@@ -18,8 +18,6 @@
ethernet0 = &cpsw_port1;
remoteproc0 = &sysctrler;
remoteproc1 = &a53_0;
- spi0 = &ospi0;
- spi1 = &ospi1;
usb0 = &usb0;
usb1 = &usb1;
};
@@ -111,22 +109,6 @@
AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */
>;
};
-
- mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
- pinctrl-single,pins = <
- AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
- AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* (U2) MCU_OSPI0_DQS */
- AM65X_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* (U4) MCU_OSPI0_D0 */
- AM65X_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* (U5) MCU_OSPI0_D1 */
- AM65X_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* (T2) MCU_OSPI0_D2 */
- AM65X_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* (T3) MCU_OSPI0_D3 */
- AM65X_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* (T4) MCU_OSPI0_D4 */
- AM65X_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* (T5) MCU_OSPI0_D5 */
- AM65X_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* (R2) MCU_OSPI0_D6 */
- AM65X_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* (R3) MCU_OSPI0_D7 */
- AM65X_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* (R4) MCU_OSPI0_CSn0 */
- >;
- };
};
&main_pmx0 {
@@ -170,27 +152,8 @@
};
&ospi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
- bootph-pre-ram;
-
reg = <0x0 0x47040000 0x0 0x100>,
<0x0 0x50000000 0x0 0x8000000>;
-
- flash@0{
- compatible = "jedec,spi-nor";
- reg = <0x0>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <8>;
- spi-max-frequency = <50000000>;
- cdns,tshsl-ns = <60>;
- cdns,tsd2d-ns = <60>;
- cdns,tchsh-ns = <60>;
- cdns,tslch-ns = <60>;
- cdns,read-delay = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
};
&main_pmx0 {
With the Linux and U-Boot board dtb files unified, we now have a duplicate ospi0 node. Remove it Signed-off-by: Bryan Brattlof <bb@ti.com> --- arch/arm/dts/k3-am654-r5-base-board.dts | 37 ------------------------- 1 file changed, 37 deletions(-)