[v6,2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support

The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
form factor.

Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
---
v6:
 - increase PHY_ANEG_TIMEOUT
 - spl: print boot source on startup
 - spl: remove PMIC output
 - enable CONFIG_CMD_TIME

v5:
 - save env in eMMC boot partition 0

v4: update board integration

 - migrate to IMX_CONFIG
 - convert config options to Kconfig
  - CONFIG_POWER_I2C
  - CONFIG_SPL_POWER_I2C
  - CONFIG_POWER_LEGACY
  - CONFIG_SYS_LOAD_ADDR
  - CONFIG_SYS_I2C_MXC
  - CONFIG_SYS_I2C_LEGACY
  - CONFIG_SYS_I2C_MXC_I2C1
  - CONFIG_SYS_I2C_MXC_I2C2
  - CONFIG_SYS_I2C_MXC_I2C3
  - CONFIG_SYS_LOAD_ADDR
  - CONFIG_MXC_GPIO

v3:
 - enable EFI capsule support
 - add update FIT image creation to binman config
 - change env offset to fit into eMMC boot partition

v2:
 - add support for 2/4GB variant
 - enable config options
  - CONFIG_CMD_GPT
  - CONFIG_DM_ETH_PHY
  - CONFIG_EFI_SET_TIME
 - add pxefile_addr_r env variable


 .../dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi |  163 ++
 arch/arm/mach-imx/imx8m/Kconfig               |    7 +
 board/kontron/pitx_imx8m/Kconfig              |   15 +
 board/kontron/pitx_imx8m/MAINTAINERS          |    7 +
 board/kontron/pitx_imx8m/Makefile             |    8 +
 board/kontron/pitx_imx8m/imximage.cfg         |    5 +
 board/kontron/pitx_imx8m/lpddr4_timing_2gb.c  | 1853 +++++++++++++++++
 board/kontron/pitx_imx8m/lpddr4_timing_4gb.c  | 1853 +++++++++++++++++
 board/kontron/pitx_imx8m/pitx_imx8m.c         |  156 ++
 board/kontron/pitx_imx8m/spl.c                |  327 +++
 configs/kontron_pitx_imx8m_defconfig          |   87 +
 doc/board/kontron/index.rst                   |    1 +
 doc/board/kontron/pitx-imx8m.rst              |   67 +
 include/configs/kontron_pitx_imx8m.h          |  111 +
 14 files changed, 4660 insertions(+)
 create mode 100644 arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi
 create mode 100644 board/kontron/pitx_imx8m/Kconfig
 create mode 100644 board/kontron/pitx_imx8m/MAINTAINERS
 create mode 100644 board/kontron/pitx_imx8m/Makefile
 create mode 100644 board/kontron/pitx_imx8m/imximage.cfg
 create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_2gb.c
 create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_4gb.c
 create mode 100644 board/kontron/pitx_imx8m/pitx_imx8m.c
 create mode 100644 board/kontron/pitx_imx8m/spl.c
 create mode 100644 configs/kontron_pitx_imx8m_defconfig
 create mode 100644 doc/board/kontron/pitx-imx8m.rst
 create mode 100644 include/configs/kontron_pitx_imx8m.h

Hi Heiko,

On 14.10.21 20:08, Heiko Thiery wrote:
> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> form factor.
> 

There is still something using binman that does not work with CI. 
Without CI, we load all firmware including signed_hdmi_imx8m.bin.

But on CI, file is not loaded, but instead of warnings, build for this 
board fails with :

+Image 'main-section' is missing external blobs and is non-functional: 
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n 
spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000 
./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such 
file or directory
+

Could you take a look ?

Best regards,
Stefano Babic

> Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
> ---
> v6:
>   - increase PHY_ANEG_TIMEOUT
>   - spl: print boot source on startup
>   - spl: remove PMIC output
>   - enable CONFIG_CMD_TIME
> 
> v5:
>   - save env in eMMC boot partition 0
> 
> v4: update board integration
> 
>   - migrate to IMX_CONFIG
>   - convert config options to Kconfig
>    - CONFIG_POWER_I2C
>    - CONFIG_SPL_POWER_I2C
>    - CONFIG_POWER_LEGACY
>    - CONFIG_SYS_LOAD_ADDR
>    - CONFIG_SYS_I2C_MXC
>    - CONFIG_SYS_I2C_LEGACY
>    - CONFIG_SYS_I2C_MXC_I2C1
>    - CONFIG_SYS_I2C_MXC_I2C2
>    - CONFIG_SYS_I2C_MXC_I2C3
>    - CONFIG_SYS_LOAD_ADDR
>    - CONFIG_MXC_GPIO
> 
> v3:
>   - enable EFI capsule support
>   - add update FIT image creation to binman config
>   - change env offset to fit into eMMC boot partition
> 
> v2:
>   - add support for 2/4GB variant
>   - enable config options
>    - CONFIG_CMD_GPT
>    - CONFIG_DM_ETH_PHY
>    - CONFIG_EFI_SET_TIME
>   - add pxefile_addr_r env variable
> 
> 
>   .../dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi |  163 ++
>   arch/arm/mach-imx/imx8m/Kconfig               |    7 +
>   board/kontron/pitx_imx8m/Kconfig              |   15 +
>   board/kontron/pitx_imx8m/MAINTAINERS          |    7 +
>   board/kontron/pitx_imx8m/Makefile             |    8 +
>   board/kontron/pitx_imx8m/imximage.cfg         |    5 +
>   board/kontron/pitx_imx8m/lpddr4_timing_2gb.c  | 1853 +++++++++++++++++
>   board/kontron/pitx_imx8m/lpddr4_timing_4gb.c  | 1853 +++++++++++++++++
>   board/kontron/pitx_imx8m/pitx_imx8m.c         |  156 ++
>   board/kontron/pitx_imx8m/spl.c                |  327 +++
>   configs/kontron_pitx_imx8m_defconfig          |   87 +
>   doc/board/kontron/index.rst                   |    1 +
>   doc/board/kontron/pitx-imx8m.rst              |   67 +
>   include/configs/kontron_pitx_imx8m.h          |  111 +
>   14 files changed, 4660 insertions(+)
>   create mode 100644 arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi
>   create mode 100644 board/kontron/pitx_imx8m/Kconfig
>   create mode 100644 board/kontron/pitx_imx8m/MAINTAINERS
>   create mode 100644 board/kontron/pitx_imx8m/Makefile
>   create mode 100644 board/kontron/pitx_imx8m/imximage.cfg
>   create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_2gb.c
>   create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_4gb.c
>   create mode 100644 board/kontron/pitx_imx8m/pitx_imx8m.c
>   create mode 100644 board/kontron/pitx_imx8m/spl.c
>   create mode 100644 configs/kontron_pitx_imx8m_defconfig
>   create mode 100644 doc/board/kontron/pitx-imx8m.rst
>   create mode 100644 include/configs/kontron_pitx_imx8m.h
> 
> diff --git a/arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi b/arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi
> new file mode 100644
> index 0000000000..cf649b0314
> --- /dev/null
> +++ b/arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi
> @@ -0,0 +1,163 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +
> +#include <config.h>
> +
> +/ {
> +	binman: binman {
> +		multiple-images;
> +	};
> +};
> +
> +&binman {
> +	u-boot-spl-ddr {
> +		filename = "u-boot-spl-ddr.bin";
> +		pad-byte = <0xff>;
> +		align-size = <4>;
> +		align = <4>;
> +
> +		u-boot-spl {
> +			align-end = <4>;
> +		};
> +
> +		blob_1: blob-ext@1 {
> +			filename = "lpddr4_pmu_train_1d_imem.bin";
> +			size = <0x8000>;
> +		};
> +
> +		blob_2: blob-ext@2 {
> +			filename = "lpddr4_pmu_train_1d_dmem.bin";
> +			size = <0x4000>;
> +		};
> +
> +		blob_3: blob-ext@3 {
> +			filename = "lpddr4_pmu_train_2d_imem.bin";
> +			size = <0x8000>;
> +		};
> +
> +		blob_4: blob-ext@4 {
> +			filename = "lpddr4_pmu_train_2d_dmem.bin";
> +			size = <0x4000>;
> +		};
> +	};
> +
> +	spl {
> +		filename = "spl.bin";
> +
> +		mkimage {
> +			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";
> +
> +			blob {
> +				filename = "u-boot-spl-ddr.bin";
> +			};
> +		};
> +	};
> +
> +	itb {
> +		filename = "u-boot.itb";
> +
> +		fit {
> +			description = "Configuration to load ATF before U-Boot";
> +			#address-cells = <1>;
> +			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
> +
> +			images {
> +				uboot {
> +					description = "U-Boot (64-bit)";
> +					type = "standalone";
> +					arch = "arm64";
> +					compression = "none";
> +					load = <CONFIG_SYS_TEXT_BASE>;
> +
> +					u-boot-nodtb {
> +					};
> +				};
> +
> +				atf {
> +					description = "ARM Trusted Firmware";
> +					type = "firmware";
> +					arch = "arm64";
> +					compression = "none";
> +					load = <0x910000>;
> +					entry = <0x910000>;
> +
> +					atf_blob: blob-ext {
> +						filename = "bl31.bin";
> +					};
> +				};
> +
> +				fdt {
> +					description = "imx8mq-kontron-pitx-imx8m.dtb";
> +					type = "flat_dt";
> +					compression = "none";
> +
> +					uboot_fdt_blob: blob-ext {
> +						filename = "u-boot.dtb";
> +					};
> +				};
> +			};
> +
> +			configurations {
> +				default = "conf";
> +
> +				conf {
> +					description = "imx8mq-kontron-pitx-imx8m.dtb";
> +					firmware = "uboot";
> +					loadables = "atf";
> +					fdt = "fdt";
> +				};
> +			};
> +		};
> +	};
> +
> +	imx-boot {
> +		filename = "flash.bin";
> +		pad-byte = <0x00>;
> +
> +		spl: blob-ext@1 {
> +			offset = <0x0>;
> +			filename = "spl.bin";
> +		};
> +
> +		uboot: blob-ext@2 {
> +			offset = <0x57c00>;
> +			filename = "u-boot.itb";
> +		};
> +	};
> +
> +	u-boot-update {
> +		filename = "firmware-update.itb";
> +
> +		fit {
> +			description = "Configuration for firmware update file";
> +
> +			images {
> +				flash-bin {
> +					description = "U-Boot flash image";
> +					type = "firmware";
> +					os = "u-boot";
> +					arch = "arm";
> +					compress = "none";
> +					load = <0>; /* unused */
> +
> +					blob {
> +						filename = "flash.bin";
> +					};
> +
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&reg_usdhc2_vmmc {
> +	off-on-delay-us = <0>;
> +};
> +
> +&usdhc1 {
> +	mmc-hs400-1_8v;
> +};
> +
> +&usdhc2 {
> +	sd-uhs-sdr104;
> +	sd-uhs-ddr50;
> +};
> diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
> index ccaf106be5..86279dba93 100644
> --- a/arch/arm/mach-imx/imx8m/Kconfig
> +++ b/arch/arm/mach-imx/imx8m/Kconfig
> @@ -101,6 +101,12 @@ config TARGET_PICO_IMX8MQ
>   	select IMX8MQ
>   	select IMX8M_LPDDR4
>   
> +config TARGET_KONTRON_PITX_IMX8M
> +	bool "Support Kontron pITX-imx8m"
> +	select BINMAN
> +	select IMX8MQ
> +	select IMX8M_LPDDR4
> +
>   config TARGET_VERDIN_IMX8MM
>          bool "Support Toradex Verdin iMX8M Mini module"
>          select IMX8MM
> @@ -150,6 +156,7 @@ source "board/freescale/imx8mn_evk/Kconfig"
>   source "board/freescale/imx8mp_evk/Kconfig"
>   source "board/gateworks/venice/Kconfig"
>   source "board/google/imx8mq_phanbell/Kconfig"
> +source "board/kontron/pitx_imx8m/Kconfig"
>   source "board/phytec/phycore_imx8mm/Kconfig"
>   source "board/phytec/phycore_imx8mp/Kconfig"
>   source "board/ronetix/imx8mq-cm/Kconfig"
> diff --git a/board/kontron/pitx_imx8m/Kconfig b/board/kontron/pitx_imx8m/Kconfig
> new file mode 100644
> index 0000000000..5dce2cd37e
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_KONTRON_PITX_IMX8M
> +
> +config SYS_BOARD
> +	default "pitx_imx8m"
> +
> +config SYS_VENDOR
> +	default "kontron"
> +
> +config SYS_CONFIG_NAME
> +	default "kontron_pitx_imx8m"
> +
> +config IMX_CONFIG
> +	default "board/kontron/pitx_imx8m/imximage.cfg"
> +
> +endif
> diff --git a/board/kontron/pitx_imx8m/MAINTAINERS b/board/kontron/pitx_imx8m/MAINTAINERS
> new file mode 100644
> index 0000000000..aad84528e3
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/MAINTAINERS
> @@ -0,0 +1,7 @@
> +Kontron pITX-imx8m Board
> +M:	Heiko Thiery <heiko.thiery@gmail.com>
> +S:	Maintained
> +F:	arch/arm/dts/imx8mq-kontron-pitx-imx8m*
> +F:	board/kontron/pitx_imx8m/*
> +F:	include/configs/kontron_pitx_imx8m.h
> +F:	configs/kontron_pitx_imx8m_defconfig
> diff --git a/board/kontron/pitx_imx8m/Makefile b/board/kontron/pitx_imx8m/Makefile
> new file mode 100644
> index 0000000000..904c480281
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/Makefile
> @@ -0,0 +1,8 @@
> +# SPDX-License-Identifier:      GPL-2.0+
> +
> +obj-y += pitx_imx8m.o
> +
> +ifdef CONFIG_SPL_BUILD
> +obj-y += spl.o
> +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing_2gb.o lpddr4_timing_4gb.o
> +endif
> diff --git a/board/kontron/pitx_imx8m/imximage.cfg b/board/kontron/pitx_imx8m/imximage.cfg
> new file mode 100644
> index 0000000000..4a110c8bcc
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/imximage.cfg
> @@ -0,0 +1,5 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +
> +BOOT_FROM	sd
> +SIGNED_HDMI	signed_hdmi_imx8m.bin
> +LOADER		u-boot-spl-ddr.bin	0x7E1000
> diff --git a/board/kontron/pitx_imx8m/lpddr4_timing_2gb.c b/board/kontron/pitx_imx8m/lpddr4_timing_2gb.c
> new file mode 100644
> index 0000000000..b4647b9847
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/lpddr4_timing_2gb.c
> @@ -0,0 +1,1853 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <linux/kernel.h>
> +#include <asm/arch/ddr.h>
> +#include <asm/arch/lpddr4_define.h>
> +
> +static struct dram_cfg_param ddr_ddrc_cfg[] = {
> +	/** Initialize DDRC registers **/
> +	{ 0x3d400304, 0x1 },
> +	{ 0x3d400030, 0x1 },
> +	{ 0x3d400000, 0xa1080020 },
> +	{ 0x3d400028, 0x0 },
> +	{ 0x3d400020, 0x202 },
> +	{ 0x3d400024, 0x3e800 },
> +	{ 0x3d400064, 0x1800e0 },
> +	{ 0x3d4000d0, 0xc003061c },
> +	{ 0x3d4000d4, 0x9e0000 },
> +	{ 0x3d4000dc, 0xd4002d },
> +	{ 0x3d4000e0, 0x310008 },
> +	{ 0x3d4000e8, 0x66004a },
> +	{ 0x3d4000ec, 0x16004a },
> +	{ 0x3d400100, 0x1a200624 },
> +	{ 0x3d400104, 0x60636 },
> +	{ 0x3d40010c, 0xc0c000 },
> +	{ 0x3d400110, 0x10040a10 },
> +	{ 0x3d400114, 0x2040c0c },
> +	{ 0x3d400118, 0x1010007 },
> +	{ 0x3d40011c, 0x401 },
> +	{ 0x3d400130, 0x20600 },
> +	{ 0x3d400134, 0xc100002 },
> +	{ 0x3d400138, 0xe6 },
> +	{ 0x3d400144, 0xa00050 },
> +	{ 0x3d400180, 0xc3200018 },
> +	{ 0x3d400184, 0x28061a8 },
> +	{ 0x3d400188, 0x0 },
> +	{ 0x3d400190, 0x497820a },
> +	{ 0x3d400194, 0x80303 },
> +	{ 0x3d4001a0, 0xe0400018 },
> +	{ 0x3d4001a4, 0xdf00e4 },
> +	{ 0x3d4001a8, 0x80000000 },
> +	{ 0x3d4001b0, 0x11 },
> +	{ 0x3d4001b4, 0x170a },
> +	{ 0x3d4001c0, 0x1 },
> +	{ 0x3d4001c4, 0x1 },
> +	{ 0x3d4000f4, 0x639 },
> +	{ 0x3d400108, 0x70e1617 },
> +	{ 0x3d400200, 0x1f },
> +	{ 0x3d40020c, 0x0 },
> +	{ 0x3d400210, 0x1f1f },
> +	{ 0x3d400204, 0x80808 },
> +	{ 0x3d400214, 0x7070707 },
> +	{ 0x3d400218, 0x7070707 },
> +	{ 0x3d402020, 0x0 },
> +	{ 0x3d402024, 0x7d00 },
> +	{ 0x3d402050, 0x20d040 },
> +	{ 0x3d402064, 0x3001c },
> +	{ 0x3d4020dc, 0x840000 },
> +	{ 0x3d4020e0, 0x310000 },
> +	{ 0x3d4020e8, 0x66004a },
> +	{ 0x3d4020ec, 0x16004a },
> +	{ 0x3d402100, 0xa040005 },
> +	{ 0x3d402104, 0x30407 },
> +	{ 0x3d402108, 0x203060b },
> +	{ 0x3d40210c, 0x505000 },
> +	{ 0x3d402110, 0x2040202 },
> +	{ 0x3d402114, 0x2030202 },
> +	{ 0x3d402118, 0x1010004 },
> +	{ 0x3d40211c, 0x301 },
> +	{ 0x3d402130, 0x20300 },
> +	{ 0x3d402134, 0xa100002 },
> +	{ 0x3d402138, 0x1d },
> +	{ 0x3d402144, 0x14000a },
> +	{ 0x3d402180, 0xc0640004 },
> +	{ 0x3d402190, 0x3818200 },
> +	{ 0x3d402194, 0x80303 },
> +	{ 0x3d4021b4, 0x100 },
> +	{ 0x3d403020, 0x0 },
> +	{ 0x3d403024, 0x1f40 },
> +	{ 0x3d403050, 0x20d040 },
> +	{ 0x3d403064, 0x30007 },
> +	{ 0x3d4030dc, 0x840000 },
> +	{ 0x3d4030e0, 0x310000 },
> +	{ 0x3d4030e8, 0x66004a },
> +	{ 0x3d4030ec, 0x16004a },
> +	{ 0x3d403100, 0xa010102 },
> +	{ 0x3d403104, 0x30404 },
> +	{ 0x3d403108, 0x203060b },
> +	{ 0x3d40310c, 0x505000 },
> +	{ 0x3d403110, 0x2040202 },
> +	{ 0x3d403114, 0x2030202 },
> +	{ 0x3d403118, 0x1010004 },
> +	{ 0x3d40311c, 0x301 },
> +	{ 0x3d403130, 0x20300 },
> +	{ 0x3d403134, 0xa100002 },
> +	{ 0x3d403138, 0x8 },
> +	{ 0x3d403144, 0x50003 },
> +	{ 0x3d403180, 0xc0190004 },
> +	{ 0x3d403190, 0x3818200 },
> +	{ 0x3d403194, 0x80303 },
> +	{ 0x3d4031b4, 0x100 },
> +	{ 0x3d400244, 0x0 },
> +	{ 0x3d400250, 0x29001505 },
> +	{ 0x3d400254, 0x2c },
> +	{ 0x3d40025c, 0x5900575b },
> +	{ 0x3d400264, 0x90000096 },
> +	{ 0x3d40026c, 0x1000012c },
> +	{ 0x3d400300, 0x16 },
> +	{ 0x3d400304, 0x0 },
> +	{ 0x3d40030c, 0x0 },
> +	{ 0x3d400320, 0x1 },
> +	{ 0x3d40036c, 0x11 },
> +	{ 0x3d400400, 0x111 },
> +	{ 0x3d400404, 0x10f3 },
> +	{ 0x3d400408, 0x72ff },
> +	{ 0x3d400490, 0x1 },
> +	{ 0x3d400494, 0xe00 },
> +	{ 0x3d400498, 0x62ffff },
> +	{ 0x3d40049c, 0xe00 },
> +	{ 0x3d4004a0, 0xffff },
> +};
> +
> +/* PHY Initialize Configuration */
> +static struct dram_cfg_param ddr_ddrphy_cfg[] = {
> +	{ 0x100a0, 0x2 },
> +	{ 0x100a1, 0x3 },
> +	{ 0x100a2, 0x0 },
> +	{ 0x100a3, 0x1 },
> +	{ 0x100a4, 0x5 },
> +	{ 0x100a5, 0x7 },
> +	{ 0x100a6, 0x6 },
> +	{ 0x100a7, 0x4 },
> +	{ 0x110a0, 0x2 },
> +	{ 0x110a1, 0x1 },
> +	{ 0x110a2, 0x3 },
> +	{ 0x110a3, 0x0 },
> +	{ 0x110a4, 0x6 },
> +	{ 0x110a5, 0x7 },
> +	{ 0x110a6, 0x4 },
> +	{ 0x110a7, 0x5 },
> +	{ 0x120a0, 0x4 },
> +	{ 0x120a1, 0x5 },
> +	{ 0x120a2, 0x7 },
> +	{ 0x120a3, 0x6 },
> +	{ 0x120a4, 0x1 },
> +	{ 0x120a5, 0x3 },
> +	{ 0x120a6, 0x2 },
> +	{ 0x120a7, 0x0 },
> +	{ 0x130a0, 0x4 },
> +	{ 0x130a1, 0x5 },
> +	{ 0x130a2, 0x7 },
> +	{ 0x130a3, 0x6 },
> +	{ 0x130a4, 0x2 },
> +	{ 0x130a5, 0x1 },
> +	{ 0x130a6, 0x0 },
> +	{ 0x130a7, 0x3 },
> +	{ 0x1005f, 0x1ff },
> +	{ 0x1015f, 0x1ff },
> +	{ 0x1105f, 0x1ff },
> +	{ 0x1115f, 0x1ff },
> +	{ 0x1205f, 0x1ff },
> +	{ 0x1215f, 0x1ff },
> +	{ 0x1305f, 0x1ff },
> +	{ 0x1315f, 0x1ff },
> +	{ 0x11005f, 0x1ff },
> +	{ 0x11015f, 0x1ff },
> +	{ 0x11105f, 0x1ff },
> +	{ 0x11115f, 0x1ff },
> +	{ 0x11205f, 0x1ff },
> +	{ 0x11215f, 0x1ff },
> +	{ 0x11305f, 0x1ff },
> +	{ 0x11315f, 0x1ff },
> +	{ 0x21005f, 0x1ff },
> +	{ 0x21015f, 0x1ff },
> +	{ 0x21105f, 0x1ff },
> +	{ 0x21115f, 0x1ff },
> +	{ 0x21205f, 0x1ff },
> +	{ 0x21215f, 0x1ff },
> +	{ 0x21305f, 0x1ff },
> +	{ 0x21315f, 0x1ff },
> +	{ 0x55, 0x1ff },
> +	{ 0x1055, 0x1ff },
> +	{ 0x2055, 0x1ff },
> +	{ 0x3055, 0x1ff },
> +	{ 0x4055, 0x1ff },
> +	{ 0x5055, 0x1ff },
> +	{ 0x6055, 0x1ff },
> +	{ 0x7055, 0x1ff },
> +	{ 0x8055, 0x1ff },
> +	{ 0x9055, 0x1ff },
> +	{ 0x200c5, 0x19 },
> +	{ 0x1200c5, 0x7 },
> +	{ 0x2200c5, 0x7 },
> +	{ 0x2002e, 0x2 },
> +	{ 0x12002e, 0x2 },
> +	{ 0x22002e, 0x2 },
> +	{ 0x90204, 0x0 },
> +	{ 0x190204, 0x0 },
> +	{ 0x290204, 0x0 },
> +	{ 0x20024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x120024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x220024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x20056, 0x3 },
> +	{ 0x120056, 0x3 },
> +	{ 0x220056, 0x3 },
> +	{ 0x1004d, 0xe00 },
> +	{ 0x1014d, 0xe00 },
> +	{ 0x1104d, 0xe00 },
> +	{ 0x1114d, 0xe00 },
> +	{ 0x1204d, 0xe00 },
> +	{ 0x1214d, 0xe00 },
> +	{ 0x1304d, 0xe00 },
> +	{ 0x1314d, 0xe00 },
> +	{ 0x11004d, 0xe00 },
> +	{ 0x11014d, 0xe00 },
> +	{ 0x11104d, 0xe00 },
> +	{ 0x11114d, 0xe00 },
> +	{ 0x11204d, 0xe00 },
> +	{ 0x11214d, 0xe00 },
> +	{ 0x11304d, 0xe00 },
> +	{ 0x11314d, 0xe00 },
> +	{ 0x21004d, 0xe00 },
> +	{ 0x21014d, 0xe00 },
> +	{ 0x21104d, 0xe00 },
> +	{ 0x21114d, 0xe00 },
> +	{ 0x21204d, 0xe00 },
> +	{ 0x21214d, 0xe00 },
> +	{ 0x21304d, 0xe00 },
> +	{ 0x21314d, 0xe00 },
> +	{ 0x10049, 0xeba },
> +	{ 0x10149, 0xeba },
> +	{ 0x11049, 0xeba },
> +	{ 0x11149, 0xeba },
> +	{ 0x12049, 0xeba },
> +	{ 0x12149, 0xeba },
> +	{ 0x13049, 0xeba },
> +	{ 0x13149, 0xeba },
> +	{ 0x110049, 0xeba },
> +	{ 0x110149, 0xeba },
> +	{ 0x111049, 0xeba },
> +	{ 0x111149, 0xeba },
> +	{ 0x112049, 0xeba },
> +	{ 0x112149, 0xeba },
> +	{ 0x113049, 0xeba },
> +	{ 0x113149, 0xeba },
> +	{ 0x210049, 0xeba },
> +	{ 0x210149, 0xeba },
> +	{ 0x211049, 0xeba },
> +	{ 0x211149, 0xeba },
> +	{ 0x212049, 0xeba },
> +	{ 0x212149, 0xeba },
> +	{ 0x213049, 0xeba },
> +	{ 0x213149, 0xeba },
> +	{ 0x43, 0x63 },
> +	{ 0x1043, 0x63 },
> +	{ 0x2043, 0x63 },
> +	{ 0x3043, 0x63 },
> +	{ 0x4043, 0x63 },
> +	{ 0x5043, 0x63 },
> +	{ 0x6043, 0x63 },
> +	{ 0x7043, 0x63 },
> +	{ 0x8043, 0x63 },
> +	{ 0x9043, 0x63 },
> +	{ 0x20018, 0x3 },
> +	{ 0x20075, 0x4 },
> +	{ 0x20050, 0x0 },
> +	{ 0x20008, 0x320 },
> +	{ 0x120008, 0x64 },
> +	{ 0x220008, 0x19 },
> +	{ 0x20088, 0x9 },
> +	{ 0x200b2, 0xdc },
> +	{ 0x10043, 0x5a1 },
> +	{ 0x10143, 0x5a1 },
> +	{ 0x11043, 0x5a1 },
> +	{ 0x11143, 0x5a1 },
> +	{ 0x12043, 0x5a1 },
> +	{ 0x12143, 0x5a1 },
> +	{ 0x13043, 0x5a1 },
> +	{ 0x13143, 0x5a1 },
> +	{ 0x1200b2, 0xdc },
> +	{ 0x110043, 0x5a1 },
> +	{ 0x110143, 0x5a1 },
> +	{ 0x111043, 0x5a1 },
> +	{ 0x111143, 0x5a1 },
> +	{ 0x112043, 0x5a1 },
> +	{ 0x112143, 0x5a1 },
> +	{ 0x113043, 0x5a1 },
> +	{ 0x113143, 0x5a1 },
> +	{ 0x2200b2, 0xdc },
> +	{ 0x210043, 0x5a1 },
> +	{ 0x210143, 0x5a1 },
> +	{ 0x211043, 0x5a1 },
> +	{ 0x211143, 0x5a1 },
> +	{ 0x212043, 0x5a1 },
> +	{ 0x212143, 0x5a1 },
> +	{ 0x213043, 0x5a1 },
> +	{ 0x213143, 0x5a1 },
> +	{ 0x200fa, 0x1 },
> +	{ 0x1200fa, 0x1 },
> +	{ 0x2200fa, 0x1 },
> +	{ 0x20019, 0x1 },
> +	{ 0x120019, 0x1 },
> +	{ 0x220019, 0x1 },
> +	{ 0x200f0, 0x660 },
> +	{ 0x200f1, 0x0 },
> +	{ 0x200f2, 0x4444 },
> +	{ 0x200f3, 0x8888 },
> +	{ 0x200f4, 0x5665 },
> +	{ 0x200f5, 0x0 },
> +	{ 0x200f6, 0x0 },
> +	{ 0x200f7, 0xf000 },
> +	{ 0x20025, 0x0 },
> +	{ 0x2002d, 0x0 },
> +	{ 0x12002d, 0x0 },
> +	{ 0x22002d, 0x0 },
> +	{ 0x200c7, 0x80 },
> +	{ 0x1200c7, 0x80 },
> +	{ 0x2200c7, 0x80 },
> +	{ 0x200ca, 0x106 },
> +	{ 0x1200ca, 0x106 },
> +	{ 0x2200ca, 0x106 },
> +	{ 0x20110, 0x2 },
> +	{ 0x20111, 0x3 },
> +	{ 0x20112, 0x4 },
> +	{ 0x20113, 0x5 },
> +	{ 0x20114, 0x0 },
> +	{ 0x20115, 0x1 },
> +};
> +
> +/* ddr phy trained csr */
> +static struct dram_cfg_param ddr_ddrphy_trained_csr[] = {
> +	{ 0x200b2, 0x0 },
> +	{ 0x1200b2, 0x0 },
> +	{ 0x2200b2, 0x0 },
> +	{ 0x200cb, 0x0 },
> +	{ 0x10043, 0x0 },
> +	{ 0x110043, 0x0 },
> +	{ 0x210043, 0x0 },
> +	{ 0x10143, 0x0 },
> +	{ 0x110143, 0x0 },
> +	{ 0x210143, 0x0 },
> +	{ 0x11043, 0x0 },
> +	{ 0x111043, 0x0 },
> +	{ 0x211043, 0x0 },
> +	{ 0x11143, 0x0 },
> +	{ 0x111143, 0x0 },
> +	{ 0x211143, 0x0 },
> +	{ 0x12043, 0x0 },
> +	{ 0x112043, 0x0 },
> +	{ 0x212043, 0x0 },
> +	{ 0x12143, 0x0 },
> +	{ 0x112143, 0x0 },
> +	{ 0x212143, 0x0 },
> +	{ 0x13043, 0x0 },
> +	{ 0x113043, 0x0 },
> +	{ 0x213043, 0x0 },
> +	{ 0x13143, 0x0 },
> +	{ 0x113143, 0x0 },
> +	{ 0x213143, 0x0 },
> +	{ 0x80, 0x0 },
> +	{ 0x100080, 0x0 },
> +	{ 0x200080, 0x0 },
> +	{ 0x1080, 0x0 },
> +	{ 0x101080, 0x0 },
> +	{ 0x201080, 0x0 },
> +	{ 0x2080, 0x0 },
> +	{ 0x102080, 0x0 },
> +	{ 0x202080, 0x0 },
> +	{ 0x3080, 0x0 },
> +	{ 0x103080, 0x0 },
> +	{ 0x203080, 0x0 },
> +	{ 0x4080, 0x0 },
> +	{ 0x104080, 0x0 },
> +	{ 0x204080, 0x0 },
> +	{ 0x5080, 0x0 },
> +	{ 0x105080, 0x0 },
> +	{ 0x205080, 0x0 },
> +	{ 0x6080, 0x0 },
> +	{ 0x106080, 0x0 },
> +	{ 0x206080, 0x0 },
> +	{ 0x7080, 0x0 },
> +	{ 0x107080, 0x0 },
> +	{ 0x207080, 0x0 },
> +	{ 0x8080, 0x0 },
> +	{ 0x108080, 0x0 },
> +	{ 0x208080, 0x0 },
> +	{ 0x9080, 0x0 },
> +	{ 0x109080, 0x0 },
> +	{ 0x209080, 0x0 },
> +	{ 0x10080, 0x0 },
> +	{ 0x110080, 0x0 },
> +	{ 0x210080, 0x0 },
> +	{ 0x10180, 0x0 },
> +	{ 0x110180, 0x0 },
> +	{ 0x210180, 0x0 },
> +	{ 0x11080, 0x0 },
> +	{ 0x111080, 0x0 },
> +	{ 0x211080, 0x0 },
> +	{ 0x11180, 0x0 },
> +	{ 0x111180, 0x0 },
> +	{ 0x211180, 0x0 },
> +	{ 0x12080, 0x0 },
> +	{ 0x112080, 0x0 },
> +	{ 0x212080, 0x0 },
> +	{ 0x12180, 0x0 },
> +	{ 0x112180, 0x0 },
> +	{ 0x212180, 0x0 },
> +	{ 0x13080, 0x0 },
> +	{ 0x113080, 0x0 },
> +	{ 0x213080, 0x0 },
> +	{ 0x13180, 0x0 },
> +	{ 0x113180, 0x0 },
> +	{ 0x213180, 0x0 },
> +	{ 0x10081, 0x0 },
> +	{ 0x110081, 0x0 },
> +	{ 0x210081, 0x0 },
> +	{ 0x10181, 0x0 },
> +	{ 0x110181, 0x0 },
> +	{ 0x210181, 0x0 },
> +	{ 0x11081, 0x0 },
> +	{ 0x111081, 0x0 },
> +	{ 0x211081, 0x0 },
> +	{ 0x11181, 0x0 },
> +	{ 0x111181, 0x0 },
> +	{ 0x211181, 0x0 },
> +	{ 0x12081, 0x0 },
> +	{ 0x112081, 0x0 },
> +	{ 0x212081, 0x0 },
> +	{ 0x12181, 0x0 },
> +	{ 0x112181, 0x0 },
> +	{ 0x212181, 0x0 },
> +	{ 0x13081, 0x0 },
> +	{ 0x113081, 0x0 },
> +	{ 0x213081, 0x0 },
> +	{ 0x13181, 0x0 },
> +	{ 0x113181, 0x0 },
> +	{ 0x213181, 0x0 },
> +	{ 0x100d0, 0x0 },
> +	{ 0x1100d0, 0x0 },
> +	{ 0x2100d0, 0x0 },
> +	{ 0x101d0, 0x0 },
> +	{ 0x1101d0, 0x0 },
> +	{ 0x2101d0, 0x0 },
> +	{ 0x110d0, 0x0 },
> +	{ 0x1110d0, 0x0 },
> +	{ 0x2110d0, 0x0 },
> +	{ 0x111d0, 0x0 },
> +	{ 0x1111d0, 0x0 },
> +	{ 0x2111d0, 0x0 },
> +	{ 0x120d0, 0x0 },
> +	{ 0x1120d0, 0x0 },
> +	{ 0x2120d0, 0x0 },
> +	{ 0x121d0, 0x0 },
> +	{ 0x1121d0, 0x0 },
> +	{ 0x2121d0, 0x0 },
> +	{ 0x130d0, 0x0 },
> +	{ 0x1130d0, 0x0 },
> +	{ 0x2130d0, 0x0 },
> +	{ 0x131d0, 0x0 },
> +	{ 0x1131d0, 0x0 },
> +	{ 0x2131d0, 0x0 },
> +	{ 0x100d1, 0x0 },
> +	{ 0x1100d1, 0x0 },
> +	{ 0x2100d1, 0x0 },
> +	{ 0x101d1, 0x0 },
> +	{ 0x1101d1, 0x0 },
> +	{ 0x2101d1, 0x0 },
> +	{ 0x110d1, 0x0 },
> +	{ 0x1110d1, 0x0 },
> +	{ 0x2110d1, 0x0 },
> +	{ 0x111d1, 0x0 },
> +	{ 0x1111d1, 0x0 },
> +	{ 0x2111d1, 0x0 },
> +	{ 0x120d1, 0x0 },
> +	{ 0x1120d1, 0x0 },
> +	{ 0x2120d1, 0x0 },
> +	{ 0x121d1, 0x0 },
> +	{ 0x1121d1, 0x0 },
> +	{ 0x2121d1, 0x0 },
> +	{ 0x130d1, 0x0 },
> +	{ 0x1130d1, 0x0 },
> +	{ 0x2130d1, 0x0 },
> +	{ 0x131d1, 0x0 },
> +	{ 0x1131d1, 0x0 },
> +	{ 0x2131d1, 0x0 },
> +	{ 0x10068, 0x0 },
> +	{ 0x10168, 0x0 },
> +	{ 0x10268, 0x0 },
> +	{ 0x10368, 0x0 },
> +	{ 0x10468, 0x0 },
> +	{ 0x10568, 0x0 },
> +	{ 0x10668, 0x0 },
> +	{ 0x10768, 0x0 },
> +	{ 0x10868, 0x0 },
> +	{ 0x11068, 0x0 },
> +	{ 0x11168, 0x0 },
> +	{ 0x11268, 0x0 },
> +	{ 0x11368, 0x0 },
> +	{ 0x11468, 0x0 },
> +	{ 0x11568, 0x0 },
> +	{ 0x11668, 0x0 },
> +	{ 0x11768, 0x0 },
> +	{ 0x11868, 0x0 },
> +	{ 0x12068, 0x0 },
> +	{ 0x12168, 0x0 },
> +	{ 0x12268, 0x0 },
> +	{ 0x12368, 0x0 },
> +	{ 0x12468, 0x0 },
> +	{ 0x12568, 0x0 },
> +	{ 0x12668, 0x0 },
> +	{ 0x12768, 0x0 },
> +	{ 0x12868, 0x0 },
> +	{ 0x13068, 0x0 },
> +	{ 0x13168, 0x0 },
> +	{ 0x13268, 0x0 },
> +	{ 0x13368, 0x0 },
> +	{ 0x13468, 0x0 },
> +	{ 0x13568, 0x0 },
> +	{ 0x13668, 0x0 },
> +	{ 0x13768, 0x0 },
> +	{ 0x13868, 0x0 },
> +	{ 0x10069, 0x0 },
> +	{ 0x10169, 0x0 },
> +	{ 0x10269, 0x0 },
> +	{ 0x10369, 0x0 },
> +	{ 0x10469, 0x0 },
> +	{ 0x10569, 0x0 },
> +	{ 0x10669, 0x0 },
> +	{ 0x10769, 0x0 },
> +	{ 0x10869, 0x0 },
> +	{ 0x11069, 0x0 },
> +	{ 0x11169, 0x0 },
> +	{ 0x11269, 0x0 },
> +	{ 0x11369, 0x0 },
> +	{ 0x11469, 0x0 },
> +	{ 0x11569, 0x0 },
> +	{ 0x11669, 0x0 },
> +	{ 0x11769, 0x0 },
> +	{ 0x11869, 0x0 },
> +	{ 0x12069, 0x0 },
> +	{ 0x12169, 0x0 },
> +	{ 0x12269, 0x0 },
> +	{ 0x12369, 0x0 },
> +	{ 0x12469, 0x0 },
> +	{ 0x12569, 0x0 },
> +	{ 0x12669, 0x0 },
> +	{ 0x12769, 0x0 },
> +	{ 0x12869, 0x0 },
> +	{ 0x13069, 0x0 },
> +	{ 0x13169, 0x0 },
> +	{ 0x13269, 0x0 },
> +	{ 0x13369, 0x0 },
> +	{ 0x13469, 0x0 },
> +	{ 0x13569, 0x0 },
> +	{ 0x13669, 0x0 },
> +	{ 0x13769, 0x0 },
> +	{ 0x13869, 0x0 },
> +	{ 0x1008c, 0x0 },
> +	{ 0x11008c, 0x0 },
> +	{ 0x21008c, 0x0 },
> +	{ 0x1018c, 0x0 },
> +	{ 0x11018c, 0x0 },
> +	{ 0x21018c, 0x0 },
> +	{ 0x1108c, 0x0 },
> +	{ 0x11108c, 0x0 },
> +	{ 0x21108c, 0x0 },
> +	{ 0x1118c, 0x0 },
> +	{ 0x11118c, 0x0 },
> +	{ 0x21118c, 0x0 },
> +	{ 0x1208c, 0x0 },
> +	{ 0x11208c, 0x0 },
> +	{ 0x21208c, 0x0 },
> +	{ 0x1218c, 0x0 },
> +	{ 0x11218c, 0x0 },
> +	{ 0x21218c, 0x0 },
> +	{ 0x1308c, 0x0 },
> +	{ 0x11308c, 0x0 },
> +	{ 0x21308c, 0x0 },
> +	{ 0x1318c, 0x0 },
> +	{ 0x11318c, 0x0 },
> +	{ 0x21318c, 0x0 },
> +	{ 0x1008d, 0x0 },
> +	{ 0x11008d, 0x0 },
> +	{ 0x21008d, 0x0 },
> +	{ 0x1018d, 0x0 },
> +	{ 0x11018d, 0x0 },
> +	{ 0x21018d, 0x0 },
> +	{ 0x1108d, 0x0 },
> +	{ 0x11108d, 0x0 },
> +	{ 0x21108d, 0x0 },
> +	{ 0x1118d, 0x0 },
> +	{ 0x11118d, 0x0 },
> +	{ 0x21118d, 0x0 },
> +	{ 0x1208d, 0x0 },
> +	{ 0x11208d, 0x0 },
> +	{ 0x21208d, 0x0 },
> +	{ 0x1218d, 0x0 },
> +	{ 0x11218d, 0x0 },
> +	{ 0x21218d, 0x0 },
> +	{ 0x1308d, 0x0 },
> +	{ 0x11308d, 0x0 },
> +	{ 0x21308d, 0x0 },
> +	{ 0x1318d, 0x0 },
> +	{ 0x11318d, 0x0 },
> +	{ 0x21318d, 0x0 },
> +	{ 0x100c0, 0x0 },
> +	{ 0x1100c0, 0x0 },
> +	{ 0x2100c0, 0x0 },
> +	{ 0x101c0, 0x0 },
> +	{ 0x1101c0, 0x0 },
> +	{ 0x2101c0, 0x0 },
> +	{ 0x102c0, 0x0 },
> +	{ 0x1102c0, 0x0 },
> +	{ 0x2102c0, 0x0 },
> +	{ 0x103c0, 0x0 },
> +	{ 0x1103c0, 0x0 },
> +	{ 0x2103c0, 0x0 },
> +	{ 0x104c0, 0x0 },
> +	{ 0x1104c0, 0x0 },
> +	{ 0x2104c0, 0x0 },
> +	{ 0x105c0, 0x0 },
> +	{ 0x1105c0, 0x0 },
> +	{ 0x2105c0, 0x0 },
> +	{ 0x106c0, 0x0 },
> +	{ 0x1106c0, 0x0 },
> +	{ 0x2106c0, 0x0 },
> +	{ 0x107c0, 0x0 },
> +	{ 0x1107c0, 0x0 },
> +	{ 0x2107c0, 0x0 },
> +	{ 0x108c0, 0x0 },
> +	{ 0x1108c0, 0x0 },
> +	{ 0x2108c0, 0x0 },
> +	{ 0x110c0, 0x0 },
> +	{ 0x1110c0, 0x0 },
> +	{ 0x2110c0, 0x0 },
> +	{ 0x111c0, 0x0 },
> +	{ 0x1111c0, 0x0 },
> +	{ 0x2111c0, 0x0 },
> +	{ 0x112c0, 0x0 },
> +	{ 0x1112c0, 0x0 },
> +	{ 0x2112c0, 0x0 },
> +	{ 0x113c0, 0x0 },
> +	{ 0x1113c0, 0x0 },
> +	{ 0x2113c0, 0x0 },
> +	{ 0x114c0, 0x0 },
> +	{ 0x1114c0, 0x0 },
> +	{ 0x2114c0, 0x0 },
> +	{ 0x115c0, 0x0 },
> +	{ 0x1115c0, 0x0 },
> +	{ 0x2115c0, 0x0 },
> +	{ 0x116c0, 0x0 },
> +	{ 0x1116c0, 0x0 },
> +	{ 0x2116c0, 0x0 },
> +	{ 0x117c0, 0x0 },
> +	{ 0x1117c0, 0x0 },
> +	{ 0x2117c0, 0x0 },
> +	{ 0x118c0, 0x0 },
> +	{ 0x1118c0, 0x0 },
> +	{ 0x2118c0, 0x0 },
> +	{ 0x120c0, 0x0 },
> +	{ 0x1120c0, 0x0 },
> +	{ 0x2120c0, 0x0 },
> +	{ 0x121c0, 0x0 },
> +	{ 0x1121c0, 0x0 },
> +	{ 0x2121c0, 0x0 },
> +	{ 0x122c0, 0x0 },
> +	{ 0x1122c0, 0x0 },
> +	{ 0x2122c0, 0x0 },
> +	{ 0x123c0, 0x0 },
> +	{ 0x1123c0, 0x0 },
> +	{ 0x2123c0, 0x0 },
> +	{ 0x124c0, 0x0 },
> +	{ 0x1124c0, 0x0 },
> +	{ 0x2124c0, 0x0 },
> +	{ 0x125c0, 0x0 },
> +	{ 0x1125c0, 0x0 },
> +	{ 0x2125c0, 0x0 },
> +	{ 0x126c0, 0x0 },
> +	{ 0x1126c0, 0x0 },
> +	{ 0x2126c0, 0x0 },
> +	{ 0x127c0, 0x0 },
> +	{ 0x1127c0, 0x0 },
> +	{ 0x2127c0, 0x0 },
> +	{ 0x128c0, 0x0 },
> +	{ 0x1128c0, 0x0 },
> +	{ 0x2128c0, 0x0 },
> +	{ 0x130c0, 0x0 },
> +	{ 0x1130c0, 0x0 },
> +	{ 0x2130c0, 0x0 },
> +	{ 0x131c0, 0x0 },
> +	{ 0x1131c0, 0x0 },
> +	{ 0x2131c0, 0x0 },
> +	{ 0x132c0, 0x0 },
> +	{ 0x1132c0, 0x0 },
> +	{ 0x2132c0, 0x0 },
> +	{ 0x133c0, 0x0 },
> +	{ 0x1133c0, 0x0 },
> +	{ 0x2133c0, 0x0 },
> +	{ 0x134c0, 0x0 },
> +	{ 0x1134c0, 0x0 },
> +	{ 0x2134c0, 0x0 },
> +	{ 0x135c0, 0x0 },
> +	{ 0x1135c0, 0x0 },
> +	{ 0x2135c0, 0x0 },
> +	{ 0x136c0, 0x0 },
> +	{ 0x1136c0, 0x0 },
> +	{ 0x2136c0, 0x0 },
> +	{ 0x137c0, 0x0 },
> +	{ 0x1137c0, 0x0 },
> +	{ 0x2137c0, 0x0 },
> +	{ 0x138c0, 0x0 },
> +	{ 0x1138c0, 0x0 },
> +	{ 0x2138c0, 0x0 },
> +	{ 0x100c1, 0x0 },
> +	{ 0x1100c1, 0x0 },
> +	{ 0x2100c1, 0x0 },
> +	{ 0x101c1, 0x0 },
> +	{ 0x1101c1, 0x0 },
> +	{ 0x2101c1, 0x0 },
> +	{ 0x102c1, 0x0 },
> +	{ 0x1102c1, 0x0 },
> +	{ 0x2102c1, 0x0 },
> +	{ 0x103c1, 0x0 },
> +	{ 0x1103c1, 0x0 },
> +	{ 0x2103c1, 0x0 },
> +	{ 0x104c1, 0x0 },
> +	{ 0x1104c1, 0x0 },
> +	{ 0x2104c1, 0x0 },
> +	{ 0x105c1, 0x0 },
> +	{ 0x1105c1, 0x0 },
> +	{ 0x2105c1, 0x0 },
> +	{ 0x106c1, 0x0 },
> +	{ 0x1106c1, 0x0 },
> +	{ 0x2106c1, 0x0 },
> +	{ 0x107c1, 0x0 },
> +	{ 0x1107c1, 0x0 },
> +	{ 0x2107c1, 0x0 },
> +	{ 0x108c1, 0x0 },
> +	{ 0x1108c1, 0x0 },
> +	{ 0x2108c1, 0x0 },
> +	{ 0x110c1, 0x0 },
> +	{ 0x1110c1, 0x0 },
> +	{ 0x2110c1, 0x0 },
> +	{ 0x111c1, 0x0 },
> +	{ 0x1111c1, 0x0 },
> +	{ 0x2111c1, 0x0 },
> +	{ 0x112c1, 0x0 },
> +	{ 0x1112c1, 0x0 },
> +	{ 0x2112c1, 0x0 },
> +	{ 0x113c1, 0x0 },
> +	{ 0x1113c1, 0x0 },
> +	{ 0x2113c1, 0x0 },
> +	{ 0x114c1, 0x0 },
> +	{ 0x1114c1, 0x0 },
> +	{ 0x2114c1, 0x0 },
> +	{ 0x115c1, 0x0 },
> +	{ 0x1115c1, 0x0 },
> +	{ 0x2115c1, 0x0 },
> +	{ 0x116c1, 0x0 },
> +	{ 0x1116c1, 0x0 },
> +	{ 0x2116c1, 0x0 },
> +	{ 0x117c1, 0x0 },
> +	{ 0x1117c1, 0x0 },
> +	{ 0x2117c1, 0x0 },
> +	{ 0x118c1, 0x0 },
> +	{ 0x1118c1, 0x0 },
> +	{ 0x2118c1, 0x0 },
> +	{ 0x120c1, 0x0 },
> +	{ 0x1120c1, 0x0 },
> +	{ 0x2120c1, 0x0 },
> +	{ 0x121c1, 0x0 },
> +	{ 0x1121c1, 0x0 },
> +	{ 0x2121c1, 0x0 },
> +	{ 0x122c1, 0x0 },
> +	{ 0x1122c1, 0x0 },
> +	{ 0x2122c1, 0x0 },
> +	{ 0x123c1, 0x0 },
> +	{ 0x1123c1, 0x0 },
> +	{ 0x2123c1, 0x0 },
> +	{ 0x124c1, 0x0 },
> +	{ 0x1124c1, 0x0 },
> +	{ 0x2124c1, 0x0 },
> +	{ 0x125c1, 0x0 },
> +	{ 0x1125c1, 0x0 },
> +	{ 0x2125c1, 0x0 },
> +	{ 0x126c1, 0x0 },
> +	{ 0x1126c1, 0x0 },
> +	{ 0x2126c1, 0x0 },
> +	{ 0x127c1, 0x0 },
> +	{ 0x1127c1, 0x0 },
> +	{ 0x2127c1, 0x0 },
> +	{ 0x128c1, 0x0 },
> +	{ 0x1128c1, 0x0 },
> +	{ 0x2128c1, 0x0 },
> +	{ 0x130c1, 0x0 },
> +	{ 0x1130c1, 0x0 },
> +	{ 0x2130c1, 0x0 },
> +	{ 0x131c1, 0x0 },
> +	{ 0x1131c1, 0x0 },
> +	{ 0x2131c1, 0x0 },
> +	{ 0x132c1, 0x0 },
> +	{ 0x1132c1, 0x0 },
> +	{ 0x2132c1, 0x0 },
> +	{ 0x133c1, 0x0 },
> +	{ 0x1133c1, 0x0 },
> +	{ 0x2133c1, 0x0 },
> +	{ 0x134c1, 0x0 },
> +	{ 0x1134c1, 0x0 },
> +	{ 0x2134c1, 0x0 },
> +	{ 0x135c1, 0x0 },
> +	{ 0x1135c1, 0x0 },
> +	{ 0x2135c1, 0x0 },
> +	{ 0x136c1, 0x0 },
> +	{ 0x1136c1, 0x0 },
> +	{ 0x2136c1, 0x0 },
> +	{ 0x137c1, 0x0 },
> +	{ 0x1137c1, 0x0 },
> +	{ 0x2137c1, 0x0 },
> +	{ 0x138c1, 0x0 },
> +	{ 0x1138c1, 0x0 },
> +	{ 0x2138c1, 0x0 },
> +	{ 0x10020, 0x0 },
> +	{ 0x110020, 0x0 },
> +	{ 0x210020, 0x0 },
> +	{ 0x11020, 0x0 },
> +	{ 0x111020, 0x0 },
> +	{ 0x211020, 0x0 },
> +	{ 0x12020, 0x0 },
> +	{ 0x112020, 0x0 },
> +	{ 0x212020, 0x0 },
> +	{ 0x13020, 0x0 },
> +	{ 0x113020, 0x0 },
> +	{ 0x213020, 0x0 },
> +	{ 0x20072, 0x0 },
> +	{ 0x20073, 0x0 },
> +	{ 0x20074, 0x0 },
> +	{ 0x100aa, 0x0 },
> +	{ 0x110aa, 0x0 },
> +	{ 0x120aa, 0x0 },
> +	{ 0x130aa, 0x0 },
> +	{ 0x20010, 0x0 },
> +	{ 0x120010, 0x0 },
> +	{ 0x220010, 0x0 },
> +	{ 0x20011, 0x0 },
> +	{ 0x120011, 0x0 },
> +	{ 0x220011, 0x0 },
> +	{ 0x100ae, 0x0 },
> +	{ 0x1100ae, 0x0 },
> +	{ 0x2100ae, 0x0 },
> +	{ 0x100af, 0x0 },
> +	{ 0x1100af, 0x0 },
> +	{ 0x2100af, 0x0 },
> +	{ 0x110ae, 0x0 },
> +	{ 0x1110ae, 0x0 },
> +	{ 0x2110ae, 0x0 },
> +	{ 0x110af, 0x0 },
> +	{ 0x1110af, 0x0 },
> +	{ 0x2110af, 0x0 },
> +	{ 0x120ae, 0x0 },
> +	{ 0x1120ae, 0x0 },
> +	{ 0x2120ae, 0x0 },
> +	{ 0x120af, 0x0 },
> +	{ 0x1120af, 0x0 },
> +	{ 0x2120af, 0x0 },
> +	{ 0x130ae, 0x0 },
> +	{ 0x1130ae, 0x0 },
> +	{ 0x2130ae, 0x0 },
> +	{ 0x130af, 0x0 },
> +	{ 0x1130af, 0x0 },
> +	{ 0x2130af, 0x0 },
> +	{ 0x20020, 0x0 },
> +	{ 0x120020, 0x0 },
> +	{ 0x220020, 0x0 },
> +	{ 0x100a0, 0x0 },
> +	{ 0x100a1, 0x0 },
> +	{ 0x100a2, 0x0 },
> +	{ 0x100a3, 0x0 },
> +	{ 0x100a4, 0x0 },
> +	{ 0x100a5, 0x0 },
> +	{ 0x100a6, 0x0 },
> +	{ 0x100a7, 0x0 },
> +	{ 0x110a0, 0x0 },
> +	{ 0x110a1, 0x0 },
> +	{ 0x110a2, 0x0 },
> +	{ 0x110a3, 0x0 },
> +	{ 0x110a4, 0x0 },
> +	{ 0x110a5, 0x0 },
> +	{ 0x110a6, 0x0 },
> +	{ 0x110a7, 0x0 },
> +	{ 0x120a0, 0x0 },
> +	{ 0x120a1, 0x0 },
> +	{ 0x120a2, 0x0 },
> +	{ 0x120a3, 0x0 },
> +	{ 0x120a4, 0x0 },
> +	{ 0x120a5, 0x0 },
> +	{ 0x120a6, 0x0 },
> +	{ 0x120a7, 0x0 },
> +	{ 0x130a0, 0x0 },
> +	{ 0x130a1, 0x0 },
> +	{ 0x130a2, 0x0 },
> +	{ 0x130a3, 0x0 },
> +	{ 0x130a4, 0x0 },
> +	{ 0x130a5, 0x0 },
> +	{ 0x130a6, 0x0 },
> +	{ 0x130a7, 0x0 },
> +	{ 0x2007c, 0x0 },
> +	{ 0x12007c, 0x0 },
> +	{ 0x22007c, 0x0 },
> +	{ 0x2007d, 0x0 },
> +	{ 0x12007d, 0x0 },
> +	{ 0x22007d, 0x0 },
> +	{ 0x400fd, 0x0 },
> +	{ 0x400c0, 0x0 },
> +	{ 0x90201, 0x0 },
> +	{ 0x190201, 0x0 },
> +	{ 0x290201, 0x0 },
> +	{ 0x90202, 0x0 },
> +	{ 0x190202, 0x0 },
> +	{ 0x290202, 0x0 },
> +	{ 0x90203, 0x0 },
> +	{ 0x190203, 0x0 },
> +	{ 0x290203, 0x0 },
> +	{ 0x90204, 0x0 },
> +	{ 0x190204, 0x0 },
> +	{ 0x290204, 0x0 },
> +	{ 0x90205, 0x0 },
> +	{ 0x190205, 0x0 },
> +	{ 0x290205, 0x0 },
> +	{ 0x90206, 0x0 },
> +	{ 0x190206, 0x0 },
> +	{ 0x290206, 0x0 },
> +	{ 0x90207, 0x0 },
> +	{ 0x190207, 0x0 },
> +	{ 0x290207, 0x0 },
> +	{ 0x90208, 0x0 },
> +	{ 0x190208, 0x0 },
> +	{ 0x290208, 0x0 },
> +	{ 0x10062, 0x0 },
> +	{ 0x10162, 0x0 },
> +	{ 0x10262, 0x0 },
> +	{ 0x10362, 0x0 },
> +	{ 0x10462, 0x0 },
> +	{ 0x10562, 0x0 },
> +	{ 0x10662, 0x0 },
> +	{ 0x10762, 0x0 },
> +	{ 0x10862, 0x0 },
> +	{ 0x11062, 0x0 },
> +	{ 0x11162, 0x0 },
> +	{ 0x11262, 0x0 },
> +	{ 0x11362, 0x0 },
> +	{ 0x11462, 0x0 },
> +	{ 0x11562, 0x0 },
> +	{ 0x11662, 0x0 },
> +	{ 0x11762, 0x0 },
> +	{ 0x11862, 0x0 },
> +	{ 0x12062, 0x0 },
> +	{ 0x12162, 0x0 },
> +	{ 0x12262, 0x0 },
> +	{ 0x12362, 0x0 },
> +	{ 0x12462, 0x0 },
> +	{ 0x12562, 0x0 },
> +	{ 0x12662, 0x0 },
> +	{ 0x12762, 0x0 },
> +	{ 0x12862, 0x0 },
> +	{ 0x13062, 0x0 },
> +	{ 0x13162, 0x0 },
> +	{ 0x13262, 0x0 },
> +	{ 0x13362, 0x0 },
> +	{ 0x13462, 0x0 },
> +	{ 0x13562, 0x0 },
> +	{ 0x13662, 0x0 },
> +	{ 0x13762, 0x0 },
> +	{ 0x13862, 0x0 },
> +	{ 0x20077, 0x0 },
> +	{ 0x10001, 0x0 },
> +	{ 0x11001, 0x0 },
> +	{ 0x12001, 0x0 },
> +	{ 0x13001, 0x0 },
> +	{ 0x10040, 0x0 },
> +	{ 0x10140, 0x0 },
> +	{ 0x10240, 0x0 },
> +	{ 0x10340, 0x0 },
> +	{ 0x10440, 0x0 },
> +	{ 0x10540, 0x0 },
> +	{ 0x10640, 0x0 },
> +	{ 0x10740, 0x0 },
> +	{ 0x10840, 0x0 },
> +	{ 0x10030, 0x0 },
> +	{ 0x10130, 0x0 },
> +	{ 0x10230, 0x0 },
> +	{ 0x10330, 0x0 },
> +	{ 0x10430, 0x0 },
> +	{ 0x10530, 0x0 },
> +	{ 0x10630, 0x0 },
> +	{ 0x10730, 0x0 },
> +	{ 0x10830, 0x0 },
> +	{ 0x11040, 0x0 },
> +	{ 0x11140, 0x0 },
> +	{ 0x11240, 0x0 },
> +	{ 0x11340, 0x0 },
> +	{ 0x11440, 0x0 },
> +	{ 0x11540, 0x0 },
> +	{ 0x11640, 0x0 },
> +	{ 0x11740, 0x0 },
> +	{ 0x11840, 0x0 },
> +	{ 0x11030, 0x0 },
> +	{ 0x11130, 0x0 },
> +	{ 0x11230, 0x0 },
> +	{ 0x11330, 0x0 },
> +	{ 0x11430, 0x0 },
> +	{ 0x11530, 0x0 },
> +	{ 0x11630, 0x0 },
> +	{ 0x11730, 0x0 },
> +	{ 0x11830, 0x0 },
> +	{ 0x12040, 0x0 },
> +	{ 0x12140, 0x0 },
> +	{ 0x12240, 0x0 },
> +	{ 0x12340, 0x0 },
> +	{ 0x12440, 0x0 },
> +	{ 0x12540, 0x0 },
> +	{ 0x12640, 0x0 },
> +	{ 0x12740, 0x0 },
> +	{ 0x12840, 0x0 },
> +	{ 0x12030, 0x0 },
> +	{ 0x12130, 0x0 },
> +	{ 0x12230, 0x0 },
> +	{ 0x12330, 0x0 },
> +	{ 0x12430, 0x0 },
> +	{ 0x12530, 0x0 },
> +	{ 0x12630, 0x0 },
> +	{ 0x12730, 0x0 },
> +	{ 0x12830, 0x0 },
> +	{ 0x13040, 0x0 },
> +	{ 0x13140, 0x0 },
> +	{ 0x13240, 0x0 },
> +	{ 0x13340, 0x0 },
> +	{ 0x13440, 0x0 },
> +	{ 0x13540, 0x0 },
> +	{ 0x13640, 0x0 },
> +	{ 0x13740, 0x0 },
> +	{ 0x13840, 0x0 },
> +	{ 0x13030, 0x0 },
> +	{ 0x13130, 0x0 },
> +	{ 0x13230, 0x0 },
> +	{ 0x13330, 0x0 },
> +	{ 0x13430, 0x0 },
> +	{ 0x13530, 0x0 },
> +	{ 0x13630, 0x0 },
> +	{ 0x13730, 0x0 },
> +	{ 0x13830, 0x0 },
> +};
> +
> +/* P0 message block paremeter for training firmware */
> +static struct dram_cfg_param ddr_fsp0_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54003, 0xc80 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x131f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x110 },
> +	{ 0x54019, 0x2dd4 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x2dd4 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x1 },
> +	{ 0x54032, 0xd400 },
> +	{ 0x54033, 0x312d },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0xd400 },
> +	{ 0x54039, 0x312d },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P1 message block paremeter for training firmware */
> +static struct dram_cfg_param ddr_fsp1_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54002, 0x101 },
> +	{ 0x54003, 0x190 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x121f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x110 },
> +	{ 0x54019, 0x84 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x84 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x1 },
> +	{ 0x54032, 0x8400 },
> +	{ 0x54033, 0x3100 },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0x8400 },
> +	{ 0x54039, 0x3100 },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P2 message block paremeter for training firmware */
> +static struct dram_cfg_param ddr_fsp2_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54002, 0x102 },
> +	{ 0x54003, 0x64 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x121f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x110 },
> +	{ 0x54019, 0x84 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x84 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x1 },
> +	{ 0x54032, 0x8400 },
> +	{ 0x54033, 0x3100 },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0x8400 },
> +	{ 0x54039, 0x3100 },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P0 2D message block paremeter for training firmware */
> +static struct dram_cfg_param ddr_fsp0_2d_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54003, 0xc80 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x61 },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x5400d, 0x100 },
> +	{ 0x5400f, 0x100 },
> +	{ 0x54010, 0x1f7f },
> +	{ 0x54012, 0x110 },
> +	{ 0x54019, 0x2dd4 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x2dd4 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x1 },
> +	{ 0x54032, 0xd400 },
> +	{ 0x54033, 0x312d },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0xd400 },
> +	{ 0x54039, 0x312d },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* DRAM PHY init engine image */
> +static struct dram_cfg_param ddr_phy_pie[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x90000, 0x10 },
> +	{ 0x90001, 0x400 },
> +	{ 0x90002, 0x10e },
> +	{ 0x90003, 0x0 },
> +	{ 0x90004, 0x0 },
> +	{ 0x90005, 0x8 },
> +	{ 0x90029, 0xb },
> +	{ 0x9002a, 0x480 },
> +	{ 0x9002b, 0x109 },
> +	{ 0x9002c, 0x8 },
> +	{ 0x9002d, 0x448 },
> +	{ 0x9002e, 0x139 },
> +	{ 0x9002f, 0x8 },
> +	{ 0x90030, 0x478 },
> +	{ 0x90031, 0x109 },
> +	{ 0x90032, 0x0 },
> +	{ 0x90033, 0xe8 },
> +	{ 0x90034, 0x109 },
> +	{ 0x90035, 0x2 },
> +	{ 0x90036, 0x10 },
> +	{ 0x90037, 0x139 },
> +	{ 0x90038, 0xf },
> +	{ 0x90039, 0x7c0 },
> +	{ 0x9003a, 0x139 },
> +	{ 0x9003b, 0x44 },
> +	{ 0x9003c, 0x630 },
> +	{ 0x9003d, 0x159 },
> +	{ 0x9003e, 0x14f },
> +	{ 0x9003f, 0x630 },
> +	{ 0x90040, 0x159 },
> +	{ 0x90041, 0x47 },
> +	{ 0x90042, 0x630 },
> +	{ 0x90043, 0x149 },
> +	{ 0x90044, 0x4f },
> +	{ 0x90045, 0x630 },
> +	{ 0x90046, 0x179 },
> +	{ 0x90047, 0x8 },
> +	{ 0x90048, 0xe0 },
> +	{ 0x90049, 0x109 },
> +	{ 0x9004a, 0x0 },
> +	{ 0x9004b, 0x7c8 },
> +	{ 0x9004c, 0x109 },
> +	{ 0x9004d, 0x0 },
> +	{ 0x9004e, 0x1 },
> +	{ 0x9004f, 0x8 },
> +	{ 0x90050, 0x0 },
> +	{ 0x90051, 0x45a },
> +	{ 0x90052, 0x9 },
> +	{ 0x90053, 0x0 },
> +	{ 0x90054, 0x448 },
> +	{ 0x90055, 0x109 },
> +	{ 0x90056, 0x40 },
> +	{ 0x90057, 0x630 },
> +	{ 0x90058, 0x179 },
> +	{ 0x90059, 0x1 },
> +	{ 0x9005a, 0x618 },
> +	{ 0x9005b, 0x109 },
> +	{ 0x9005c, 0x40c0 },
> +	{ 0x9005d, 0x630 },
> +	{ 0x9005e, 0x149 },
> +	{ 0x9005f, 0x8 },
> +	{ 0x90060, 0x4 },
> +	{ 0x90061, 0x48 },
> +	{ 0x90062, 0x4040 },
> +	{ 0x90063, 0x630 },
> +	{ 0x90064, 0x149 },
> +	{ 0x90065, 0x0 },
> +	{ 0x90066, 0x4 },
> +	{ 0x90067, 0x48 },
> +	{ 0x90068, 0x40 },
> +	{ 0x90069, 0x630 },
> +	{ 0x9006a, 0x149 },
> +	{ 0x9006b, 0x10 },
> +	{ 0x9006c, 0x4 },
> +	{ 0x9006d, 0x18 },
> +	{ 0x9006e, 0x0 },
> +	{ 0x9006f, 0x4 },
> +	{ 0x90070, 0x78 },
> +	{ 0x90071, 0x549 },
> +	{ 0x90072, 0x630 },
> +	{ 0x90073, 0x159 },
> +	{ 0x90074, 0xd49 },
> +	{ 0x90075, 0x630 },
> +	{ 0x90076, 0x159 },
> +	{ 0x90077, 0x94a },
> +	{ 0x90078, 0x630 },
> +	{ 0x90079, 0x159 },
> +	{ 0x9007a, 0x441 },
> +	{ 0x9007b, 0x630 },
> +	{ 0x9007c, 0x149 },
> +	{ 0x9007d, 0x42 },
> +	{ 0x9007e, 0x630 },
> +	{ 0x9007f, 0x149 },
> +	{ 0x90080, 0x1 },
> +	{ 0x90081, 0x630 },
> +	{ 0x90082, 0x149 },
> +	{ 0x90083, 0x0 },
> +	{ 0x90084, 0xe0 },
> +	{ 0x90085, 0x109 },
> +	{ 0x90086, 0xa },
> +	{ 0x90087, 0x10 },
> +	{ 0x90088, 0x109 },
> +	{ 0x90089, 0x9 },
> +	{ 0x9008a, 0x3c0 },
> +	{ 0x9008b, 0x149 },
> +	{ 0x9008c, 0x9 },
> +	{ 0x9008d, 0x3c0 },
> +	{ 0x9008e, 0x159 },
> +	{ 0x9008f, 0x18 },
> +	{ 0x90090, 0x10 },
> +	{ 0x90091, 0x109 },
> +	{ 0x90092, 0x0 },
> +	{ 0x90093, 0x3c0 },
> +	{ 0x90094, 0x109 },
> +	{ 0x90095, 0x18 },
> +	{ 0x90096, 0x4 },
> +	{ 0x90097, 0x48 },
> +	{ 0x90098, 0x18 },
> +	{ 0x90099, 0x4 },
> +	{ 0x9009a, 0x58 },
> +	{ 0x9009b, 0xa },
> +	{ 0x9009c, 0x10 },
> +	{ 0x9009d, 0x109 },
> +	{ 0x9009e, 0x2 },
> +	{ 0x9009f, 0x10 },
> +	{ 0x900a0, 0x109 },
> +	{ 0x900a1, 0x5 },
> +	{ 0x900a2, 0x7c0 },
> +	{ 0x900a3, 0x109 },
> +	{ 0x900a4, 0x10 },
> +	{ 0x900a5, 0x10 },
> +	{ 0x900a6, 0x109 },
> +	{ 0x40000, 0x811 },
> +	{ 0x40020, 0x880 },
> +	{ 0x40040, 0x0 },
> +	{ 0x40060, 0x0 },
> +	{ 0x40001, 0x4008 },
> +	{ 0x40021, 0x83 },
> +	{ 0x40041, 0x4f },
> +	{ 0x40061, 0x0 },
> +	{ 0x40002, 0x4040 },
> +	{ 0x40022, 0x83 },
> +	{ 0x40042, 0x51 },
> +	{ 0x40062, 0x0 },
> +	{ 0x40003, 0x811 },
> +	{ 0x40023, 0x880 },
> +	{ 0x40043, 0x0 },
> +	{ 0x40063, 0x0 },
> +	{ 0x40004, 0x720 },
> +	{ 0x40024, 0xf },
> +	{ 0x40044, 0x1740 },
> +	{ 0x40064, 0x0 },
> +	{ 0x40005, 0x16 },
> +	{ 0x40025, 0x83 },
> +	{ 0x40045, 0x4b },
> +	{ 0x40065, 0x0 },
> +	{ 0x40006, 0x716 },
> +	{ 0x40026, 0xf },
> +	{ 0x40046, 0x2001 },
> +	{ 0x40066, 0x0 },
> +	{ 0x40007, 0x716 },
> +	{ 0x40027, 0xf },
> +	{ 0x40047, 0x2800 },
> +	{ 0x40067, 0x0 },
> +	{ 0x40008, 0x716 },
> +	{ 0x40028, 0xf },
> +	{ 0x40048, 0xf00 },
> +	{ 0x40068, 0x0 },
> +	{ 0x40009, 0x720 },
> +	{ 0x40029, 0xf },
> +	{ 0x40049, 0x1400 },
> +	{ 0x40069, 0x0 },
> +	{ 0x4000a, 0xe08 },
> +	{ 0x4002a, 0xc15 },
> +	{ 0x4004a, 0x0 },
> +	{ 0x4006a, 0x0 },
> +	{ 0x4000b, 0x623 },
> +	{ 0x4002b, 0x15 },
> +	{ 0x4004b, 0x0 },
> +	{ 0x4006b, 0x0 },
> +	{ 0x4000c, 0x4028 },
> +	{ 0x4002c, 0x80 },
> +	{ 0x4004c, 0x0 },
> +	{ 0x4006c, 0x0 },
> +	{ 0x4000d, 0xe08 },
> +	{ 0x4002d, 0xc1a },
> +	{ 0x4004d, 0x0 },
> +	{ 0x4006d, 0x0 },
> +	{ 0x4000e, 0x623 },
> +	{ 0x4002e, 0x1a },
> +	{ 0x4004e, 0x0 },
> +	{ 0x4006e, 0x0 },
> +	{ 0x4000f, 0x4040 },
> +	{ 0x4002f, 0x80 },
> +	{ 0x4004f, 0x0 },
> +	{ 0x4006f, 0x0 },
> +	{ 0x40010, 0x2604 },
> +	{ 0x40030, 0x15 },
> +	{ 0x40050, 0x0 },
> +	{ 0x40070, 0x0 },
> +	{ 0x40011, 0x708 },
> +	{ 0x40031, 0x5 },
> +	{ 0x40051, 0x0 },
> +	{ 0x40071, 0x2002 },
> +	{ 0x40012, 0x8 },
> +	{ 0x40032, 0x80 },
> +	{ 0x40052, 0x0 },
> +	{ 0x40072, 0x0 },
> +	{ 0x40013, 0x2604 },
> +	{ 0x40033, 0x1a },
> +	{ 0x40053, 0x0 },
> +	{ 0x40073, 0x0 },
> +	{ 0x40014, 0x708 },
> +	{ 0x40034, 0xa },
> +	{ 0x40054, 0x0 },
> +	{ 0x40074, 0x2002 },
> +	{ 0x40015, 0x4040 },
> +	{ 0x40035, 0x80 },
> +	{ 0x40055, 0x0 },
> +	{ 0x40075, 0x0 },
> +	{ 0x40016, 0x60a },
> +	{ 0x40036, 0x15 },
> +	{ 0x40056, 0x1200 },
> +	{ 0x40076, 0x0 },
> +	{ 0x40017, 0x61a },
> +	{ 0x40037, 0x15 },
> +	{ 0x40057, 0x1300 },
> +	{ 0x40077, 0x0 },
> +	{ 0x40018, 0x60a },
> +	{ 0x40038, 0x1a },
> +	{ 0x40058, 0x1200 },
> +	{ 0x40078, 0x0 },
> +	{ 0x40019, 0x642 },
> +	{ 0x40039, 0x1a },
> +	{ 0x40059, 0x1300 },
> +	{ 0x40079, 0x0 },
> +	{ 0x4001a, 0x4808 },
> +	{ 0x4003a, 0x880 },
> +	{ 0x4005a, 0x0 },
> +	{ 0x4007a, 0x0 },
> +	{ 0x900a7, 0x0 },
> +	{ 0x900a8, 0x790 },
> +	{ 0x900a9, 0x11a },
> +	{ 0x900aa, 0x8 },
> +	{ 0x900ab, 0x7aa },
> +	{ 0x900ac, 0x2a },
> +	{ 0x900ad, 0x10 },
> +	{ 0x900ae, 0x7b2 },
> +	{ 0x900af, 0x2a },
> +	{ 0x900b0, 0x0 },
> +	{ 0x900b1, 0x7c8 },
> +	{ 0x900b2, 0x109 },
> +	{ 0x900b3, 0x10 },
> +	{ 0x900b4, 0x2a8 },
> +	{ 0x900b5, 0x129 },
> +	{ 0x900b6, 0x8 },
> +	{ 0x900b7, 0x370 },
> +	{ 0x900b8, 0x129 },
> +	{ 0x900b9, 0xa },
> +	{ 0x900ba, 0x3c8 },
> +	{ 0x900bb, 0x1a9 },
> +	{ 0x900bc, 0xc },
> +	{ 0x900bd, 0x408 },
> +	{ 0x900be, 0x199 },
> +	{ 0x900bf, 0x14 },
> +	{ 0x900c0, 0x790 },
> +	{ 0x900c1, 0x11a },
> +	{ 0x900c2, 0x8 },
> +	{ 0x900c3, 0x4 },
> +	{ 0x900c4, 0x18 },
> +	{ 0x900c5, 0xe },
> +	{ 0x900c6, 0x408 },
> +	{ 0x900c7, 0x199 },
> +	{ 0x900c8, 0x8 },
> +	{ 0x900c9, 0x8568 },
> +	{ 0x900ca, 0x108 },
> +	{ 0x900cb, 0x18 },
> +	{ 0x900cc, 0x790 },
> +	{ 0x900cd, 0x16a },
> +	{ 0x900ce, 0x8 },
> +	{ 0x900cf, 0x1d8 },
> +	{ 0x900d0, 0x169 },
> +	{ 0x900d1, 0x10 },
> +	{ 0x900d2, 0x8558 },
> +	{ 0x900d3, 0x168 },
> +	{ 0x900d4, 0x70 },
> +	{ 0x900d5, 0x788 },
> +	{ 0x900d6, 0x16a },
> +	{ 0x900d7, 0x1ff8 },
> +	{ 0x900d8, 0x85a8 },
> +	{ 0x900d9, 0x1e8 },
> +	{ 0x900da, 0x50 },
> +	{ 0x900db, 0x798 },
> +	{ 0x900dc, 0x16a },
> +	{ 0x900dd, 0x60 },
> +	{ 0x900de, 0x7a0 },
> +	{ 0x900df, 0x16a },
> +	{ 0x900e0, 0x8 },
> +	{ 0x900e1, 0x8310 },
> +	{ 0x900e2, 0x168 },
> +	{ 0x900e3, 0x8 },
> +	{ 0x900e4, 0xa310 },
> +	{ 0x900e5, 0x168 },
> +	{ 0x900e6, 0xa },
> +	{ 0x900e7, 0x408 },
> +	{ 0x900e8, 0x169 },
> +	{ 0x900e9, 0x6e },
> +	{ 0x900ea, 0x0 },
> +	{ 0x900eb, 0x68 },
> +	{ 0x900ec, 0x0 },
> +	{ 0x900ed, 0x408 },
> +	{ 0x900ee, 0x169 },
> +	{ 0x900ef, 0x0 },
> +	{ 0x900f0, 0x8310 },
> +	{ 0x900f1, 0x168 },
> +	{ 0x900f2, 0x0 },
> +	{ 0x900f3, 0xa310 },
> +	{ 0x900f4, 0x168 },
> +	{ 0x900f5, 0x1ff8 },
> +	{ 0x900f6, 0x85a8 },
> +	{ 0x900f7, 0x1e8 },
> +	{ 0x900f8, 0x68 },
> +	{ 0x900f9, 0x798 },
> +	{ 0x900fa, 0x16a },
> +	{ 0x900fb, 0x78 },
> +	{ 0x900fc, 0x7a0 },
> +	{ 0x900fd, 0x16a },
> +	{ 0x900fe, 0x68 },
> +	{ 0x900ff, 0x790 },
> +	{ 0x90100, 0x16a },
> +	{ 0x90101, 0x8 },
> +	{ 0x90102, 0x8b10 },
> +	{ 0x90103, 0x168 },
> +	{ 0x90104, 0x8 },
> +	{ 0x90105, 0xab10 },
> +	{ 0x90106, 0x168 },
> +	{ 0x90107, 0xa },
> +	{ 0x90108, 0x408 },
> +	{ 0x90109, 0x169 },
> +	{ 0x9010a, 0x58 },
> +	{ 0x9010b, 0x0 },
> +	{ 0x9010c, 0x68 },
> +	{ 0x9010d, 0x0 },
> +	{ 0x9010e, 0x408 },
> +	{ 0x9010f, 0x169 },
> +	{ 0x90110, 0x0 },
> +	{ 0x90111, 0x8b10 },
> +	{ 0x90112, 0x168 },
> +	{ 0x90113, 0x0 },
> +	{ 0x90114, 0xab10 },
> +	{ 0x90115, 0x168 },
> +	{ 0x90116, 0x0 },
> +	{ 0x90117, 0x1d8 },
> +	{ 0x90118, 0x169 },
> +	{ 0x90119, 0x80 },
> +	{ 0x9011a, 0x790 },
> +	{ 0x9011b, 0x16a },
> +	{ 0x9011c, 0x18 },
> +	{ 0x9011d, 0x7aa },
> +	{ 0x9011e, 0x6a },
> +	{ 0x9011f, 0xa },
> +	{ 0x90120, 0x0 },
> +	{ 0x90121, 0x1e9 },
> +	{ 0x90122, 0x8 },
> +	{ 0x90123, 0x8080 },
> +	{ 0x90124, 0x108 },
> +	{ 0x90125, 0xf },
> +	{ 0x90126, 0x408 },
> +	{ 0x90127, 0x169 },
> +	{ 0x90128, 0xc },
> +	{ 0x90129, 0x0 },
> +	{ 0x9012a, 0x68 },
> +	{ 0x9012b, 0x9 },
> +	{ 0x9012c, 0x0 },
> +	{ 0x9012d, 0x1a9 },
> +	{ 0x9012e, 0x0 },
> +	{ 0x9012f, 0x408 },
> +	{ 0x90130, 0x169 },
> +	{ 0x90131, 0x0 },
> +	{ 0x90132, 0x8080 },
> +	{ 0x90133, 0x108 },
> +	{ 0x90134, 0x8 },
> +	{ 0x90135, 0x7aa },
> +	{ 0x90136, 0x6a },
> +	{ 0x90137, 0x0 },
> +	{ 0x90138, 0x8568 },
> +	{ 0x90139, 0x108 },
> +	{ 0x9013a, 0xb7 },
> +	{ 0x9013b, 0x790 },
> +	{ 0x9013c, 0x16a },
> +	{ 0x9013d, 0x1f },
> +	{ 0x9013e, 0x0 },
> +	{ 0x9013f, 0x68 },
> +	{ 0x90140, 0x8 },
> +	{ 0x90141, 0x8558 },
> +	{ 0x90142, 0x168 },
> +	{ 0x90143, 0xf },
> +	{ 0x90144, 0x408 },
> +	{ 0x90145, 0x169 },
> +	{ 0x90146, 0xc },
> +	{ 0x90147, 0x0 },
> +	{ 0x90148, 0x68 },
> +	{ 0x90149, 0x0 },
> +	{ 0x9014a, 0x408 },
> +	{ 0x9014b, 0x169 },
> +	{ 0x9014c, 0x0 },
> +	{ 0x9014d, 0x8558 },
> +	{ 0x9014e, 0x168 },
> +	{ 0x9014f, 0x8 },
> +	{ 0x90150, 0x3c8 },
> +	{ 0x90151, 0x1a9 },
> +	{ 0x90152, 0x3 },
> +	{ 0x90153, 0x370 },
> +	{ 0x90154, 0x129 },
> +	{ 0x90155, 0x20 },
> +	{ 0x90156, 0x2aa },
> +	{ 0x90157, 0x9 },
> +	{ 0x90158, 0x0 },
> +	{ 0x90159, 0x400 },
> +	{ 0x9015a, 0x10e },
> +	{ 0x9015b, 0x8 },
> +	{ 0x9015c, 0xe8 },
> +	{ 0x9015d, 0x109 },
> +	{ 0x9015e, 0x0 },
> +	{ 0x9015f, 0x8140 },
> +	{ 0x90160, 0x10c },
> +	{ 0x90161, 0x10 },
> +	{ 0x90162, 0x8138 },
> +	{ 0x90163, 0x10c },
> +	{ 0x90164, 0x8 },
> +	{ 0x90165, 0x7c8 },
> +	{ 0x90166, 0x101 },
> +	{ 0x90167, 0x8 },
> +	{ 0x90168, 0x0 },
> +	{ 0x90169, 0x8 },
> +	{ 0x9016a, 0x8 },
> +	{ 0x9016b, 0x448 },
> +	{ 0x9016c, 0x109 },
> +	{ 0x9016d, 0xf },
> +	{ 0x9016e, 0x7c0 },
> +	{ 0x9016f, 0x109 },
> +	{ 0x90170, 0x0 },
> +	{ 0x90171, 0xe8 },
> +	{ 0x90172, 0x109 },
> +	{ 0x90173, 0x47 },
> +	{ 0x90174, 0x630 },
> +	{ 0x90175, 0x109 },
> +	{ 0x90176, 0x8 },
> +	{ 0x90177, 0x618 },
> +	{ 0x90178, 0x109 },
> +	{ 0x90179, 0x8 },
> +	{ 0x9017a, 0xe0 },
> +	{ 0x9017b, 0x109 },
> +	{ 0x9017c, 0x0 },
> +	{ 0x9017d, 0x7c8 },
> +	{ 0x9017e, 0x109 },
> +	{ 0x9017f, 0x8 },
> +	{ 0x90180, 0x8140 },
> +	{ 0x90181, 0x10c },
> +	{ 0x90182, 0x0 },
> +	{ 0x90183, 0x1 },
> +	{ 0x90184, 0x8 },
> +	{ 0x90185, 0x8 },
> +	{ 0x90186, 0x4 },
> +	{ 0x90187, 0x8 },
> +	{ 0x90188, 0x8 },
> +	{ 0x90189, 0x7c8 },
> +	{ 0x9018a, 0x101 },
> +	{ 0x90006, 0x0 },
> +	{ 0x90007, 0x0 },
> +	{ 0x90008, 0x8 },
> +	{ 0x90009, 0x0 },
> +	{ 0x9000a, 0x0 },
> +	{ 0x9000b, 0x0 },
> +	{ 0xd00e7, 0x400 },
> +	{ 0x90017, 0x0 },
> +	{ 0x9001f, 0x2a },
> +	{ 0x90026, 0x6a },
> +	{ 0x400d0, 0x0 },
> +	{ 0x400d1, 0x101 },
> +	{ 0x400d2, 0x105 },
> +	{ 0x400d3, 0x107 },
> +	{ 0x400d4, 0x10f },
> +	{ 0x400d5, 0x202 },
> +	{ 0x400d6, 0x20a },
> +	{ 0x400d7, 0x20b },
> +	{ 0x2003a, 0x2 },
> +	{ 0x2000b, 0x64 },
> +	{ 0x2000c, 0xc8 },
> +	{ 0x2000d, 0x7d0 },
> +	{ 0x2000e, 0x2c },
> +	{ 0x12000b, 0xc },
> +	{ 0x12000c, 0x19 },
> +	{ 0x12000d, 0xfa },
> +	{ 0x12000e, 0x10 },
> +	{ 0x22000b, 0x3 },
> +	{ 0x22000c, 0x6 },
> +	{ 0x22000d, 0x3e },
> +	{ 0x22000e, 0x10 },
> +	{ 0x9000c, 0x0 },
> +	{ 0x9000d, 0x173 },
> +	{ 0x9000e, 0x60 },
> +	{ 0x9000f, 0x6110 },
> +	{ 0x90010, 0x2152 },
> +	{ 0x90011, 0xdfbd },
> +	{ 0x90012, 0x60 },
> +	{ 0x90013, 0x6152 },
> +	{ 0x20010, 0x5a },
> +	{ 0x20011, 0x3 },
> +	{ 0x120010, 0x5a },
> +	{ 0x120011, 0x3 },
> +	{ 0x220010, 0x5a },
> +	{ 0x220011, 0x3 },
> +	{ 0x40080, 0xe0 },
> +	{ 0x40081, 0x12 },
> +	{ 0x40082, 0xe0 },
> +	{ 0x40083, 0x12 },
> +	{ 0x40084, 0xe0 },
> +	{ 0x40085, 0x12 },
> +	{ 0x140080, 0xe0 },
> +	{ 0x140081, 0x12 },
> +	{ 0x140082, 0xe0 },
> +	{ 0x140083, 0x12 },
> +	{ 0x140084, 0xe0 },
> +	{ 0x140085, 0x12 },
> +	{ 0x240080, 0xe0 },
> +	{ 0x240081, 0x12 },
> +	{ 0x240082, 0xe0 },
> +	{ 0x240083, 0x12 },
> +	{ 0x240084, 0xe0 },
> +	{ 0x240085, 0x12 },
> +	{ 0x400fd, 0xf },
> +	{ 0x10011, 0x1 },
> +	{ 0x10012, 0x1 },
> +	{ 0x10013, 0x180 },
> +	{ 0x10018, 0x1 },
> +	{ 0x10002, 0x6209 },
> +	{ 0x100b2, 0x1 },
> +	{ 0x101b4, 0x1 },
> +	{ 0x102b4, 0x1 },
> +	{ 0x103b4, 0x1 },
> +	{ 0x104b4, 0x1 },
> +	{ 0x105b4, 0x1 },
> +	{ 0x106b4, 0x1 },
> +	{ 0x107b4, 0x1 },
> +	{ 0x108b4, 0x1 },
> +	{ 0x11011, 0x1 },
> +	{ 0x11012, 0x1 },
> +	{ 0x11013, 0x180 },
> +	{ 0x11018, 0x1 },
> +	{ 0x11002, 0x6209 },
> +	{ 0x110b2, 0x1 },
> +	{ 0x111b4, 0x1 },
> +	{ 0x112b4, 0x1 },
> +	{ 0x113b4, 0x1 },
> +	{ 0x114b4, 0x1 },
> +	{ 0x115b4, 0x1 },
> +	{ 0x116b4, 0x1 },
> +	{ 0x117b4, 0x1 },
> +	{ 0x118b4, 0x1 },
> +	{ 0x12011, 0x1 },
> +	{ 0x12012, 0x1 },
> +	{ 0x12013, 0x180 },
> +	{ 0x12018, 0x1 },
> +	{ 0x12002, 0x6209 },
> +	{ 0x120b2, 0x1 },
> +	{ 0x121b4, 0x1 },
> +	{ 0x122b4, 0x1 },
> +	{ 0x123b4, 0x1 },
> +	{ 0x124b4, 0x1 },
> +	{ 0x125b4, 0x1 },
> +	{ 0x126b4, 0x1 },
> +	{ 0x127b4, 0x1 },
> +	{ 0x128b4, 0x1 },
> +	{ 0x13011, 0x1 },
> +	{ 0x13012, 0x1 },
> +	{ 0x13013, 0x180 },
> +	{ 0x13018, 0x1 },
> +	{ 0x13002, 0x6209 },
> +	{ 0x130b2, 0x1 },
> +	{ 0x131b4, 0x1 },
> +	{ 0x132b4, 0x1 },
> +	{ 0x133b4, 0x1 },
> +	{ 0x134b4, 0x1 },
> +	{ 0x135b4, 0x1 },
> +	{ 0x136b4, 0x1 },
> +	{ 0x137b4, 0x1 },
> +	{ 0x138b4, 0x1 },
> +	{ 0x2003a, 0x2 },
> +	{ 0xc0080, 0x2 },
> +	{ 0xd0000, 0x1 }
> +};
> +
> +static struct dram_fsp_msg ddr_dram_fsp_msg[] = {
> +	{
> +		/* P0 3200mts 1D */
> +		.drate = 3200,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp0_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_cfg),
> +	},
> +	{
> +		/* P1 400mts 1D */
> +		.drate = 400,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp1_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp1_cfg),
> +	},
> +	{
> +		/* P2 100mts 1D */
> +		.drate = 100,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp2_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp2_cfg),
> +	},
> +	{
> +		/* P0 3200mts 2D */
> +		.drate = 3200,
> +		.fw_type = FW_2D_IMAGE,
> +		.fsp_cfg = ddr_fsp0_2d_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_2d_cfg),
> +	},
> +};
> +
> +/* ddr timing config params */
> +struct dram_timing_info dram_timing_2gb = {
> +	.ddrc_cfg = ddr_ddrc_cfg,
> +	.ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg),
> +	.ddrphy_cfg = ddr_ddrphy_cfg,
> +	.ddrphy_cfg_num = ARRAY_SIZE(ddr_ddrphy_cfg),
> +	.fsp_msg = ddr_dram_fsp_msg,
> +	.fsp_msg_num = ARRAY_SIZE(ddr_dram_fsp_msg),
> +	.ddrphy_trained_csr = ddr_ddrphy_trained_csr,
> +	.ddrphy_trained_csr_num = ARRAY_SIZE(ddr_ddrphy_trained_csr),
> +	.ddrphy_pie = ddr_phy_pie,
> +	.ddrphy_pie_num = ARRAY_SIZE(ddr_phy_pie),
> +	.fsp_table = { 3200, 400, 100, },
> +};
> +
> diff --git a/board/kontron/pitx_imx8m/lpddr4_timing_4gb.c b/board/kontron/pitx_imx8m/lpddr4_timing_4gb.c
> new file mode 100644
> index 0000000000..fd7173bff1
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/lpddr4_timing_4gb.c
> @@ -0,0 +1,1853 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <linux/kernel.h>
> +#include <asm/arch/ddr.h>
> +#include <asm/arch/lpddr4_define.h>
> +
> +static struct dram_cfg_param ddr_ddrc_cfg[] = {
> +	/** Initialize DDRC registers **/
> +	{ 0x3d400304, 0x1 },
> +	{ 0x3d400030, 0x1 },
> +	{ 0x3d400000, 0xa3080020 },
> +	{ 0x3d400028, 0x0 },
> +	{ 0x3d400020, 0x202 },
> +	{ 0x3d400024, 0x3e800 },
> +	{ 0x3d400064, 0x1800e0 },
> +	{ 0x3d4000d0, 0xc003061c },
> +	{ 0x3d4000d4, 0x9e0000 },
> +	{ 0x3d4000dc, 0xd4002d },
> +	{ 0x3d4000e0, 0x310008 },
> +	{ 0x3d4000e8, 0x66004a },
> +	{ 0x3d4000ec, 0x16004a },
> +	{ 0x3d400100, 0x1a200624 },
> +	{ 0x3d400104, 0x60636 },
> +	{ 0x3d40010c, 0xc0c000 },
> +	{ 0x3d400110, 0x10040a10 },
> +	{ 0x3d400114, 0x2040c0c },
> +	{ 0x3d400118, 0x1010007 },
> +	{ 0x3d40011c, 0x401 },
> +	{ 0x3d400130, 0x20600 },
> +	{ 0x3d400134, 0xc100002 },
> +	{ 0x3d400138, 0xe6 },
> +	{ 0x3d400144, 0xa00050 },
> +	{ 0x3d400180, 0xc3200018 },
> +	{ 0x3d400184, 0x28061a8 },
> +	{ 0x3d400188, 0x0 },
> +	{ 0x3d400190, 0x497820a },
> +	{ 0x3d400194, 0x80303 },
> +	{ 0x3d4001a0, 0xe0400018 },
> +	{ 0x3d4001a4, 0xdf00e4 },
> +	{ 0x3d4001a8, 0x80000000 },
> +	{ 0x3d4001b0, 0x11 },
> +	{ 0x3d4001b4, 0x170a },
> +	{ 0x3d4001c0, 0x1 },
> +	{ 0x3d4001c4, 0x1 },
> +	{ 0x3d4000f4, 0x639 },
> +	{ 0x3d400108, 0x70e1617 },
> +	{ 0x3d400200, 0x17 },
> +	{ 0x3d40020c, 0x0 },
> +	{ 0x3d400210, 0x1f1f },
> +	{ 0x3d400204, 0x80808 },
> +	{ 0x3d400214, 0x7070707 },
> +	{ 0x3d400218, 0x7070707 },
> +	{ 0x3d402020, 0x0 },
> +	{ 0x3d402024, 0x7d00 },
> +	{ 0x3d402050, 0x20d040 },
> +	{ 0x3d402064, 0x3001c },
> +	{ 0x3d4020dc, 0x840000 },
> +	{ 0x3d4020e0, 0x310000 },
> +	{ 0x3d4020e8, 0x66004a },
> +	{ 0x3d4020ec, 0x16004a },
> +	{ 0x3d402100, 0xa040005 },
> +	{ 0x3d402104, 0x30407 },
> +	{ 0x3d402108, 0x203060b },
> +	{ 0x3d40210c, 0x505000 },
> +	{ 0x3d402110, 0x2040202 },
> +	{ 0x3d402114, 0x2030202 },
> +	{ 0x3d402118, 0x1010004 },
> +	{ 0x3d40211c, 0x301 },
> +	{ 0x3d402130, 0x20300 },
> +	{ 0x3d402134, 0xa100002 },
> +	{ 0x3d402138, 0x1d },
> +	{ 0x3d402144, 0x14000a },
> +	{ 0x3d402180, 0xc0640004 },
> +	{ 0x3d402190, 0x3818200 },
> +	{ 0x3d402194, 0x80303 },
> +	{ 0x3d4021b4, 0x100 },
> +	{ 0x3d403020, 0x0 },
> +	{ 0x3d403024, 0x1f40 },
> +	{ 0x3d403050, 0x20d040 },
> +	{ 0x3d403064, 0x30007 },
> +	{ 0x3d4030dc, 0x840000 },
> +	{ 0x3d4030e0, 0x310000 },
> +	{ 0x3d4030e8, 0x66004a },
> +	{ 0x3d4030ec, 0x16004a },
> +	{ 0x3d403100, 0xa010102 },
> +	{ 0x3d403104, 0x30404 },
> +	{ 0x3d403108, 0x203060b },
> +	{ 0x3d40310c, 0x505000 },
> +	{ 0x3d403110, 0x2040202 },
> +	{ 0x3d403114, 0x2030202 },
> +	{ 0x3d403118, 0x1010004 },
> +	{ 0x3d40311c, 0x301 },
> +	{ 0x3d403130, 0x20300 },
> +	{ 0x3d403134, 0xa100002 },
> +	{ 0x3d403138, 0x8 },
> +	{ 0x3d403144, 0x50003 },
> +	{ 0x3d403180, 0xc0190004 },
> +	{ 0x3d403190, 0x3818200 },
> +	{ 0x3d403194, 0x80303 },
> +	{ 0x3d4031b4, 0x100 },
> +	{ 0x3d400244, 0x0 },
> +	{ 0x3d400250, 0x29001505 },
> +	{ 0x3d400254, 0x2c },
> +	{ 0x3d40025c, 0x5900575b },
> +	{ 0x3d400264, 0x90000096 },
> +	{ 0x3d40026c, 0x1000012c },
> +	{ 0x3d400300, 0x16 },
> +	{ 0x3d400304, 0x0 },
> +	{ 0x3d40030c, 0x0 },
> +	{ 0x3d400320, 0x1 },
> +	{ 0x3d40036c, 0x11 },
> +	{ 0x3d400400, 0x111 },
> +	{ 0x3d400404, 0x10f3 },
> +	{ 0x3d400408, 0x72ff },
> +	{ 0x3d400490, 0x1 },
> +	{ 0x3d400494, 0xe00 },
> +	{ 0x3d400498, 0x62ffff },
> +	{ 0x3d40049c, 0xe00 },
> +	{ 0x3d4004a0, 0xffff },
> +};
> +
> +/* PHY Initialize Configuration */
> +struct dram_cfg_param ddr_ddrphy_cfg[] = {
> +	{ 0x100a0, 0x2 },
> +	{ 0x100a1, 0x3 },
> +	{ 0x100a2, 0x0 },
> +	{ 0x100a3, 0x1 },
> +	{ 0x100a4, 0x5 },
> +	{ 0x100a5, 0x7 },
> +	{ 0x100a6, 0x6 },
> +	{ 0x100a7, 0x4 },
> +	{ 0x110a0, 0x2 },
> +	{ 0x110a1, 0x1 },
> +	{ 0x110a2, 0x3 },
> +	{ 0x110a3, 0x0 },
> +	{ 0x110a4, 0x6 },
> +	{ 0x110a5, 0x7 },
> +	{ 0x110a6, 0x4 },
> +	{ 0x110a7, 0x5 },
> +	{ 0x120a0, 0x4 },
> +	{ 0x120a1, 0x5 },
> +	{ 0x120a2, 0x7 },
> +	{ 0x120a3, 0x6 },
> +	{ 0x120a4, 0x1 },
> +	{ 0x120a5, 0x3 },
> +	{ 0x120a6, 0x2 },
> +	{ 0x120a7, 0x0 },
> +	{ 0x130a0, 0x4 },
> +	{ 0x130a1, 0x5 },
> +	{ 0x130a2, 0x7 },
> +	{ 0x130a3, 0x6 },
> +	{ 0x130a4, 0x2 },
> +	{ 0x130a5, 0x1 },
> +	{ 0x130a6, 0x0 },
> +	{ 0x130a7, 0x3 },
> +	{ 0x1005f, 0x1ff },
> +	{ 0x1015f, 0x1ff },
> +	{ 0x1105f, 0x1ff },
> +	{ 0x1115f, 0x1ff },
> +	{ 0x1205f, 0x1ff },
> +	{ 0x1215f, 0x1ff },
> +	{ 0x1305f, 0x1ff },
> +	{ 0x1315f, 0x1ff },
> +	{ 0x11005f, 0x1ff },
> +	{ 0x11015f, 0x1ff },
> +	{ 0x11105f, 0x1ff },
> +	{ 0x11115f, 0x1ff },
> +	{ 0x11205f, 0x1ff },
> +	{ 0x11215f, 0x1ff },
> +	{ 0x11305f, 0x1ff },
> +	{ 0x11315f, 0x1ff },
> +	{ 0x21005f, 0x1ff },
> +	{ 0x21015f, 0x1ff },
> +	{ 0x21105f, 0x1ff },
> +	{ 0x21115f, 0x1ff },
> +	{ 0x21205f, 0x1ff },
> +	{ 0x21215f, 0x1ff },
> +	{ 0x21305f, 0x1ff },
> +	{ 0x21315f, 0x1ff },
> +	{ 0x55, 0x1ff },
> +	{ 0x1055, 0x1ff },
> +	{ 0x2055, 0x1ff },
> +	{ 0x3055, 0x1ff },
> +	{ 0x4055, 0x1ff },
> +	{ 0x5055, 0x1ff },
> +	{ 0x6055, 0x1ff },
> +	{ 0x7055, 0x1ff },
> +	{ 0x8055, 0x1ff },
> +	{ 0x9055, 0x1ff },
> +	{ 0x200c5, 0x19 },
> +	{ 0x1200c5, 0x7 },
> +	{ 0x2200c5, 0x7 },
> +	{ 0x2002e, 0x2 },
> +	{ 0x12002e, 0x2 },
> +	{ 0x22002e, 0x2 },
> +	{ 0x90204, 0x0 },
> +	{ 0x190204, 0x0 },
> +	{ 0x290204, 0x0 },
> +	{ 0x20024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x120024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x220024, 0x1ab },
> +	{ 0x2003a, 0x0 },
> +	{ 0x20056, 0x3 },
> +	{ 0x120056, 0x3 },
> +	{ 0x220056, 0x3 },
> +	{ 0x1004d, 0xe00 },
> +	{ 0x1014d, 0xe00 },
> +	{ 0x1104d, 0xe00 },
> +	{ 0x1114d, 0xe00 },
> +	{ 0x1204d, 0xe00 },
> +	{ 0x1214d, 0xe00 },
> +	{ 0x1304d, 0xe00 },
> +	{ 0x1314d, 0xe00 },
> +	{ 0x11004d, 0xe00 },
> +	{ 0x11014d, 0xe00 },
> +	{ 0x11104d, 0xe00 },
> +	{ 0x11114d, 0xe00 },
> +	{ 0x11204d, 0xe00 },
> +	{ 0x11214d, 0xe00 },
> +	{ 0x11304d, 0xe00 },
> +	{ 0x11314d, 0xe00 },
> +	{ 0x21004d, 0xe00 },
> +	{ 0x21014d, 0xe00 },
> +	{ 0x21104d, 0xe00 },
> +	{ 0x21114d, 0xe00 },
> +	{ 0x21204d, 0xe00 },
> +	{ 0x21214d, 0xe00 },
> +	{ 0x21304d, 0xe00 },
> +	{ 0x21314d, 0xe00 },
> +	{ 0x10049, 0xeba },
> +	{ 0x10149, 0xeba },
> +	{ 0x11049, 0xeba },
> +	{ 0x11149, 0xeba },
> +	{ 0x12049, 0xeba },
> +	{ 0x12149, 0xeba },
> +	{ 0x13049, 0xeba },
> +	{ 0x13149, 0xeba },
> +	{ 0x110049, 0xeba },
> +	{ 0x110149, 0xeba },
> +	{ 0x111049, 0xeba },
> +	{ 0x111149, 0xeba },
> +	{ 0x112049, 0xeba },
> +	{ 0x112149, 0xeba },
> +	{ 0x113049, 0xeba },
> +	{ 0x113149, 0xeba },
> +	{ 0x210049, 0xeba },
> +	{ 0x210149, 0xeba },
> +	{ 0x211049, 0xeba },
> +	{ 0x211149, 0xeba },
> +	{ 0x212049, 0xeba },
> +	{ 0x212149, 0xeba },
> +	{ 0x213049, 0xeba },
> +	{ 0x213149, 0xeba },
> +	{ 0x43, 0x63 },
> +	{ 0x1043, 0x63 },
> +	{ 0x2043, 0x63 },
> +	{ 0x3043, 0x63 },
> +	{ 0x4043, 0x63 },
> +	{ 0x5043, 0x63 },
> +	{ 0x6043, 0x63 },
> +	{ 0x7043, 0x63 },
> +	{ 0x8043, 0x63 },
> +	{ 0x9043, 0x63 },
> +	{ 0x20018, 0x3 },
> +	{ 0x20075, 0x4 },
> +	{ 0x20050, 0x0 },
> +	{ 0x20008, 0x320 },
> +	{ 0x120008, 0x64 },
> +	{ 0x220008, 0x19 },
> +	{ 0x20088, 0x9 },
> +	{ 0x200b2, 0xdc },
> +	{ 0x10043, 0x5a1 },
> +	{ 0x10143, 0x5a1 },
> +	{ 0x11043, 0x5a1 },
> +	{ 0x11143, 0x5a1 },
> +	{ 0x12043, 0x5a1 },
> +	{ 0x12143, 0x5a1 },
> +	{ 0x13043, 0x5a1 },
> +	{ 0x13143, 0x5a1 },
> +	{ 0x1200b2, 0xdc },
> +	{ 0x110043, 0x5a1 },
> +	{ 0x110143, 0x5a1 },
> +	{ 0x111043, 0x5a1 },
> +	{ 0x111143, 0x5a1 },
> +	{ 0x112043, 0x5a1 },
> +	{ 0x112143, 0x5a1 },
> +	{ 0x113043, 0x5a1 },
> +	{ 0x113143, 0x5a1 },
> +	{ 0x2200b2, 0xdc },
> +	{ 0x210043, 0x5a1 },
> +	{ 0x210143, 0x5a1 },
> +	{ 0x211043, 0x5a1 },
> +	{ 0x211143, 0x5a1 },
> +	{ 0x212043, 0x5a1 },
> +	{ 0x212143, 0x5a1 },
> +	{ 0x213043, 0x5a1 },
> +	{ 0x213143, 0x5a1 },
> +	{ 0x200fa, 0x1 },
> +	{ 0x1200fa, 0x1 },
> +	{ 0x2200fa, 0x1 },
> +	{ 0x20019, 0x1 },
> +	{ 0x120019, 0x1 },
> +	{ 0x220019, 0x1 },
> +	{ 0x200f0, 0x660 },
> +	{ 0x200f1, 0x0 },
> +	{ 0x200f2, 0x4444 },
> +	{ 0x200f3, 0x8888 },
> +	{ 0x200f4, 0x5665 },
> +	{ 0x200f5, 0x0 },
> +	{ 0x200f6, 0x0 },
> +	{ 0x200f7, 0xf000 },
> +	{ 0x20025, 0x0 },
> +	{ 0x2002d, 0x0 },
> +	{ 0x12002d, 0x0 },
> +	{ 0x22002d, 0x0 },
> +	{ 0x200c7, 0x80 },
> +	{ 0x1200c7, 0x80 },
> +	{ 0x2200c7, 0x80 },
> +	{ 0x200ca, 0x106 },
> +	{ 0x1200ca, 0x106 },
> +	{ 0x2200ca, 0x106 },
> +	{ 0x20110, 0x2 },
> +	{ 0x20111, 0x3 },
> +	{ 0x20112, 0x4 },
> +	{ 0x20113, 0x5 },
> +	{ 0x20114, 0x0 },
> +	{ 0x20115, 0x1 },
> +};
> +
> +/* ddr phy trained csr */
> +struct dram_cfg_param ddr_ddrphy_trained_csr[] = {
> +	{ 0x200b2, 0x0 },
> +	{ 0x1200b2, 0x0 },
> +	{ 0x2200b2, 0x0 },
> +	{ 0x200cb, 0x0 },
> +	{ 0x10043, 0x0 },
> +	{ 0x110043, 0x0 },
> +	{ 0x210043, 0x0 },
> +	{ 0x10143, 0x0 },
> +	{ 0x110143, 0x0 },
> +	{ 0x210143, 0x0 },
> +	{ 0x11043, 0x0 },
> +	{ 0x111043, 0x0 },
> +	{ 0x211043, 0x0 },
> +	{ 0x11143, 0x0 },
> +	{ 0x111143, 0x0 },
> +	{ 0x211143, 0x0 },
> +	{ 0x12043, 0x0 },
> +	{ 0x112043, 0x0 },
> +	{ 0x212043, 0x0 },
> +	{ 0x12143, 0x0 },
> +	{ 0x112143, 0x0 },
> +	{ 0x212143, 0x0 },
> +	{ 0x13043, 0x0 },
> +	{ 0x113043, 0x0 },
> +	{ 0x213043, 0x0 },
> +	{ 0x13143, 0x0 },
> +	{ 0x113143, 0x0 },
> +	{ 0x213143, 0x0 },
> +	{ 0x80, 0x0 },
> +	{ 0x100080, 0x0 },
> +	{ 0x200080, 0x0 },
> +	{ 0x1080, 0x0 },
> +	{ 0x101080, 0x0 },
> +	{ 0x201080, 0x0 },
> +	{ 0x2080, 0x0 },
> +	{ 0x102080, 0x0 },
> +	{ 0x202080, 0x0 },
> +	{ 0x3080, 0x0 },
> +	{ 0x103080, 0x0 },
> +	{ 0x203080, 0x0 },
> +	{ 0x4080, 0x0 },
> +	{ 0x104080, 0x0 },
> +	{ 0x204080, 0x0 },
> +	{ 0x5080, 0x0 },
> +	{ 0x105080, 0x0 },
> +	{ 0x205080, 0x0 },
> +	{ 0x6080, 0x0 },
> +	{ 0x106080, 0x0 },
> +	{ 0x206080, 0x0 },
> +	{ 0x7080, 0x0 },
> +	{ 0x107080, 0x0 },
> +	{ 0x207080, 0x0 },
> +	{ 0x8080, 0x0 },
> +	{ 0x108080, 0x0 },
> +	{ 0x208080, 0x0 },
> +	{ 0x9080, 0x0 },
> +	{ 0x109080, 0x0 },
> +	{ 0x209080, 0x0 },
> +	{ 0x10080, 0x0 },
> +	{ 0x110080, 0x0 },
> +	{ 0x210080, 0x0 },
> +	{ 0x10180, 0x0 },
> +	{ 0x110180, 0x0 },
> +	{ 0x210180, 0x0 },
> +	{ 0x11080, 0x0 },
> +	{ 0x111080, 0x0 },
> +	{ 0x211080, 0x0 },
> +	{ 0x11180, 0x0 },
> +	{ 0x111180, 0x0 },
> +	{ 0x211180, 0x0 },
> +	{ 0x12080, 0x0 },
> +	{ 0x112080, 0x0 },
> +	{ 0x212080, 0x0 },
> +	{ 0x12180, 0x0 },
> +	{ 0x112180, 0x0 },
> +	{ 0x212180, 0x0 },
> +	{ 0x13080, 0x0 },
> +	{ 0x113080, 0x0 },
> +	{ 0x213080, 0x0 },
> +	{ 0x13180, 0x0 },
> +	{ 0x113180, 0x0 },
> +	{ 0x213180, 0x0 },
> +	{ 0x10081, 0x0 },
> +	{ 0x110081, 0x0 },
> +	{ 0x210081, 0x0 },
> +	{ 0x10181, 0x0 },
> +	{ 0x110181, 0x0 },
> +	{ 0x210181, 0x0 },
> +	{ 0x11081, 0x0 },
> +	{ 0x111081, 0x0 },
> +	{ 0x211081, 0x0 },
> +	{ 0x11181, 0x0 },
> +	{ 0x111181, 0x0 },
> +	{ 0x211181, 0x0 },
> +	{ 0x12081, 0x0 },
> +	{ 0x112081, 0x0 },
> +	{ 0x212081, 0x0 },
> +	{ 0x12181, 0x0 },
> +	{ 0x112181, 0x0 },
> +	{ 0x212181, 0x0 },
> +	{ 0x13081, 0x0 },
> +	{ 0x113081, 0x0 },
> +	{ 0x213081, 0x0 },
> +	{ 0x13181, 0x0 },
> +	{ 0x113181, 0x0 },
> +	{ 0x213181, 0x0 },
> +	{ 0x100d0, 0x0 },
> +	{ 0x1100d0, 0x0 },
> +	{ 0x2100d0, 0x0 },
> +	{ 0x101d0, 0x0 },
> +	{ 0x1101d0, 0x0 },
> +	{ 0x2101d0, 0x0 },
> +	{ 0x110d0, 0x0 },
> +	{ 0x1110d0, 0x0 },
> +	{ 0x2110d0, 0x0 },
> +	{ 0x111d0, 0x0 },
> +	{ 0x1111d0, 0x0 },
> +	{ 0x2111d0, 0x0 },
> +	{ 0x120d0, 0x0 },
> +	{ 0x1120d0, 0x0 },
> +	{ 0x2120d0, 0x0 },
> +	{ 0x121d0, 0x0 },
> +	{ 0x1121d0, 0x0 },
> +	{ 0x2121d0, 0x0 },
> +	{ 0x130d0, 0x0 },
> +	{ 0x1130d0, 0x0 },
> +	{ 0x2130d0, 0x0 },
> +	{ 0x131d0, 0x0 },
> +	{ 0x1131d0, 0x0 },
> +	{ 0x2131d0, 0x0 },
> +	{ 0x100d1, 0x0 },
> +	{ 0x1100d1, 0x0 },
> +	{ 0x2100d1, 0x0 },
> +	{ 0x101d1, 0x0 },
> +	{ 0x1101d1, 0x0 },
> +	{ 0x2101d1, 0x0 },
> +	{ 0x110d1, 0x0 },
> +	{ 0x1110d1, 0x0 },
> +	{ 0x2110d1, 0x0 },
> +	{ 0x111d1, 0x0 },
> +	{ 0x1111d1, 0x0 },
> +	{ 0x2111d1, 0x0 },
> +	{ 0x120d1, 0x0 },
> +	{ 0x1120d1, 0x0 },
> +	{ 0x2120d1, 0x0 },
> +	{ 0x121d1, 0x0 },
> +	{ 0x1121d1, 0x0 },
> +	{ 0x2121d1, 0x0 },
> +	{ 0x130d1, 0x0 },
> +	{ 0x1130d1, 0x0 },
> +	{ 0x2130d1, 0x0 },
> +	{ 0x131d1, 0x0 },
> +	{ 0x1131d1, 0x0 },
> +	{ 0x2131d1, 0x0 },
> +	{ 0x10068, 0x0 },
> +	{ 0x10168, 0x0 },
> +	{ 0x10268, 0x0 },
> +	{ 0x10368, 0x0 },
> +	{ 0x10468, 0x0 },
> +	{ 0x10568, 0x0 },
> +	{ 0x10668, 0x0 },
> +	{ 0x10768, 0x0 },
> +	{ 0x10868, 0x0 },
> +	{ 0x11068, 0x0 },
> +	{ 0x11168, 0x0 },
> +	{ 0x11268, 0x0 },
> +	{ 0x11368, 0x0 },
> +	{ 0x11468, 0x0 },
> +	{ 0x11568, 0x0 },
> +	{ 0x11668, 0x0 },
> +	{ 0x11768, 0x0 },
> +	{ 0x11868, 0x0 },
> +	{ 0x12068, 0x0 },
> +	{ 0x12168, 0x0 },
> +	{ 0x12268, 0x0 },
> +	{ 0x12368, 0x0 },
> +	{ 0x12468, 0x0 },
> +	{ 0x12568, 0x0 },
> +	{ 0x12668, 0x0 },
> +	{ 0x12768, 0x0 },
> +	{ 0x12868, 0x0 },
> +	{ 0x13068, 0x0 },
> +	{ 0x13168, 0x0 },
> +	{ 0x13268, 0x0 },
> +	{ 0x13368, 0x0 },
> +	{ 0x13468, 0x0 },
> +	{ 0x13568, 0x0 },
> +	{ 0x13668, 0x0 },
> +	{ 0x13768, 0x0 },
> +	{ 0x13868, 0x0 },
> +	{ 0x10069, 0x0 },
> +	{ 0x10169, 0x0 },
> +	{ 0x10269, 0x0 },
> +	{ 0x10369, 0x0 },
> +	{ 0x10469, 0x0 },
> +	{ 0x10569, 0x0 },
> +	{ 0x10669, 0x0 },
> +	{ 0x10769, 0x0 },
> +	{ 0x10869, 0x0 },
> +	{ 0x11069, 0x0 },
> +	{ 0x11169, 0x0 },
> +	{ 0x11269, 0x0 },
> +	{ 0x11369, 0x0 },
> +	{ 0x11469, 0x0 },
> +	{ 0x11569, 0x0 },
> +	{ 0x11669, 0x0 },
> +	{ 0x11769, 0x0 },
> +	{ 0x11869, 0x0 },
> +	{ 0x12069, 0x0 },
> +	{ 0x12169, 0x0 },
> +	{ 0x12269, 0x0 },
> +	{ 0x12369, 0x0 },
> +	{ 0x12469, 0x0 },
> +	{ 0x12569, 0x0 },
> +	{ 0x12669, 0x0 },
> +	{ 0x12769, 0x0 },
> +	{ 0x12869, 0x0 },
> +	{ 0x13069, 0x0 },
> +	{ 0x13169, 0x0 },
> +	{ 0x13269, 0x0 },
> +	{ 0x13369, 0x0 },
> +	{ 0x13469, 0x0 },
> +	{ 0x13569, 0x0 },
> +	{ 0x13669, 0x0 },
> +	{ 0x13769, 0x0 },
> +	{ 0x13869, 0x0 },
> +	{ 0x1008c, 0x0 },
> +	{ 0x11008c, 0x0 },
> +	{ 0x21008c, 0x0 },
> +	{ 0x1018c, 0x0 },
> +	{ 0x11018c, 0x0 },
> +	{ 0x21018c, 0x0 },
> +	{ 0x1108c, 0x0 },
> +	{ 0x11108c, 0x0 },
> +	{ 0x21108c, 0x0 },
> +	{ 0x1118c, 0x0 },
> +	{ 0x11118c, 0x0 },
> +	{ 0x21118c, 0x0 },
> +	{ 0x1208c, 0x0 },
> +	{ 0x11208c, 0x0 },
> +	{ 0x21208c, 0x0 },
> +	{ 0x1218c, 0x0 },
> +	{ 0x11218c, 0x0 },
> +	{ 0x21218c, 0x0 },
> +	{ 0x1308c, 0x0 },
> +	{ 0x11308c, 0x0 },
> +	{ 0x21308c, 0x0 },
> +	{ 0x1318c, 0x0 },
> +	{ 0x11318c, 0x0 },
> +	{ 0x21318c, 0x0 },
> +	{ 0x1008d, 0x0 },
> +	{ 0x11008d, 0x0 },
> +	{ 0x21008d, 0x0 },
> +	{ 0x1018d, 0x0 },
> +	{ 0x11018d, 0x0 },
> +	{ 0x21018d, 0x0 },
> +	{ 0x1108d, 0x0 },
> +	{ 0x11108d, 0x0 },
> +	{ 0x21108d, 0x0 },
> +	{ 0x1118d, 0x0 },
> +	{ 0x11118d, 0x0 },
> +	{ 0x21118d, 0x0 },
> +	{ 0x1208d, 0x0 },
> +	{ 0x11208d, 0x0 },
> +	{ 0x21208d, 0x0 },
> +	{ 0x1218d, 0x0 },
> +	{ 0x11218d, 0x0 },
> +	{ 0x21218d, 0x0 },
> +	{ 0x1308d, 0x0 },
> +	{ 0x11308d, 0x0 },
> +	{ 0x21308d, 0x0 },
> +	{ 0x1318d, 0x0 },
> +	{ 0x11318d, 0x0 },
> +	{ 0x21318d, 0x0 },
> +	{ 0x100c0, 0x0 },
> +	{ 0x1100c0, 0x0 },
> +	{ 0x2100c0, 0x0 },
> +	{ 0x101c0, 0x0 },
> +	{ 0x1101c0, 0x0 },
> +	{ 0x2101c0, 0x0 },
> +	{ 0x102c0, 0x0 },
> +	{ 0x1102c0, 0x0 },
> +	{ 0x2102c0, 0x0 },
> +	{ 0x103c0, 0x0 },
> +	{ 0x1103c0, 0x0 },
> +	{ 0x2103c0, 0x0 },
> +	{ 0x104c0, 0x0 },
> +	{ 0x1104c0, 0x0 },
> +	{ 0x2104c0, 0x0 },
> +	{ 0x105c0, 0x0 },
> +	{ 0x1105c0, 0x0 },
> +	{ 0x2105c0, 0x0 },
> +	{ 0x106c0, 0x0 },
> +	{ 0x1106c0, 0x0 },
> +	{ 0x2106c0, 0x0 },
> +	{ 0x107c0, 0x0 },
> +	{ 0x1107c0, 0x0 },
> +	{ 0x2107c0, 0x0 },
> +	{ 0x108c0, 0x0 },
> +	{ 0x1108c0, 0x0 },
> +	{ 0x2108c0, 0x0 },
> +	{ 0x110c0, 0x0 },
> +	{ 0x1110c0, 0x0 },
> +	{ 0x2110c0, 0x0 },
> +	{ 0x111c0, 0x0 },
> +	{ 0x1111c0, 0x0 },
> +	{ 0x2111c0, 0x0 },
> +	{ 0x112c0, 0x0 },
> +	{ 0x1112c0, 0x0 },
> +	{ 0x2112c0, 0x0 },
> +	{ 0x113c0, 0x0 },
> +	{ 0x1113c0, 0x0 },
> +	{ 0x2113c0, 0x0 },
> +	{ 0x114c0, 0x0 },
> +	{ 0x1114c0, 0x0 },
> +	{ 0x2114c0, 0x0 },
> +	{ 0x115c0, 0x0 },
> +	{ 0x1115c0, 0x0 },
> +	{ 0x2115c0, 0x0 },
> +	{ 0x116c0, 0x0 },
> +	{ 0x1116c0, 0x0 },
> +	{ 0x2116c0, 0x0 },
> +	{ 0x117c0, 0x0 },
> +	{ 0x1117c0, 0x0 },
> +	{ 0x2117c0, 0x0 },
> +	{ 0x118c0, 0x0 },
> +	{ 0x1118c0, 0x0 },
> +	{ 0x2118c0, 0x0 },
> +	{ 0x120c0, 0x0 },
> +	{ 0x1120c0, 0x0 },
> +	{ 0x2120c0, 0x0 },
> +	{ 0x121c0, 0x0 },
> +	{ 0x1121c0, 0x0 },
> +	{ 0x2121c0, 0x0 },
> +	{ 0x122c0, 0x0 },
> +	{ 0x1122c0, 0x0 },
> +	{ 0x2122c0, 0x0 },
> +	{ 0x123c0, 0x0 },
> +	{ 0x1123c0, 0x0 },
> +	{ 0x2123c0, 0x0 },
> +	{ 0x124c0, 0x0 },
> +	{ 0x1124c0, 0x0 },
> +	{ 0x2124c0, 0x0 },
> +	{ 0x125c0, 0x0 },
> +	{ 0x1125c0, 0x0 },
> +	{ 0x2125c0, 0x0 },
> +	{ 0x126c0, 0x0 },
> +	{ 0x1126c0, 0x0 },
> +	{ 0x2126c0, 0x0 },
> +	{ 0x127c0, 0x0 },
> +	{ 0x1127c0, 0x0 },
> +	{ 0x2127c0, 0x0 },
> +	{ 0x128c0, 0x0 },
> +	{ 0x1128c0, 0x0 },
> +	{ 0x2128c0, 0x0 },
> +	{ 0x130c0, 0x0 },
> +	{ 0x1130c0, 0x0 },
> +	{ 0x2130c0, 0x0 },
> +	{ 0x131c0, 0x0 },
> +	{ 0x1131c0, 0x0 },
> +	{ 0x2131c0, 0x0 },
> +	{ 0x132c0, 0x0 },
> +	{ 0x1132c0, 0x0 },
> +	{ 0x2132c0, 0x0 },
> +	{ 0x133c0, 0x0 },
> +	{ 0x1133c0, 0x0 },
> +	{ 0x2133c0, 0x0 },
> +	{ 0x134c0, 0x0 },
> +	{ 0x1134c0, 0x0 },
> +	{ 0x2134c0, 0x0 },
> +	{ 0x135c0, 0x0 },
> +	{ 0x1135c0, 0x0 },
> +	{ 0x2135c0, 0x0 },
> +	{ 0x136c0, 0x0 },
> +	{ 0x1136c0, 0x0 },
> +	{ 0x2136c0, 0x0 },
> +	{ 0x137c0, 0x0 },
> +	{ 0x1137c0, 0x0 },
> +	{ 0x2137c0, 0x0 },
> +	{ 0x138c0, 0x0 },
> +	{ 0x1138c0, 0x0 },
> +	{ 0x2138c0, 0x0 },
> +	{ 0x100c1, 0x0 },
> +	{ 0x1100c1, 0x0 },
> +	{ 0x2100c1, 0x0 },
> +	{ 0x101c1, 0x0 },
> +	{ 0x1101c1, 0x0 },
> +	{ 0x2101c1, 0x0 },
> +	{ 0x102c1, 0x0 },
> +	{ 0x1102c1, 0x0 },
> +	{ 0x2102c1, 0x0 },
> +	{ 0x103c1, 0x0 },
> +	{ 0x1103c1, 0x0 },
> +	{ 0x2103c1, 0x0 },
> +	{ 0x104c1, 0x0 },
> +	{ 0x1104c1, 0x0 },
> +	{ 0x2104c1, 0x0 },
> +	{ 0x105c1, 0x0 },
> +	{ 0x1105c1, 0x0 },
> +	{ 0x2105c1, 0x0 },
> +	{ 0x106c1, 0x0 },
> +	{ 0x1106c1, 0x0 },
> +	{ 0x2106c1, 0x0 },
> +	{ 0x107c1, 0x0 },
> +	{ 0x1107c1, 0x0 },
> +	{ 0x2107c1, 0x0 },
> +	{ 0x108c1, 0x0 },
> +	{ 0x1108c1, 0x0 },
> +	{ 0x2108c1, 0x0 },
> +	{ 0x110c1, 0x0 },
> +	{ 0x1110c1, 0x0 },
> +	{ 0x2110c1, 0x0 },
> +	{ 0x111c1, 0x0 },
> +	{ 0x1111c1, 0x0 },
> +	{ 0x2111c1, 0x0 },
> +	{ 0x112c1, 0x0 },
> +	{ 0x1112c1, 0x0 },
> +	{ 0x2112c1, 0x0 },
> +	{ 0x113c1, 0x0 },
> +	{ 0x1113c1, 0x0 },
> +	{ 0x2113c1, 0x0 },
> +	{ 0x114c1, 0x0 },
> +	{ 0x1114c1, 0x0 },
> +	{ 0x2114c1, 0x0 },
> +	{ 0x115c1, 0x0 },
> +	{ 0x1115c1, 0x0 },
> +	{ 0x2115c1, 0x0 },
> +	{ 0x116c1, 0x0 },
> +	{ 0x1116c1, 0x0 },
> +	{ 0x2116c1, 0x0 },
> +	{ 0x117c1, 0x0 },
> +	{ 0x1117c1, 0x0 },
> +	{ 0x2117c1, 0x0 },
> +	{ 0x118c1, 0x0 },
> +	{ 0x1118c1, 0x0 },
> +	{ 0x2118c1, 0x0 },
> +	{ 0x120c1, 0x0 },
> +	{ 0x1120c1, 0x0 },
> +	{ 0x2120c1, 0x0 },
> +	{ 0x121c1, 0x0 },
> +	{ 0x1121c1, 0x0 },
> +	{ 0x2121c1, 0x0 },
> +	{ 0x122c1, 0x0 },
> +	{ 0x1122c1, 0x0 },
> +	{ 0x2122c1, 0x0 },
> +	{ 0x123c1, 0x0 },
> +	{ 0x1123c1, 0x0 },
> +	{ 0x2123c1, 0x0 },
> +	{ 0x124c1, 0x0 },
> +	{ 0x1124c1, 0x0 },
> +	{ 0x2124c1, 0x0 },
> +	{ 0x125c1, 0x0 },
> +	{ 0x1125c1, 0x0 },
> +	{ 0x2125c1, 0x0 },
> +	{ 0x126c1, 0x0 },
> +	{ 0x1126c1, 0x0 },
> +	{ 0x2126c1, 0x0 },
> +	{ 0x127c1, 0x0 },
> +	{ 0x1127c1, 0x0 },
> +	{ 0x2127c1, 0x0 },
> +	{ 0x128c1, 0x0 },
> +	{ 0x1128c1, 0x0 },
> +	{ 0x2128c1, 0x0 },
> +	{ 0x130c1, 0x0 },
> +	{ 0x1130c1, 0x0 },
> +	{ 0x2130c1, 0x0 },
> +	{ 0x131c1, 0x0 },
> +	{ 0x1131c1, 0x0 },
> +	{ 0x2131c1, 0x0 },
> +	{ 0x132c1, 0x0 },
> +	{ 0x1132c1, 0x0 },
> +	{ 0x2132c1, 0x0 },
> +	{ 0x133c1, 0x0 },
> +	{ 0x1133c1, 0x0 },
> +	{ 0x2133c1, 0x0 },
> +	{ 0x134c1, 0x0 },
> +	{ 0x1134c1, 0x0 },
> +	{ 0x2134c1, 0x0 },
> +	{ 0x135c1, 0x0 },
> +	{ 0x1135c1, 0x0 },
> +	{ 0x2135c1, 0x0 },
> +	{ 0x136c1, 0x0 },
> +	{ 0x1136c1, 0x0 },
> +	{ 0x2136c1, 0x0 },
> +	{ 0x137c1, 0x0 },
> +	{ 0x1137c1, 0x0 },
> +	{ 0x2137c1, 0x0 },
> +	{ 0x138c1, 0x0 },
> +	{ 0x1138c1, 0x0 },
> +	{ 0x2138c1, 0x0 },
> +	{ 0x10020, 0x0 },
> +	{ 0x110020, 0x0 },
> +	{ 0x210020, 0x0 },
> +	{ 0x11020, 0x0 },
> +	{ 0x111020, 0x0 },
> +	{ 0x211020, 0x0 },
> +	{ 0x12020, 0x0 },
> +	{ 0x112020, 0x0 },
> +	{ 0x212020, 0x0 },
> +	{ 0x13020, 0x0 },
> +	{ 0x113020, 0x0 },
> +	{ 0x213020, 0x0 },
> +	{ 0x20072, 0x0 },
> +	{ 0x20073, 0x0 },
> +	{ 0x20074, 0x0 },
> +	{ 0x100aa, 0x0 },
> +	{ 0x110aa, 0x0 },
> +	{ 0x120aa, 0x0 },
> +	{ 0x130aa, 0x0 },
> +	{ 0x20010, 0x0 },
> +	{ 0x120010, 0x0 },
> +	{ 0x220010, 0x0 },
> +	{ 0x20011, 0x0 },
> +	{ 0x120011, 0x0 },
> +	{ 0x220011, 0x0 },
> +	{ 0x100ae, 0x0 },
> +	{ 0x1100ae, 0x0 },
> +	{ 0x2100ae, 0x0 },
> +	{ 0x100af, 0x0 },
> +	{ 0x1100af, 0x0 },
> +	{ 0x2100af, 0x0 },
> +	{ 0x110ae, 0x0 },
> +	{ 0x1110ae, 0x0 },
> +	{ 0x2110ae, 0x0 },
> +	{ 0x110af, 0x0 },
> +	{ 0x1110af, 0x0 },
> +	{ 0x2110af, 0x0 },
> +	{ 0x120ae, 0x0 },
> +	{ 0x1120ae, 0x0 },
> +	{ 0x2120ae, 0x0 },
> +	{ 0x120af, 0x0 },
> +	{ 0x1120af, 0x0 },
> +	{ 0x2120af, 0x0 },
> +	{ 0x130ae, 0x0 },
> +	{ 0x1130ae, 0x0 },
> +	{ 0x2130ae, 0x0 },
> +	{ 0x130af, 0x0 },
> +	{ 0x1130af, 0x0 },
> +	{ 0x2130af, 0x0 },
> +	{ 0x20020, 0x0 },
> +	{ 0x120020, 0x0 },
> +	{ 0x220020, 0x0 },
> +	{ 0x100a0, 0x0 },
> +	{ 0x100a1, 0x0 },
> +	{ 0x100a2, 0x0 },
> +	{ 0x100a3, 0x0 },
> +	{ 0x100a4, 0x0 },
> +	{ 0x100a5, 0x0 },
> +	{ 0x100a6, 0x0 },
> +	{ 0x100a7, 0x0 },
> +	{ 0x110a0, 0x0 },
> +	{ 0x110a1, 0x0 },
> +	{ 0x110a2, 0x0 },
> +	{ 0x110a3, 0x0 },
> +	{ 0x110a4, 0x0 },
> +	{ 0x110a5, 0x0 },
> +	{ 0x110a6, 0x0 },
> +	{ 0x110a7, 0x0 },
> +	{ 0x120a0, 0x0 },
> +	{ 0x120a1, 0x0 },
> +	{ 0x120a2, 0x0 },
> +	{ 0x120a3, 0x0 },
> +	{ 0x120a4, 0x0 },
> +	{ 0x120a5, 0x0 },
> +	{ 0x120a6, 0x0 },
> +	{ 0x120a7, 0x0 },
> +	{ 0x130a0, 0x0 },
> +	{ 0x130a1, 0x0 },
> +	{ 0x130a2, 0x0 },
> +	{ 0x130a3, 0x0 },
> +	{ 0x130a4, 0x0 },
> +	{ 0x130a5, 0x0 },
> +	{ 0x130a6, 0x0 },
> +	{ 0x130a7, 0x0 },
> +	{ 0x2007c, 0x0 },
> +	{ 0x12007c, 0x0 },
> +	{ 0x22007c, 0x0 },
> +	{ 0x2007d, 0x0 },
> +	{ 0x12007d, 0x0 },
> +	{ 0x22007d, 0x0 },
> +	{ 0x400fd, 0x0 },
> +	{ 0x400c0, 0x0 },
> +	{ 0x90201, 0x0 },
> +	{ 0x190201, 0x0 },
> +	{ 0x290201, 0x0 },
> +	{ 0x90202, 0x0 },
> +	{ 0x190202, 0x0 },
> +	{ 0x290202, 0x0 },
> +	{ 0x90203, 0x0 },
> +	{ 0x190203, 0x0 },
> +	{ 0x290203, 0x0 },
> +	{ 0x90204, 0x0 },
> +	{ 0x190204, 0x0 },
> +	{ 0x290204, 0x0 },
> +	{ 0x90205, 0x0 },
> +	{ 0x190205, 0x0 },
> +	{ 0x290205, 0x0 },
> +	{ 0x90206, 0x0 },
> +	{ 0x190206, 0x0 },
> +	{ 0x290206, 0x0 },
> +	{ 0x90207, 0x0 },
> +	{ 0x190207, 0x0 },
> +	{ 0x290207, 0x0 },
> +	{ 0x90208, 0x0 },
> +	{ 0x190208, 0x0 },
> +	{ 0x290208, 0x0 },
> +	{ 0x10062, 0x0 },
> +	{ 0x10162, 0x0 },
> +	{ 0x10262, 0x0 },
> +	{ 0x10362, 0x0 },
> +	{ 0x10462, 0x0 },
> +	{ 0x10562, 0x0 },
> +	{ 0x10662, 0x0 },
> +	{ 0x10762, 0x0 },
> +	{ 0x10862, 0x0 },
> +	{ 0x11062, 0x0 },
> +	{ 0x11162, 0x0 },
> +	{ 0x11262, 0x0 },
> +	{ 0x11362, 0x0 },
> +	{ 0x11462, 0x0 },
> +	{ 0x11562, 0x0 },
> +	{ 0x11662, 0x0 },
> +	{ 0x11762, 0x0 },
> +	{ 0x11862, 0x0 },
> +	{ 0x12062, 0x0 },
> +	{ 0x12162, 0x0 },
> +	{ 0x12262, 0x0 },
> +	{ 0x12362, 0x0 },
> +	{ 0x12462, 0x0 },
> +	{ 0x12562, 0x0 },
> +	{ 0x12662, 0x0 },
> +	{ 0x12762, 0x0 },
> +	{ 0x12862, 0x0 },
> +	{ 0x13062, 0x0 },
> +	{ 0x13162, 0x0 },
> +	{ 0x13262, 0x0 },
> +	{ 0x13362, 0x0 },
> +	{ 0x13462, 0x0 },
> +	{ 0x13562, 0x0 },
> +	{ 0x13662, 0x0 },
> +	{ 0x13762, 0x0 },
> +	{ 0x13862, 0x0 },
> +	{ 0x20077, 0x0 },
> +	{ 0x10001, 0x0 },
> +	{ 0x11001, 0x0 },
> +	{ 0x12001, 0x0 },
> +	{ 0x13001, 0x0 },
> +	{ 0x10040, 0x0 },
> +	{ 0x10140, 0x0 },
> +	{ 0x10240, 0x0 },
> +	{ 0x10340, 0x0 },
> +	{ 0x10440, 0x0 },
> +	{ 0x10540, 0x0 },
> +	{ 0x10640, 0x0 },
> +	{ 0x10740, 0x0 },
> +	{ 0x10840, 0x0 },
> +	{ 0x10030, 0x0 },
> +	{ 0x10130, 0x0 },
> +	{ 0x10230, 0x0 },
> +	{ 0x10330, 0x0 },
> +	{ 0x10430, 0x0 },
> +	{ 0x10530, 0x0 },
> +	{ 0x10630, 0x0 },
> +	{ 0x10730, 0x0 },
> +	{ 0x10830, 0x0 },
> +	{ 0x11040, 0x0 },
> +	{ 0x11140, 0x0 },
> +	{ 0x11240, 0x0 },
> +	{ 0x11340, 0x0 },
> +	{ 0x11440, 0x0 },
> +	{ 0x11540, 0x0 },
> +	{ 0x11640, 0x0 },
> +	{ 0x11740, 0x0 },
> +	{ 0x11840, 0x0 },
> +	{ 0x11030, 0x0 },
> +	{ 0x11130, 0x0 },
> +	{ 0x11230, 0x0 },
> +	{ 0x11330, 0x0 },
> +	{ 0x11430, 0x0 },
> +	{ 0x11530, 0x0 },
> +	{ 0x11630, 0x0 },
> +	{ 0x11730, 0x0 },
> +	{ 0x11830, 0x0 },
> +	{ 0x12040, 0x0 },
> +	{ 0x12140, 0x0 },
> +	{ 0x12240, 0x0 },
> +	{ 0x12340, 0x0 },
> +	{ 0x12440, 0x0 },
> +	{ 0x12540, 0x0 },
> +	{ 0x12640, 0x0 },
> +	{ 0x12740, 0x0 },
> +	{ 0x12840, 0x0 },
> +	{ 0x12030, 0x0 },
> +	{ 0x12130, 0x0 },
> +	{ 0x12230, 0x0 },
> +	{ 0x12330, 0x0 },
> +	{ 0x12430, 0x0 },
> +	{ 0x12530, 0x0 },
> +	{ 0x12630, 0x0 },
> +	{ 0x12730, 0x0 },
> +	{ 0x12830, 0x0 },
> +	{ 0x13040, 0x0 },
> +	{ 0x13140, 0x0 },
> +	{ 0x13240, 0x0 },
> +	{ 0x13340, 0x0 },
> +	{ 0x13440, 0x0 },
> +	{ 0x13540, 0x0 },
> +	{ 0x13640, 0x0 },
> +	{ 0x13740, 0x0 },
> +	{ 0x13840, 0x0 },
> +	{ 0x13030, 0x0 },
> +	{ 0x13130, 0x0 },
> +	{ 0x13230, 0x0 },
> +	{ 0x13330, 0x0 },
> +	{ 0x13430, 0x0 },
> +	{ 0x13530, 0x0 },
> +	{ 0x13630, 0x0 },
> +	{ 0x13730, 0x0 },
> +	{ 0x13830, 0x0 },
> +};
> +
> +/* P0 message block paremeter for training firmware */
> +struct dram_cfg_param ddr_fsp0_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54003, 0xc80 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x131f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x310 },
> +	{ 0x54019, 0x2dd4 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x2dd4 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x3 },
> +	{ 0x54032, 0xd400 },
> +	{ 0x54033, 0x312d },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0xd400 },
> +	{ 0x54039, 0x312d },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P1 message block paremeter for training firmware */
> +struct dram_cfg_param ddr_fsp1_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54002, 0x101 },
> +	{ 0x54003, 0x190 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x121f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x310 },
> +	{ 0x54019, 0x84 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x84 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x3 },
> +	{ 0x54032, 0x8400 },
> +	{ 0x54033, 0x3100 },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0x8400 },
> +	{ 0x54039, 0x3100 },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P2 message block paremeter for training firmware */
> +struct dram_cfg_param ddr_fsp2_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54002, 0x102 },
> +	{ 0x54003, 0x64 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x121f },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x54012, 0x310 },
> +	{ 0x54019, 0x84 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x84 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x3 },
> +	{ 0x54032, 0x8400 },
> +	{ 0x54033, 0x3100 },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0x8400 },
> +	{ 0x54039, 0x3100 },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* P0 2D message block paremeter for training firmware */
> +struct dram_cfg_param ddr_fsp0_2d_cfg[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x54003, 0xc80 },
> +	{ 0x54004, 0x2 },
> +	{ 0x54005, 0x2228 },
> +	{ 0x54006, 0x11 },
> +	{ 0x54008, 0x61 },
> +	{ 0x54009, 0xc8 },
> +	{ 0x5400b, 0x2 },
> +	{ 0x5400d, 0x100 },
> +	{ 0x5400f, 0x100 },
> +	{ 0x54010, 0x1f7f },
> +	{ 0x54012, 0x310 },
> +	{ 0x54019, 0x2dd4 },
> +	{ 0x5401a, 0x31 },
> +	{ 0x5401b, 0x4a66 },
> +	{ 0x5401c, 0x4a08 },
> +	{ 0x5401e, 0x16 },
> +	{ 0x5401f, 0x2dd4 },
> +	{ 0x54020, 0x31 },
> +	{ 0x54021, 0x4a66 },
> +	{ 0x54022, 0x4a08 },
> +	{ 0x54024, 0x16 },
> +	{ 0x5402b, 0x1000 },
> +	{ 0x5402c, 0x3 },
> +	{ 0x54032, 0xd400 },
> +	{ 0x54033, 0x312d },
> +	{ 0x54034, 0x6600 },
> +	{ 0x54035, 0x84a },
> +	{ 0x54036, 0x4a },
> +	{ 0x54037, 0x1600 },
> +	{ 0x54038, 0xd400 },
> +	{ 0x54039, 0x312d },
> +	{ 0x5403a, 0x6600 },
> +	{ 0x5403b, 0x84a },
> +	{ 0x5403c, 0x4a },
> +	{ 0x5403d, 0x1600 },
> +	{ 0xd0000, 0x1 },
> +};
> +
> +/* DRAM PHY init engine image */
> +struct dram_cfg_param ddr_phy_pie[] = {
> +	{ 0xd0000, 0x0 },
> +	{ 0x90000, 0x10 },
> +	{ 0x90001, 0x400 },
> +	{ 0x90002, 0x10e },
> +	{ 0x90003, 0x0 },
> +	{ 0x90004, 0x0 },
> +	{ 0x90005, 0x8 },
> +	{ 0x90029, 0xb },
> +	{ 0x9002a, 0x480 },
> +	{ 0x9002b, 0x109 },
> +	{ 0x9002c, 0x8 },
> +	{ 0x9002d, 0x448 },
> +	{ 0x9002e, 0x139 },
> +	{ 0x9002f, 0x8 },
> +	{ 0x90030, 0x478 },
> +	{ 0x90031, 0x109 },
> +	{ 0x90032, 0x0 },
> +	{ 0x90033, 0xe8 },
> +	{ 0x90034, 0x109 },
> +	{ 0x90035, 0x2 },
> +	{ 0x90036, 0x10 },
> +	{ 0x90037, 0x139 },
> +	{ 0x90038, 0xf },
> +	{ 0x90039, 0x7c0 },
> +	{ 0x9003a, 0x139 },
> +	{ 0x9003b, 0x44 },
> +	{ 0x9003c, 0x630 },
> +	{ 0x9003d, 0x159 },
> +	{ 0x9003e, 0x14f },
> +	{ 0x9003f, 0x630 },
> +	{ 0x90040, 0x159 },
> +	{ 0x90041, 0x47 },
> +	{ 0x90042, 0x630 },
> +	{ 0x90043, 0x149 },
> +	{ 0x90044, 0x4f },
> +	{ 0x90045, 0x630 },
> +	{ 0x90046, 0x179 },
> +	{ 0x90047, 0x8 },
> +	{ 0x90048, 0xe0 },
> +	{ 0x90049, 0x109 },
> +	{ 0x9004a, 0x0 },
> +	{ 0x9004b, 0x7c8 },
> +	{ 0x9004c, 0x109 },
> +	{ 0x9004d, 0x0 },
> +	{ 0x9004e, 0x1 },
> +	{ 0x9004f, 0x8 },
> +	{ 0x90050, 0x0 },
> +	{ 0x90051, 0x45a },
> +	{ 0x90052, 0x9 },
> +	{ 0x90053, 0x0 },
> +	{ 0x90054, 0x448 },
> +	{ 0x90055, 0x109 },
> +	{ 0x90056, 0x40 },
> +	{ 0x90057, 0x630 },
> +	{ 0x90058, 0x179 },
> +	{ 0x90059, 0x1 },
> +	{ 0x9005a, 0x618 },
> +	{ 0x9005b, 0x109 },
> +	{ 0x9005c, 0x40c0 },
> +	{ 0x9005d, 0x630 },
> +	{ 0x9005e, 0x149 },
> +	{ 0x9005f, 0x8 },
> +	{ 0x90060, 0x4 },
> +	{ 0x90061, 0x48 },
> +	{ 0x90062, 0x4040 },
> +	{ 0x90063, 0x630 },
> +	{ 0x90064, 0x149 },
> +	{ 0x90065, 0x0 },
> +	{ 0x90066, 0x4 },
> +	{ 0x90067, 0x48 },
> +	{ 0x90068, 0x40 },
> +	{ 0x90069, 0x630 },
> +	{ 0x9006a, 0x149 },
> +	{ 0x9006b, 0x10 },
> +	{ 0x9006c, 0x4 },
> +	{ 0x9006d, 0x18 },
> +	{ 0x9006e, 0x0 },
> +	{ 0x9006f, 0x4 },
> +	{ 0x90070, 0x78 },
> +	{ 0x90071, 0x549 },
> +	{ 0x90072, 0x630 },
> +	{ 0x90073, 0x159 },
> +	{ 0x90074, 0xd49 },
> +	{ 0x90075, 0x630 },
> +	{ 0x90076, 0x159 },
> +	{ 0x90077, 0x94a },
> +	{ 0x90078, 0x630 },
> +	{ 0x90079, 0x159 },
> +	{ 0x9007a, 0x441 },
> +	{ 0x9007b, 0x630 },
> +	{ 0x9007c, 0x149 },
> +	{ 0x9007d, 0x42 },
> +	{ 0x9007e, 0x630 },
> +	{ 0x9007f, 0x149 },
> +	{ 0x90080, 0x1 },
> +	{ 0x90081, 0x630 },
> +	{ 0x90082, 0x149 },
> +	{ 0x90083, 0x0 },
> +	{ 0x90084, 0xe0 },
> +	{ 0x90085, 0x109 },
> +	{ 0x90086, 0xa },
> +	{ 0x90087, 0x10 },
> +	{ 0x90088, 0x109 },
> +	{ 0x90089, 0x9 },
> +	{ 0x9008a, 0x3c0 },
> +	{ 0x9008b, 0x149 },
> +	{ 0x9008c, 0x9 },
> +	{ 0x9008d, 0x3c0 },
> +	{ 0x9008e, 0x159 },
> +	{ 0x9008f, 0x18 },
> +	{ 0x90090, 0x10 },
> +	{ 0x90091, 0x109 },
> +	{ 0x90092, 0x0 },
> +	{ 0x90093, 0x3c0 },
> +	{ 0x90094, 0x109 },
> +	{ 0x90095, 0x18 },
> +	{ 0x90096, 0x4 },
> +	{ 0x90097, 0x48 },
> +	{ 0x90098, 0x18 },
> +	{ 0x90099, 0x4 },
> +	{ 0x9009a, 0x58 },
> +	{ 0x9009b, 0xa },
> +	{ 0x9009c, 0x10 },
> +	{ 0x9009d, 0x109 },
> +	{ 0x9009e, 0x2 },
> +	{ 0x9009f, 0x10 },
> +	{ 0x900a0, 0x109 },
> +	{ 0x900a1, 0x5 },
> +	{ 0x900a2, 0x7c0 },
> +	{ 0x900a3, 0x109 },
> +	{ 0x900a4, 0x10 },
> +	{ 0x900a5, 0x10 },
> +	{ 0x900a6, 0x109 },
> +	{ 0x40000, 0x811 },
> +	{ 0x40020, 0x880 },
> +	{ 0x40040, 0x0 },
> +	{ 0x40060, 0x0 },
> +	{ 0x40001, 0x4008 },
> +	{ 0x40021, 0x83 },
> +	{ 0x40041, 0x4f },
> +	{ 0x40061, 0x0 },
> +	{ 0x40002, 0x4040 },
> +	{ 0x40022, 0x83 },
> +	{ 0x40042, 0x51 },
> +	{ 0x40062, 0x0 },
> +	{ 0x40003, 0x811 },
> +	{ 0x40023, 0x880 },
> +	{ 0x40043, 0x0 },
> +	{ 0x40063, 0x0 },
> +	{ 0x40004, 0x720 },
> +	{ 0x40024, 0xf },
> +	{ 0x40044, 0x1740 },
> +	{ 0x40064, 0x0 },
> +	{ 0x40005, 0x16 },
> +	{ 0x40025, 0x83 },
> +	{ 0x40045, 0x4b },
> +	{ 0x40065, 0x0 },
> +	{ 0x40006, 0x716 },
> +	{ 0x40026, 0xf },
> +	{ 0x40046, 0x2001 },
> +	{ 0x40066, 0x0 },
> +	{ 0x40007, 0x716 },
> +	{ 0x40027, 0xf },
> +	{ 0x40047, 0x2800 },
> +	{ 0x40067, 0x0 },
> +	{ 0x40008, 0x716 },
> +	{ 0x40028, 0xf },
> +	{ 0x40048, 0xf00 },
> +	{ 0x40068, 0x0 },
> +	{ 0x40009, 0x720 },
> +	{ 0x40029, 0xf },
> +	{ 0x40049, 0x1400 },
> +	{ 0x40069, 0x0 },
> +	{ 0x4000a, 0xe08 },
> +	{ 0x4002a, 0xc15 },
> +	{ 0x4004a, 0x0 },
> +	{ 0x4006a, 0x0 },
> +	{ 0x4000b, 0x623 },
> +	{ 0x4002b, 0x15 },
> +	{ 0x4004b, 0x0 },
> +	{ 0x4006b, 0x0 },
> +	{ 0x4000c, 0x4028 },
> +	{ 0x4002c, 0x80 },
> +	{ 0x4004c, 0x0 },
> +	{ 0x4006c, 0x0 },
> +	{ 0x4000d, 0xe08 },
> +	{ 0x4002d, 0xc1a },
> +	{ 0x4004d, 0x0 },
> +	{ 0x4006d, 0x0 },
> +	{ 0x4000e, 0x623 },
> +	{ 0x4002e, 0x1a },
> +	{ 0x4004e, 0x0 },
> +	{ 0x4006e, 0x0 },
> +	{ 0x4000f, 0x4040 },
> +	{ 0x4002f, 0x80 },
> +	{ 0x4004f, 0x0 },
> +	{ 0x4006f, 0x0 },
> +	{ 0x40010, 0x2604 },
> +	{ 0x40030, 0x15 },
> +	{ 0x40050, 0x0 },
> +	{ 0x40070, 0x0 },
> +	{ 0x40011, 0x708 },
> +	{ 0x40031, 0x5 },
> +	{ 0x40051, 0x0 },
> +	{ 0x40071, 0x2002 },
> +	{ 0x40012, 0x8 },
> +	{ 0x40032, 0x80 },
> +	{ 0x40052, 0x0 },
> +	{ 0x40072, 0x0 },
> +	{ 0x40013, 0x2604 },
> +	{ 0x40033, 0x1a },
> +	{ 0x40053, 0x0 },
> +	{ 0x40073, 0x0 },
> +	{ 0x40014, 0x708 },
> +	{ 0x40034, 0xa },
> +	{ 0x40054, 0x0 },
> +	{ 0x40074, 0x2002 },
> +	{ 0x40015, 0x4040 },
> +	{ 0x40035, 0x80 },
> +	{ 0x40055, 0x0 },
> +	{ 0x40075, 0x0 },
> +	{ 0x40016, 0x60a },
> +	{ 0x40036, 0x15 },
> +	{ 0x40056, 0x1200 },
> +	{ 0x40076, 0x0 },
> +	{ 0x40017, 0x61a },
> +	{ 0x40037, 0x15 },
> +	{ 0x40057, 0x1300 },
> +	{ 0x40077, 0x0 },
> +	{ 0x40018, 0x60a },
> +	{ 0x40038, 0x1a },
> +	{ 0x40058, 0x1200 },
> +	{ 0x40078, 0x0 },
> +	{ 0x40019, 0x642 },
> +	{ 0x40039, 0x1a },
> +	{ 0x40059, 0x1300 },
> +	{ 0x40079, 0x0 },
> +	{ 0x4001a, 0x4808 },
> +	{ 0x4003a, 0x880 },
> +	{ 0x4005a, 0x0 },
> +	{ 0x4007a, 0x0 },
> +	{ 0x900a7, 0x0 },
> +	{ 0x900a8, 0x790 },
> +	{ 0x900a9, 0x11a },
> +	{ 0x900aa, 0x8 },
> +	{ 0x900ab, 0x7aa },
> +	{ 0x900ac, 0x2a },
> +	{ 0x900ad, 0x10 },
> +	{ 0x900ae, 0x7b2 },
> +	{ 0x900af, 0x2a },
> +	{ 0x900b0, 0x0 },
> +	{ 0x900b1, 0x7c8 },
> +	{ 0x900b2, 0x109 },
> +	{ 0x900b3, 0x10 },
> +	{ 0x900b4, 0x2a8 },
> +	{ 0x900b5, 0x129 },
> +	{ 0x900b6, 0x8 },
> +	{ 0x900b7, 0x370 },
> +	{ 0x900b8, 0x129 },
> +	{ 0x900b9, 0xa },
> +	{ 0x900ba, 0x3c8 },
> +	{ 0x900bb, 0x1a9 },
> +	{ 0x900bc, 0xc },
> +	{ 0x900bd, 0x408 },
> +	{ 0x900be, 0x199 },
> +	{ 0x900bf, 0x14 },
> +	{ 0x900c0, 0x790 },
> +	{ 0x900c1, 0x11a },
> +	{ 0x900c2, 0x8 },
> +	{ 0x900c3, 0x4 },
> +	{ 0x900c4, 0x18 },
> +	{ 0x900c5, 0xe },
> +	{ 0x900c6, 0x408 },
> +	{ 0x900c7, 0x199 },
> +	{ 0x900c8, 0x8 },
> +	{ 0x900c9, 0x8568 },
> +	{ 0x900ca, 0x108 },
> +	{ 0x900cb, 0x18 },
> +	{ 0x900cc, 0x790 },
> +	{ 0x900cd, 0x16a },
> +	{ 0x900ce, 0x8 },
> +	{ 0x900cf, 0x1d8 },
> +	{ 0x900d0, 0x169 },
> +	{ 0x900d1, 0x10 },
> +	{ 0x900d2, 0x8558 },
> +	{ 0x900d3, 0x168 },
> +	{ 0x900d4, 0x70 },
> +	{ 0x900d5, 0x788 },
> +	{ 0x900d6, 0x16a },
> +	{ 0x900d7, 0x1ff8 },
> +	{ 0x900d8, 0x85a8 },
> +	{ 0x900d9, 0x1e8 },
> +	{ 0x900da, 0x50 },
> +	{ 0x900db, 0x798 },
> +	{ 0x900dc, 0x16a },
> +	{ 0x900dd, 0x60 },
> +	{ 0x900de, 0x7a0 },
> +	{ 0x900df, 0x16a },
> +	{ 0x900e0, 0x8 },
> +	{ 0x900e1, 0x8310 },
> +	{ 0x900e2, 0x168 },
> +	{ 0x900e3, 0x8 },
> +	{ 0x900e4, 0xa310 },
> +	{ 0x900e5, 0x168 },
> +	{ 0x900e6, 0xa },
> +	{ 0x900e7, 0x408 },
> +	{ 0x900e8, 0x169 },
> +	{ 0x900e9, 0x6e },
> +	{ 0x900ea, 0x0 },
> +	{ 0x900eb, 0x68 },
> +	{ 0x900ec, 0x0 },
> +	{ 0x900ed, 0x408 },
> +	{ 0x900ee, 0x169 },
> +	{ 0x900ef, 0x0 },
> +	{ 0x900f0, 0x8310 },
> +	{ 0x900f1, 0x168 },
> +	{ 0x900f2, 0x0 },
> +	{ 0x900f3, 0xa310 },
> +	{ 0x900f4, 0x168 },
> +	{ 0x900f5, 0x1ff8 },
> +	{ 0x900f6, 0x85a8 },
> +	{ 0x900f7, 0x1e8 },
> +	{ 0x900f8, 0x68 },
> +	{ 0x900f9, 0x798 },
> +	{ 0x900fa, 0x16a },
> +	{ 0x900fb, 0x78 },
> +	{ 0x900fc, 0x7a0 },
> +	{ 0x900fd, 0x16a },
> +	{ 0x900fe, 0x68 },
> +	{ 0x900ff, 0x790 },
> +	{ 0x90100, 0x16a },
> +	{ 0x90101, 0x8 },
> +	{ 0x90102, 0x8b10 },
> +	{ 0x90103, 0x168 },
> +	{ 0x90104, 0x8 },
> +	{ 0x90105, 0xab10 },
> +	{ 0x90106, 0x168 },
> +	{ 0x90107, 0xa },
> +	{ 0x90108, 0x408 },
> +	{ 0x90109, 0x169 },
> +	{ 0x9010a, 0x58 },
> +	{ 0x9010b, 0x0 },
> +	{ 0x9010c, 0x68 },
> +	{ 0x9010d, 0x0 },
> +	{ 0x9010e, 0x408 },
> +	{ 0x9010f, 0x169 },
> +	{ 0x90110, 0x0 },
> +	{ 0x90111, 0x8b10 },
> +	{ 0x90112, 0x168 },
> +	{ 0x90113, 0x0 },
> +	{ 0x90114, 0xab10 },
> +	{ 0x90115, 0x168 },
> +	{ 0x90116, 0x0 },
> +	{ 0x90117, 0x1d8 },
> +	{ 0x90118, 0x169 },
> +	{ 0x90119, 0x80 },
> +	{ 0x9011a, 0x790 },
> +	{ 0x9011b, 0x16a },
> +	{ 0x9011c, 0x18 },
> +	{ 0x9011d, 0x7aa },
> +	{ 0x9011e, 0x6a },
> +	{ 0x9011f, 0xa },
> +	{ 0x90120, 0x0 },
> +	{ 0x90121, 0x1e9 },
> +	{ 0x90122, 0x8 },
> +	{ 0x90123, 0x8080 },
> +	{ 0x90124, 0x108 },
> +	{ 0x90125, 0xf },
> +	{ 0x90126, 0x408 },
> +	{ 0x90127, 0x169 },
> +	{ 0x90128, 0xc },
> +	{ 0x90129, 0x0 },
> +	{ 0x9012a, 0x68 },
> +	{ 0x9012b, 0x9 },
> +	{ 0x9012c, 0x0 },
> +	{ 0x9012d, 0x1a9 },
> +	{ 0x9012e, 0x0 },
> +	{ 0x9012f, 0x408 },
> +	{ 0x90130, 0x169 },
> +	{ 0x90131, 0x0 },
> +	{ 0x90132, 0x8080 },
> +	{ 0x90133, 0x108 },
> +	{ 0x90134, 0x8 },
> +	{ 0x90135, 0x7aa },
> +	{ 0x90136, 0x6a },
> +	{ 0x90137, 0x0 },
> +	{ 0x90138, 0x8568 },
> +	{ 0x90139, 0x108 },
> +	{ 0x9013a, 0xb7 },
> +	{ 0x9013b, 0x790 },
> +	{ 0x9013c, 0x16a },
> +	{ 0x9013d, 0x1f },
> +	{ 0x9013e, 0x0 },
> +	{ 0x9013f, 0x68 },
> +	{ 0x90140, 0x8 },
> +	{ 0x90141, 0x8558 },
> +	{ 0x90142, 0x168 },
> +	{ 0x90143, 0xf },
> +	{ 0x90144, 0x408 },
> +	{ 0x90145, 0x169 },
> +	{ 0x90146, 0xc },
> +	{ 0x90147, 0x0 },
> +	{ 0x90148, 0x68 },
> +	{ 0x90149, 0x0 },
> +	{ 0x9014a, 0x408 },
> +	{ 0x9014b, 0x169 },
> +	{ 0x9014c, 0x0 },
> +	{ 0x9014d, 0x8558 },
> +	{ 0x9014e, 0x168 },
> +	{ 0x9014f, 0x8 },
> +	{ 0x90150, 0x3c8 },
> +	{ 0x90151, 0x1a9 },
> +	{ 0x90152, 0x3 },
> +	{ 0x90153, 0x370 },
> +	{ 0x90154, 0x129 },
> +	{ 0x90155, 0x20 },
> +	{ 0x90156, 0x2aa },
> +	{ 0x90157, 0x9 },
> +	{ 0x90158, 0x0 },
> +	{ 0x90159, 0x400 },
> +	{ 0x9015a, 0x10e },
> +	{ 0x9015b, 0x8 },
> +	{ 0x9015c, 0xe8 },
> +	{ 0x9015d, 0x109 },
> +	{ 0x9015e, 0x0 },
> +	{ 0x9015f, 0x8140 },
> +	{ 0x90160, 0x10c },
> +	{ 0x90161, 0x10 },
> +	{ 0x90162, 0x8138 },
> +	{ 0x90163, 0x10c },
> +	{ 0x90164, 0x8 },
> +	{ 0x90165, 0x7c8 },
> +	{ 0x90166, 0x101 },
> +	{ 0x90167, 0x8 },
> +	{ 0x90168, 0x0 },
> +	{ 0x90169, 0x8 },
> +	{ 0x9016a, 0x8 },
> +	{ 0x9016b, 0x448 },
> +	{ 0x9016c, 0x109 },
> +	{ 0x9016d, 0xf },
> +	{ 0x9016e, 0x7c0 },
> +	{ 0x9016f, 0x109 },
> +	{ 0x90170, 0x0 },
> +	{ 0x90171, 0xe8 },
> +	{ 0x90172, 0x109 },
> +	{ 0x90173, 0x47 },
> +	{ 0x90174, 0x630 },
> +	{ 0x90175, 0x109 },
> +	{ 0x90176, 0x8 },
> +	{ 0x90177, 0x618 },
> +	{ 0x90178, 0x109 },
> +	{ 0x90179, 0x8 },
> +	{ 0x9017a, 0xe0 },
> +	{ 0x9017b, 0x109 },
> +	{ 0x9017c, 0x0 },
> +	{ 0x9017d, 0x7c8 },
> +	{ 0x9017e, 0x109 },
> +	{ 0x9017f, 0x8 },
> +	{ 0x90180, 0x8140 },
> +	{ 0x90181, 0x10c },
> +	{ 0x90182, 0x0 },
> +	{ 0x90183, 0x1 },
> +	{ 0x90184, 0x8 },
> +	{ 0x90185, 0x8 },
> +	{ 0x90186, 0x4 },
> +	{ 0x90187, 0x8 },
> +	{ 0x90188, 0x8 },
> +	{ 0x90189, 0x7c8 },
> +	{ 0x9018a, 0x101 },
> +	{ 0x90006, 0x0 },
> +	{ 0x90007, 0x0 },
> +	{ 0x90008, 0x8 },
> +	{ 0x90009, 0x0 },
> +	{ 0x9000a, 0x0 },
> +	{ 0x9000b, 0x0 },
> +	{ 0xd00e7, 0x400 },
> +	{ 0x90017, 0x0 },
> +	{ 0x9001f, 0x2a },
> +	{ 0x90026, 0x6a },
> +	{ 0x400d0, 0x0 },
> +	{ 0x400d1, 0x101 },
> +	{ 0x400d2, 0x105 },
> +	{ 0x400d3, 0x107 },
> +	{ 0x400d4, 0x10f },
> +	{ 0x400d5, 0x202 },
> +	{ 0x400d6, 0x20a },
> +	{ 0x400d7, 0x20b },
> +	{ 0x2003a, 0x2 },
> +	{ 0x2000b, 0x64 },
> +	{ 0x2000c, 0xc8 },
> +	{ 0x2000d, 0x7d0 },
> +	{ 0x2000e, 0x2c },
> +	{ 0x12000b, 0xc },
> +	{ 0x12000c, 0x19 },
> +	{ 0x12000d, 0xfa },
> +	{ 0x12000e, 0x10 },
> +	{ 0x22000b, 0x3 },
> +	{ 0x22000c, 0x6 },
> +	{ 0x22000d, 0x3e },
> +	{ 0x22000e, 0x10 },
> +	{ 0x9000c, 0x0 },
> +	{ 0x9000d, 0x173 },
> +	{ 0x9000e, 0x60 },
> +	{ 0x9000f, 0x6110 },
> +	{ 0x90010, 0x2152 },
> +	{ 0x90011, 0xdfbd },
> +	{ 0x90012, 0x60 },
> +	{ 0x90013, 0x6152 },
> +	{ 0x20010, 0x5a },
> +	{ 0x20011, 0x3 },
> +	{ 0x120010, 0x5a },
> +	{ 0x120011, 0x3 },
> +	{ 0x220010, 0x5a },
> +	{ 0x220011, 0x3 },
> +	{ 0x40080, 0xe0 },
> +	{ 0x40081, 0x12 },
> +	{ 0x40082, 0xe0 },
> +	{ 0x40083, 0x12 },
> +	{ 0x40084, 0xe0 },
> +	{ 0x40085, 0x12 },
> +	{ 0x140080, 0xe0 },
> +	{ 0x140081, 0x12 },
> +	{ 0x140082, 0xe0 },
> +	{ 0x140083, 0x12 },
> +	{ 0x140084, 0xe0 },
> +	{ 0x140085, 0x12 },
> +	{ 0x240080, 0xe0 },
> +	{ 0x240081, 0x12 },
> +	{ 0x240082, 0xe0 },
> +	{ 0x240083, 0x12 },
> +	{ 0x240084, 0xe0 },
> +	{ 0x240085, 0x12 },
> +	{ 0x400fd, 0xf },
> +	{ 0x10011, 0x1 },
> +	{ 0x10012, 0x1 },
> +	{ 0x10013, 0x180 },
> +	{ 0x10018, 0x1 },
> +	{ 0x10002, 0x6209 },
> +	{ 0x100b2, 0x1 },
> +	{ 0x101b4, 0x1 },
> +	{ 0x102b4, 0x1 },
> +	{ 0x103b4, 0x1 },
> +	{ 0x104b4, 0x1 },
> +	{ 0x105b4, 0x1 },
> +	{ 0x106b4, 0x1 },
> +	{ 0x107b4, 0x1 },
> +	{ 0x108b4, 0x1 },
> +	{ 0x11011, 0x1 },
> +	{ 0x11012, 0x1 },
> +	{ 0x11013, 0x180 },
> +	{ 0x11018, 0x1 },
> +	{ 0x11002, 0x6209 },
> +	{ 0x110b2, 0x1 },
> +	{ 0x111b4, 0x1 },
> +	{ 0x112b4, 0x1 },
> +	{ 0x113b4, 0x1 },
> +	{ 0x114b4, 0x1 },
> +	{ 0x115b4, 0x1 },
> +	{ 0x116b4, 0x1 },
> +	{ 0x117b4, 0x1 },
> +	{ 0x118b4, 0x1 },
> +	{ 0x12011, 0x1 },
> +	{ 0x12012, 0x1 },
> +	{ 0x12013, 0x180 },
> +	{ 0x12018, 0x1 },
> +	{ 0x12002, 0x6209 },
> +	{ 0x120b2, 0x1 },
> +	{ 0x121b4, 0x1 },
> +	{ 0x122b4, 0x1 },
> +	{ 0x123b4, 0x1 },
> +	{ 0x124b4, 0x1 },
> +	{ 0x125b4, 0x1 },
> +	{ 0x126b4, 0x1 },
> +	{ 0x127b4, 0x1 },
> +	{ 0x128b4, 0x1 },
> +	{ 0x13011, 0x1 },
> +	{ 0x13012, 0x1 },
> +	{ 0x13013, 0x180 },
> +	{ 0x13018, 0x1 },
> +	{ 0x13002, 0x6209 },
> +	{ 0x130b2, 0x1 },
> +	{ 0x131b4, 0x1 },
> +	{ 0x132b4, 0x1 },
> +	{ 0x133b4, 0x1 },
> +	{ 0x134b4, 0x1 },
> +	{ 0x135b4, 0x1 },
> +	{ 0x136b4, 0x1 },
> +	{ 0x137b4, 0x1 },
> +	{ 0x138b4, 0x1 },
> +	{ 0x2003a, 0x2 },
> +	{ 0xc0080, 0x2 },
> +	{ 0xd0000, 0x1 }
> +};
> +
> +struct dram_fsp_msg ddr_dram_fsp_msg[] = {
> +	{
> +		/* P0 3200mts 1D */
> +		.drate = 3200,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp0_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_cfg),
> +	},
> +	{
> +		/* P1 400mts 1D */
> +		.drate = 400,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp1_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp1_cfg),
> +	},
> +	{
> +		/* P2 100mts 1D */
> +		.drate = 100,
> +		.fw_type = FW_1D_IMAGE,
> +		.fsp_cfg = ddr_fsp2_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp2_cfg),
> +	},
> +	{
> +		/* P0 3200mts 2D */
> +		.drate = 3200,
> +		.fw_type = FW_2D_IMAGE,
> +		.fsp_cfg = ddr_fsp0_2d_cfg,
> +		.fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_2d_cfg),
> +	},
> +};
> +
> +/* ddr timing config params */
> +struct dram_timing_info dram_timing_4gb = {
> +	.ddrc_cfg = ddr_ddrc_cfg,
> +	.ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg),
> +	.ddrphy_cfg = ddr_ddrphy_cfg,
> +	.ddrphy_cfg_num = ARRAY_SIZE(ddr_ddrphy_cfg),
> +	.fsp_msg = ddr_dram_fsp_msg,
> +	.fsp_msg_num = ARRAY_SIZE(ddr_dram_fsp_msg),
> +	.ddrphy_trained_csr = ddr_ddrphy_trained_csr,
> +	.ddrphy_trained_csr_num = ARRAY_SIZE(ddr_ddrphy_trained_csr),
> +	.ddrphy_pie = ddr_phy_pie,
> +	.ddrphy_pie_num = ARRAY_SIZE(ddr_phy_pie),
> +	.fsp_table = { 3200, 400, 100, },
> +};
> +
> diff --git a/board/kontron/pitx_imx8m/pitx_imx8m.c b/board/kontron/pitx_imx8m/pitx_imx8m.c
> new file mode 100644
> index 0000000000..b4d35fd2bb
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/pitx_imx8m.c
> @@ -0,0 +1,156 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <common.h>
> +#include <init.h>
> +#include <miiphy.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/imx8mq_pins.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm-generic/gpio.h>
> +#include <asm/mach-imx/gpio.h>
> +#include <asm/mach-imx/iomux-v3.h>
> +#include <linux/delay.h>
> +
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define UART_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_FSEL1)
> +#define WDOG_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
> +
> +static iomux_v3_cfg_t const wdog_pads[] = {
> +	IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const uart_pads[] = {
> +	IMX8MQ_PAD_UART3_RXD__UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
> +	IMX8MQ_PAD_UART3_TXD__UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
> +	IMX8MQ_PAD_ECSPI1_SS0__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
> +	IMX8MQ_PAD_ECSPI1_MISO__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
> +};
> +
> +int board_early_init_f(void)
> +{
> +	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
> +
> +	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
> +	set_wdog_reset(wdog);
> +
> +	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
> +
> +	return 0;
> +}
> +
> +int board_phys_sdram_size(phys_size_t *memsize)
> +{
> +	/*
> +	 * Get real memory size by testing available memory in a
> +	 * given range starting at i.MX8M DRAM1 base address 0x40000000.
> +	*/
> +	*memsize = get_ram_size((long *)0x40000000, 0x100000000ULL);
> +	debug("Memsize: %d MiB\n", (int)(*memsize >> 20));
> +
> +	return 0;
> +}
> +
> +
> +#ifdef CONFIG_FEC_MXC
> +#define FEC_RST_PAD IMX_GPIO_NR(1, 11)
> +static iomux_v3_cfg_t const fec1_rst_pads[] = {
> +	IMX8MQ_PAD_GPIO1_IO11__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
> +};
> +
> +static void setup_iomux_fec(void)
> +{
> +	imx_iomux_v3_setup_multiple_pads(fec1_rst_pads,
> +					 ARRAY_SIZE(fec1_rst_pads));
> +}
> +
> +static int setup_fec(void)
> +{
> +	struct iomuxc_gpr_base_regs *gpr =
> +		(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
> +
> +	setup_iomux_fec();
> +
> +	/* Use 125M anatop REF_CLK1 for ENET1, not from external */
> +	clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0);
> +	return set_clk_enet(ENET_125MHZ);
> +}
> +
> +int board_phy_config(struct phy_device *phydev)
> +{
> +	unsigned int val;
> +
> +	/* enable rgmii rxc skew and phy mode select to RGMII copper */
> +	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
> +	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
> +
> +	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
> +	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
> +
> +	/*
> +	 * Set LED configuration register 1:
> +	 * LED2_SEL: 0b1011 (link established, blink on activity)
> +	 */
> +	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x18);
> +	val &= 0xf0ff;
> +	phy_write(phydev, MDIO_DEVAD_NONE, 0x18, val | (0xb << 8));
> +
> +	if (phydev->drv->config)
> +		phydev->drv->config(phydev);
> +	return 0;
> +}
> +#endif
> +
> +int board_init(void)
> +{
> +#ifdef CONFIG_FEC_MXC
> +	setup_fec();
> +#endif
> +
> +#if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_DWC3)
> +	init_usb_clk();
> +#endif
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_MISC_INIT_R
> +#define TPM_RESET    IMX_GPIO_NR(3, 2)
> +#define USBHUB_RESET IMX_GPIO_NR(3, 4)
> +
> +static void reset_device_by_gpio(const char *label, int pin, int delay_ms)
> +{
> +	gpio_request(pin, label);
> +	gpio_direction_output(pin, 0);
> +	mdelay(delay_ms);
> +	gpio_direction_output(pin, 1);
> +}
> +
> +int misc_init_r(void)
> +{
> +	/*
> +	 * reset TPM chip (Infineon SLB9670) as required by datasheet
> +	 * (60ms minimum Reset Inactive Time, 70ms implemented)
> +	 */
> +	reset_device_by_gpio("tpm_reset", TPM_RESET, 70);
> +
> +	/*
> +	 * reset USB hub as required by datasheet
> +	 * (3ms minimum reset duration, 10ms implemented)
> +	 */
> +	reset_device_by_gpio("usbhub_reset", USBHUB_RESET, 10);
> +
> +	return 0;
> +}
> +#endif
> +
> +int board_mmc_get_env_dev(int devno)
> +{
> +	return devno;
> +}
> +
> +int board_late_init(void)
> +{
> +	return 0;
> +}
> diff --git a/board/kontron/pitx_imx8m/spl.c b/board/kontron/pitx_imx8m/spl.c
> new file mode 100644
> index 0000000000..ddf20d5e23
> --- /dev/null
> +++ b/board/kontron/pitx_imx8m/spl.c
> @@ -0,0 +1,327 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <fsl_esdhc_imx.h>
> +#include <hang.h>
> +#include <init.h>
> +#include <log.h>
> +#include <spl.h>
> +#include <asm/arch/ddr.h>
> +#include <asm/arch/imx8mq_pins.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/arch/clock.h>
> +#include <asm/global_data.h>
> +#include <asm/io.h>
> +#include <asm/mach-imx/iomux-v3.h>
> +#include <asm/mach-imx/gpio.h>
> +#include <asm/mach-imx/mxc_i2c.h>
> +#include <linux/delay.h>
> +#include <power/pmic.h>
> +#include <power/pfuze100_pmic.h>
> +
> +extern struct dram_timing_info dram_timing_2gb;
> +extern struct dram_timing_info dram_timing_4gb;
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int pfuze_mode_init(struct pmic *p, u32 mode)
> +{
> +	unsigned char offset, i, switch_num;
> +	u32 id;
> +	int ret;
> +
> +	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
> +	id = id & 0xf;
> +
> +	if (id == 0) {
> +		switch_num = 6;
> +		offset = PFUZE100_SW1CMODE;
> +	} else if (id == 1) {
> +		switch_num = 4;
> +		offset = PFUZE100_SW2MODE;
> +	} else {
> +		printf("Not supported, id=%d\n", id);
> +		return -EINVAL;
> +	}
> +
> +	ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
> +	if (ret < 0) {
> +		printf("Set SW1AB mode error!\n");
> +		return ret;
> +	}
> +
> +	for (i = 0; i < switch_num - 1; i++) {
> +		ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
> +		if (ret < 0) {
> +			printf("Set switch 0x%x mode error!\n",
> +			       offset + i * SWITCH_SIZE);
> +			return ret;
> +		}
> +	}
> +
> +	return ret;
> +}
> +
> +/*
> + *   BRD_REV1   BRD_REV0
> + *      0         0         n/a
> + *      0         1         n/a
> + *      1         0         2GB LPDDR4
> + *      1         1         4GB LPDDR4
> + */
> +
> +#define BRD_REV0  IMX_GPIO_NR(5, 0)
> +#define BRD_REV1  IMX_GPIO_NR(5, 1)
> +
> +static iomux_v3_cfg_t const brdrev_pads[] = {
> +	IMX8MQ_PAD_SAI3_TXC__GPIO5_IO0 | MUX_PAD_CTRL(PAD_CTL_PUE),
> +	IMX8MQ_PAD_SAI3_TXD__GPIO5_IO1 | MUX_PAD_CTRL(PAD_CTL_PUE),
> +	IMX8MQ_PAD_SAI3_MCLK__GPIO5_IO2 | MUX_PAD_CTRL(PAD_CTL_PUE),
> +};
> +
> +static void spl_dram_init(void)
> +{
> +	struct dram_timing_info *dram_timing;
> +	int variant = 0, size;
> +
> +	imx_iomux_v3_setup_multiple_pads(brdrev_pads, ARRAY_SIZE(brdrev_pads));
> +
> +	gpio_request(BRD_REV0, "BRD_REV0");
> +	gpio_direction_input(BRD_REV0);
> +	gpio_request(BRD_REV1, "BRD_REV1");
> +	gpio_direction_input(BRD_REV1);
> +
> +	variant |= !!gpio_get_value(BRD_REV0) << 0;
> +	variant |= !!gpio_get_value(BRD_REV1) << 1;
> +
> +	switch(variant) {
> +	case 2:
> +		dram_timing = &dram_timing_2gb;
> +		size = 2;
> +		break;
> +	case 3:
> +		dram_timing = &dram_timing_4gb;
> +		size = 4;
> +		break;
> +	default:
> +		printf("Unknown DDR type (%d)\n", variant);
> +		return;
> +	};
> +
> +	/* ddr init */
> +	ddr_init(dram_timing);
> +}
> +
> +#define I2C_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
> +static struct i2c_pads_info i2c_pad_info1 = {
> +	.scl = {
> +		.i2c_mode = IMX8MQ_PAD_I2C1_SCL__I2C1_SCL | PC,
> +		.gpio_mode = IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 | PC,
> +		.gp = IMX_GPIO_NR(5, 14),
> +	},
> +	.sda = {
> +		.i2c_mode = IMX8MQ_PAD_I2C1_SDA__I2C1_SDA | PC,
> +		.gpio_mode = IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 | PC,
> +		.gp = IMX_GPIO_NR(5, 15),
> +	},
> +};
> +
> +#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 12)
> +#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10)
> +#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
> +
> +int board_mmc_getcd(struct mmc *mmc)
> +{
> +	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
> +	int ret = 0;
> +
> +	switch (cfg->esdhc_base) {
> +	case USDHC1_BASE_ADDR:
> +		ret = 1;
> +		break;
> +	case USDHC2_BASE_ADDR:
> +		ret = !gpio_get_value(USDHC2_CD_GPIO);
> +		return ret;
> +	}
> +
> +	return 1;
> +}
> +
> +#define USDHC_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \
> +			 PAD_CTL_FSEL2)
> +#define USDHC_GPIO_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_DSE1)
> +
> +static iomux_v3_cfg_t const usdhc1_pads[] = {
> +	IMX8MQ_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const usdhc2_pads[] = {
> +	IMX8MQ_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
> +	IMX8MQ_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
> +	IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
> +	IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
> +	IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0x16 */
> +	IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
> +	IMX8MQ_PAD_SD2_CD_B__GPIO2_IO12 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
> +	IMX8MQ_PAD_SD2_RESET_B__GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
> +};
> +
> +static struct fsl_esdhc_cfg usdhc_cfg[2] = {
> +	{USDHC1_BASE_ADDR, 0, 8},
> +	{USDHC2_BASE_ADDR, 0, 4},
> +};
> +
> +int board_mmc_init(struct bd_info *bis)
> +{
> +	int i, ret;
> +	/*
> +	 * According to the board_mmc_init() the following map is done:
> +	 * (U-Boot device node)    (Physical Port)
> +	 * mmc0                    USDHC1
> +	 * mmc1                    USDHC2
> +	 */
> +	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
> +		switch (i) {
> +		case 0:
> +			init_clk_usdhc(0);
> +			usdhc_cfg[0].sdhc_clk = mxc_get_clock(USDHC1_CLK_ROOT);
> +			imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
> +							 ARRAY_SIZE(usdhc1_pads));
> +			gpio_request(USDHC1_PWR_GPIO, "usdhc1_reset");
> +			gpio_direction_output(USDHC1_PWR_GPIO, 0);
> +			udelay(500);
> +			gpio_direction_output(USDHC1_PWR_GPIO, 1);
> +			break;
> +		case 1:
> +			init_clk_usdhc(1);
> +			usdhc_cfg[1].sdhc_clk = mxc_get_clock(USDHC2_CLK_ROOT);
> +			imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
> +							 ARRAY_SIZE(usdhc2_pads));
> +			gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
> +			gpio_direction_output(USDHC2_PWR_GPIO, 0);
> +			udelay(500);
> +			gpio_direction_output(USDHC2_PWR_GPIO, 1);
> +			break;
> +		default:
> +			printf("Warning: you configured more USDHC controllers "
> +				"(%d) than supported by the board\n", i + 1);
> +			return -EINVAL;
> +		}
> +
> +		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +#if CONFIG_IS_ENABLED(POWER_LEGACY)
> +#define I2C_PMIC	0
> +int power_init_board(void)
> +{
> +	struct pmic *p;
> +	int ret;
> +	unsigned int reg;
> +
> +	ret = power_pfuze100_init(I2C_PMIC);
> +	if (ret)
> +		return -ENODEV;
> +
> +	p = pmic_get("PFUZE100");
> +	ret = pmic_probe(p);
> +	if (ret)
> +		return -ENODEV;
> +
> +	pmic_reg_read(p, PFUZE100_SW3AVOL, &reg);
> +	if ((reg & 0x3f) != 0x18) {
> +		reg &= ~0x3f;
> +		reg |= 0x18;
> +		pmic_reg_write(p, PFUZE100_SW3AVOL, reg);
> +	}
> +
> +	ret = pfuze_mode_init(p, APS_PFM);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* set SW3A standby mode to off */
> +	pmic_reg_read(p, PFUZE100_SW3AMODE, &reg);
> +	reg &= ~0xf;
> +	reg |= APS_OFF;
> +	pmic_reg_write(p, PFUZE100_SW3AMODE, reg);
> +
> +	return 0;
> +}
> +#endif
> +
> +void spl_board_init(void)
> +{
> +	u32 boot_device = spl_boot_device();
> +
> +	if (boot_device == BOOT_DEVICE_MMC1) {
> +		puts("Booting from eMMC");
> +	} else if (boot_device == BOOT_DEVICE_MMC2) {
> +		puts("Booting from SD card");
> +	} else {
> +		puts("Unknown boot source");
> +	}
> +}
> +
> +#ifdef CONFIG_SPL_LOAD_FIT
> +int board_fit_config_name_match(const char *name)
> +{
> +	/* Just empty function now - can't decide what to choose */
> +	debug("%s: %s\n", __func__, name);
> +
> +	return 0;
> +}
> +#endif
> +
> +void board_init_f(ulong dummy)
> +{
> +	int ret;
> +
> +	/* Clear global data */
> +	memset((void *)gd, 0, sizeof(gd_t));
> +
> +	arch_cpu_init();
> +
> +	init_uart_clk(2);
> +
> +	board_early_init_f();
> +
> +	timer_init();
> +
> +	preloader_console_init();
> +
> +	/* Clear the BSS. */
> +	memset(__bss_start, 0, __bss_end - __bss_start);
> +
> +	ret = spl_init();
> +	if (ret) {
> +		debug("spl_init() failed: %d\n", ret);
> +		hang();
> +	}
> +
> +	enable_tzc380();
> +
> +	setup_i2c(0, 100000, 0x7f, &i2c_pad_info1);
> +
> +	power_init_board();
> +
> +	spl_dram_init();
> +
> +	board_init_r(NULL, 0);
> +}
> diff --git a/configs/kontron_pitx_imx8m_defconfig b/configs/kontron_pitx_imx8m_defconfig
> new file mode 100644
> index 0000000000..be01b3a918
> --- /dev/null
> +++ b/configs/kontron_pitx_imx8m_defconfig
> @@ -0,0 +1,87 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_IMX8M=y
> +CONFIG_SYS_TEXT_BASE=0x40200000
> +CONFIG_ENV_SIZE=0x4000
> +CONFIG_ENV_OFFSET=0x300000
> +CONFIG_SYS_I2C_MXC_I2C1=y
> +CONFIG_SYS_I2C_MXC_I2C2=y
> +CONFIG_SYS_I2C_MXC_I2C3=y
> +CONFIG_SYS_MALLOC_LEN=0x600000
> +CONFIG_DM_GPIO=y
> +CONFIG_DEFAULT_DEVICE_TREE="imx8mq-kontron-pitx-imx8m"
> +CONFIG_SPL_TEXT_BASE=0x7E1000
> +CONFIG_TARGET_KONTRON_PITX_IMX8M=y
> +CONFIG_SPL_SERIAL=y
> +CONFIG_SPL=y
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_SYS_LOAD_ADDR=0x40480000
> +CONFIG_FIT=y
> +CONFIG_SPL_FIT_PRINT=y
> +CONFIG_SPL_LOAD_FIT=y
> +# CONFIG_USE_SPL_FIT_GENERATOR is not set
> +CONFIG_BOARD_EARLY_INIT_F=y
> +CONFIG_BOARD_LATE_INIT=y
> +CONFIG_MISC_INIT_R=y
> +CONFIG_SPL_BOARD_INIT=y
> +# CONFIG_BOOTM_NETBSD is not set
> +# CONFIG_CMD_EXPORTENV is not set
> +# CONFIG_CMD_IMPORTENV is not set
> +CONFIG_CMD_NVEDIT_EFI=y
> +# CONFIG_CMD_CRC32 is not set
> +CONFIG_CMD_DFU=y
> +CONFIG_CMD_FUSE=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +# CONFIG_RANDOM_UUID is not set
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_MDIO is not set
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EFIDEBUG=y
> +CONFIG_CMD_RTC=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_CMD_HASH=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_ENV_OVERWRITE=y
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SYS_MMC_ENV_DEV=1
> +CONFIG_SYS_MMC_ENV_PART=1
> +CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
> +CONFIG_DFU_MMC=y
> +CONFIG_MXC_GPIO=y
> +CONFIG_DM_I2C=y
> +CONFIG_SPL_SYS_I2C_LEGACY=y
> +CONFIG_SUPPORT_EMMC_BOOT=y
> +CONFIG_FSL_USDHC=y
> +CONFIG_PHYLIB=y
> +CONFIG_PHY_TI=y
> +CONFIG_DM_ETH=y
> +CONFIG_PHY=y
> +CONFIG_PHY_IMX8MQ_USB=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_IMX8M=y
> +CONFIG_SPL_POWER_LEGACY=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_IMX8M_POWER_DOMAIN=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_SPL_POWER_I2C=y
> +CONFIG_DM_RESET=y
> +CONFIG_DM_RTC=y
> +CONFIG_RTC_RV8803=y
> +CONFIG_MXC_UART=y
> +CONFIG_DM_THERMAL=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_DWC3=y
> +CONFIG_EFI_SET_TIME=y
> +CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y
> +CONFIG_EFI_CAPSULE_ON_DISK=y
> +CONFIG_EFI_IGNORE_OSINDICATIONS=y
> +CONFIG_EFI_CAPSULE_FIRMWARE_FIT=y
> diff --git a/doc/board/kontron/index.rst b/doc/board/kontron/index.rst
> index 543b22e2f5..6baaf4d7a5 100644
> --- a/doc/board/kontron/index.rst
> +++ b/doc/board/kontron/index.rst
> @@ -6,4 +6,5 @@ Kontron
>   .. toctree::
>      :maxdepth: 2
>   
> +   pitx-imx8m
>      sl28
> diff --git a/doc/board/kontron/pitx-imx8m.rst b/doc/board/kontron/pitx-imx8m.rst
> new file mode 100644
> index 0000000000..1f64cbd9b2
> --- /dev/null
> +++ b/doc/board/kontron/pitx-imx8m.rst
> @@ -0,0 +1,67 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +Kontron pitx-imx8m
> +==================
> +
> +The Kontron pitx-imx8m is an embedded board with an i.MX8MQ in the pITX
> +form factor.
> +
> +The board has two Ethernet ports, USB, HDMI/LVDS, m.2 slot, SD card, CAN,
> +RS232 and much more.
> +
> +Quick Start
> +-----------
> +
> +- Get and build the ARM Trusted firmware binary
> +- Get DDR and HDMI firmware
> +- Build U-Boot
> +- Install on SD card
> +- Boot
> +
> +Get and build the ARM Trusted firmware binary
> +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> +
> +Note: builddir is U-Boot build directory (source directory for in-tree builds)
> +
> +.. code-block:: bash
> +
> +    $ git clone https://github.com/ARM-software/arm-trusted-firmware.git
> +    $ git checkout v2.5
> +    $ make PLAT=imx8mq ARCH=aarch64 CROSS_COMPILE=aarch64-linux-gnu- bl31
> +    $ cp build/imx8mq/release/bl31.bin $(builddir)
> +
> +Get DDR and HDMI firmware
> +^^^^^^^^^^^^^^^^^^^^^^^^^
> +
> +Note: builddir is U-Boot build directory (source directory for in-tree builds)
> +
> +.. code-block:: bash
> +
> +    $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.11.bin
> +    $ chmod +x firmware-imx-8.11.bin
> +    $ ./firmware-imx-8.11
> +    $ cp firmware-imx-8.11/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
> +    $ cp firmware-imx-8.11/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir)
> +
> +Build U-Boot
> +^^^^^^^^^^^^
> +
> +.. code-block:: bash
> +
> +    $ make kontron_pitx_imx8m_defconfig
> +    $ make CROSS_COMPILE=aarch64-linux-gnu-
> +
> +Install on SD card
> +^^^^^^^^^^^^^^^^^^
> +
> +
> +Burn the flash.bin to SD card at an offset of 33 KiB:
> +
> +.. code-block:: bash
> +
> +    $ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33
> +
> +Boot
> +^^^^
> +
> +Set the boot source selection to SD card boot and power on the board.
> diff --git a/include/configs/kontron_pitx_imx8m.h b/include/configs/kontron_pitx_imx8m.h
> new file mode 100644
> index 0000000000..952dbd445c
> --- /dev/null
> +++ b/include/configs/kontron_pitx_imx8m.h
> @@ -0,0 +1,111 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +
> +#ifndef __KONTRON_PITX_IMX8M_H
> +#define __KONTRON_PITX_IMX8M_H
> +
> +#include <linux/sizes.h>
> +#include <linux/stringify.h>
> +#include <asm/arch/imx-regs.h>
> +
> +#define CONFIG_SYS_BOOTM_LEN		(32 * SZ_1M)
> +
> +#define CONFIG_SPL_MAX_SIZE		(124 * SZ_1K)
> +#define CONFIG_SYS_MONITOR_LEN		(512 * SZ_1K)
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
> +
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_SPL_WATCHDOG
> +#define CONFIG_SPL_DRIVERS_MISC
> +#define CONFIG_SPL_POWER
> +#define CONFIG_SPL_I2C
> +#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
> +#define CONFIG_SPL_STACK		0x187FF0
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +#define CONFIG_SPL_GPIO
> +#define CONFIG_SPL_MMC
> +#define CONFIG_SPL_BSS_START_ADDR       0x00180000
> +#define CONFIG_SPL_BSS_MAX_SIZE         SZ_8K
> +#define CONFIG_SYS_SPL_MALLOC_START     0x42200000
> +#define CONFIG_SYS_SPL_MALLOC_SIZE      SZ_512K
> +#define CONFIG_SYS_SPL_PTE_RAM_BASE     0x41580000
> +
> +/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
> +#define CONFIG_MALLOC_F_ADDR		0x182000
> +/* For RAW image gives a error info not panic */
> +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
> +
> +#undef CONFIG_DM_MMC
> +
> +#define CONFIG_POWER_PFUZE100
> +#define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
> +#endif
> +
> +#define CONFIG_REMAKE_ELF
> +
> +/* ENET1 Config */
> +#if defined(CONFIG_CMD_NET)
> +#define CONFIG_MII
> +#define CONFIG_ETHPRIME                 "FEC"
> +
> +#define CONFIG_FEC_MXC
> +#define CONFIG_FEC_XCV_TYPE             RGMII
> +#define CONFIG_FEC_MXC_PHYADDR          0
> +#define FEC_QUIRK_ENET_MAC
> +
> +#define CONFIG_PHY_GIGE
> +#define IMX_FEC_BASE			0x30BE0000
> +#define PHY_ANEG_TIMEOUT		20000
> +
> +#endif
> +
> +#define ENV_MEM_LAYOUT_SETTINGS \
> +	"kernel_addr_r=0x40880000\0" \
> +	"fdt_addr_r=0x43000000\0" \
> +	"scriptaddr=0x43500000\0" \
> +	"initrd_addr=0x43800000\0" \
> +	"pxefile_addr_r=0x43500000\0" \
> +	"bootm_size=0x10000000\0" \
> +
> +#define BOOT_TARGET_DEVICES(func) \
> +	func(MMC, mmc, 0) \
> +	func(MMC, mmc, 1) \
> +	func(USB, usb, 0) \
> +	func(DHCP, dhcp, na) \
> +	func(PXE, pxe, 0)
> +
> +#include <config_distro_bootcmd.h>
> +
> +/* Initial environment variables */
> +#define CONFIG_EXTRA_ENV_SETTINGS		\
> +	"image=Image\0" \
> +	"console=ttymxc2,115200\0" \
> +	"boot_fdt=try\0" \
> +	"fdtfile=freescale/imx8mq-kontron-pitx-imx8m.dtb\0" \
> +	"dfu_alt_info=mmc 0=flash-bin raw 0x42 0x1000 mmcpart 1\0"\
> +	ENV_MEM_LAYOUT_SETTINGS \
> +	BOOTENV
> +
> +
> +#define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
> +#define CONFIG_SYS_INIT_RAM_SIZE        0x80000
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +#define CONFIG_SYS_SDRAM_BASE           0x40000000
> +#define PHYS_SDRAM                      0x40000000
> +#define PHYS_SDRAM_SIZE			0xC0000000 /* 3GB DDR */
> +
> +#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
> +
> +#define CONFIG_IMX_BOOTAUX
> +
> +#define CONFIG_SYS_FSL_USDHC_NUM	2
> +#define CONFIG_SYS_FSL_ESDHC_ADDR       0
> +
> +#define CONFIG_OF_SYSTEM_SETUP
> +
> +#endif
>

Hi Stefano,


Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>
> Hi Heiko,
>
> On 14.10.21 20:08, Heiko Thiery wrote:
> > The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> > form factor.
> >
>
> There is still something using binman that does not work with CI.
> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
>
> But on CI, file is not loaded, but instead of warnings, build for this
> board fails with :
>
> +Image 'main-section' is missing external blobs and is non-functional:
> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> file or directory
> +
>
> Could you take a look ?

Sure. Could you point me to the right CI configuration?

I need to understand how the required imx-firmware files are copied to
the u-boot dir. This seems to work already for e. g. the imx8mm
boards. These require the lpdd* train fw files.

On 21.10.21 15:17, Heiko Thiery wrote:
> Hi Stefano,
> 
> 
> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>>
>> Hi Heiko,
>>
>> On 14.10.21 20:08, Heiko Thiery wrote:
>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
>>> form factor.
>>>
>>
>> There is still something using binman that does not work with CI.
>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
>>
>> But on CI, file is not loaded, but instead of warnings, build for this
>> board fails with :
>>
>> +Image 'main-section' is missing external blobs and is non-functional:
>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
>> file or directory
>> +
>>
>> Could you take a look ?
> 
> Sure. Could you point me to the right CI configuration?
> 

Configuration is in .gitlab-ci.yml. For thsi board, buildman is called 
as part of aarch64 target, that is

	buildman -o /tmp -P -E -W arm -x aarch64

> I need to understand how the required imx-firmware files are copied to
> the u-boot dir. This seems to work already for e. g. the imx8mm
> boards. These require the lpdd* train fw files.

Regards,
Stefano

Hi Stefano, Hi Simon,


Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>
> On 21.10.21 15:17, Heiko Thiery wrote:
> > Hi Stefano,
> >
> >
> > Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> >>
> >> Hi Heiko,
> >>
> >> On 14.10.21 20:08, Heiko Thiery wrote:
> >>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> >>> form factor.
> >>>
> >>
> >> There is still something using binman that does not work with CI.
> >> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> >>
> >> But on CI, file is not loaded, but instead of warnings, build for this
> >> board fails with :
> >>
> >> +Image 'main-section' is missing external blobs and is non-functional:
> >> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> >> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> >> file or directory
> >> +
> >>
> >> Could you take a look ?
> >
> > Sure. Could you point me to the right CI configuration?
> >
>
> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> as part of aarch64 target, that is
>
>         buildman -o /tmp -P -E -W arm -x aarch64
>
> > I need to understand how the required imx-firmware files are copied to
> > the u-boot dir. This seems to work already for e. g. the imx8mm
> > boards. These require the lpdd* train fw files.

Here we seem to hit an issue with the CI. blobs (lpddr*) are required
for the imx8mm boards. Binman reports the missing files only as a
warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----

With the imx8mq boards switching to binman we also need an additional
fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
file or directory
----

Currently I do not have an idea how to handle that. Anyone else?

Hi Stefano, Hi Simon,

Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
<heiko.thiery@gmail.com>:
>
> Hi Stefano, Hi Simon,
>
>
> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> >
> > On 21.10.21 15:17, Heiko Thiery wrote:
> > > Hi Stefano,
> > >
> > >
> > > Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > >>
> > >> Hi Heiko,
> > >>
> > >> On 14.10.21 20:08, Heiko Thiery wrote:
> > >>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> > >>> form factor.
> > >>>
> > >>
> > >> There is still something using binman that does not work with CI.
> > >> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> > >>
> > >> But on CI, file is not loaded, but instead of warnings, build for this
> > >> board fails with :
> > >>
> > >> +Image 'main-section' is missing external blobs and is non-functional:
> > >> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> > >> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > >> file or directory
> > >> +
> > >>
> > >> Could you take a look ?
> > >
> > > Sure. Could you point me to the right CI configuration?
> > >
> >
> > Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> > as part of aarch64 target, that is
> >
> >         buildman -o /tmp -P -E -W arm -x aarch64
> >
> > > I need to understand how the required imx-firmware files are copied to
> > > the u-boot dir. This seems to work already for e. g. the imx8mm
> > > boards. These require the lpdd* train fw files.
>
> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
> for the imx8mm boards. Binman reports the missing files only as a
> warning and buildman does not care about that:
> ----
> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
> ----
>
> With the imx8mq boards switching to binman we also need an additional
> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
> with an error. Thats leads to the error:
> ----
> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> file or directory
> ----
>
> Currently I do not have an idea how to handle that. Anyone else?

I thought about it a little and did a quick hack. What do you think
about dummy files being generated for buildman? I had buildman
generate the blobs needed by binman. So at least the build runs
through successfully. I don't know yet how to integrate this sensibly
into buildman or if this is useful for the maintainers at all. But
this would get rid of the warnings and errors that come from binman.


diff --git a/tools/buildman/board.py b/tools/buildman/board.py
index 447aaabea8..cf270c8b72 100644
--- a/tools/buildman/board.py
+++ b/tools/buildman/board.py
@@ -96,6 +96,28 @@ class Board:
                       self.vendor, self.soc, self.options]
         self.build_it = False

+    def create_dummy_files(self, work_dir):
+        import configparser
+        import os
+
+        settings = configparser.SafeConfigParser()
+        config_fname = '%s/.buildman/' % os.getenv('HOME')
+        if os.path.exists(config_fname):
+            settings.read(config_fname)
+
+        if self.target == "kontron_pitx_imx8m":
+
+            dummy_files = ['bl31.bin',
+                           'signed_hdmi_imx8m.bin',
+                           'lpddr4_pmu_train_1d_imem.bin',
+                           'lpddr4_pmu_train_1d_dmem.bin',
+                           'lpddr4_pmu_train_2d_imem.bin',
+                           'lpddr4_pmu_train_2d_dmem.bin'
+                          ]
+            for dummy_file in dummy_files:
+                dummy = os.path.join(work_dir, 'build', dummy_file)
+                with open(dummy, "wb") as out:
+                    out.truncate(1024)

 class Boards:
     """Manage a list of boards."""
diff --git a/tools/buildman/builderthread.py b/tools/buildman/builderthread.py
index 48128cf673..dee7d9b0fe 100644
--- a/tools/buildman/builderthread.py
+++ b/tools/buildman/builderthread.py
@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread):
         """
         brd = job.board
         work_dir = self.builder.GetThreadDir(self.thread_num)
+        brd.create_dummy_files(work_dir)
         self.toolchain = None
         if job.commits:
             # Run 'make board_defconfig' on the first commit

Hi Heiko,

On 22.10.21 10:19, Heiko Thiery wrote:
> Hi Stefano, Hi Simon,
> 
> Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
> <heiko.thiery@gmail.com>:
>>
>> Hi Stefano, Hi Simon,
>>
>>
>> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>>>
>>> On 21.10.21 15:17, Heiko Thiery wrote:
>>>> Hi Stefano,
>>>>
>>>>
>>>> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>>>>>
>>>>> Hi Heiko,
>>>>>
>>>>> On 14.10.21 20:08, Heiko Thiery wrote:
>>>>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
>>>>>> form factor.
>>>>>>
>>>>>
>>>>> There is still something using binman that does not work with CI.
>>>>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
>>>>>
>>>>> But on CI, file is not loaded, but instead of warnings, build for this
>>>>> board fails with :
>>>>>
>>>>> +Image 'main-section' is missing external blobs and is non-functional:
>>>>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
>>>>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
>>>>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
>>>>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
>>>>> file or directory
>>>>> +
>>>>>
>>>>> Could you take a look ?
>>>>
>>>> Sure. Could you point me to the right CI configuration?
>>>>
>>>
>>> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
>>> as part of aarch64 target, that is
>>>
>>>          buildman -o /tmp -P -E -W arm -x aarch64
>>>
>>>> I need to understand how the required imx-firmware files are copied to
>>>> the u-boot dir. This seems to work already for e. g. the imx8mm
>>>> boards. These require the lpdd* train fw files.
>>
>> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
>> for the imx8mm boards. Binman reports the missing files only as a
>> warning and buildman does not care about that:
>> ----
>> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
>> ----
>>
>> With the imx8mq boards switching to binman we also need an additional
>> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
>> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
>> with an error. Thats leads to the error:
>> ----
>> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
>> file or directory
>> ----
>>
>> Currently I do not have an idea how to handle that. Anyone else?
> 
> I thought about it a little and did a quick hack. What do you think
> about dummy files being generated for buildman?

I had quite the same idea...

> I had buildman
> generate the blobs needed by binman. So at least the build runs
> through successfully.

But it should be checked if files are present - I guess there are people 
relying on buildman to produce the functional bootloader, and a dummy 
file cannot overwrite the right one if present.

> I don't know yet how to integrate this sensibly
> into buildman or if this is useful for the maintainers at all. But
> this would get rid of the warnings and errors that come from binman.
> 
> 
> diff --git a/tools/buildman/board.py b/tools/buildman/board.py
> index 447aaabea8..cf270c8b72 100644
> --- a/tools/buildman/board.py
> +++ b/tools/buildman/board.py
> @@ -96,6 +96,28 @@ class Board:
>                         self.vendor, self.soc, self.options]
>           self.build_it = False
> 
> +    def create_dummy_files(self, work_dir):
> +        import configparser
> +        import os
> +
> +        settings = configparser.SafeConfigParser()
> +        config_fname = '%s/.buildman/' % os.getenv('HOME')
> +        if os.path.exists(config_fname):
> +            settings.read(config_fname)
> +
> +        if self.target == "kontron_pitx_imx8m":
> +
> +            dummy_files = ['bl31.bin',
> +                           'signed_hdmi_imx8m.bin',
> +                           'lpddr4_pmu_train_1d_imem.bin',
> +                           'lpddr4_pmu_train_1d_dmem.bin',
> +                           'lpddr4_pmu_train_2d_imem.bin',
> +                           'lpddr4_pmu_train_2d_dmem.bin'
> +                          ]
> +            for dummy_file in dummy_files:
> +                dummy = os.path.join(work_dir, 'build', dummy_file)
> +                with open(dummy, "wb") as out:
> +                    out.truncate(1024)
> 
>   class Boards:
>       """Manage a list of boards."""
> diff --git a/tools/buildman/builderthread.py b/tools/buildman/builderthread.py
> index 48128cf673..dee7d9b0fe 100644
> --- a/tools/buildman/builderthread.py
> +++ b/tools/buildman/builderthread.py
> @@ -475,6 +475,7 @@ class BuilderThread(threading.Thread):
>           """
>           brd = job.board
>           work_dir = self.builder.GetThreadDir(self.thread_num)
> +        brd.create_dummy_files(work_dir)
>           self.toolchain = None
>           if job.commits:
>               # Run 'make board_defconfig' on the first commit
> 

Best regards,
Stefano

Hi,

Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <sbabic@denx.de>:
>
> Hi Heiko,
>
> On 22.10.21 10:19, Heiko Thiery wrote:
> > Hi Stefano, Hi Simon,
> >
> > Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
> > <heiko.thiery@gmail.com>:
> >>
> >> Hi Stefano, Hi Simon,
> >>
> >>
> >> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> >>>
> >>> On 21.10.21 15:17, Heiko Thiery wrote:
> >>>> Hi Stefano,
> >>>>
> >>>>
> >>>> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> >>>>>
> >>>>> Hi Heiko,
> >>>>>
> >>>>> On 14.10.21 20:08, Heiko Thiery wrote:
> >>>>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> >>>>>> form factor.
> >>>>>>
> >>>>>
> >>>>> There is still something using binman that does not work with CI.
> >>>>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> >>>>>
> >>>>> But on CI, file is not loaded, but instead of warnings, build for this
> >>>>> board fails with :
> >>>>>
> >>>>> +Image 'main-section' is missing external blobs and is non-functional:
> >>>>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> >>>>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> >>>>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> >>>>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> >>>>> file or directory
> >>>>> +
> >>>>>
> >>>>> Could you take a look ?
> >>>>
> >>>> Sure. Could you point me to the right CI configuration?
> >>>>
> >>>
> >>> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> >>> as part of aarch64 target, that is
> >>>
> >>>          buildman -o /tmp -P -E -W arm -x aarch64
> >>>
> >>>> I need to understand how the required imx-firmware files are copied to
> >>>> the u-boot dir. This seems to work already for e. g. the imx8mm
> >>>> boards. These require the lpdd* train fw files.
> >>
> >> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
> >> for the imx8mm boards. Binman reports the missing files only as a
> >> warning and buildman does not care about that:
> >> ----
> >> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
> >> ----
> >>
> >> With the imx8mq boards switching to binman we also need an additional
> >> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
> >> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
> >> with an error. Thats leads to the error:
> >> ----
> >> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> >> file or directory
> >> ----
> >>
> >> Currently I do not have an idea how to handle that. Anyone else?
> >
> > I thought about it a little and did a quick hack. What do you think
> > about dummy files being generated for buildman?
>
> I had quite the same idea...
>
> > I had buildman
> > generate the blobs needed by binman. So at least the build runs
> > through successfully.
>
> But it should be checked if files are present - I guess there are people
> relying on buildman to produce the functional bootloader, and a dummy
> file cannot overwrite the right one if present.

Sure. As said ,this was only a quick hack to see if it could work.
Another thing is if there should be a config for each board that says
what files have to be created.

> > I don't know yet how to integrate this sensibly
> > into buildman or if this is useful for the maintainers at all. But
> > this would get rid of the warnings and errors that come from binman.
> >
> >
> > diff --git a/tools/buildman/board.py b/tools/buildman/board.py
> > index 447aaabea8..cf270c8b72 100644
> > --- a/tools/buildman/board.py
> > +++ b/tools/buildman/board.py
> > @@ -96,6 +96,28 @@ class Board:
> >                         self.vendor, self.soc, self.options]
> >           self.build_it = False
> >
> > +    def create_dummy_files(self, work_dir):
> > +        import configparser
> > +        import os
> > +
> > +        settings = configparser.SafeConfigParser()
> > +        config_fname = '%s/.buildman/' % os.getenv('HOME')
> > +        if os.path.exists(config_fname):
> > +            settings.read(config_fname)
> > +
> > +        if self.target == "kontron_pitx_imx8m":
> > +
> > +            dummy_files = ['bl31.bin',
> > +                           'signed_hdmi_imx8m.bin',
> > +                           'lpddr4_pmu_train_1d_imem.bin',
> > +                           'lpddr4_pmu_train_1d_dmem.bin',
> > +                           'lpddr4_pmu_train_2d_imem.bin',
> > +                           'lpddr4_pmu_train_2d_dmem.bin'
> > +                          ]
> > +            for dummy_file in dummy_files:
> > +                dummy = os.path.join(work_dir, 'build', dummy_file)
> > +                with open(dummy, "wb") as out:
> > +                    out.truncate(1024)
> >
> >   class Boards:
> >       """Manage a list of boards."""
> > diff --git a/tools/buildman/builderthread.py b/tools/buildman/builderthread.py
> > index 48128cf673..dee7d9b0fe 100644
> > --- a/tools/buildman/builderthread.py
> > +++ b/tools/buildman/builderthread.py
> > @@ -475,6 +475,7 @@ class BuilderThread(threading.Thread):
> >           """
> >           brd = job.board
> >           work_dir = self.builder.GetThreadDir(self.thread_num)
> > +        brd.create_dummy_files(work_dir)
> >           self.toolchain = None
> >           if job.commits:
> >               # Run 'make board_defconfig' on the first commit
> >

Hi Heiko,

On Fri, 22 Oct 2021 at 07:24, Heiko Thiery <heiko.thiery@gmail.com> wrote:
>
> Hi,
>
> Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> >
> > Hi Heiko,
> >
> > On 22.10.21 10:19, Heiko Thiery wrote:
> > > Hi Stefano, Hi Simon,
> > >
> > > Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
> > > <heiko.thiery@gmail.com>:
> > >>
> > >> Hi Stefano, Hi Simon,
> > >>
> > >>
> > >> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > >>>
> > >>> On 21.10.21 15:17, Heiko Thiery wrote:
> > >>>> Hi Stefano,
> > >>>>
> > >>>>
> > >>>> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > >>>>>
> > >>>>> Hi Heiko,
> > >>>>>
> > >>>>> On 14.10.21 20:08, Heiko Thiery wrote:
> > >>>>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> > >>>>>> form factor.
> > >>>>>>
> > >>>>>
> > >>>>> There is still something using binman that does not work with CI.
> > >>>>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> > >>>>>
> > >>>>> But on CI, file is not loaded, but instead of warnings, build for this
> > >>>>> board fails with :
> > >>>>>
> > >>>>> +Image 'main-section' is missing external blobs and is non-functional:
> > >>>>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> > >>>>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > >>>>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > >>>>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > >>>>> file or directory
> > >>>>> +
> > >>>>>
> > >>>>> Could you take a look ?
> > >>>>
> > >>>> Sure. Could you point me to the right CI configuration?
> > >>>>
> > >>>
> > >>> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> > >>> as part of aarch64 target, that is
> > >>>
> > >>>          buildman -o /tmp -P -E -W arm -x aarch64
> > >>>
> > >>>> I need to understand how the required imx-firmware files are copied to
> > >>>> the u-boot dir. This seems to work already for e. g. the imx8mm
> > >>>> boards. These require the lpdd* train fw files.
> > >>
> > >> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
> > >> for the imx8mm boards. Binman reports the missing files only as a
> > >> warning and buildman does not care about that:
> > >> ----
> > >> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
> > >> ----
> > >>
> > >> With the imx8mq boards switching to binman we also need an additional
> > >> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
> > >> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
> > >> with an error. Thats leads to the error:
> > >> ----
> > >> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > >> file or directory
> > >> ----
> > >>
> > >> Currently I do not have an idea how to handle that. Anyone else?

If I understand correctly:

1.You don't have these blobs in the tree so don't want to fail a build
in CI, which is why binman's blob-ext is used
2. You sometimes need to ensure that they do exist

Should we add a cmdline flag to binman to require all external blobs?

Could we drop the blobs and add code to generate them, or put the date
in a C struct?

> > >
> > > I thought about it a little and did a quick hack. What do you think
> > > about dummy files being generated for buildman?
> >
> > I had quite the same idea...
> >
> > > I had buildman
> > > generate the blobs needed by binman. So at least the build runs
> > > through successfully.
> >
> > But it should be checked if files are present - I guess there are people
> > relying on buildman to produce the functional bootloader, and a dummy
> > file cannot overwrite the right one if present.
>
> Sure. As said ,this was only a quick hack to see if it could work.
> Another thing is if there should be a config for each board that says
> what files have to be created.
>
> > > I don't know yet how to integrate this sensibly
> > > into buildman or if this is useful for the maintainers at all. But
> > > this would get rid of the warnings and errors that come from binman.
> > >
> > >
> > > diff --git a/tools/buildman/board.py b/tools/buildman/board.py
> > > index 447aaabea8..cf270c8b72 100644
> > > --- a/tools/buildman/board.py
> > > +++ b/tools/buildman/board.py
> > > @@ -96,6 +96,28 @@ class Board:
> > >                         self.vendor, self.soc, self.options]
> > >           self.build_it = False
> > >
> > > +    def create_dummy_files(self, work_dir):
> > > +        import configparser
> > > +        import os
> > > +
> > > +        settings = configparser.SafeConfigParser()
> > > +        config_fname = '%s/.buildman/' % os.getenv('HOME')
> > > +        if os.path.exists(config_fname):
> > > +            settings.read(config_fname)
> > > +
> > > +        if self.target == "kontron_pitx_imx8m":
> > > +
> > > +            dummy_files = ['bl31.bin',
> > > +                           'signed_hdmi_imx8m.bin',
> > > +                           'lpddr4_pmu_train_1d_imem.bin',
> > > +                           'lpddr4_pmu_train_1d_dmem.bin',
> > > +                           'lpddr4_pmu_train_2d_imem.bin',
> > > +                           'lpddr4_pmu_train_2d_dmem.bin'
> > > +                          ]
> > > +            for dummy_file in dummy_files:
> > > +                dummy = os.path.join(work_dir, 'build', dummy_file)
> > > +                with open(dummy, "wb") as out:
> > > +                    out.truncate(1024)
> > >
> > >   class Boards:
> > >       """Manage a list of boards."""
> > > diff --git a/tools/buildman/builderthread.py b/tools/buildman/builderthread.py
> > > index 48128cf673..dee7d9b0fe 100644
> > > --- a/tools/buildman/builderthread.py
> > > +++ b/tools/buildman/builderthread.py
> > > @@ -475,6 +475,7 @@ class BuilderThread(threading.Thread):
> > >           """
> > >           brd = job.board
> > >           work_dir = self.builder.GetThreadDir(self.thread_num)
> > > +        brd.create_dummy_files(work_dir)
> > >           self.toolchain = None
> > >           if job.commits:
> > >               # Run 'make board_defconfig' on the first commit
> > >
>
>
> --
> Heiko

Regards,
Simon

Hi Simon,

Am Fr., 22. Okt. 2021 um 18:07 Uhr schrieb Simon Glass <sjg@chromium.org>:
>
> Hi Heiko,
>
> On Fri, 22 Oct 2021 at 07:24, Heiko Thiery <heiko.thiery@gmail.com> wrote:
> >
> > Hi,
> >
> > Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > >
> > > Hi Heiko,
> > >
> > > On 22.10.21 10:19, Heiko Thiery wrote:
> > > > Hi Stefano, Hi Simon,
> > > >
> > > > Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
> > > > <heiko.thiery@gmail.com>:
> > > >>
> > > >> Hi Stefano, Hi Simon,
> > > >>
> > > >>
> > > >> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > > >>>
> > > >>> On 21.10.21 15:17, Heiko Thiery wrote:
> > > >>>> Hi Stefano,
> > > >>>>
> > > >>>>
> > > >>>> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > > >>>>>
> > > >>>>> Hi Heiko,
> > > >>>>>
> > > >>>>> On 14.10.21 20:08, Heiko Thiery wrote:
> > > >>>>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> > > >>>>>> form factor.
> > > >>>>>>
> > > >>>>>
> > > >>>>> There is still something using binman that does not work with CI.
> > > >>>>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> > > >>>>>
> > > >>>>> But on CI, file is not loaded, but instead of warnings, build for this
> > > >>>>> board fails with :
> > > >>>>>
> > > >>>>> +Image 'main-section' is missing external blobs and is non-functional:
> > > >>>>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> > > >>>>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > > >>>>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > > >>>>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > > >>>>> file or directory
> > > >>>>> +
> > > >>>>>
> > > >>>>> Could you take a look ?
> > > >>>>
> > > >>>> Sure. Could you point me to the right CI configuration?
> > > >>>>
> > > >>>
> > > >>> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> > > >>> as part of aarch64 target, that is
> > > >>>
> > > >>>          buildman -o /tmp -P -E -W arm -x aarch64
> > > >>>
> > > >>>> I need to understand how the required imx-firmware files are copied to
> > > >>>> the u-boot dir. This seems to work already for e. g. the imx8mm
> > > >>>> boards. These require the lpdd* train fw files.
> > > >>
> > > >> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
> > > >> for the imx8mm boards. Binman reports the missing files only as a
> > > >> warning and buildman does not care about that:
> > > >> ----
> > > >> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
> > > >> ----
> > > >>
> > > >> With the imx8mq boards switching to binman we also need an additional
> > > >> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
> > > >> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
> > > >> with an error. Thats leads to the error:
> > > >> ----
> > > >> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > > >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > > >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > > >> file or directory
> > > >> ----
> > > >>
> > > >> Currently I do not have an idea how to handle that. Anyone else?
>
> If I understand correctly:
>
> 1.You don't have these blobs in the tree so don't want to fail a build
> in CI, which is why binman's blob-ext is used

Correct, for the imx8mq e.g. the signed_hdmi_imx8m.bin is required
that comes from NXP and has to be copied to the u-boot build dir.

> 2. You sometimes need to ensure that they do exist

For the build the "signed_hdmi_imx8m.bin" is required to successfully build.

> Should we add a cmdline flag to binman to require all external blobs?

I do not understand that. What should happen if this flag is present?

> Could we drop the blobs and add code to generate them, or put the date
> in a C struct?

No, this is not possible because they are delivered by NXP from the
firmware-imx package and has to be copied from there.

> > > >
> > > > I thought about it a little and did a quick hack. What do you think
> > > > about dummy files being generated for buildman?
> > >
> > > I had quite the same idea...
> > >
> > > > I had buildman
> > > > generate the blobs needed by binman. So at least the build runs
> > > > through successfully.
> > >
> > > But it should be checked if files are present - I guess there are people
> > > relying on buildman to produce the functional bootloader, and a dummy
> > > file cannot overwrite the right one if present.
> >
> > Sure. As said ,this was only a quick hack to see if it could work.
> > Another thing is if there should be a config for each board that says
> > what files have to be created.
> >
> > > > I don't know yet how to integrate this sensibly
> > > > into buildman or if this is useful for the maintainers at all. But
> > > > this would get rid of the warnings and errors that come from binman.
> > > >
> > > >
> > > > diff --git a/tools/buildman/board.py b/tools/buildman/board.py
> > > > index 447aaabea8..cf270c8b72 100644
> > > > --- a/tools/buildman/board.py
> > > > +++ b/tools/buildman/board.py
> > > > @@ -96,6 +96,28 @@ class Board:
> > > >                         self.vendor, self.soc, self.options]
> > > >           self.build_it = False
> > > >
> > > > +    def create_dummy_files(self, work_dir):
> > > > +        import configparser
> > > > +        import os
> > > > +
> > > > +        settings = configparser.SafeConfigParser()
> > > > +        config_fname = '%s/.buildman/' % os.getenv('HOME')
> > > > +        if os.path.exists(config_fname):
> > > > +            settings.read(config_fname)
> > > > +
> > > > +        if self.target == "kontron_pitx_imx8m":
> > > > +
> > > > +            dummy_files = ['bl31.bin',
> > > > +                           'signed_hdmi_imx8m.bin',
> > > > +                           'lpddr4_pmu_train_1d_imem.bin',
> > > > +                           'lpddr4_pmu_train_1d_dmem.bin',
> > > > +                           'lpddr4_pmu_train_2d_imem.bin',
> > > > +                           'lpddr4_pmu_train_2d_dmem.bin'
> > > > +                          ]
> > > > +            for dummy_file in dummy_files:
> > > > +                dummy = os.path.join(work_dir, 'build', dummy_file)
> > > > +                with open(dummy, "wb") as out:
> > > > +                    out.truncate(1024)
> > > >
> > > >   class Boards:
> > > >       """Manage a list of boards."""
> > > > diff --git a/tools/buildman/builderthread.py b/tools/buildman/builderthread.py
> > > > index 48128cf673..dee7d9b0fe 100644
> > > > --- a/tools/buildman/builderthread.py
> > > > +++ b/tools/buildman/builderthread.py
> > > > @@ -475,6 +475,7 @@ class BuilderThread(threading.Thread):
> > > >           """
> > > >           brd = job.board
> > > >           work_dir = self.builder.GetThreadDir(self.thread_num)
> > > > +        brd.create_dummy_files(work_dir)
> > > >           self.toolchain = None
> > > >           if job.commits:
> > > >               # Run 'make board_defconfig' on the first commit
> > > >
> >
> >
> > --
> > Heiko
>
> Regards,
> Simon

Hi Heiko,

On Fri, 22 Oct 2021 at 11:54, Heiko Thiery <heiko.thiery@gmail.com> wrote:
>
> Hi Simon,
>
> Am Fr., 22. Okt. 2021 um 18:07 Uhr schrieb Simon Glass <sjg@chromium.org>:
> >
> > Hi Heiko,
> >
> > On Fri, 22 Oct 2021 at 07:24, Heiko Thiery <heiko.thiery@gmail.com> wrote:
> > >
> > > Hi,
> > >
> > > Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > > >
> > > > Hi Heiko,
> > > >
> > > > On 22.10.21 10:19, Heiko Thiery wrote:
> > > > > Hi Stefano, Hi Simon,
> > > > >
> > > > > Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery
> > > > > <heiko.thiery@gmail.com>:
> > > > >>
> > > > >> Hi Stefano, Hi Simon,
> > > > >>
> > > > >>
> > > > >> Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > > > >>>
> > > > >>> On 21.10.21 15:17, Heiko Thiery wrote:
> > > > >>>> Hi Stefano,
> > > > >>>>
> > > > >>>>
> > > > >>>> Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <sbabic@denx.de>:
> > > > >>>>>
> > > > >>>>> Hi Heiko,
> > > > >>>>>
> > > > >>>>> On 14.10.21 20:08, Heiko Thiery wrote:
> > > > >>>>>> The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX
> > > > >>>>>> form factor.
> > > > >>>>>>
> > > > >>>>>
> > > > >>>>> There is still something using binman that does not work with CI.
> > > > >>>>> Without CI, we load all firmware including signed_hdmi_imx8m.bin.
> > > > >>>>>
> > > > >>>>> But on CI, file is not loaded, but instead of warnings, build for this
> > > > >>>>> board fails with :
> > > > >>>>>
> > > > >>>>> +Image 'main-section' is missing external blobs and is non-functional:
> > > > >>>>> blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
> > > > >>>>> +binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > > > >>>>> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > > > >>>>> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > > > >>>>> file or directory
> > > > >>>>> +
> > > > >>>>>
> > > > >>>>> Could you take a look ?
> > > > >>>>
> > > > >>>> Sure. Could you point me to the right CI configuration?
> > > > >>>>
> > > > >>>
> > > > >>> Configuration is in .gitlab-ci.yml. For thsi board, buildman is called
> > > > >>> as part of aarch64 target, that is
> > > > >>>
> > > > >>>          buildman -o /tmp -P -E -W arm -x aarch64
> > > > >>>
> > > > >>>> I need to understand how the required imx-firmware files are copied to
> > > > >>>> the u-boot dir. This seems to work already for e. g. the imx8mm
> > > > >>>> boards. These require the lpdd* train fw files.
> > > > >>
> > > > >> Here we seem to hit an issue with the CI. blobs (lpddr*) are required
> > > > >> for the imx8mm boards. Binman reports the missing files only as a
> > > > >> warning and buildman does not care about that:
> > > > >> ----
> > > > >> +WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
> > > > >> ----
> > > > >>
> > > > >> With the imx8mq boards switching to binman we also need an additional
> > > > >> fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as
> > > > >> blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits
> > > > >> with an error. Thats leads to the error:
> > > > >> ----
> > > > >> binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n
> > > > >> spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000
> > > > >> ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such
> > > > >> file or directory
> > > > >> ----
> > > > >>
> > > > >> Currently I do not have an idea how to handle that. Anyone else?
> >
> > If I understand correctly:
> >
> > 1.You don't have these blobs in the tree so don't want to fail a build
> > in CI, which is why binman's blob-ext is used
>
> Correct, for the imx8mq e.g. the signed_hdmi_imx8m.bin is required
> that comes from NXP and has to be copied to the u-boot build dir.
>
> > 2. You sometimes need to ensure that they do exist
>
> For the build the "signed_hdmi_imx8m.bin" is required to successfully build.
>
> > Should we add a cmdline flag to binman to require all external blobs?
>
> I do not understand that. What should happen if this flag is present?
>
> > Could we drop the blobs and add code to generate them, or put the date
> > in a C struct?
>
> No, this is not possible because they are delivered by NXP from the
> firmware-imx package and has to be copied from there.

Perhaps they should upstream that stuff and turn it into code in U-Boot?

Anyway, I think you are working on this, per the irc chat.
[..]

Regards,
Simon