phy7: switch1phy7@7 {
+ switch1phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch1phy8: switch1phy8@8 {
+ switch1phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
@@ -618,9 +630,10 @@
};
};
+ /* NOTE: this node name is ABI, don't change it! */
switch1@2 {
- compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085";
+ reg = <0x2>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
@@ -630,19 +643,19 @@
#address-cells = <1>;
#size-cells = <0>;
- switch1phy1_topaz: switch1phy1@11 {
+ switch1phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch1phy2_topaz: switch1phy2@12 {
+ switch1phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch1phy3_topaz: switch1phy3@13 {
+ switch1phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch1phy4_topaz: switch1phy4@14 {
+ switch1phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
@@ -685,9 +698,10 @@
};
};
+ /* NOTE: this node name is ABI, don't change it! */
switch2@12 {
- compatible = "marvell,mv88e6190";
- reg = <0x12 0>;
+ compatible = "marvell,turris-mox-mv88e6190", "marvell,mv88e6190";
+ reg = <0x12>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(2)>;
@@ -697,35 +711,35 @@
#address-cells = <1>;
#size-cells = <0>;
- switch2phy1: switch2phy1@1 {
+ switch2phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch2phy2: switch2phy2@2 {
+ switch2phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch2phy3: switch2phy3@3 {
+ switch2phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch2phy4: switch2phy4@4 {
+ switch2phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch2phy5: switch2phy5@5 {
+ switch2phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch2phy6: switch2phy6@6 {
+ switch2phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch2phy7: switch2phy7@7 {
+ switch2phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch2phy8: switch2phy8@8 {
+ switch2phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
@@ -801,9 +815,10 @@
};
};
+ /* NOTE: this node name is ABI, don't change it! */
switch2@2 {
- compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ compatible = "marvell,turris-mox-mv88e6085", "marvell,mv88e6085";
+ reg = <0x2>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
@@ -813,19 +828,19 @@
#address-cells = <1>;
#size-cells = <0>;
- switch2phy1_topaz: switch2phy1@11 {
+ switch2phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch2phy2_topaz: switch2phy2@12 {
+ switch2phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch2phy3_topaz: switch2phy3@13 {
+ switch2phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch2phy4_topaz: switch2phy4@14 {
+ switch2phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
@@ -11,10 +11,10 @@
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
- los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
};
@@ -61,10 +61,10 @@
sfp_eth1: sfp-eth1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
- los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
};
@@ -13,7 +13,7 @@
/ {
model = "Marvell Armada 3720 SoC";
- compatible = "marvell,armada3720", "marvell,armada3710";
+ compatible = "marvell,armada3720", "marvell,armada3700";
cpus {
cpu1: cpu@1 {
@@ -35,6 +35,11 @@
reg = <0 0x4000000 0 0x200000>;
no-map;
};
+
+ tee@4400000 {
+ reg = <0 0x4400000 0 0x1000000>;
+ no-map;
+ };
};
cpus {
@@ -132,10 +137,20 @@
reg = <0x11500 0x40>;
};
+ uartclk: clock-controller@12010 {
+ compatible = "marvell,armada-3700-uart-clock";
+ reg = <0x12010 0x4>, <0x12210 0x4>;
+ clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>,
+ <&tbg 3>, <&xtalclk>;
+ clock-names = "TBG-A-P", "TBG-B-P", "TBG-A-S",
+ "TBG-B-S", "xtal";
+ #clock-cells = <1>;
+ };
+
uart0: serial@12000 {
compatible = "marvell,armada-3700-uart";
reg = <0x12000 0x18>;
- clocks = <&xtalclk>;
+ clocks = <&uartclk 0>;
interrupts =
<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
@@ -147,7 +162,7 @@
uart1: serial@12200 {
compatible = "marvell,armada-3700-uart-ext";
reg = <0x12200 0x30>;
- clocks = <&xtalclk>;
+ clocks = <&uartclk 1>;
interrupts =
<GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>;
@@ -434,7 +449,7 @@
#mbox-cells = <1>;
};
- sdhci1: sdhci@d0000 {
+ sdhci1: mmc@d0000 {
compatible = "marvell,armada-3700-sdhci",
"marvell,sdhci-xenon";
reg = <0xd0000 0x300>,
@@ -445,7 +460,7 @@
status = "disabled";
};
- sdhci0: sdhci@d8000 {
+ sdhci0: mmc@d8000 {
compatible = "marvell,armada-3700-sdhci",
"marvell,sdhci-xenon";
reg = <0xd8000 0x300>,
@@ -489,6 +504,7 @@
bus-range = <0x00 0xff>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
#interrupt-cells = <1>;
+ clocks = <&sb_periph_clk 13>;
msi-parent = <&pcie0>;
msi-controller;
/*
Update existing armada-37xx DTS files with those in linux v6.8 and add devicetree for ESPRESSObin Ultra device. Signed-off-by: Benjamin Schneider <ben@bens.haus> --- Changes in v2: - upstream is missing a patch for PCIe mem arch/arm/dts/armada-3720-db.dts | 6 +- .../arm/dts/armada-3720-espressobin-ultra.dts | 167 ++++++++++++++++++ arch/arm/dts/armada-3720-espressobin.dts | 2 +- arch/arm/dts/armada-3720-espressobin.dtsi | 22 ++- arch/arm/dts/armada-3720-turris-mox.dts | 133 +++++++------- arch/arm/dts/armada-3720-uDPU.dts | 8 +- arch/arm/dts/armada-3720-uDPU.dtsi | 8 +- arch/arm/dts/armada-372x.dtsi | 2 +- arch/arm/dts/armada-37xx.dtsi | 24 ++- 9 files changed, 284 insertions(+), 88 deletions(-) create mode 100644 arch/arm/dts/armada-3720-espressobin-ultra.dts