| Message ID | 20230419134014.128461-4-eugen.hristev@collabora.com |
|---|---|
| State | Superseded |
| Delegated to: | Kever Yang |
| Headers | show |
| Series | [v5,1/6] ARM: dts: rockchip: rk3588-rock-5b-u-boot: add USB 2.0 host | expand |
Hi Neil, Could you take a look at this patch? Thanks, - Kever On 2023/4/19 21:40, Eugen Hristev wrote: > phy-supply is now handled at uclass level. Remove it from the drivers that > implement it at the driver level. > > Suggested-by: Jonas Karlman <jonas@kwiboo.se> > Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> > --- > drivers/phy/meson-g12a-usb2.c | 48 ----------------------------------- > drivers/phy/meson-gxbb-usb2.c | 38 --------------------------- > drivers/phy/meson-gxl-usb2.c | 30 ---------------------- > 3 files changed, 116 deletions(-) > > diff --git a/drivers/phy/meson-g12a-usb2.c b/drivers/phy/meson-g12a-usb2.c > index 2fbba7fdae01..650b88bd1803 100644 > --- a/drivers/phy/meson-g12a-usb2.c > +++ b/drivers/phy/meson-g12a-usb2.c > @@ -54,50 +54,12 @@ > > struct phy_meson_g12a_usb2_priv { > struct regmap *regmap; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > #if CONFIG_IS_ENABLED(CLK) > struct clk clk; > #endif > struct reset_ctl reset; > }; > > - > -static int phy_meson_g12a_usb2_power_on(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - if (ret) > - return ret; > - } > -#endif > - > - return 0; > -} > - > -static int phy_meson_g12a_usb2_power_off(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - if (ret) { > - pr_err("Error disabling PHY supply\n"); > - return ret; > - } > - } > -#endif > - > - return 0; > -} > - > static int phy_meson_g12a_usb2_init(struct phy *phy) > { > struct udevice *dev = phy->dev; > @@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy) > struct phy_ops meson_g12a_usb2_phy_ops = { > .init = phy_meson_g12a_usb2_init, > .exit = phy_meson_g12a_usb2_exit, > - .power_on = phy_meson_g12a_usb2_power_on, > - .power_off = phy_meson_g12a_usb2_power_off, > }; > > int meson_g12a_usb2_phy_probe(struct udevice *dev) > @@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev) > } > #endif > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > - > return 0; > } > > diff --git a/drivers/phy/meson-gxbb-usb2.c b/drivers/phy/meson-gxbb-usb2.c > index 7a2e3d2739e8..70a80b863819 100644 > --- a/drivers/phy/meson-gxbb-usb2.c > +++ b/drivers/phy/meson-gxbb-usb2.c > @@ -12,7 +12,6 @@ > #include <clk.h> > #include <dm.h> > #include <generic-phy.h> > -#include <power/regulator.h> > #include <regmap.h> > #include <reset.h> > #include <linux/bitops.h> > @@ -81,9 +80,6 @@ > struct phy_meson_gxbb_usb2_priv { > struct regmap *regmap; > struct reset_ctl_bulk resets; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > }; > > static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > @@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); > uint val; > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - > - if (ret) > - return ret; > - } > -#endif > - > regmap_update_bits(priv->regmap, REG_CONFIG, > REG_CONFIG_CLK_32k_ALTSEL, > REG_CONFIG_CLK_32k_ALTSEL); > @@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > return 0; > } > > -static int phy_meson_gxbb_usb2_power_off(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - > - if (ret) > - return ret; > - } > -#endif > - > - return 0; > -} > - > static struct phy_ops meson_gxbb_usb2_phy_ops = { > .power_on = phy_meson_gxbb_usb2_power_on, > - .power_off = phy_meson_gxbb_usb2_power_off, > }; > > static int meson_gxbb_usb2_phy_probe(struct udevice *dev) > @@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev) > return ret; > } > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > ret = reset_get_bulk(dev, &priv->resets); > if (!ret) { > ret = reset_deassert_bulk(&priv->resets); > diff --git a/drivers/phy/meson-gxl-usb2.c b/drivers/phy/meson-gxl-usb2.c > index 9fb376cec448..4c631310efac 100644 > --- a/drivers/phy/meson-gxl-usb2.c > +++ b/drivers/phy/meson-gxl-usb2.c > @@ -16,7 +16,6 @@ > #include <generic-phy.h> > #include <regmap.h> > #include <linux/delay.h> > -#include <power/regulator.h> > #include <clk.h> > #include <linux/usb/otg.h> > > @@ -101,9 +100,6 @@ > > struct phy_meson_gxl_usb2_priv { > struct regmap *regmap; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > #if CONFIG_IS_ENABLED(CLK) > struct clk clk; > #endif > @@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy) > > phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST); > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - if (ret) > - return ret; > - } > -#endif > - > return 0; > } > > @@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy) > val |= U2P_R0_POWER_ON_RESET; > regmap_write(priv->regmap, U2P_R0, val); > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - if (ret) { > - pr_err("Error disabling PHY supply\n"); > - return ret; > - } > - } > -#endif > - > return 0; > } > > @@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev) > } > #endif > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > - > return 0; > } >
On 19/04/2023 15:40, Eugen Hristev wrote: > phy-supply is now handled at uclass level. Remove it from the drivers that > implement it at the driver level. > > Suggested-by: Jonas Karlman <jonas@kwiboo.se> > Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> > --- > drivers/phy/meson-g12a-usb2.c | 48 ----------------------------------- > drivers/phy/meson-gxbb-usb2.c | 38 --------------------------- > drivers/phy/meson-gxl-usb2.c | 30 ---------------------- > 3 files changed, 116 deletions(-) > > diff --git a/drivers/phy/meson-g12a-usb2.c b/drivers/phy/meson-g12a-usb2.c > index 2fbba7fdae01..650b88bd1803 100644 > --- a/drivers/phy/meson-g12a-usb2.c > +++ b/drivers/phy/meson-g12a-usb2.c > @@ -54,50 +54,12 @@ > > struct phy_meson_g12a_usb2_priv { > struct regmap *regmap; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > #if CONFIG_IS_ENABLED(CLK) > struct clk clk; > #endif > struct reset_ctl reset; > }; > > - > -static int phy_meson_g12a_usb2_power_on(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - if (ret) > - return ret; > - } > -#endif > - > - return 0; > -} > - > -static int phy_meson_g12a_usb2_power_off(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - if (ret) { > - pr_err("Error disabling PHY supply\n"); > - return ret; > - } > - } > -#endif > - > - return 0; > -} > - > static int phy_meson_g12a_usb2_init(struct phy *phy) > { > struct udevice *dev = phy->dev; > @@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy) > struct phy_ops meson_g12a_usb2_phy_ops = { > .init = phy_meson_g12a_usb2_init, > .exit = phy_meson_g12a_usb2_exit, > - .power_on = phy_meson_g12a_usb2_power_on, > - .power_off = phy_meson_g12a_usb2_power_off, > }; > > int meson_g12a_usb2_phy_probe(struct udevice *dev) > @@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev) > } > #endif > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > - > return 0; > } > > diff --git a/drivers/phy/meson-gxbb-usb2.c b/drivers/phy/meson-gxbb-usb2.c > index 7a2e3d2739e8..70a80b863819 100644 > --- a/drivers/phy/meson-gxbb-usb2.c > +++ b/drivers/phy/meson-gxbb-usb2.c > @@ -12,7 +12,6 @@ > #include <clk.h> > #include <dm.h> > #include <generic-phy.h> > -#include <power/regulator.h> > #include <regmap.h> > #include <reset.h> > #include <linux/bitops.h> > @@ -81,9 +80,6 @@ > struct phy_meson_gxbb_usb2_priv { > struct regmap *regmap; > struct reset_ctl_bulk resets; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > }; > > static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > @@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); > uint val; > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - > - if (ret) > - return ret; > - } > -#endif > - > regmap_update_bits(priv->regmap, REG_CONFIG, > REG_CONFIG_CLK_32k_ALTSEL, > REG_CONFIG_CLK_32k_ALTSEL); > @@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) > return 0; > } > > -static int phy_meson_gxbb_usb2_power_off(struct phy *phy) > -{ > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *dev = phy->dev; > - struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); > - > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - > - if (ret) > - return ret; > - } > -#endif > - > - return 0; > -} > - > static struct phy_ops meson_gxbb_usb2_phy_ops = { > .power_on = phy_meson_gxbb_usb2_power_on, > - .power_off = phy_meson_gxbb_usb2_power_off, > }; > > static int meson_gxbb_usb2_phy_probe(struct udevice *dev) > @@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev) > return ret; > } > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > ret = reset_get_bulk(dev, &priv->resets); > if (!ret) { > ret = reset_deassert_bulk(&priv->resets); > diff --git a/drivers/phy/meson-gxl-usb2.c b/drivers/phy/meson-gxl-usb2.c > index 9fb376cec448..4c631310efac 100644 > --- a/drivers/phy/meson-gxl-usb2.c > +++ b/drivers/phy/meson-gxl-usb2.c > @@ -16,7 +16,6 @@ > #include <generic-phy.h> > #include <regmap.h> > #include <linux/delay.h> > -#include <power/regulator.h> > #include <clk.h> > #include <linux/usb/otg.h> > > @@ -101,9 +100,6 @@ > > struct phy_meson_gxl_usb2_priv { > struct regmap *regmap; > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - struct udevice *phy_supply; > -#endif > #if CONFIG_IS_ENABLED(CLK) > struct clk clk; > #endif > @@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy) > > phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST); > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, true); > - if (ret) > - return ret; > - } > -#endif > - > return 0; > } > > @@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy) > val |= U2P_R0_POWER_ON_RESET; > regmap_write(priv->regmap, U2P_R0, val); > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - if (priv->phy_supply) { > - int ret = regulator_set_enable(priv->phy_supply, false); > - if (ret) { > - pr_err("Error disabling PHY supply\n"); > - return ret; > - } > - } > -#endif > - > return 0; > } > > @@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev) > } > #endif > > -#if CONFIG_IS_ENABLED(DM_REGULATOR) > - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); > - if (ret && ret != -ENOENT) { > - pr_err("Failed to get PHY regulator\n"); > - return ret; > - } > -#endif > - > return 0; > } > Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
diff --git a/drivers/phy/meson-g12a-usb2.c b/drivers/phy/meson-g12a-usb2.c index 2fbba7fdae01..650b88bd1803 100644 --- a/drivers/phy/meson-g12a-usb2.c +++ b/drivers/phy/meson-g12a-usb2.c @@ -54,50 +54,12 @@ struct phy_meson_g12a_usb2_priv { struct regmap *regmap; -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *phy_supply; -#endif #if CONFIG_IS_ENABLED(CLK) struct clk clk; #endif struct reset_ctl reset; }; - -static int phy_meson_g12a_usb2_power_on(struct phy *phy) -{ -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *dev = phy->dev; - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); - - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, true); - if (ret) - return ret; - } -#endif - - return 0; -} - -static int phy_meson_g12a_usb2_power_off(struct phy *phy) -{ -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *dev = phy->dev; - struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev); - - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, false); - if (ret) { - pr_err("Error disabling PHY supply\n"); - return ret; - } - } -#endif - - return 0; -} - static int phy_meson_g12a_usb2_init(struct phy *phy) { struct udevice *dev = phy->dev; @@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy) struct phy_ops meson_g12a_usb2_phy_ops = { .init = phy_meson_g12a_usb2_init, .exit = phy_meson_g12a_usb2_exit, - .power_on = phy_meson_g12a_usb2_power_on, - .power_off = phy_meson_g12a_usb2_power_off, }; int meson_g12a_usb2_phy_probe(struct udevice *dev) @@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev) } #endif -#if CONFIG_IS_ENABLED(DM_REGULATOR) - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); - if (ret && ret != -ENOENT) { - pr_err("Failed to get PHY regulator\n"); - return ret; - } -#endif - return 0; } diff --git a/drivers/phy/meson-gxbb-usb2.c b/drivers/phy/meson-gxbb-usb2.c index 7a2e3d2739e8..70a80b863819 100644 --- a/drivers/phy/meson-gxbb-usb2.c +++ b/drivers/phy/meson-gxbb-usb2.c @@ -12,7 +12,6 @@ #include <clk.h> #include <dm.h> #include <generic-phy.h> -#include <power/regulator.h> #include <regmap.h> #include <reset.h> #include <linux/bitops.h> @@ -81,9 +80,6 @@ struct phy_meson_gxbb_usb2_priv { struct regmap *regmap; struct reset_ctl_bulk resets; -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *phy_supply; -#endif }; static int phy_meson_gxbb_usb2_power_on(struct phy *phy) @@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); uint val; -#if CONFIG_IS_ENABLED(DM_REGULATOR) - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, true); - - if (ret) - return ret; - } -#endif - regmap_update_bits(priv->regmap, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL, REG_CONFIG_CLK_32k_ALTSEL); @@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy) return 0; } -static int phy_meson_gxbb_usb2_power_off(struct phy *phy) -{ -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *dev = phy->dev; - struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev); - - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, false); - - if (ret) - return ret; - } -#endif - - return 0; -} - static struct phy_ops meson_gxbb_usb2_phy_ops = { .power_on = phy_meson_gxbb_usb2_power_on, - .power_off = phy_meson_gxbb_usb2_power_off, }; static int meson_gxbb_usb2_phy_probe(struct udevice *dev) @@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev) return ret; } -#if CONFIG_IS_ENABLED(DM_REGULATOR) - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); - if (ret && ret != -ENOENT) { - pr_err("Failed to get PHY regulator\n"); - return ret; - } -#endif ret = reset_get_bulk(dev, &priv->resets); if (!ret) { ret = reset_deassert_bulk(&priv->resets); diff --git a/drivers/phy/meson-gxl-usb2.c b/drivers/phy/meson-gxl-usb2.c index 9fb376cec448..4c631310efac 100644 --- a/drivers/phy/meson-gxl-usb2.c +++ b/drivers/phy/meson-gxl-usb2.c @@ -16,7 +16,6 @@ #include <generic-phy.h> #include <regmap.h> #include <linux/delay.h> -#include <power/regulator.h> #include <clk.h> #include <linux/usb/otg.h> @@ -101,9 +100,6 @@ struct phy_meson_gxl_usb2_priv { struct regmap *regmap; -#if CONFIG_IS_ENABLED(DM_REGULATOR) - struct udevice *phy_supply; -#endif #if CONFIG_IS_ENABLED(CLK) struct clk clk; #endif @@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy) phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST); -#if CONFIG_IS_ENABLED(DM_REGULATOR) - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, true); - if (ret) - return ret; - } -#endif - return 0; } @@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy) val |= U2P_R0_POWER_ON_RESET; regmap_write(priv->regmap, U2P_R0, val); -#if CONFIG_IS_ENABLED(DM_REGULATOR) - if (priv->phy_supply) { - int ret = regulator_set_enable(priv->phy_supply, false); - if (ret) { - pr_err("Error disabling PHY supply\n"); - return ret; - } - } -#endif - return 0; } @@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev) } #endif -#if CONFIG_IS_ENABLED(DM_REGULATOR) - ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); - if (ret && ret != -ENOENT) { - pr_err("Failed to get PHY regulator\n"); - return ret; - } -#endif - return 0; }
phy-supply is now handled at uclass level. Remove it from the drivers that implement it at the driver level. Suggested-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> --- drivers/phy/meson-g12a-usb2.c | 48 ----------------------------------- drivers/phy/meson-gxbb-usb2.c | 38 --------------------------- drivers/phy/meson-gxl-usb2.c | 30 ---------------------- 3 files changed, 116 deletions(-)