new file mode 100644
@@ -0,0 +1,209 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_SWITCH_MAP_H
+#define __NET_TI_ICSSG_SWITCH_MAP_H
+
+/*Time after which FDB entries are checked for aged out values. Value in nanoseconds*/
+#define FDB_AGEING_TIMEOUT_OFFSET 0x0014
+
+/*default VLAN tag for Host Port*/
+#define HOST_PORT_DF_VLAN_OFFSET 0x001C
+
+/*Same as HOST_PORT_DF_VLAN_OFFSET*/
+#define EMAC_ICSSG_SWITCH_PORT0_DEFAULT_VLAN_OFFSET HOST_PORT_DF_VLAN_OFFSET
+
+/*default VLAN tag for P1 Port*/
+#define P1_PORT_DF_VLAN_OFFSET 0x0020
+
+/*Same as P1_PORT_DF_VLAN_OFFSET*/
+#define EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET P1_PORT_DF_VLAN_OFFSET
+
+/*default VLAN tag for P2 Port*/
+#define P2_PORT_DF_VLAN_OFFSET 0x0024
+
+/*Same as P2_PORT_DF_VLAN_OFFSET*/
+#define EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET P2_PORT_DF_VLAN_OFFSET
+
+/*VLAN-FID Table offset. 4096 VIDs. 2B per VID = 8KB = 0x2000*/
+#define VLAN_STATIC_REG_TABLE_OFFSET 0x0100
+
+/*VLAN-FID Table offset for EMAC*/
+#define EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET VLAN_STATIC_REG_TABLE_OFFSET
+
+/*packet descriptor Q reserved memory*/
+#define PORT_DESC0_HI 0x2104
+
+/*packet descriptor Q reserved memory*/
+#define PORT_DESC0_LO 0x2F6C
+
+/*packet descriptor Q reserved memory*/
+#define PORT_DESC1_HI 0x3DD4
+
+/*packet descriptor Q reserved memory*/
+#define PORT_DESC1_LO 0x4C3C
+
+/*packet descriptor Q reserved memory*/
+#define HOST_DESC0_HI 0x5AA4
+
+/*packet descriptor Q reserved memory*/
+#define HOST_DESC0_LO 0x5F0C
+
+/*packet descriptor Q reserved memory*/
+#define HOST_DESC1_HI 0x6374
+
+/*packet descriptor Q reserved memory*/
+#define HOST_DESC1_LO 0x67DC
+
+/*special packet descriptor Q reserved memory*/
+#define HOST_SPPD0 0x7AAC
+
+/*special packet descriptor Q reserved memory*/
+#define HOST_SPPD1 0x7EAC
+
+/*_Small_Description_*/
+#define TIMESYNC_FW_WC_CYCLECOUNT_OFFSET 0x83EC
+
+/*IEP count hi roll over count*/
+#define TIMESYNC_FW_WC_HI_ROLLOVER_COUNT_OFFSET 0x83F4
+
+/*_Small_Description_*/
+#define TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET 0x83F8
+
+/*Set clock descriptor*/
+#define TIMESYNC_FW_WC_SETCLOCK_DESC_OFFSET 0x83FC
+
+/*_Small_Description_*/
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_FACTOR_OFFSET 0x843C
+
+/*_Small_Description_*/
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_COUNT_OFFSET 0x8440
+
+/*_Small_Description_*/
+#define TIMESYNC_FW_WC_SYNCOUT_START_TIME_CYCLECOUNT_OFFSET 0x8444
+
+/*Control variable to generate SYNC1*/
+#define TIMESYNC_FW_WC_ISOM_PIN_SIGNAL_EN_OFFSET 0x844C
+
+/*SystemTime Sync0 periodicity*/
+#define TIMESYNC_FW_ST_SYNCOUT_PERIOD_OFFSET 0x8450
+
+/*pktTxDelay for P1 = link speed dependent p1 mac delay + p1 phy delay*/
+#define TIMESYNC_FW_WC_PKTTXDELAY_P1_OFFSET 0x8454
+
+/*pktTxDelay for P2 = link speed dependent p2 mac delay + p2 phy delay*/
+#define TIMESYNC_FW_WC_PKTTXDELAY_P2_OFFSET 0x8458
+
+/*Set clock operation done signal for next task*/
+#define TIMESYNC_FW_SIG_PNFW_OFFSET 0x845C
+
+/*Set clock operation done signal for next task*/
+#define TIMESYNC_FW_SIG_TIMESYNCFW_OFFSET 0x8460
+
+/*New list is copied at this time*/
+#define TAS_CONFIG_CHANGE_TIME 0x000C
+
+/*config change error counter*/
+#define TAS_CONFIG_CHANGE_ERROR_COUNTER 0x0014
+
+/*TAS List update pending flag*/
+#define TAS_CONFIG_PENDING 0x0018
+
+/*TAS list update trigger flag*/
+#define TAS_CONFIG_CHANGE 0x0019
+
+/*List length for new TAS schedule*/
+#define TAS_ADMIN_LIST_LENGTH 0x001A
+
+/*Currently active TAS list index*/
+#define TAS_ACTIVE_LIST_INDEX 0x001B
+
+/*Cycle time for the new TAS schedule*/
+#define TAS_ADMIN_CYCLE_TIME 0x001C
+
+/*Cycle counts remaining till the TAS list update*/
+#define TAS_CONFIG_CHANGE_CYCLE_COUNT 0x0020
+
+/*Base Flow ID for sending packets to Host for Slice0*/
+#define PSI_L_REGULAR_FLOW_ID_BASE_OFFSET 0x0024
+
+/*Same as PSI_L_REGULAR_FLOW_ID_BASE_OFFSET*/
+#define EMAC_ICSSG_SWITCH_PSI_L_REGULAR_FLOW_ID_BASE_OFFSET PSI_L_REGULAR_FLOW_ID_BASE_OFFSET
+
+/*Base Flow ID for sending mgmt and Tx TS to Host for Slice0*/
+#define PSI_L_MGMT_FLOW_ID_OFFSET 0x0026
+
+/*Same as PSI_L_MGMT_FLOW_ID_OFFSET*/
+#define EMAC_ICSSG_SWITCH_PSI_L_MGMT_FLOW_ID_BASE_OFFSET PSI_L_MGMT_FLOW_ID_OFFSET
+
+/*Queue number for Special packets written here*/
+#define SPL_PKT_DEFAULT_PRIORITY 0x0028
+
+/*Express Preemptible Queue Mask*/
+#define EXPRESS_PRE_EMPTIVE_Q_MASK 0x0029
+
+/*Port1/Port2 Default Queue number for untagged packets, only 1B is used*/
+#define QUEUE_NUM_UNTAGGED 0x002A
+
+/*Stores the table used for priority regeneration. 1B per PCP/Queue*/
+#define PORT_Q_PRIORITY_REGEN_OFFSET 0x002C
+
+/* For marking Packet as priority/express (this feature is disabled) or
+ * cut-through/S&F.
+ */
+#define EXPRESS_PRE_EMPTIVE_Q_MAP 0x0034
+
+/*Stores the table used for priority mapping. 1B per PCP/Queue*/
+#define PORT_Q_PRIORITY_MAPPING_OFFSET 0x003C
+
+/*TAS gate mask for windows list0*/
+#define TAS_GATE_MASK_LIST0 0x0100
+
+/*TAS gate mask for windows list1*/
+#define TAS_GATE_MASK_LIST1 0x0350
+
+/*Memory to Enable/Disable Preemption on TX side*/
+#define PRE_EMPTION_ENABLE_TX 0x05A0
+
+/*Active State of Preemption on TX side*/
+#define PRE_EMPTION_ACTIVE_TX 0x05A1
+
+/*Memory to Enable/Disable Verify State Machine Preemption*/
+#define PRE_EMPTION_ENABLE_VERIFY 0x05A2
+
+/*Verify Status of State Machine*/
+#define PRE_EMPTION_VERIFY_STATUS 0x05A3
+
+/*Non Final Fragment Size supported by Link Partner*/
+#define PRE_EMPTION_ADD_FRAG_SIZE_REMOTE 0x05A4
+
+/*Non Final Fragment Size supported by Firmware*/
+#define PRE_EMPTION_ADD_FRAG_SIZE_LOCAL 0x05A6
+
+/*Time in ms the State machine waits for respond packet*/
+#define PRE_EMPTION_VERIFY_TIME 0x05A8
+
+/*Memory used for R30 related management commands*/
+#define MGR_R30_CMD_OFFSET 0x05AC
+
+/*HW Buffer Pool0 base address*/
+#define BUFFER_POOL_0_ADDR_OFFSET 0x05BC
+
+/*16B for Host Egress MSMC Q (Pre-emptible) context*/
+#define HOST_RX_Q_PRE_CONTEXT_OFFSET 0x0684
+
+/*Buffer for 8 FDB entries to be added by 'Add Multiple FDB entries IOCTL*/
+#define FDB_CMD_BUFFER 0x0894
+
+/*16B for Host Egress MSMC Q (Express) context*/
+#define HOST_RX_Q_EXP_CONTEXT_OFFSET 0x0940
+
+/*Start of 32 bits PA_STAT counters*/
+#define PA_STAT_32b_START_OFFSET 0x0080
+
+#endif
+/* __NET_TI_ICSSG_SWITCH_MAP_H */
Add firmware interface related headers and macros for ICSSG Ethernet driver. These macros will be later used by the ICSSG ethernet driver. Signed-off-by: MD Danish Anwar <danishanwar@ti.com> --- drivers/net/ti/icssg_switch_map.h | 209 ++++++++++++++++++++++++++++++ 1 file changed, 209 insertions(+) create mode 100644 drivers/net/ti/icssg_switch_map.h