diff mbox series

[v4,04/10] PCI: apple: Add initial hardware bring-up

Message ID 20210922205458.358517-5-maz@kernel.org
State New
Headers show
Series PCI: Add support for Apple M1 | expand

Commit Message

Marc Zyngier Sept. 22, 2021, 8:54 p.m. UTC 
From: Alyssa Rosenzweig <alyssa@rosenzweig.io>

Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
particularly the Apple M1. This driver exposes the internal bus used for
the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
radios requires additional drivers beyond what's necessary for PCIe
itself.

At this stage, nothing is functionnal.

Co-developed-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
---
 MAINTAINERS                         |   7 +
 drivers/pci/controller/Kconfig      |  12 ++
 drivers/pci/controller/Makefile     |   1 +
 drivers/pci/controller/pcie-apple.c | 243 ++++++++++++++++++++++++++++
 4 files changed, 263 insertions(+)
 create mode 100644 drivers/pci/controller/pcie-apple.c

Comments

Sven Peter Sept. 22, 2021, 9:08 p.m. UTC | #1 
Hi,


On Wed, Sep 22, 2021, at 22:54, Marc Zyngier wrote:
> From: Alyssa Rosenzweig <alyssa@rosenzweig.io>
>
[...]
> +
> +	/* Use the first reg entry to work out the port index */
> +	port->idx = idx >> 11;
> +	port->pcie = pcie;
> +	port->np = np;
> +
> +	port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
> +	if (IS_ERR(port->base))
> +		return -ENODEV;
> +
> +	rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);

I think this should be

    rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);

> +
> +	rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
> +	gpiod_set_value(reset, 1);
> +
> +	ret = readl_relaxed_poll_timeout(port->base + PORT_STATUS, stat,
> +					 stat & PORT_STATUS_READY, 100, 250000);
> +	if (ret < 0) {
> +		dev_err(pcie->dev, "port %pOF ready wait timeout\n", np);
> +		return ret;
> +	}
> +
> +	/* Flush writes and enable the link */
> +	dma_wmb();

I don't think this barrier is required.

> +
> +	writel_relaxed(PORT_LTSSMCTL_START, port->base + PORT_LTSSMCTL);
> +
> +	return 0;
> +}
> +
[...]


Looks good to me otherwise,

Reviewed-by: Sven Peter <sven@svenpeter.dev>


Thanks,


Sven
Rob Herring Sept. 22, 2021, 9:09 p.m. UTC | #2 
On Wed, Sep 22, 2021 at 3:55 PM Marc Zyngier <maz@kernel.org> wrote:
>
> From: Alyssa Rosenzweig <alyssa@rosenzweig.io>
>
> Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
> particularly the Apple M1. This driver exposes the internal bus used for
> the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
> radios requires additional drivers beyond what's necessary for PCIe
> itself.
>
> At this stage, nothing is functionnal.
>
> Co-developed-by: Stan Skowronek <stan@corellium.com>
> Signed-off-by: Stan Skowronek <stan@corellium.com>
> Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> Signed-off-by: Marc Zyngier <maz@kernel.org>
> ---
>  MAINTAINERS                         |   7 +
>  drivers/pci/controller/Kconfig      |  12 ++
>  drivers/pci/controller/Makefile     |   1 +
>  drivers/pci/controller/pcie-apple.c | 243 ++++++++++++++++++++++++++++
>  4 files changed, 263 insertions(+)
>  create mode 100644 drivers/pci/controller/pcie-apple.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index ba3e2419e86a..18fc0ed9a7f6 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1280,6 +1280,13 @@ S:       Maintained
>  F:     Documentation/devicetree/bindings/iommu/apple,dart.yaml
>  F:     drivers/iommu/apple-dart.c
>
> +APPLE PCIE CONTROLLER DRIVER
> +M:     Alyssa Rosenzweig <alyssa@rosenzweig.io>
> +M:     Marc Zyngier <maz@kernel.org>
> +L:     linux-pci@vger.kernel.org
> +S:     Maintained
> +F:     drivers/pci/controller/pcie-apple.c
> +
>  APPLE SMC DRIVER
>  M:     Henrik Rydberg <rydberg@bitmath.org>
>  L:     linux-hwmon@vger.kernel.org
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 326f7d13024f..814833a8120d 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -312,6 +312,18 @@ config PCIE_HISI_ERR
>           Say Y here if you want error handling support
>           for the PCIe controller's errors on HiSilicon HIP SoCs
>
> +config PCIE_APPLE
> +       tristate "Apple PCIe controller"
> +       depends on ARCH_APPLE || COMPILE_TEST
> +       depends on OF
> +       depends on PCI_MSI_IRQ_DOMAIN
> +       help
> +         Say Y here if you want to enable PCIe controller support on Apple
> +         system-on-chips, like the Apple M1. This is required for the USB
> +         type-A ports, Ethernet, Wi-Fi, and Bluetooth.
> +
> +         If unsure, say Y if you have an Apple Silicon system.
> +
>  source "drivers/pci/controller/dwc/Kconfig"
>  source "drivers/pci/controller/mobiveil/Kconfig"
>  source "drivers/pci/controller/cadence/Kconfig"
> diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile
> index aaf30b3dcc14..f9d40bad932c 100644
> --- a/drivers/pci/controller/Makefile
> +++ b/drivers/pci/controller/Makefile
> @@ -37,6 +37,7 @@ obj-$(CONFIG_VMD) += vmd.o
>  obj-$(CONFIG_PCIE_BRCMSTB) += pcie-brcmstb.o
>  obj-$(CONFIG_PCI_LOONGSON) += pci-loongson.o
>  obj-$(CONFIG_PCIE_HISI_ERR) += pcie-hisi-error.o
> +obj-$(CONFIG_PCIE_APPLE) += pcie-apple.o
>  # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
>  obj-y                          += dwc/
>  obj-y                          += mobiveil/
> diff --git a/drivers/pci/controller/pcie-apple.c b/drivers/pci/controller/pcie-apple.c
> new file mode 100644
> index 000000000000..2479a4168439
> --- /dev/null
> +++ b/drivers/pci/controller/pcie-apple.c
> @@ -0,0 +1,243 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * PCIe host bridge driver for Apple system-on-chips.
> + *
> + * The HW is ECAM compliant, so once the controller is initialized,
> + * the driver mostly deals MSI mapping and handling of per-port
> + * interrupts (INTx, management and error signals).
> + *
> + * Initialization requires enabling power and clocks, along with a
> + * number of register pokes.
> + *
> + * Copyright (C) 2021 Alyssa Rosenzweig <alyssa@rosenzweig.io>
> + * Copyright (C) 2021 Google LLC
> + * Copyright (C) 2021 Corellium LLC
> + * Copyright (C) 2021 Mark Kettenis <kettenis@openbsd.org>
> + *
> + * Author: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> + * Author: Marc Zyngier <maz@kernel.org>
> + */
> +
> +#include <linux/gpio/consumer.h>
> +#include <linux/kernel.h>
> +#include <linux/iopoll.h>
> +#include <linux/irqdomain.h>
> +#include <linux/module.h>
> +#include <linux/msi.h>
> +#include <linux/of_irq.h>
> +#include <linux/pci-ecam.h>
> +
> +#define CORE_RC_PHYIF_CTL              0x00024
> +#define   CORE_RC_PHYIF_CTL_RUN                BIT(0)
> +#define CORE_RC_PHYIF_STAT             0x00028
> +#define   CORE_RC_PHYIF_STAT_REFCLK    BIT(4)
> +#define CORE_RC_CTL                    0x00050
> +#define   CORE_RC_CTL_RUN              BIT(0)
> +#define CORE_RC_STAT                   0x00058
> +#define   CORE_RC_STAT_READY           BIT(0)
> +#define CORE_FABRIC_STAT               0x04000
> +#define   CORE_FABRIC_STAT_MASK                0x001F001F
> +#define CORE_LANE_CFG(port)            (0x84000 + 0x4000 * (port))
> +#define   CORE_LANE_CFG_REFCLK0REQ     BIT(0)
> +#define   CORE_LANE_CFG_REFCLK1                BIT(1)
> +#define   CORE_LANE_CFG_REFCLK0ACK     BIT(2)
> +#define   CORE_LANE_CFG_REFCLKEN       (BIT(9) | BIT(10))
> +#define CORE_LANE_CTL(port)            (0x84004 + 0x4000 * (port))
> +#define   CORE_LANE_CTL_CFGACC         BIT(15)
> +
> +#define PORT_LTSSMCTL                  0x00080
> +#define   PORT_LTSSMCTL_START          BIT(0)
> +#define PORT_INTSTAT                   0x00100
> +#define   PORT_INT_TUNNEL_ERR          31
> +#define   PORT_INT_CPL_TIMEOUT         23
> +#define   PORT_INT_RID2SID_MAPERR      22
> +#define   PORT_INT_CPL_ABORT           21
> +#define   PORT_INT_MSI_BAD_DATA                19
> +#define   PORT_INT_MSI_ERR             18
> +#define   PORT_INT_REQADDR_GT32                17
> +#define   PORT_INT_AF_TIMEOUT          15
> +#define   PORT_INT_LINK_DOWN           14
> +#define   PORT_INT_LINK_UP             12
> +#define   PORT_INT_LINK_BWMGMT         11
> +#define   PORT_INT_AER_MASK            (15 << 4)
> +#define   PORT_INT_PORT_ERR            4
> +#define   PORT_INT_INTx(i)             i
> +#define   PORT_INT_INTx_MASK           15
> +#define PORT_INTMSK                    0x00104
> +#define PORT_INTMSKSET                 0x00108
> +#define PORT_INTMSKCLR                 0x0010c
> +#define PORT_MSICFG                    0x00124
> +#define   PORT_MSICFG_EN               BIT(0)
> +#define   PORT_MSICFG_L2MSINUM_SHIFT   4
> +#define PORT_MSIBASE                   0x00128
> +#define   PORT_MSIBASE_1_SHIFT         16
> +#define PORT_MSIADDR                   0x00168
> +#define PORT_LINKSTS                   0x00208
> +#define   PORT_LINKSTS_UP              BIT(0)
> +#define   PORT_LINKSTS_BUSY            BIT(2)
> +#define PORT_LINKCMDSTS                        0x00210
> +#define PORT_OUTS_NPREQS               0x00284
> +#define   PORT_OUTS_NPREQS_REQ         BIT(24)
> +#define   PORT_OUTS_NPREQS_CPL         BIT(16)
> +#define PORT_RXWR_FIFO                 0x00288
> +#define   PORT_RXWR_FIFO_HDR           GENMASK(15, 10)
> +#define   PORT_RXWR_FIFO_DATA          GENMASK(9, 0)
> +#define PORT_RXRD_FIFO                 0x0028C
> +#define   PORT_RXRD_FIFO_REQ           GENMASK(6, 0)
> +#define PORT_OUTS_CPLS                 0x00290
> +#define   PORT_OUTS_CPLS_SHRD          GENMASK(14, 8)
> +#define   PORT_OUTS_CPLS_WAIT          GENMASK(6, 0)
> +#define PORT_APPCLK                    0x00800
> +#define   PORT_APPCLK_EN               BIT(0)
> +#define   PORT_APPCLK_CGDIS            BIT(8)
> +#define PORT_STATUS                    0x00804
> +#define   PORT_STATUS_READY            BIT(0)
> +#define PORT_REFCLK                    0x00810
> +#define   PORT_REFCLK_EN               BIT(0)
> +#define   PORT_REFCLK_CGDIS            BIT(8)
> +#define PORT_PERST                     0x00814
> +#define   PORT_PERST_OFF               BIT(0)
> +#define PORT_RID2SID(i16)              (0x00828 + 4 * (i16))
> +#define   PORT_RID2SID_VALID           BIT(31)
> +#define   PORT_RID2SID_SID_SHIFT       16
> +#define   PORT_RID2SID_BUS_SHIFT       8
> +#define   PORT_RID2SID_DEV_SHIFT       3
> +#define   PORT_RID2SID_FUNC_SHIFT      0
> +#define PORT_OUTS_PREQS_HDR            0x00980
> +#define   PORT_OUTS_PREQS_HDR_MASK     GENMASK(9, 0)
> +#define PORT_OUTS_PREQS_DATA           0x00984
> +#define   PORT_OUTS_PREQS_DATA_MASK    GENMASK(15, 0)
> +#define PORT_TUNCTRL                   0x00988
> +#define   PORT_TUNCTRL_PERST_ON                BIT(0)
> +#define   PORT_TUNCTRL_PERST_ACK_REQ   BIT(1)
> +#define PORT_TUNSTAT                   0x0098c
> +#define   PORT_TUNSTAT_PERST_ON                BIT(0)
> +#define   PORT_TUNSTAT_PERST_ACK_PEND  BIT(1)
> +#define PORT_PREFMEM_ENABLE            0x00994
> +
> +struct apple_pcie {
> +       struct device           *dev;
> +       void __iomem            *base;
> +};
> +
> +struct apple_pcie_port {
> +       struct apple_pcie       *pcie;
> +       struct device_node      *np;
> +       void __iomem            *base;
> +       int                     idx;
> +};
> +
> +static void rmw_set(u32 set, void __iomem *addr)
> +{
> +       writel_relaxed(readl_relaxed(addr) | set, addr);
> +}
> +
> +static int apple_pcie_setup_port(struct apple_pcie *pcie,
> +                                struct device_node *np)
> +{
> +       struct platform_device *platform = to_platform_device(pcie->dev);
> +       struct apple_pcie_port *port;
> +       struct gpio_desc *reset;
> +       u32 stat, idx;
> +       int ret;
> +
> +       reset = gpiod_get_from_of_node(np, "reset-gpios", 0,
> +                                      GPIOD_OUT_LOW, "#PERST");
> +       if (IS_ERR(reset))
> +               return PTR_ERR(reset);
> +
> +       port = devm_kzalloc(pcie->dev, sizeof(*port), GFP_KERNEL);
> +       if (!port)
> +               return -ENOMEM;
> +
> +       ret = of_property_read_u32_index(np, "reg", 0, &idx);
> +       if (ret)
> +               return ret;
> +
> +       /* Use the first reg entry to work out the port index */
> +       port->idx = idx >> 11;
> +       port->pcie = pcie;
> +       port->np = np;
> +
> +       port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
> +       if (IS_ERR(port->base))
> +               return -ENODEV;
> +
> +       rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);
> +
> +       rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
> +       gpiod_set_value(reset, 1);
> +
> +       ret = readl_relaxed_poll_timeout(port->base + PORT_STATUS, stat,
> +                                        stat & PORT_STATUS_READY, 100, 250000);
> +       if (ret < 0) {
> +               dev_err(pcie->dev, "port %pOF ready wait timeout\n", np);
> +               return ret;
> +       }
> +
> +       /* Flush writes and enable the link */
> +       dma_wmb();

I thought this was getting removed.

Otherwise,

Reviewed-by: Rob Herring <robh@kernel.org>

> +       writel_relaxed(PORT_LTSSMCTL_START, port->base + PORT_LTSSMCTL);
> +
> +       return 0;
> +}
> +
> +static int apple_pcie_init(struct pci_config_window *cfg)
> +{
> +       struct device *dev = cfg->parent;
> +       struct platform_device *platform = to_platform_device(dev);
> +       struct device_node *of_port;
> +       struct apple_pcie *pcie;
> +       int ret;
> +
> +       pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> +       if (!pcie)
> +               return -ENOMEM;
> +
> +       pcie->dev = dev;
> +
> +       mutex_init(&pcie->lock);
> +
> +       pcie->base = devm_platform_ioremap_resource(platform, 1);
> +
> +       if (IS_ERR(pcie->base))
> +               return -ENODEV;
> +
> +       for_each_child_of_node(dev->of_node, of_port) {
> +               ret = apple_pcie_setup_port(pcie, of_port);
> +               if (ret) {
> +                       dev_err(pcie->dev, "Port %pOF setup fail: %d\n", of_port, ret);
> +                       return ret;
> +               }
> +       }
> +
> +       return 0;
> +}
> +
> +static const struct pci_ecam_ops apple_pcie_cfg_ecam_ops = {
> +       .init           = apple_pcie_init,
> +       .pci_ops        = {
> +               .map_bus        = pci_ecam_map_bus,
> +               .read           = pci_generic_config_read,
> +               .write          = pci_generic_config_write,
> +       }
> +};
> +
> +static const struct of_device_id apple_pcie_of_match[] = {
> +       { .compatible = "apple,pcie", .data = &apple_pcie_cfg_ecam_ops },
> +       { }
> +};
> +MODULE_DEVICE_TABLE(of, apple_pcie_of_match);
> +
> +static struct platform_driver apple_pcie_driver = {
> +       .probe  = pci_host_common_probe,
> +       .driver = {
> +               .name                   = "pcie-apple",
> +               .of_match_table         = apple_pcie_of_match,
> +               .suppress_bind_attrs    = true,
> +       },
> +};
> +module_platform_driver(apple_pcie_driver);
> +
> +MODULE_LICENSE("GPL v2");
> --
> 2.30.2
>
Rob Herring Sept. 22, 2021, 9:14 p.m. UTC | #3 
On Wed, Sep 22, 2021 at 4:08 PM Sven Peter <sven@svenpeter.dev> wrote:
>
> Hi,
>
>
> On Wed, Sep 22, 2021, at 22:54, Marc Zyngier wrote:
> > From: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> >
> [...]
> > +
> > +     /* Use the first reg entry to work out the port index */
> > +     port->idx = idx >> 11;
> > +     port->pcie = pcie;
> > +     port->np = np;
> > +
> > +     port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
> > +     if (IS_ERR(port->base))
> > +             return -ENODEV;

Don't change error codes.

> > +
> > +     rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);
>
> I think this should be
>
>     rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);

Or just removed if this was tested and worked.

Rob
Marc Zyngier Sept. 22, 2021, 9:24 p.m. UTC | #4 
On Wed, 22 Sep 2021 22:08:33 +0100,
"Sven Peter" <sven@svenpeter.dev> wrote:
> 
> Hi,
> 
> 
> On Wed, Sep 22, 2021, at 22:54, Marc Zyngier wrote:
> > From: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> >
> [...]
> > +
> > +	/* Use the first reg entry to work out the port index */
> > +	port->idx = idx >> 11;
> > +	port->pcie = pcie;
> > +	port->np = np;
> > +
> > +	port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
> > +	if (IS_ERR(port->base))
> > +		return -ENODEV;
> > +
> > +	rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);
> 
> I think this should be
> 
>     rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);

Ouch. Well caught. I wonder how many of these I introduced...:-/

> 
> > +
> > +	rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
> > +	gpiod_set_value(reset, 1);
> > +
> > +	ret = readl_relaxed_poll_timeout(port->base + PORT_STATUS, stat,
> > +					 stat & PORT_STATUS_READY, 100, 250000);
> > +	if (ret < 0) {
> > +		dev_err(pcie->dev, "port %pOF ready wait timeout\n", np);
> > +		return ret;
> > +	}
> > +
> > +	/* Flush writes and enable the link */
> > +	dma_wmb();
> 
> I don't think this barrier is required.

It really isn't, and I though I had removed it. I now wonder whether I
have pushed out the right branch, or messed up by moving from one
machine to another...

> > +
> > +	writel_relaxed(PORT_LTSSMCTL_START, port->base + PORT_LTSSMCTL);
> > +
> > +	return 0;
> > +}
> > +
> [...]
> 
> 
> Looks good to me otherwise,
> 
> Reviewed-by: Sven Peter <sven@svenpeter.dev>

Thanks. Hopefully I'll manage to post a non broken series next time...

	M.
Marc Zyngier Sept. 22, 2021, 9:31 p.m. UTC | #5 
On Wed, 22 Sep 2021 22:14:49 +0100,
Rob Herring <robh+dt@kernel.org> wrote:
> 
> On Wed, Sep 22, 2021 at 4:08 PM Sven Peter <sven@svenpeter.dev> wrote:
> >
> > Hi,
> >
> >
> > On Wed, Sep 22, 2021, at 22:54, Marc Zyngier wrote:
> > > From: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> > >
> > [...]
> > > +
> > > +     /* Use the first reg entry to work out the port index */
> > > +     port->idx = idx >> 11;
> > > +     port->pcie = pcie;
> > > +     port->np = np;
> > > +
> > > +     port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
> > > +     if (IS_ERR(port->base))
> > > +             return -ENODEV;
> 
> Don't change error codes.

Yup, good point. There is another instance of that when setting up a
port.

> 
> > > +
> > > +     rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);
> >
> > I think this should be
> >
> >     rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);
> 
> Or just removed if this was tested and worked.

That's probably the point where I find out that it only worked because
I was corrupting memory in bizarre ways. Oh well.

Thanks,

	M.
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index ba3e2419e86a..18fc0ed9a7f6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1280,6 +1280,13 @@  S:	Maintained
 F:	Documentation/devicetree/bindings/iommu/apple,dart.yaml
 F:	drivers/iommu/apple-dart.c
 
+APPLE PCIE CONTROLLER DRIVER
+M:	Alyssa Rosenzweig <alyssa@rosenzweig.io>
+M:	Marc Zyngier <maz@kernel.org>
+L:	linux-pci@vger.kernel.org
+S:	Maintained
+F:	drivers/pci/controller/pcie-apple.c
+
 APPLE SMC DRIVER
 M:	Henrik Rydberg <rydberg@bitmath.org>
 L:	linux-hwmon@vger.kernel.org
diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 326f7d13024f..814833a8120d 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -312,6 +312,18 @@  config PCIE_HISI_ERR
 	  Say Y here if you want error handling support
 	  for the PCIe controller's errors on HiSilicon HIP SoCs
 
+config PCIE_APPLE
+	tristate "Apple PCIe controller"
+	depends on ARCH_APPLE || COMPILE_TEST
+	depends on OF
+	depends on PCI_MSI_IRQ_DOMAIN
+	help
+	  Say Y here if you want to enable PCIe controller support on Apple
+	  system-on-chips, like the Apple M1. This is required for the USB
+	  type-A ports, Ethernet, Wi-Fi, and Bluetooth.
+
+	  If unsure, say Y if you have an Apple Silicon system.
+
 source "drivers/pci/controller/dwc/Kconfig"
 source "drivers/pci/controller/mobiveil/Kconfig"
 source "drivers/pci/controller/cadence/Kconfig"
diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile
index aaf30b3dcc14..f9d40bad932c 100644
--- a/drivers/pci/controller/Makefile
+++ b/drivers/pci/controller/Makefile
@@ -37,6 +37,7 @@  obj-$(CONFIG_VMD) += vmd.o
 obj-$(CONFIG_PCIE_BRCMSTB) += pcie-brcmstb.o
 obj-$(CONFIG_PCI_LOONGSON) += pci-loongson.o
 obj-$(CONFIG_PCIE_HISI_ERR) += pcie-hisi-error.o
+obj-$(CONFIG_PCIE_APPLE) += pcie-apple.o
 # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
 obj-y				+= dwc/
 obj-y				+= mobiveil/
diff --git a/drivers/pci/controller/pcie-apple.c b/drivers/pci/controller/pcie-apple.c
new file mode 100644
index 000000000000..2479a4168439
--- /dev/null
+++ b/drivers/pci/controller/pcie-apple.c
@@ -0,0 +1,243 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe host bridge driver for Apple system-on-chips.
+ *
+ * The HW is ECAM compliant, so once the controller is initialized,
+ * the driver mostly deals MSI mapping and handling of per-port
+ * interrupts (INTx, management and error signals).
+ *
+ * Initialization requires enabling power and clocks, along with a
+ * number of register pokes.
+ *
+ * Copyright (C) 2021 Alyssa Rosenzweig <alyssa@rosenzweig.io>
+ * Copyright (C) 2021 Google LLC
+ * Copyright (C) 2021 Corellium LLC
+ * Copyright (C) 2021 Mark Kettenis <kettenis@openbsd.org>
+ *
+ * Author: Alyssa Rosenzweig <alyssa@rosenzweig.io>
+ * Author: Marc Zyngier <maz@kernel.org>
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/iopoll.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_irq.h>
+#include <linux/pci-ecam.h>
+
+#define CORE_RC_PHYIF_CTL		0x00024
+#define   CORE_RC_PHYIF_CTL_RUN		BIT(0)
+#define CORE_RC_PHYIF_STAT		0x00028
+#define   CORE_RC_PHYIF_STAT_REFCLK	BIT(4)
+#define CORE_RC_CTL			0x00050
+#define   CORE_RC_CTL_RUN		BIT(0)
+#define CORE_RC_STAT			0x00058
+#define   CORE_RC_STAT_READY		BIT(0)
+#define CORE_FABRIC_STAT		0x04000
+#define   CORE_FABRIC_STAT_MASK		0x001F001F
+#define CORE_LANE_CFG(port)		(0x84000 + 0x4000 * (port))
+#define   CORE_LANE_CFG_REFCLK0REQ	BIT(0)
+#define   CORE_LANE_CFG_REFCLK1		BIT(1)
+#define   CORE_LANE_CFG_REFCLK0ACK	BIT(2)
+#define   CORE_LANE_CFG_REFCLKEN	(BIT(9) | BIT(10))
+#define CORE_LANE_CTL(port)		(0x84004 + 0x4000 * (port))
+#define   CORE_LANE_CTL_CFGACC		BIT(15)
+
+#define PORT_LTSSMCTL			0x00080
+#define   PORT_LTSSMCTL_START		BIT(0)
+#define PORT_INTSTAT			0x00100
+#define   PORT_INT_TUNNEL_ERR		31
+#define   PORT_INT_CPL_TIMEOUT		23
+#define   PORT_INT_RID2SID_MAPERR	22
+#define   PORT_INT_CPL_ABORT		21
+#define   PORT_INT_MSI_BAD_DATA		19
+#define   PORT_INT_MSI_ERR		18
+#define   PORT_INT_REQADDR_GT32		17
+#define   PORT_INT_AF_TIMEOUT		15
+#define   PORT_INT_LINK_DOWN		14
+#define   PORT_INT_LINK_UP		12
+#define   PORT_INT_LINK_BWMGMT		11
+#define   PORT_INT_AER_MASK		(15 << 4)
+#define   PORT_INT_PORT_ERR		4
+#define   PORT_INT_INTx(i)		i
+#define   PORT_INT_INTx_MASK		15
+#define PORT_INTMSK			0x00104
+#define PORT_INTMSKSET			0x00108
+#define PORT_INTMSKCLR			0x0010c
+#define PORT_MSICFG			0x00124
+#define   PORT_MSICFG_EN		BIT(0)
+#define   PORT_MSICFG_L2MSINUM_SHIFT	4
+#define PORT_MSIBASE			0x00128
+#define   PORT_MSIBASE_1_SHIFT		16
+#define PORT_MSIADDR			0x00168
+#define PORT_LINKSTS			0x00208
+#define   PORT_LINKSTS_UP		BIT(0)
+#define   PORT_LINKSTS_BUSY		BIT(2)
+#define PORT_LINKCMDSTS			0x00210
+#define PORT_OUTS_NPREQS		0x00284
+#define   PORT_OUTS_NPREQS_REQ		BIT(24)
+#define   PORT_OUTS_NPREQS_CPL		BIT(16)
+#define PORT_RXWR_FIFO			0x00288
+#define   PORT_RXWR_FIFO_HDR		GENMASK(15, 10)
+#define   PORT_RXWR_FIFO_DATA		GENMASK(9, 0)
+#define PORT_RXRD_FIFO			0x0028C
+#define   PORT_RXRD_FIFO_REQ		GENMASK(6, 0)
+#define PORT_OUTS_CPLS			0x00290
+#define   PORT_OUTS_CPLS_SHRD		GENMASK(14, 8)
+#define   PORT_OUTS_CPLS_WAIT		GENMASK(6, 0)
+#define PORT_APPCLK			0x00800
+#define   PORT_APPCLK_EN		BIT(0)
+#define   PORT_APPCLK_CGDIS		BIT(8)
+#define PORT_STATUS			0x00804
+#define   PORT_STATUS_READY		BIT(0)
+#define PORT_REFCLK			0x00810
+#define   PORT_REFCLK_EN		BIT(0)
+#define   PORT_REFCLK_CGDIS		BIT(8)
+#define PORT_PERST			0x00814
+#define   PORT_PERST_OFF		BIT(0)
+#define PORT_RID2SID(i16)		(0x00828 + 4 * (i16))
+#define   PORT_RID2SID_VALID		BIT(31)
+#define   PORT_RID2SID_SID_SHIFT	16
+#define   PORT_RID2SID_BUS_SHIFT	8
+#define   PORT_RID2SID_DEV_SHIFT	3
+#define   PORT_RID2SID_FUNC_SHIFT	0
+#define PORT_OUTS_PREQS_HDR		0x00980
+#define   PORT_OUTS_PREQS_HDR_MASK	GENMASK(9, 0)
+#define PORT_OUTS_PREQS_DATA		0x00984
+#define   PORT_OUTS_PREQS_DATA_MASK	GENMASK(15, 0)
+#define PORT_TUNCTRL			0x00988
+#define   PORT_TUNCTRL_PERST_ON		BIT(0)
+#define   PORT_TUNCTRL_PERST_ACK_REQ	BIT(1)
+#define PORT_TUNSTAT			0x0098c
+#define   PORT_TUNSTAT_PERST_ON		BIT(0)
+#define   PORT_TUNSTAT_PERST_ACK_PEND	BIT(1)
+#define PORT_PREFMEM_ENABLE		0x00994
+
+struct apple_pcie {
+	struct device		*dev;
+	void __iomem            *base;
+};
+
+struct apple_pcie_port {
+	struct apple_pcie	*pcie;
+	struct device_node	*np;
+	void __iomem		*base;
+	int			idx;
+};
+
+static void rmw_set(u32 set, void __iomem *addr)
+{
+	writel_relaxed(readl_relaxed(addr) | set, addr);
+}
+
+static int apple_pcie_setup_port(struct apple_pcie *pcie,
+				 struct device_node *np)
+{
+	struct platform_device *platform = to_platform_device(pcie->dev);
+	struct apple_pcie_port *port;
+	struct gpio_desc *reset;
+	u32 stat, idx;
+	int ret;
+
+	reset = gpiod_get_from_of_node(np, "reset-gpios", 0,
+				       GPIOD_OUT_LOW, "#PERST");
+	if (IS_ERR(reset))
+		return PTR_ERR(reset);
+
+	port = devm_kzalloc(pcie->dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	ret = of_property_read_u32_index(np, "reg", 0, &idx);
+	if (ret)
+		return ret;
+
+	/* Use the first reg entry to work out the port index */
+	port->idx = idx >> 11;
+	port->pcie = pcie;
+	port->np = np;
+
+	port->base = devm_platform_ioremap_resource(platform, port->idx + 2);
+	if (IS_ERR(port->base))
+		return -ENODEV;
+
+	rmw_set(PORT_APPCLK_EN, port + PORT_APPCLK);
+
+	rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
+	gpiod_set_value(reset, 1);
+
+	ret = readl_relaxed_poll_timeout(port->base + PORT_STATUS, stat,
+					 stat & PORT_STATUS_READY, 100, 250000);
+	if (ret < 0) {
+		dev_err(pcie->dev, "port %pOF ready wait timeout\n", np);
+		return ret;
+	}
+
+	/* Flush writes and enable the link */
+	dma_wmb();
+
+	writel_relaxed(PORT_LTSSMCTL_START, port->base + PORT_LTSSMCTL);
+
+	return 0;
+}
+
+static int apple_pcie_init(struct pci_config_window *cfg)
+{
+	struct device *dev = cfg->parent;
+	struct platform_device *platform = to_platform_device(dev);
+	struct device_node *of_port;
+	struct apple_pcie *pcie;
+	int ret;
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	pcie->dev = dev;
+
+	mutex_init(&pcie->lock);
+
+	pcie->base = devm_platform_ioremap_resource(platform, 1);
+
+	if (IS_ERR(pcie->base))
+		return -ENODEV;
+
+	for_each_child_of_node(dev->of_node, of_port) {
+		ret = apple_pcie_setup_port(pcie, of_port);
+		if (ret) {
+			dev_err(pcie->dev, "Port %pOF setup fail: %d\n", of_port, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static const struct pci_ecam_ops apple_pcie_cfg_ecam_ops = {
+	.init		= apple_pcie_init,
+	.pci_ops	= {
+		.map_bus	= pci_ecam_map_bus,
+		.read		= pci_generic_config_read,
+		.write		= pci_generic_config_write,
+	}
+};
+
+static const struct of_device_id apple_pcie_of_match[] = {
+	{ .compatible = "apple,pcie", .data = &apple_pcie_cfg_ecam_ops },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, apple_pcie_of_match);
+
+static struct platform_driver apple_pcie_driver = {
+	.probe	= pci_host_common_probe,
+	.driver	= {
+		.name			= "pcie-apple",
+		.of_match_table		= apple_pcie_of_match,
+		.suppress_bind_attrs	= true,
+	},
+};
+module_platform_driver(apple_pcie_driver);
+
+MODULE_LICENSE("GPL v2");