@@ -42,7 +42,16 @@ _start: b reset
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
-
+#ifdef CONFIG_SPL_BUILD
+_undefined_instruction: .word _undefined_instruction
+_software_interrupt: .word _software_interrupt
+_prefetch_abort: .word _prefetch_abort
+_data_abort: .word _data_abort
+_not_used: .word _not_used
+_irq: .word _irq
+_fiq: .word _fiq
+_pad: .word 0x12345678 /* now 16*4=64 */
+#else
_undefined_instruction: .word undefined_instruction
_software_interrupt: .word software_interrupt
_prefetch_abort: .word prefetch_abort
@@ -51,6 +60,8 @@ _not_used: .word not_used
_irq: .word irq
_fiq: .word fiq
_pad: .word 0x12345678 /* now 16*4=64 */
+#endif /* CONFIG_SPL_BUILD */
+
.global _end_vect
_end_vect:
@@ -89,6 +100,10 @@ _armboot_start:
_bss_start_ofs:
.word __bss_start - _start
+.global _image_copy_end_ofs
+_image_copy_end_ofs:
+ .word __image_copy_end - _start
+
.globl _bss_end_ofs
_bss_end_ofs:
.word __bss_end__ - _start
@@ -182,12 +197,11 @@ stack_setup:
mov sp, r4
adr r0, _start
-#ifndef CONFIG_SPL_BUILD
cmp r0, r6
+ moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
beq clear_bss /* skip relocation */
-#endif
mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
+ ldr r3, _image_copy_end_ofs
add r2, r0, r3 /* r2 <- source end address */
copy_loop:
@@ -235,20 +249,34 @@ fixnext:
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
+ b clear_bss
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
+#endif /* #ifndef CONFIG_SPL_BUILD */
clear_bss:
+#ifdef CONFIG_SPL_BUILD
+ /* No relocation for SPL */
+ ldr r0, =__bss_start
+ ldr r1, =__bss_end__
+#else
ldr r0, _bss_start_ofs
ldr r1, _bss_end_ofs
mov r4, r6 /* reloc addr */
add r0, r0, r4
add r1, r1, r4
+#endif
mov r2, #0x00000000 /* clear */
clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
bne clbss_l
-#endif /* #ifndef CONFIG_SPL_BUILD */
/*
* We are done. Do not return, instead branch to second part of board
@@ -276,13 +304,6 @@ jump_2_ram:
_board_init_r_ofs:
.word board_init_r - _start
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*************************************************************************
*
* CPU_init_critical registers
@@ -327,6 +348,8 @@ cpu_init_crit:
bl lowlevel_init @ go setup pll,mux,memory
mov lr, ip @ restore link
mov pc, lr @ back to my caller
+
+#ifndef CONFIG_SPL_BUILD
/*
*************************************************************************
*
@@ -514,4 +537,5 @@ fiq:
bad_save_user_regs
bl do_fiq
-#endif
+#endif /* CONFIG_USE_IRQ */
+#endif /* CONFIG_SPL_BUILD */
@@ -55,6 +55,8 @@ SECTIONS
. = ALIGN(4);
+ __image_copy_end = .;
+
.rel.dyn : {
__rel_dyn_start = .;
*(.rel*)
- Allow SPL to have .bss disjoint from rest of the image - Allow for .bss setup in CONFIG_SPL_BUILD case too. - Take care of the special case where relocation offset = 0. - Compile out exception handling code and install a simpler vector Signed-off-by: Aneesh V <aneesh@ti.com> --- V3: * Taken care of the case where .bss is at a lower address comapred to _start --- arch/arm/cpu/armv7/start.S | 50 ++++++++++++++++++++++++++++++---------- arch/arm/cpu/armv7/u-boot.lds | 2 + 2 files changed, 39 insertions(+), 13 deletions(-)