@@ -13,7 +13,7 @@ obj-$(CONFIG_AXP152_POWER) += axp152.o
obj-$(CONFIG_AXP209_POWER) += axp209.o
obj-$(CONFIG_AXP221_POWER) += axp221.o
obj-$(CONFIG_AXP305_POWER) += axp305.o
-obj-$(CONFIG_AXP313_POWER) += axp313.o
+obj-$(CONFIG_AXP313_POWER) += axp_spl.o
obj-$(CONFIG_AXP717_POWER) += axp_spl.o
obj-$(CONFIG_AXP809_POWER) += axp809.o
obj-$(CONFIG_AXP818_POWER) += axp818.o
deleted file mode 100644
@@ -1,133 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * AXP313(a) driver
- *
- * (C) Copyright 2023 Arm Ltd.
- *
- * Based on axp305.c
- * (C) Copyright 2020 Jernej Skrabec <jernej.skrabec@siol.net>
- * (C) Copyright 2014 Hans de Goede <hdegoede@redhat.com>
- * (C) Copyright 2013 Oliver Schinagl <oliver@schinagl.nl>
- */
-
-#include <command.h>
-#include <errno.h>
-#include <asm/arch/pmic_bus.h>
-#include <axp_pmic.h>
-
-enum axp313_reg {
- AXP313_CHIP_VERSION = 0x03,
- AXP313_OUTPUT_CTRL = 0x10,
- AXP313_DCDC1_CTRL = 0x13,
- AXP313_SHUTDOWN = 0x1a,
-};
-
-#define AXP313_CHIP_VERSION_MASK 0xcf
-#define AXP313_CHIP_VERSION_AXP1530 0x48
-#define AXP313_CHIP_VERSION_AXP313A 0x4b
-#define AXP313_CHIP_VERSION_AXP313B 0x4c
-
-#define AXP313_DCDC_SPLIT_OFFSET 71
-#define AXP313_DCDC_SPLIT_MVOLT 1200
-
-#define AXP313_POWEROFF BIT(7)
-
-static u8 mvolt_to_cfg(int mvolt, int min, int max, int div)
-{
- if (mvolt < min)
- mvolt = min;
- else if (mvolt > max)
- mvolt = max;
-
- return (mvolt - min) / div;
-}
-
-static int axp_set_dcdc(int dcdc_num, unsigned int mvolt)
-{
- int ret;
- u8 cfg, enable_mask = 1U << (dcdc_num - 1);
- int volt_reg = AXP313_DCDC1_CTRL + dcdc_num - 1;
- int max_mV;
-
- switch (dcdc_num) {
- case 1:
- case 2:
- max_mV = 1540;
- break;
- case 3:
- /*
- * The manual defines a different split point, but tests
- * show that it's the same 1200mV as for DCDC1/2.
- */
- max_mV = 1840;
- break;
- default:
- return -EINVAL;
- }
-
- if (mvolt > AXP313_DCDC_SPLIT_MVOLT)
- cfg = AXP313_DCDC_SPLIT_OFFSET + mvolt_to_cfg(mvolt,
- AXP313_DCDC_SPLIT_MVOLT + 20, max_mV, 20);
- else
- cfg = mvolt_to_cfg(mvolt, 500, AXP313_DCDC_SPLIT_MVOLT, 10);
-
- if (mvolt == 0)
- return pmic_bus_clrbits(AXP313_OUTPUT_CTRL, enable_mask);
-
- debug("DCDC%d: writing 0x%x to reg 0x%x\n", dcdc_num, cfg, volt_reg);
- ret = pmic_bus_write(volt_reg, cfg);
- if (ret)
- return ret;
-
- return pmic_bus_setbits(AXP313_OUTPUT_CTRL, enable_mask);
-}
-
-int axp_set_dcdc2(unsigned int mvolt)
-{
- return axp_set_dcdc(2, mvolt);
-}
-
-int axp_set_dcdc3(unsigned int mvolt)
-{
- return axp_set_dcdc(3, mvolt);
-}
-
-int axp_init(void)
-{
- u8 axp_chip_id;
- int ret;
-
- ret = pmic_bus_init();
- if (ret)
- return ret;
-
- ret = pmic_bus_read(AXP313_CHIP_VERSION, &axp_chip_id);
- if (ret)
- return ret;
-
- axp_chip_id &= AXP313_CHIP_VERSION_MASK;
- switch (axp_chip_id) {
- case AXP313_CHIP_VERSION_AXP1530:
- case AXP313_CHIP_VERSION_AXP313A:
- case AXP313_CHIP_VERSION_AXP313B:
- break;
- default:
- debug("unknown PMIC: 0x%x\n", axp_chip_id);
- return -EINVAL;
- }
-
- return ret;
-}
-
-#if !CONFIG_IS_ENABLED(ARM_PSCI_FW) && !IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF)
-int do_poweroff(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- pmic_bus_write(AXP313_SHUTDOWN, AXP313_POWEROFF);
-
- /* infinite loop during shutdown */
- while (1) {}
-
- /* not reached */
- return 0;
-}
-#endif
@@ -34,6 +34,19 @@ static const struct axp_reg_desc_spl axp_spl_dcdc_regulators[] = {
#define AXP_SHUTDOWN_REG 0x27
#define AXP_SHUTDOWN_MASK BIT(0)
+#elif defined(CONFIG_AXP313_POWER) /* AXP313 */
+
+static const struct axp_reg_desc_spl axp_spl_dcdc_regulators[] = {
+ { 0x10, BIT(0), 0x13, 0x7f, 500, 1540, 10, 70 },
+ { 0x10, BIT(1), 0x14, 0x7f, 500, 1540, 10, 70 },
+ { 0x10, BIT(2), 0x15, 0x7f, 500, 1840, 10, 70 },
+};
+#define AXP_CHIP_VERSION 0x3
+#define AXP_CHIP_VERSION_MASK 0xc8
+#define AXP_CHIP_ID 0x48
+#define AXP_SHUTDOWN_REG 0x1a
+#define AXP_SHUTDOWN_MASK BIT(7)
+
#else
#error "Please define the regulator registers in axp_spl_regulators[]."
The generic AXP SPL driver implementation can cover all regulators we need for the AXP313. Add the descriptions for the three DC/DC regulators of the AXP313, and enable that when CONFIG_AXP313_POWER is enabled. Also remove the old driver, and switch the Makefile to include the new, generic version. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- drivers/power/Makefile | 2 +- drivers/power/axp313.c | 133 ---------------------------------------- drivers/power/axp_spl.c | 13 ++++ 3 files changed, 14 insertions(+), 134 deletions(-) delete mode 100644 drivers/power/axp313.c