| Message ID | 20211110054200.13371-1-qiangqing.zhang@nxp.com |
|---|---|
| State | Rejected |
| Delegated to: | Ramon Fried |
| Headers | show |
| Series | net: eqos: connect and config PHY from probe stage instead of starting EQOS | expand |
Hi, On 11/10/21 6:42 AM, Joakim Zhang wrote: > For EQOS ethernet, it will do phy_connect() and phy_config() when start > the ethernet (eqos_srart()), users need wait seconds for PHY auto negotiation s/eqos_srart()/eqos_start()/ > to complete when do tftp boot. > phy_config() > -> board_phy_config() > -> phydev->drv->config() // i.MX8MP/DXL use realtek PHY > -> rtl8211f_config() > -> genphy_config_aneg() > -> genphy_restart_aneg() // restart auto-nego, then need seconds to complete > > To avoid wasting time, we can move PHY connection and configuration from > eqos_start() to eqos_probe(). This patch also moves clock setting from > eqos_start() to eqos_probe() as MDIO access need CSR clock, there is no > function change. > > Tested-on: i.MX8MP & i.MX8DXL > > Before: > u-boot=> run netboot > Booting from net ... > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done > BOOTP broadcast 1 > DHCP client bound to address 10.193.102.192 (313 ms) > Using ethernet@30bf0000 device > TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 > After: > u-boot=> run netboot > Booting from net ... > BOOTP broadcast 1 > DHCP client bound to address 10.193.102.192 (454 ms) > Using ethernet@30bf0000 device > TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 > > Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> > --- > drivers/net/dwc_eth_qos.c | 132 +++++++++++++++++++------------------- > 1 file changed, 67 insertions(+), 65 deletions(-) > > diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c > index 585101804d..c1923fbe6b 100644 > --- a/drivers/net/dwc_eth_qos.c > +++ b/drivers/net/dwc_eth_qos.c > @@ -1045,20 +1045,6 @@ static int eqos_start(struct udevice *dev) > eqos->tx_desc_idx = 0; > eqos->rx_desc_idx = 0; > > - ret = eqos->config->ops->eqos_start_clks(dev); > - if (ret < 0) { > - pr_err("eqos_start_clks() failed: %d", ret); > - goto err; > - } > - > - ret = eqos->config->ops->eqos_start_resets(dev); > - if (ret < 0) { > - pr_err("eqos_start_resets() failed: %d", ret); > - goto err_stop_clks; > - } > - > - udelay(10); > - > eqos->reg_access_ok = true; => as clock is moved in probe... the line eqos->reg_access_ok = true should be also moved I think or reg_access_ok can be removed, as reg_access_ok is always one when eqos_write_hwaddr is called > > ret = wait_for_bit_le32(&eqos->dma_regs->mode, > @@ -1066,68 +1052,34 @@ static int eqos_start(struct udevice *dev) > eqos->config->swr_wait, false); > if (ret) { > pr_err("EQOS_DMA_MODE_SWR stuck"); > - goto err_stop_resets; > + goto err; > } > > ret = eqos->config->ops->eqos_calibrate_pads(dev); > if (ret < 0) { > pr_err("eqos_calibrate_pads() failed: %d", ret); > - goto err_stop_resets; > + goto err; > } > rate = eqos->config->ops->eqos_get_tick_clk_rate(dev); > > val = (rate / 1000000) - 1; > writel(val, &eqos->mac_regs->us_tic_counter); > > - /* > - * if PHY was already connected and configured, > - * don't need to reconnect/reconfigure again > - */ > - if (!eqos->phy) { > - int addr = -1; > -#ifdef CONFIG_DM_ETH_PHY > - addr = eth_phy_get_addr(dev); > -#endif > -#ifdef DWC_NET_PHYADDR > - addr = DWC_NET_PHYADDR; > -#endif > - eqos->phy = phy_connect(eqos->mii, addr, dev, > - eqos->config->interface(dev)); > - if (!eqos->phy) { > - pr_err("phy_connect() failed"); > - goto err_stop_resets; > - } > - > - if (eqos->max_speed) { > - ret = phy_set_supported(eqos->phy, eqos->max_speed); > - if (ret) { > - pr_err("phy_set_supported() failed: %d", ret); > - goto err_shutdown_phy; > - } > - } > - > - ret = phy_config(eqos->phy); > - if (ret < 0) { > - pr_err("phy_config() failed: %d", ret); > - goto err_shutdown_phy; > - } > - } > - > ret = phy_startup(eqos->phy); > if (ret < 0) { > pr_err("phy_startup() failed: %d", ret); > - goto err_shutdown_phy; > + goto err; > } > > if (!eqos->phy->link) { > pr_err("No link"); > - goto err_shutdown_phy; > + goto err; > } > > ret = eqos_adjust_link(dev); > if (ret < 0) { > pr_err("eqos_adjust_link() failed: %d", ret); > - goto err_shutdown_phy; > + goto err; > } > > /* Configure MTL */ > @@ -1356,12 +1308,6 @@ static int eqos_start(struct udevice *dev) > debug("%s: OK\n", __func__); > return 0; > > -err_shutdown_phy: > - phy_shutdown(eqos->phy); > -err_stop_resets: > - eqos->config->ops->eqos_stop_resets(dev); > -err_stop_clks: > - eqos->config->ops->eqos_stop_clks(dev); > err: > pr_err("FAILED: %d", ret); > return ret; > @@ -1412,12 +1358,6 @@ static void eqos_stop(struct udevice *dev) > clrbits_le32(&eqos->dma_regs->ch0_rx_control, > EQOS_DMA_CH0_RX_CONTROL_SR); > > - if (eqos->phy) { > - phy_shutdown(eqos->phy); > - } > - eqos->config->ops->eqos_stop_resets(dev); > - eqos->config->ops->eqos_stop_clks(dev); > - > debug("%s: OK\n", __func__); > } > > @@ -1888,9 +1828,65 @@ static int eqos_probe(struct udevice *dev) > eth_phy_set_mdio_bus(dev, eqos->mii); > #endif > > + ret = eqos->config->ops->eqos_start_clks(dev); > + if (ret < 0) { > + pr_err("eqos_start_clks() failed: %d", ret); > + goto err_unregister_mdio; > + } > + > + ret = eqos->config->ops->eqos_start_resets(dev); > + if (ret < 0) { > + pr_err("eqos_start_resets() failed: %d", ret); > + goto err_stop_clks; > + } > + > + udelay(10); > + > + /* > + * if PHY was already connected and configured, > + * don't need to reconnect/reconfigure again > + */ > + if (!eqos->phy) { this test can be remove I think because we have always eqos->phy = NULL in probe, PHY was can't be configured before probe and it should be done again after a remove... > + int addr = -1; > +#ifdef CONFIG_DM_ETH_PHY > + addr = eth_phy_get_addr(dev); > +#endif > +#ifdef DWC_NET_PHYADDR > + addr = DWC_NET_PHYADDR; > +#endif > + eqos->phy = phy_connect(eqos->mii, addr, dev, > + eqos->config->interface(dev)); > + if (!eqos->phy) { > + pr_err("phy_connect() failed"); > + goto err_stop_resets; > + } > + > + if (eqos->max_speed) { > + ret = phy_set_supported(eqos->phy, eqos->max_speed); > + if (ret) { > + pr_err("phy_set_supported() failed: %d", ret); > + goto err_shutdown_phy; > + } > + } > + > + ret = phy_config(eqos->phy); > + if (ret < 0) { > + pr_err("phy_config() failed: %d", ret); > + goto err_shutdown_phy; > + } > + } > + > debug("%s: OK\n", __func__); > return 0; > > +err_shutdown_phy: > + phy_shutdown(eqos->phy); > +err_stop_resets: > + eqos->config->ops->eqos_stop_resets(dev); > +err_stop_clks: > + eqos->config->ops->eqos_stop_clks(dev); > +err_unregister_mdio: > + mdio_unregister(eqos->mii); > err_free_mdio: > mdio_free(eqos->mii); > err_remove_resources_tegra: > @@ -1908,6 +1904,12 @@ static int eqos_remove(struct udevice *dev) > > debug("%s(dev=%p):\n", __func__, dev); > > + if (eqos->phy) { > + phy_shutdown(eqos->phy); > + } > + eqos->config->ops->eqos_stop_resets(dev); > + eqos->config->ops->eqos_stop_clks(dev); > + > mdio_unregister(eqos->mii); > mdio_free(eqos->mii); > eqos->config->ops->eqos_remove_resources(dev); Regards Patrick
Hi All For information Another patch from Marek will collide with this one => https://patchwork.ozlabs.org/project/uboot/patch/20211113022352.231762-1-marex@denx.de/ Patrice On 11/15/21 11:41 AM, Patrick DELAUNAY wrote: > Hi, > > On 11/10/21 6:42 AM, Joakim Zhang wrote: >> For EQOS ethernet, it will do phy_connect() and phy_config() when start >> the ethernet (eqos_srart()), users need wait seconds for PHY auto negotiation > > s/eqos_srart()/eqos_start()/ > > >> to complete when do tftp boot. >> phy_config() >> -> board_phy_config() >> -> phydev->drv->config() // i.MX8MP/DXL use realtek PHY >> -> rtl8211f_config() >> -> genphy_config_aneg() >> -> genphy_restart_aneg() // restart auto-nego, then need seconds to complete >> >> To avoid wasting time, we can move PHY connection and configuration from >> eqos_start() to eqos_probe(). This patch also moves clock setting from >> eqos_start() to eqos_probe() as MDIO access need CSR clock, there is no >> function change. >> >> Tested-on: i.MX8MP & i.MX8DXL >> >> Before: >> u-boot=> run netboot >> Booting from net ... >> ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done >> BOOTP broadcast 1 >> DHCP client bound to address 10.193.102.192 (313 ms) >> Using ethernet@30bf0000 device >> TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 >> After: >> u-boot=> run netboot >> Booting from net ... >> BOOTP broadcast 1 >> DHCP client bound to address 10.193.102.192 (454 ms) >> Using ethernet@30bf0000 device >> TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 >> >> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> >> --- >> drivers/net/dwc_eth_qos.c | 132 +++++++++++++++++++------------------- >> 1 file changed, 67 insertions(+), 65 deletions(-) >> >> diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c >> index 585101804d..c1923fbe6b 100644 >> --- a/drivers/net/dwc_eth_qos.c >> +++ b/drivers/net/dwc_eth_qos.c >> @@ -1045,20 +1045,6 @@ static int eqos_start(struct udevice *dev) >> eqos->tx_desc_idx = 0; >> eqos->rx_desc_idx = 0; >> - ret = eqos->config->ops->eqos_start_clks(dev); >> - if (ret < 0) { >> - pr_err("eqos_start_clks() failed: %d", ret); >> - goto err; >> - } >> - >> - ret = eqos->config->ops->eqos_start_resets(dev); >> - if (ret < 0) { >> - pr_err("eqos_start_resets() failed: %d", ret); >> - goto err_stop_clks; >> - } >> - >> - udelay(10); >> - >> eqos->reg_access_ok = true; > > => as clock is moved in probe... > > the line > eqos->reg_access_ok = true > should be also moved I think > > or reg_access_ok can be removed, as reg_access_ok is always one when eqos_write_hwaddr is called > >> ret = wait_for_bit_le32(&eqos->dma_regs->mode, >> @@ -1066,68 +1052,34 @@ static int eqos_start(struct udevice *dev) >> eqos->config->swr_wait, false); >> if (ret) { >> pr_err("EQOS_DMA_MODE_SWR stuck"); >> - goto err_stop_resets; >> + goto err; >> } >> ret = eqos->config->ops->eqos_calibrate_pads(dev); >> if (ret < 0) { >> pr_err("eqos_calibrate_pads() failed: %d", ret); >> - goto err_stop_resets; >> + goto err; >> } >> rate = eqos->config->ops->eqos_get_tick_clk_rate(dev); >> val = (rate / 1000000) - 1; >> writel(val, &eqos->mac_regs->us_tic_counter); >> - /* >> - * if PHY was already connected and configured, >> - * don't need to reconnect/reconfigure again >> - */ >> - if (!eqos->phy) { >> - int addr = -1; >> -#ifdef CONFIG_DM_ETH_PHY >> - addr = eth_phy_get_addr(dev); >> -#endif >> -#ifdef DWC_NET_PHYADDR >> - addr = DWC_NET_PHYADDR; >> -#endif >> - eqos->phy = phy_connect(eqos->mii, addr, dev, >> - eqos->config->interface(dev)); >> - if (!eqos->phy) { >> - pr_err("phy_connect() failed"); >> - goto err_stop_resets; >> - } >> - >> - if (eqos->max_speed) { >> - ret = phy_set_supported(eqos->phy, eqos->max_speed); >> - if (ret) { >> - pr_err("phy_set_supported() failed: %d", ret); >> - goto err_shutdown_phy; >> - } >> - } >> - >> - ret = phy_config(eqos->phy); >> - if (ret < 0) { >> - pr_err("phy_config() failed: %d", ret); >> - goto err_shutdown_phy; >> - } >> - } >> - >> ret = phy_startup(eqos->phy); >> if (ret < 0) { >> pr_err("phy_startup() failed: %d", ret); >> - goto err_shutdown_phy; >> + goto err; >> } >> if (!eqos->phy->link) { >> pr_err("No link"); >> - goto err_shutdown_phy; >> + goto err; >> } >> ret = eqos_adjust_link(dev); >> if (ret < 0) { >> pr_err("eqos_adjust_link() failed: %d", ret); >> - goto err_shutdown_phy; >> + goto err; >> } >> /* Configure MTL */ >> @@ -1356,12 +1308,6 @@ static int eqos_start(struct udevice *dev) >> debug("%s: OK\n", __func__); >> return 0; >> -err_shutdown_phy: >> - phy_shutdown(eqos->phy); >> -err_stop_resets: >> - eqos->config->ops->eqos_stop_resets(dev); >> -err_stop_clks: >> - eqos->config->ops->eqos_stop_clks(dev); >> err: >> pr_err("FAILED: %d", ret); >> return ret; >> @@ -1412,12 +1358,6 @@ static void eqos_stop(struct udevice *dev) >> clrbits_le32(&eqos->dma_regs->ch0_rx_control, >> EQOS_DMA_CH0_RX_CONTROL_SR); >> - if (eqos->phy) { >> - phy_shutdown(eqos->phy); >> - } >> - eqos->config->ops->eqos_stop_resets(dev); >> - eqos->config->ops->eqos_stop_clks(dev); >> - >> debug("%s: OK\n", __func__); >> } >> @@ -1888,9 +1828,65 @@ static int eqos_probe(struct udevice *dev) >> eth_phy_set_mdio_bus(dev, eqos->mii); >> #endif >> + ret = eqos->config->ops->eqos_start_clks(dev); >> + if (ret < 0) { >> + pr_err("eqos_start_clks() failed: %d", ret); >> + goto err_unregister_mdio; >> + } >> + >> + ret = eqos->config->ops->eqos_start_resets(dev); >> + if (ret < 0) { >> + pr_err("eqos_start_resets() failed: %d", ret); >> + goto err_stop_clks; >> + } >> + >> + udelay(10); >> + >> + /* >> + * if PHY was already connected and configured, >> + * don't need to reconnect/reconfigure again >> + */ >> + if (!eqos->phy) { > > > this test can be remove I think > > because we have always eqos->phy = NULL in probe, > > PHY was can't be configured before probe > > and it should be done again after a remove... > > >> + int addr = -1; >> +#ifdef CONFIG_DM_ETH_PHY >> + addr = eth_phy_get_addr(dev); >> +#endif >> +#ifdef DWC_NET_PHYADDR >> + addr = DWC_NET_PHYADDR; >> +#endif >> + eqos->phy = phy_connect(eqos->mii, addr, dev, >> + eqos->config->interface(dev)); >> + if (!eqos->phy) { >> + pr_err("phy_connect() failed"); >> + goto err_stop_resets; >> + } >> + >> + if (eqos->max_speed) { >> + ret = phy_set_supported(eqos->phy, eqos->max_speed); >> + if (ret) { >> + pr_err("phy_set_supported() failed: %d", ret); >> + goto err_shutdown_phy; >> + } >> + } >> + >> + ret = phy_config(eqos->phy); >> + if (ret < 0) { >> + pr_err("phy_config() failed: %d", ret); >> + goto err_shutdown_phy; >> + } >> + } >> + >> debug("%s: OK\n", __func__); >> return 0; >> +err_shutdown_phy: >> + phy_shutdown(eqos->phy); >> +err_stop_resets: >> + eqos->config->ops->eqos_stop_resets(dev); >> +err_stop_clks: >> + eqos->config->ops->eqos_stop_clks(dev); >> +err_unregister_mdio: >> + mdio_unregister(eqos->mii); >> err_free_mdio: >> mdio_free(eqos->mii); >> err_remove_resources_tegra: >> @@ -1908,6 +1904,12 @@ static int eqos_remove(struct udevice *dev) >> debug("%s(dev=%p):\n", __func__, dev); >> + if (eqos->phy) { >> + phy_shutdown(eqos->phy); >> + } >> + eqos->config->ops->eqos_stop_resets(dev); >> + eqos->config->ops->eqos_stop_clks(dev); >> + >> mdio_unregister(eqos->mii); >> mdio_free(eqos->mii); >> eqos->config->ops->eqos_remove_resources(dev); > > > Regards > > > Patrick >
On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang <qiangqing.zhang@nxp.com> wrote: > > For EQOS ethernet, it will do phy_connect() and phy_config() when start > the ethernet (eqos_srart()), users need wait seconds for PHY auto negotiation > to complete when do tftp boot. > phy_config() > -> board_phy_config() > -> phydev->drv->config() // i.MX8MP/DXL use realtek PHY > -> rtl8211f_config() > -> genphy_config_aneg() > -> genphy_restart_aneg() // restart auto-nego, then need seconds to complete > > To avoid wasting time, we can move PHY connection and configuration from > eqos_start() to eqos_probe(). This patch also moves clock setting from > eqos_start() to eqos_probe() as MDIO access need CSR clock, there is no > function change. > > Tested-on: i.MX8MP & i.MX8DXL > > Before: > u-boot=> run netboot > Booting from net ... > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done > BOOTP broadcast 1 > DHCP client bound to address 10.193.102.192 (313 ms) > Using ethernet@30bf0000 device > TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 > After: > u-boot=> run netboot > Booting from net ... > BOOTP broadcast 1 > DHCP client bound to address 10.193.102.192 (454 ms) > Using ethernet@30bf0000 device > TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 > How much time do you save exactly, Is it the ~140ms you show here at the commit log ? > Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> > --- > drivers/net/dwc_eth_qos.c | 132 +++++++++++++++++++------------------- > 1 file changed, 67 insertions(+), 65 deletions(-) > > diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c > index 585101804d..c1923fbe6b 100644 > --- a/drivers/net/dwc_eth_qos.c > +++ b/drivers/net/dwc_eth_qos.c > @@ -1045,20 +1045,6 @@ static int eqos_start(struct udevice *dev) > eqos->tx_desc_idx = 0; > eqos->rx_desc_idx = 0; > > - ret = eqos->config->ops->eqos_start_clks(dev); > - if (ret < 0) { > - pr_err("eqos_start_clks() failed: %d", ret); > - goto err; > - } > - > - ret = eqos->config->ops->eqos_start_resets(dev); > - if (ret < 0) { > - pr_err("eqos_start_resets() failed: %d", ret); > - goto err_stop_clks; > - } > - > - udelay(10); > - > eqos->reg_access_ok = true; > > ret = wait_for_bit_le32(&eqos->dma_regs->mode, > @@ -1066,68 +1052,34 @@ static int eqos_start(struct udevice *dev) > eqos->config->swr_wait, false); > if (ret) { > pr_err("EQOS_DMA_MODE_SWR stuck"); > - goto err_stop_resets; > + goto err; > } > > ret = eqos->config->ops->eqos_calibrate_pads(dev); > if (ret < 0) { > pr_err("eqos_calibrate_pads() failed: %d", ret); > - goto err_stop_resets; > + goto err; > } > rate = eqos->config->ops->eqos_get_tick_clk_rate(dev); > > val = (rate / 1000000) - 1; > writel(val, &eqos->mac_regs->us_tic_counter); > > - /* > - * if PHY was already connected and configured, > - * don't need to reconnect/reconfigure again > - */ > - if (!eqos->phy) { > - int addr = -1; > -#ifdef CONFIG_DM_ETH_PHY > - addr = eth_phy_get_addr(dev); > -#endif > -#ifdef DWC_NET_PHYADDR > - addr = DWC_NET_PHYADDR; > -#endif > - eqos->phy = phy_connect(eqos->mii, addr, dev, > - eqos->config->interface(dev)); > - if (!eqos->phy) { > - pr_err("phy_connect() failed"); > - goto err_stop_resets; > - } > - > - if (eqos->max_speed) { > - ret = phy_set_supported(eqos->phy, eqos->max_speed); > - if (ret) { > - pr_err("phy_set_supported() failed: %d", ret); > - goto err_shutdown_phy; > - } > - } > - > - ret = phy_config(eqos->phy); > - if (ret < 0) { > - pr_err("phy_config() failed: %d", ret); > - goto err_shutdown_phy; > - } > - } > - > ret = phy_startup(eqos->phy); > if (ret < 0) { > pr_err("phy_startup() failed: %d", ret); > - goto err_shutdown_phy; > + goto err; > } > > if (!eqos->phy->link) { > pr_err("No link"); > - goto err_shutdown_phy; > + goto err; > } > > ret = eqos_adjust_link(dev); > if (ret < 0) { > pr_err("eqos_adjust_link() failed: %d", ret); > - goto err_shutdown_phy; > + goto err; > } > > /* Configure MTL */ > @@ -1356,12 +1308,6 @@ static int eqos_start(struct udevice *dev) > debug("%s: OK\n", __func__); > return 0; > > -err_shutdown_phy: > - phy_shutdown(eqos->phy); > -err_stop_resets: > - eqos->config->ops->eqos_stop_resets(dev); > -err_stop_clks: > - eqos->config->ops->eqos_stop_clks(dev); > err: > pr_err("FAILED: %d", ret); > return ret; > @@ -1412,12 +1358,6 @@ static void eqos_stop(struct udevice *dev) > clrbits_le32(&eqos->dma_regs->ch0_rx_control, > EQOS_DMA_CH0_RX_CONTROL_SR); > > - if (eqos->phy) { > - phy_shutdown(eqos->phy); > - } > - eqos->config->ops->eqos_stop_resets(dev); > - eqos->config->ops->eqos_stop_clks(dev); > - > debug("%s: OK\n", __func__); > } > > @@ -1888,9 +1828,65 @@ static int eqos_probe(struct udevice *dev) > eth_phy_set_mdio_bus(dev, eqos->mii); > #endif > > + ret = eqos->config->ops->eqos_start_clks(dev); > + if (ret < 0) { > + pr_err("eqos_start_clks() failed: %d", ret); > + goto err_unregister_mdio; > + } > + > + ret = eqos->config->ops->eqos_start_resets(dev); > + if (ret < 0) { > + pr_err("eqos_start_resets() failed: %d", ret); > + goto err_stop_clks; > + } > + > + udelay(10); > + > + /* > + * if PHY was already connected and configured, > + * don't need to reconnect/reconfigure again > + */ > + if (!eqos->phy) { > + int addr = -1; > +#ifdef CONFIG_DM_ETH_PHY > + addr = eth_phy_get_addr(dev); > +#endif > +#ifdef DWC_NET_PHYADDR > + addr = DWC_NET_PHYADDR; > +#endif > + eqos->phy = phy_connect(eqos->mii, addr, dev, > + eqos->config->interface(dev)); > + if (!eqos->phy) { > + pr_err("phy_connect() failed"); > + goto err_stop_resets; > + } > + > + if (eqos->max_speed) { > + ret = phy_set_supported(eqos->phy, eqos->max_speed); > + if (ret) { > + pr_err("phy_set_supported() failed: %d", ret); > + goto err_shutdown_phy; > + } > + } > + > + ret = phy_config(eqos->phy); > + if (ret < 0) { > + pr_err("phy_config() failed: %d", ret); > + goto err_shutdown_phy; > + } > + } > + > debug("%s: OK\n", __func__); > return 0; > > +err_shutdown_phy: > + phy_shutdown(eqos->phy); > +err_stop_resets: > + eqos->config->ops->eqos_stop_resets(dev); > +err_stop_clks: > + eqos->config->ops->eqos_stop_clks(dev); > +err_unregister_mdio: > + mdio_unregister(eqos->mii); > err_free_mdio: > mdio_free(eqos->mii); > err_remove_resources_tegra: > @@ -1908,6 +1904,12 @@ static int eqos_remove(struct udevice *dev) > > debug("%s(dev=%p):\n", __func__, dev); > > + if (eqos->phy) { > + phy_shutdown(eqos->phy); > + } > + eqos->config->ops->eqos_stop_resets(dev); > + eqos->config->ops->eqos_stop_clks(dev); > + > mdio_unregister(eqos->mii); > mdio_free(eqos->mii); > eqos->config->ops->eqos_remove_resources(dev); > -- > 2.17.1 >
Hi Patrick, > -----Original Message----- > From: Patrick DELAUNAY <patrick.delaunay@foss.st.com> > Sent: 2021年11月15日 18:42 > To: Joakim Zhang <qiangqing.zhang@nxp.com>; joe.hershberger@ni.com; > rfried.dev@gmail.com > Cc: u-boot@lists.denx.de; Ye Li <ye.li@nxp.com>; daniil.stas@posteo.net; > swarren@nvidia.com; Christophe ROULLIER > <christophe.roullier@foss.st.com>; Marek Vasut <marex@denx.de> > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > instead of starting EQOS > > Hi, > > On 11/10/21 6:42 AM, Joakim Zhang wrote: > > For EQOS ethernet, it will do phy_connect() and phy_config() when > > start the ethernet (eqos_srart()), users need wait seconds for PHY > > auto negotiation > > s/eqos_srart()/eqos_start()/ > > > > to complete when do tftp boot. > > phy_config() > > -> board_phy_config() > > -> phydev->drv->config() // i.MX8MP/DXL use > realtek PHY > > -> rtl8211f_config() > > -> genphy_config_aneg() > > -> > genphy_restart_aneg() > > // restart auto-nego, then need seconds to complete > > > > To avoid wasting time, we can move PHY connection and configuration > > from > > eqos_start() to eqos_probe(). This patch also moves clock setting from > > eqos_start() to eqos_probe() as MDIO access need CSR clock, there is > > no function change. > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > Before: > > u-boot=> run netboot > > Booting from net ... > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > 10.193.108.176; our IP address is 10.193.102.192; sending through > > gateway 10.193.102.254 > > After: > > u-boot=> run netboot > > Booting from net ... > > BOOTP broadcast 1 > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP > > address is 10.193.102.192; sending through gateway 10.193.102.254 > > > > Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> > > --- > > drivers/net/dwc_eth_qos.c | 132 > +++++++++++++++++++------------------- > > 1 file changed, 67 insertions(+), 65 deletions(-) > > > > diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c > > index 585101804d..c1923fbe6b 100644 > > --- a/drivers/net/dwc_eth_qos.c > > +++ b/drivers/net/dwc_eth_qos.c > > @@ -1045,20 +1045,6 @@ static int eqos_start(struct udevice *dev) > > eqos->tx_desc_idx = 0; > > eqos->rx_desc_idx = 0; > > > > - ret = eqos->config->ops->eqos_start_clks(dev); > > - if (ret < 0) { > > - pr_err("eqos_start_clks() failed: %d", ret); > > - goto err; > > - } > > - > > - ret = eqos->config->ops->eqos_start_resets(dev); > > - if (ret < 0) { > > - pr_err("eqos_start_resets() failed: %d", ret); > > - goto err_stop_clks; > > - } > > - > > - udelay(10); > > - > > eqos->reg_access_ok = true; > > => as clock is moved in probe... > > the line > eqos->reg_access_ok = true > should be also moved I think > > or reg_access_ok can be removed, as reg_access_ok is always one when > eqos_write_hwaddr is called Why? I saw this variable "reg_access_ok " doesn't have initialize value. If remove this line, I think it will break the logic in eqos_write_hwaddr(), so I agree also move it into probe(). > > > > ret = wait_for_bit_le32(&eqos->dma_regs->mode, > > @@ -1066,68 +1052,34 @@ static int eqos_start(struct udevice *dev) > > eqos->config->swr_wait, false); > > if (ret) { > > pr_err("EQOS_DMA_MODE_SWR stuck"); > > - goto err_stop_resets; > > + goto err; > > } > > > > ret = eqos->config->ops->eqos_calibrate_pads(dev); > > if (ret < 0) { > > pr_err("eqos_calibrate_pads() failed: %d", ret); > > - goto err_stop_resets; > > + goto err; > > } > > rate = eqos->config->ops->eqos_get_tick_clk_rate(dev); > > > > val = (rate / 1000000) - 1; > > writel(val, &eqos->mac_regs->us_tic_counter); > > > > - /* > > - * if PHY was already connected and configured, > > - * don't need to reconnect/reconfigure again > > - */ > > - if (!eqos->phy) { > > - int addr = -1; > > -#ifdef CONFIG_DM_ETH_PHY > > - addr = eth_phy_get_addr(dev); > > -#endif > > -#ifdef DWC_NET_PHYADDR > > - addr = DWC_NET_PHYADDR; > > -#endif > > - eqos->phy = phy_connect(eqos->mii, addr, dev, > > - eqos->config->interface(dev)); > > - if (!eqos->phy) { > > - pr_err("phy_connect() failed"); > > - goto err_stop_resets; > > - } > > - > > - if (eqos->max_speed) { > > - ret = phy_set_supported(eqos->phy, eqos->max_speed); > > - if (ret) { > > - pr_err("phy_set_supported() failed: %d", ret); > > - goto err_shutdown_phy; > > - } > > - } > > - > > - ret = phy_config(eqos->phy); > > - if (ret < 0) { > > - pr_err("phy_config() failed: %d", ret); > > - goto err_shutdown_phy; > > - } > > - } > > - > > ret = phy_startup(eqos->phy); > > if (ret < 0) { > > pr_err("phy_startup() failed: %d", ret); > > - goto err_shutdown_phy; > > + goto err; > > } > > > > if (!eqos->phy->link) { > > pr_err("No link"); > > - goto err_shutdown_phy; > > + goto err; > > } > > > > ret = eqos_adjust_link(dev); > > if (ret < 0) { > > pr_err("eqos_adjust_link() failed: %d", ret); > > - goto err_shutdown_phy; > > + goto err; > > } > > > > /* Configure MTL */ > > @@ -1356,12 +1308,6 @@ static int eqos_start(struct udevice *dev) > > debug("%s: OK\n", __func__); > > return 0; > > > > -err_shutdown_phy: > > - phy_shutdown(eqos->phy); > > -err_stop_resets: > > - eqos->config->ops->eqos_stop_resets(dev); > > -err_stop_clks: > > - eqos->config->ops->eqos_stop_clks(dev); > > err: > > pr_err("FAILED: %d", ret); > > return ret; > > @@ -1412,12 +1358,6 @@ static void eqos_stop(struct udevice *dev) > > clrbits_le32(&eqos->dma_regs->ch0_rx_control, > > EQOS_DMA_CH0_RX_CONTROL_SR); > > > > - if (eqos->phy) { > > - phy_shutdown(eqos->phy); > > - } > > - eqos->config->ops->eqos_stop_resets(dev); > > - eqos->config->ops->eqos_stop_clks(dev); > > - > > debug("%s: OK\n", __func__); > > } > > > > @@ -1888,9 +1828,65 @@ static int eqos_probe(struct udevice *dev) > > eth_phy_set_mdio_bus(dev, eqos->mii); > > #endif > > > > + ret = eqos->config->ops->eqos_start_clks(dev); > > + if (ret < 0) { > > + pr_err("eqos_start_clks() failed: %d", ret); > > + goto err_unregister_mdio; > > + } > > + > > + ret = eqos->config->ops->eqos_start_resets(dev); > > + if (ret < 0) { > > + pr_err("eqos_start_resets() failed: %d", ret); > > + goto err_stop_clks; > > + } > > + > > + udelay(10); > > + > > + /* > > + * if PHY was already connected and configured, > > + * don't need to reconnect/reconfigure again > > + */ > > + if (!eqos->phy) { > > > this test can be remove I think > > because we have always eqos->phy = NULL in probe, > > PHY was can't be configured before probe > > and it should be done again after a remove... Agree, I will remove this check. Best Regards, Joakim Zhang > > > + int addr = -1; > > +#ifdef CONFIG_DM_ETH_PHY > > + addr = eth_phy_get_addr(dev); > > +#endif > > +#ifdef DWC_NET_PHYADDR > > + addr = DWC_NET_PHYADDR; > > +#endif > > + eqos->phy = phy_connect(eqos->mii, addr, dev, > > + eqos->config->interface(dev)); > > + if (!eqos->phy) { > > + pr_err("phy_connect() failed"); > > + goto err_stop_resets; > > + } > > + > > + if (eqos->max_speed) { > > + ret = phy_set_supported(eqos->phy, eqos->max_speed); > > + if (ret) { > > + pr_err("phy_set_supported() failed: %d", ret); > > + goto err_shutdown_phy; > > + } > > + } > > + > > + ret = phy_config(eqos->phy); > > + if (ret < 0) { > > + pr_err("phy_config() failed: %d", ret); > > + goto err_shutdown_phy; > > + } > > + } > > + > > debug("%s: OK\n", __func__); > > return 0; > > > > +err_shutdown_phy: > > + phy_shutdown(eqos->phy); > > +err_stop_resets: > > + eqos->config->ops->eqos_stop_resets(dev); > > +err_stop_clks: > > + eqos->config->ops->eqos_stop_clks(dev); > > +err_unregister_mdio: > > + mdio_unregister(eqos->mii); > > err_free_mdio: > > mdio_free(eqos->mii); > > err_remove_resources_tegra: > > @@ -1908,6 +1904,12 @@ static int eqos_remove(struct udevice *dev) > > > > debug("%s(dev=%p):\n", __func__, dev); > > > > + if (eqos->phy) { > > + phy_shutdown(eqos->phy); > > + } > > + eqos->config->ops->eqos_stop_resets(dev); > > + eqos->config->ops->eqos_stop_clks(dev); > > + > > mdio_unregister(eqos->mii); > > mdio_free(eqos->mii); > > eqos->config->ops->eqos_remove_resources(dev); > > > Regards > > > Patrick
Hi Ramon, > -----Original Message----- > From: Ramon Fried <rfried.dev@gmail.com> > Sent: 2021年11月16日 13:57 > To: Joakim Zhang <qiangqing.zhang@nxp.com> > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > <patrick.delaunay@foss.st.com>; Daniil Stas <daniil.stas@posteo.net>; > Stephen Warren <swarren@nvidia.com> > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > instead of starting EQOS > > On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang <qiangqing.zhang@nxp.com> > wrote: > > > > For EQOS ethernet, it will do phy_connect() and phy_config() when > > start the ethernet (eqos_srart()), users need wait seconds for PHY > > auto negotiation to complete when do tftp boot. > > phy_config() > > -> board_phy_config() > > -> phydev->drv->config() // i.MX8MP/DXL use > realtek PHY > > -> rtl8211f_config() > > -> genphy_config_aneg() > > -> > genphy_restart_aneg() > > // restart auto-nego, then need seconds to complete > > > > To avoid wasting time, we can move PHY connection and configuration > > from > > eqos_start() to eqos_probe(). This patch also moves clock setting from > > eqos_start() to eqos_probe() as MDIO access need CSR clock, there is > > no function change. > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > Before: > > u-boot=> run netboot > > Booting from net ... > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > 10.193.108.176; our IP address is 10.193.102.192; sending through > > gateway 10.193.102.254 > > After: > > u-boot=> run netboot > > Booting from net ... > > BOOTP broadcast 1 > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP > > address is 10.193.102.192; sending through gateway 10.193.102.254 > > > How much time do you save exactly, Is it the ~140ms you show here at the > commit log ? Exactly not. This time points to DHCP client bound to address, not the time this patch saves. How can we evaluate the time we save? Please see the log: Before: Booting from net ... ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done BOOTP broadcast 1 After: Booting from net ... BOOTP broadcast 1 And you need to check the related code: drivers/net/dwc_eth_qos.c: phy_startup ->...-> drivers/net/phy/phy.c: genphy_update_link() https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/net/phy/phy.c#L225 while (!(mii_reg & BMSR_ANEGCOMPLETE)) { /* * Timeout reached ? */ if (i > (PHY_ANEG_TIMEOUT / 50)) { printf(" TIMEOUT !\n"); phydev->link = 0; return -ETIMEDOUT; } if (ctrlc()) { puts("user interrupt!\n"); phydev->link = 0; return -EINTR; } if ((i++ % 10) == 0) printf("."); mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); mdelay(50); /* 50 ms */ } We can see that one "." is about 500ms, so from the log, we save about 500*7=3500ms=3.5s, this also means that PHY needs about 3.5s to complete auto-nego. I also described this in the commit message, "users need wait seconds for PHY auto negotiation to complete when do tftp boot", may not quite clear, I will improve it. Best Regards, Joakim Zhang
On Tue, Nov 16, 2021 at 10:04 AM Joakim Zhang <qiangqing.zhang@nxp.com> wrote: > > > Hi Ramon, > > > -----Original Message----- > > From: Ramon Fried <rfried.dev@gmail.com> > > Sent: 2021年11月16日 13:57 > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > > <patrick.delaunay@foss.st.com>; Daniil Stas <daniil.stas@posteo.net>; > > Stephen Warren <swarren@nvidia.com> > > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > > instead of starting EQOS > > > > On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang <qiangqing.zhang@nxp.com> > > wrote: > > > > > > For EQOS ethernet, it will do phy_connect() and phy_config() when > > > start the ethernet (eqos_srart()), users need wait seconds for PHY > > > auto negotiation to complete when do tftp boot. > > > phy_config() > > > -> board_phy_config() > > > -> phydev->drv->config() // i.MX8MP/DXL use > > realtek PHY > > > -> rtl8211f_config() > > > -> genphy_config_aneg() > > > -> > > genphy_restart_aneg() > > > // restart auto-nego, then need seconds to complete > > > > > > To avoid wasting time, we can move PHY connection and configuration > > > from > > > eqos_start() to eqos_probe(). This patch also moves clock setting from > > > eqos_start() to eqos_probe() as MDIO access need CSR clock, there is > > > no function change. > > > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > > > Before: > > > u-boot=> run netboot > > > Booting from net ... > > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > > done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 > > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > > 10.193.108.176; our IP address is 10.193.102.192; sending through > > > gateway 10.193.102.254 > > > After: > > > u-boot=> run netboot > > > Booting from net ... > > > BOOTP broadcast 1 > > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP > > > address is 10.193.102.192; sending through gateway 10.193.102.254 > > > > > How much time do you save exactly, Is it the ~140ms you show here at the > > commit log ? > > Exactly not. This time points to DHCP client bound to address, not the time this patch saves. > > How can we evaluate the time we save? Please see the log: > > Before: > Booting from net ... > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done > BOOTP broadcast 1 > After: > Booting from net ... > BOOTP broadcast 1 > > And you need to check the related code: > drivers/net/dwc_eth_qos.c: phy_startup ->...-> > drivers/net/phy/phy.c: genphy_update_link() > > https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/net/phy/phy.c#L225 > > while (!(mii_reg & BMSR_ANEGCOMPLETE)) { > /* > * Timeout reached ? > */ > if (i > (PHY_ANEG_TIMEOUT / 50)) { > printf(" TIMEOUT !\n"); > phydev->link = 0; > return -ETIMEDOUT; > } > > if (ctrlc()) { > puts("user interrupt!\n"); > phydev->link = 0; > return -EINTR; > } > > if ((i++ % 10) == 0) > printf("."); > > mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR); > mdelay(50); /* 50 ms */ > } > > We can see that one "." is about 500ms, so from the log, we save about 500*7=3500ms=3.5s, this also means that PHY needs about 3.5s to complete auto-nego. > > I also described this in the commit message, "users need wait seconds for PHY auto negotiation to complete when do tftp boot", may not quite clear, I will improve it. > > Best Regards, > Joakim Zhang NACK. Hi Joakim. It's currently working like that for all network drivers, it's not specific What you're currently suggesting is that the link will be brought up automatically for all users, even if they're not interested in network booting. That won't work. Thanks, Ramon
> -----Original Message----- > From: Ramon Fried <rfried.dev@gmail.com> > Sent: 2021年11月16日 18:45 > To: Joakim Zhang <qiangqing.zhang@nxp.com> > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > <patrick.delaunay@foss.st.com>; Daniil Stas <daniil.stas@posteo.net>; > Stephen Warren <swarren@nvidia.com> > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > instead of starting EQOS > > On Tue, Nov 16, 2021 at 10:04 AM Joakim Zhang <qiangqing.zhang@nxp.com> > wrote: > > > > > > Hi Ramon, > > > > > -----Original Message----- > > > From: Ramon Fried <rfried.dev@gmail.com> > > > Sent: 2021年11月16日 13:57 > > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > > > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > > > <patrick.delaunay@foss.st.com>; Daniil Stas > > > <daniil.stas@posteo.net>; Stephen Warren <swarren@nvidia.com> > > > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe > > > stage instead of starting EQOS > > > > > > On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang > > > <qiangqing.zhang@nxp.com> > > > wrote: > > > > > > > > For EQOS ethernet, it will do phy_connect() and phy_config() when > > > > start the ethernet (eqos_srart()), users need wait seconds for PHY > > > > auto negotiation to complete when do tftp boot. > > > > phy_config() > > > > -> board_phy_config() > > > > -> phydev->drv->config() // i.MX8MP/DXL use > > > realtek PHY > > > > -> rtl8211f_config() > > > > -> genphy_config_aneg() > > > > -> > > > genphy_restart_aneg() > > > > // restart auto-nego, then need seconds to complete > > > > > > > > To avoid wasting time, we can move PHY connection and > > > > configuration from > > > > eqos_start() to eqos_probe(). This patch also moves clock setting > > > > from > > > > eqos_start() to eqos_probe() as MDIO access need CSR clock, there > > > > is no function change. > > > > > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > > > > > Before: > > > > u-boot=> run netboot > > > > Booting from net ... > > > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > > > done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 > > > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > > > 10.193.108.176; our IP address is 10.193.102.192; sending through > > > > gateway 10.193.102.254 > > > > After: > > > > u-boot=> run netboot > > > > Booting from net ... > > > > BOOTP broadcast 1 > > > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP > > > > address is 10.193.102.192; sending through gateway 10.193.102.254 > > > > > > > How much time do you save exactly, Is it the ~140ms you show here at > > > the commit log ? > > > > Exactly not. This time points to DHCP client bound to address, not the time > this patch saves. > > > > How can we evaluate the time we save? Please see the log: > > > > Before: > > Booting from net ... > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > done > > BOOTP broadcast 1 > > After: > > Booting from net ... > > BOOTP broadcast 1 > > > > And you need to check the related code: > > drivers/net/dwc_eth_qos.c: phy_startup ->...-> > > drivers/net/phy/phy.c: genphy_update_link() > > > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsour > > > ce.denx.de%2Fu-boot%2Fu-boot%2F-%2Fblob%2Fmaster%2Fdrivers%2Fnet > %2Fphy > > %2Fphy.c%23L225&data=04%7C01%7Cqiangqing.zhang%40nxp.com% > 7C59322db > > > 193a54788a09308d9a8ee2cfc%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0% > 7C0%7 > > > C637726563178464522%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAw > MDAiLCJQIj > > > oiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=usRIR7L > exBnk > > dnDO3U8hHYtMAIWT8bJ0Q7wgTElUjHs%3D&reserved=0 > > > > while (!(mii_reg & BMSR_ANEGCOMPLETE)) { > > /* > > * Timeout reached ? > > */ > > if (i > (PHY_ANEG_TIMEOUT / 50)) { > > printf(" TIMEOUT !\n"); > > phydev->link = 0; > > return -ETIMEDOUT; > > } > > > > if (ctrlc()) { > > puts("user interrupt!\n"); > > phydev->link = 0; > > return -EINTR; > > } > > > > if ((i++ % 10) == 0) > > printf("."); > > > > mii_reg = phy_read(phydev, > MDIO_DEVAD_NONE, MII_BMSR); > > mdelay(50); /* 50 ms */ > > } > > > > We can see that one "." is about 500ms, so from the log, we save about > 500*7=3500ms=3.5s, this also means that PHY needs about 3.5s to complete > auto-nego. > > > > I also described this in the commit message, "users need wait seconds for > PHY auto negotiation to complete when do tftp boot", may not quite clear, I > will improve it. > > > > Best Regards, > > Joakim Zhang > > NACK. > Hi Joakim. > It's currently working like that for all network drivers, it's not specific What > you're currently suggesting is that the link will be brought up automatically > for all users, even if they're not interested in network booting. > That won't work. Hi Ramon, I am not quite understand you mean, I only connect and config the PHY in the MAC probe stage, yes, the link should be brought up, but startup PHY still in MAC open operation, just attaching PHY to MAC in MAC probe, seems not a problem. Is there any side effect? We did the same thing in FEC driver: https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1522 Best Regards, Joakim Zhang > Thanks, > Ramon
On Tue, Nov 16, 2021 at 1:02 PM Joakim Zhang <qiangqing.zhang@nxp.com> wrote: > > > > -----Original Message----- > > From: Ramon Fried <rfried.dev@gmail.com> > > Sent: 2021年11月16日 18:45 > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > > <patrick.delaunay@foss.st.com>; Daniil Stas <daniil.stas@posteo.net>; > > Stephen Warren <swarren@nvidia.com> > > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > > instead of starting EQOS > > > > On Tue, Nov 16, 2021 at 10:04 AM Joakim Zhang <qiangqing.zhang@nxp.com> > > wrote: > > > > > > > > > Hi Ramon, > > > > > > > -----Original Message----- > > > > From: Ramon Fried <rfried.dev@gmail.com> > > > > Sent: 2021年11月16日 13:57 > > > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > > > > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > > > > <patrick.delaunay@foss.st.com>; Daniil Stas > > > > <daniil.stas@posteo.net>; Stephen Warren <swarren@nvidia.com> > > > > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe > > > > stage instead of starting EQOS > > > > > > > > On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang > > > > <qiangqing.zhang@nxp.com> > > > > wrote: > > > > > > > > > > For EQOS ethernet, it will do phy_connect() and phy_config() when > > > > > start the ethernet (eqos_srart()), users need wait seconds for PHY > > > > > auto negotiation to complete when do tftp boot. > > > > > phy_config() > > > > > -> board_phy_config() > > > > > -> phydev->drv->config() // i.MX8MP/DXL use > > > > realtek PHY > > > > > -> rtl8211f_config() > > > > > -> genphy_config_aneg() > > > > > -> > > > > genphy_restart_aneg() > > > > > // restart auto-nego, then need seconds to complete > > > > > > > > > > To avoid wasting time, we can move PHY connection and > > > > > configuration from > > > > > eqos_start() to eqos_probe(). This patch also moves clock setting > > > > > from > > > > > eqos_start() to eqos_probe() as MDIO access need CSR clock, there > > > > > is no function change. > > > > > > > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > > > > > > > Before: > > > > > u-boot=> run netboot > > > > > Booting from net ... > > > > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > > > > done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 > > > > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > > > > 10.193.108.176; our IP address is 10.193.102.192; sending through > > > > > gateway 10.193.102.254 > > > > > After: > > > > > u-boot=> run netboot > > > > > Booting from net ... > > > > > BOOTP broadcast 1 > > > > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > > > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP > > > > > address is 10.193.102.192; sending through gateway 10.193.102.254 > > > > > > > > > How much time do you save exactly, Is it the ~140ms you show here at > > > > the commit log ? > > > > > > Exactly not. This time points to DHCP client bound to address, not the time > > this patch saves. > > > > > > How can we evaluate the time we save? Please see the log: > > > > > > Before: > > > Booting from net ... > > > ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... > > done > > > BOOTP broadcast 1 > > > After: > > > Booting from net ... > > > BOOTP broadcast 1 > > > > > > And you need to check the related code: > > > drivers/net/dwc_eth_qos.c: phy_startup ->...-> > > > drivers/net/phy/phy.c: genphy_update_link() > > > > > > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsour > > > > > ce.denx.de%2Fu-boot%2Fu-boot%2F-%2Fblob%2Fmaster%2Fdrivers%2Fnet > > %2Fphy > > > %2Fphy.c%23L225&data=04%7C01%7Cqiangqing.zhang%40nxp.com% > > 7C59322db > > > > > 193a54788a09308d9a8ee2cfc%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0% > > 7C0%7 > > > > > C637726563178464522%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAw > > MDAiLCJQIj > > > > > oiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=usRIR7L > > exBnk > > > dnDO3U8hHYtMAIWT8bJ0Q7wgTElUjHs%3D&reserved=0 > > > > > > while (!(mii_reg & BMSR_ANEGCOMPLETE)) { > > > /* > > > * Timeout reached ? > > > */ > > > if (i > (PHY_ANEG_TIMEOUT / 50)) { > > > printf(" TIMEOUT !\n"); > > > phydev->link = 0; > > > return -ETIMEDOUT; > > > } > > > > > > if (ctrlc()) { > > > puts("user interrupt!\n"); > > > phydev->link = 0; > > > return -EINTR; > > > } > > > > > > if ((i++ % 10) == 0) > > > printf("."); > > > > > > mii_reg = phy_read(phydev, > > MDIO_DEVAD_NONE, MII_BMSR); > > > mdelay(50); /* 50 ms */ > > > } > > > > > > We can see that one "." is about 500ms, so from the log, we save about > > 500*7=3500ms=3.5s, this also means that PHY needs about 3.5s to complete > > auto-nego. > > > > > > I also described this in the commit message, "users need wait seconds for > > PHY auto negotiation to complete when do tftp boot", may not quite clear, I > > will improve it. > > > > > > Best Regards, > > > Joakim Zhang > > > > NACK. > > Hi Joakim. > > It's currently working like that for all network drivers, it's not specific What > > you're currently suggesting is that the link will be brought up automatically > > for all users, even if they're not interested in network booting. > > That won't work. > > Hi Ramon, > > I am not quite understand you mean, I only connect and config the PHY in the MAC probe stage, yes, the link should be brought up, > but startup PHY still in MAC open operation, just attaching PHY to MAC in MAC probe, seems not a problem. Is there any side effect? The link up is a side effect, the U-Boot device model works in lazy loading mode, where stuff is initialized only when needed. This works the same for all phys in all places. Additionally, I'm not following how much time can you actually save, how much time passes between the probe() function and start() function in your setup ? how could it be seconds ? > > We did the same thing in FEC driver: https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/net/fec_mxc.c#L1522 True, that's an example that contradicts what I just said, but it's wrong. > > Best Regards, > Joakim Zhang > > Thanks, > > Ramon
Hi Ramon, > -----Original Message----- > From: Ramon Fried <rfried.dev@gmail.com> > Sent: 2021年11月17日 12:20 > To: Joakim Zhang <qiangqing.zhang@nxp.com> > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > <patrick.delaunay@foss.st.com>; Daniil Stas <daniil.stas@posteo.net>; > Stephen Warren <swarren@nvidia.com> > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe stage > instead of starting EQOS > > On Tue, Nov 16, 2021 at 1:02 PM Joakim Zhang <qiangqing.zhang@nxp.com> > wrote: > > > > > > > -----Original Message----- > > > From: Ramon Fried <rfried.dev@gmail.com> > > > Sent: 2021年11月16日 18:45 > > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing List > > > <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick Delaunay > > > <patrick.delaunay@foss.st.com>; Daniil Stas > > > <daniil.stas@posteo.net>; Stephen Warren <swarren@nvidia.com> > > > Subject: Re: [PATCH] net: eqos: connect and config PHY from probe > > > stage instead of starting EQOS > > > > > > On Tue, Nov 16, 2021 at 10:04 AM Joakim Zhang > > > <qiangqing.zhang@nxp.com> > > > wrote: > > > > > > > > > > > > Hi Ramon, > > > > > > > > > -----Original Message----- > > > > > From: Ramon Fried <rfried.dev@gmail.com> > > > > > Sent: 2021年11月16日 13:57 > > > > > To: Joakim Zhang <qiangqing.zhang@nxp.com> > > > > > Cc: Joe Hershberger <joe.hershberger@ni.com>; U-Boot Mailing > > > > > List <u-boot@lists.denx.de>; Ye Li <ye.li@nxp.com>; Patrick > > > > > Delaunay <patrick.delaunay@foss.st.com>; Daniil Stas > > > > > <daniil.stas@posteo.net>; Stephen Warren <swarren@nvidia.com> > > > > > Subject: Re: [PATCH] net: eqos: connect and config PHY from > > > > > probe stage instead of starting EQOS > > > > > > > > > > On Wed, Nov 10, 2021 at 7:42 AM Joakim Zhang > > > > > <qiangqing.zhang@nxp.com> > > > > > wrote: > > > > > > > > > > > > For EQOS ethernet, it will do phy_connect() and phy_config() > > > > > > when start the ethernet (eqos_srart()), users need wait > > > > > > seconds for PHY auto negotiation to complete when do tftp boot. > > > > > > phy_config() > > > > > > -> board_phy_config() > > > > > > -> phydev->drv->config() // i.MX8MP/DXL > > > > > > use > > > > > realtek PHY > > > > > > -> rtl8211f_config() > > > > > > -> genphy_config_aneg() > > > > > > -> > > > > > genphy_restart_aneg() > > > > > > // restart auto-nego, then need seconds to complete > > > > > > > > > > > > To avoid wasting time, we can move PHY connection and > > > > > > configuration from > > > > > > eqos_start() to eqos_probe(). This patch also moves clock > > > > > > setting from > > > > > > eqos_start() to eqos_probe() as MDIO access need CSR clock, > > > > > > there is no function change. > > > > > > > > > > > > Tested-on: i.MX8MP & i.MX8DXL > > > > > > > > > > > > Before: > > > > > > u-boot=> run netboot > > > > > > Booting from net ... > > > > > > ethernet@30bf0000 Waiting for PHY auto negotiation to > complete....... > > > > > > done BOOTP broadcast 1 DHCP client bound to address > > > > > > 10.193.102.192 > > > > > > (313 ms) Using ethernet@30bf0000 device TFTP from server > > > > > > 10.193.108.176; our IP address is 10.193.102.192; sending > > > > > > through gateway 10.193.102.254 > > > > > > After: > > > > > > u-boot=> run netboot > > > > > > Booting from net ... > > > > > > BOOTP broadcast 1 > > > > > > DHCP client bound to address 10.193.102.192 (454 ms) Using > > > > > > ethernet@30bf0000 device TFTP from server 10.193.108.176; our > > > > > > IP address is 10.193.102.192; sending through gateway > > > > > > 10.193.102.254 > > > > > > > > > > > How much time do you save exactly, Is it the ~140ms you show > > > > > here at the commit log ? > > > > > > > > Exactly not. This time points to DHCP client bound to address, not > > > > the time > > > this patch saves. > > > > > > > > How can we evaluate the time we save? Please see the log: > > > > > > > > Before: > > > > Booting from net ... > > > > ethernet@30bf0000 Waiting for PHY auto negotiation to > complete....... > > > done > > > > BOOTP broadcast 1 > > > > After: > > > > Booting from net ... > > > > BOOTP broadcast 1 > > > > > > > > And you need to check the related code: > > > > drivers/net/dwc_eth_qos.c: phy_startup ->...-> > > > > drivers/net/phy/phy.c: genphy_update_link() > > > > > > > > > > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fso > > > ur > > > > > > > > ce.denx.de%2Fu-boot%2Fu-boot%2F-%2Fblob%2Fmaster%2Fdrivers%2Fnet > > > %2Fphy > > > > %2Fphy.c%23L225&data=04%7C01%7Cqiangqing.zhang%40nxp.co > m% > > > 7C59322db > > > > > > > > 193a54788a09308d9a8ee2cfc%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0% > > > 7C0%7 > > > > > > > > C637726563178464522%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAw > > > MDAiLCJQIj > > > > > > > > oiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=usRIR7L > > > exBnk > > > > dnDO3U8hHYtMAIWT8bJ0Q7wgTElUjHs%3D&reserved=0 > > > > > > > > while (!(mii_reg & BMSR_ANEGCOMPLETE)) { > > > > /* > > > > * Timeout reached ? > > > > */ > > > > if (i > (PHY_ANEG_TIMEOUT / 50)) { > > > > printf(" TIMEOUT !\n"); > > > > phydev->link = 0; > > > > return -ETIMEDOUT; > > > > } > > > > > > > > if (ctrlc()) { > > > > puts("user interrupt!\n"); > > > > phydev->link = 0; > > > > return -EINTR; > > > > } > > > > > > > > if ((i++ % 10) == 0) > > > > printf("."); > > > > > > > > mii_reg = phy_read(phydev, > > > MDIO_DEVAD_NONE, MII_BMSR); > > > > mdelay(50); /* 50 ms */ > > > > } > > > > > > > > We can see that one "." is about 500ms, so from the log, we save > > > > about > > > 500*7=3500ms=3.5s, this also means that PHY needs about 3.5s to > > > complete auto-nego. > > > > > > > > I also described this in the commit message, "users need wait > > > > seconds for > > > PHY auto negotiation to complete when do tftp boot", may not quite > > > clear, I will improve it. > > > > > > > > Best Regards, > > > > Joakim Zhang > > > > > > NACK. > > > Hi Joakim. > > > It's currently working like that for all network drivers, it's not > > > specific What you're currently suggesting is that the link will be > > > brought up automatically for all users, even if they're not interested in > network booting. > > > That won't work. > > > > Hi Ramon, > > > > I am not quite understand you mean, I only connect and config the PHY > > in the MAC probe stage, yes, the link should be brought up, but startup > PHY still in MAC open operation, just attaching PHY to MAC in MAC probe, > seems not a problem. Is there any side effect? > The link up is a side effect, the U-Boot device model works in lazy loading > mode, where stuff is initialized only when needed. This works the same for > all phys in all places. Understand, thanks. > Additionally, I'm not following how much time can you actually save, how > much time passes between the probe() function and start() function in your > setup ? how could it be seconds ? Actually, Realtek PHY(RTL8211FDI) at my side, it needs about 3.5s to complete auto-negotiation. If we connect and config PHY in probe(), it _may_ complete auto-nego when user start network (start()), as you said, yes, if we start network quickly, we also need some time to wait it to complete. However, at least, we can save some time compared to connect and config PHY in start(), where we need wait about 3.5s to complete auto-nego. > > > > We did the same thing in FEC driver: > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fsour > > > ce.denx.de%2Fu-boot%2Fu-boot%2F-%2Fblob%2Fmaster%2Fdrivers%2Fnet > %2Ffec > > > _mxc.c%23L1522&data=04%7C01%7Cqiangqing.zhang%40nxp.com%7C4 > 3be042d > > > 7b6f427f406708d9a98188f8%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7 > C0%7C > > > 637727196088131120%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwM > DAiLCJQIjo > > > iV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=bElnoO13 > uq0kg > > t7yzIFwiMJpVH3L49SNF5dssplt%2Fjw%3D&reserved=0 > True, that's an example that contradicts what I just said, but it's wrong. OK. Best Regards, Joakim Zhang > > Best Regards, > > Joakim Zhang > > > Thanks, > > > Ramon
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c index 585101804d..c1923fbe6b 100644 --- a/drivers/net/dwc_eth_qos.c +++ b/drivers/net/dwc_eth_qos.c @@ -1045,20 +1045,6 @@ static int eqos_start(struct udevice *dev) eqos->tx_desc_idx = 0; eqos->rx_desc_idx = 0; - ret = eqos->config->ops->eqos_start_clks(dev); - if (ret < 0) { - pr_err("eqos_start_clks() failed: %d", ret); - goto err; - } - - ret = eqos->config->ops->eqos_start_resets(dev); - if (ret < 0) { - pr_err("eqos_start_resets() failed: %d", ret); - goto err_stop_clks; - } - - udelay(10); - eqos->reg_access_ok = true; ret = wait_for_bit_le32(&eqos->dma_regs->mode, @@ -1066,68 +1052,34 @@ static int eqos_start(struct udevice *dev) eqos->config->swr_wait, false); if (ret) { pr_err("EQOS_DMA_MODE_SWR stuck"); - goto err_stop_resets; + goto err; } ret = eqos->config->ops->eqos_calibrate_pads(dev); if (ret < 0) { pr_err("eqos_calibrate_pads() failed: %d", ret); - goto err_stop_resets; + goto err; } rate = eqos->config->ops->eqos_get_tick_clk_rate(dev); val = (rate / 1000000) - 1; writel(val, &eqos->mac_regs->us_tic_counter); - /* - * if PHY was already connected and configured, - * don't need to reconnect/reconfigure again - */ - if (!eqos->phy) { - int addr = -1; -#ifdef CONFIG_DM_ETH_PHY - addr = eth_phy_get_addr(dev); -#endif -#ifdef DWC_NET_PHYADDR - addr = DWC_NET_PHYADDR; -#endif - eqos->phy = phy_connect(eqos->mii, addr, dev, - eqos->config->interface(dev)); - if (!eqos->phy) { - pr_err("phy_connect() failed"); - goto err_stop_resets; - } - - if (eqos->max_speed) { - ret = phy_set_supported(eqos->phy, eqos->max_speed); - if (ret) { - pr_err("phy_set_supported() failed: %d", ret); - goto err_shutdown_phy; - } - } - - ret = phy_config(eqos->phy); - if (ret < 0) { - pr_err("phy_config() failed: %d", ret); - goto err_shutdown_phy; - } - } - ret = phy_startup(eqos->phy); if (ret < 0) { pr_err("phy_startup() failed: %d", ret); - goto err_shutdown_phy; + goto err; } if (!eqos->phy->link) { pr_err("No link"); - goto err_shutdown_phy; + goto err; } ret = eqos_adjust_link(dev); if (ret < 0) { pr_err("eqos_adjust_link() failed: %d", ret); - goto err_shutdown_phy; + goto err; } /* Configure MTL */ @@ -1356,12 +1308,6 @@ static int eqos_start(struct udevice *dev) debug("%s: OK\n", __func__); return 0; -err_shutdown_phy: - phy_shutdown(eqos->phy); -err_stop_resets: - eqos->config->ops->eqos_stop_resets(dev); -err_stop_clks: - eqos->config->ops->eqos_stop_clks(dev); err: pr_err("FAILED: %d", ret); return ret; @@ -1412,12 +1358,6 @@ static void eqos_stop(struct udevice *dev) clrbits_le32(&eqos->dma_regs->ch0_rx_control, EQOS_DMA_CH0_RX_CONTROL_SR); - if (eqos->phy) { - phy_shutdown(eqos->phy); - } - eqos->config->ops->eqos_stop_resets(dev); - eqos->config->ops->eqos_stop_clks(dev); - debug("%s: OK\n", __func__); } @@ -1888,9 +1828,65 @@ static int eqos_probe(struct udevice *dev) eth_phy_set_mdio_bus(dev, eqos->mii); #endif + ret = eqos->config->ops->eqos_start_clks(dev); + if (ret < 0) { + pr_err("eqos_start_clks() failed: %d", ret); + goto err_unregister_mdio; + } + + ret = eqos->config->ops->eqos_start_resets(dev); + if (ret < 0) { + pr_err("eqos_start_resets() failed: %d", ret); + goto err_stop_clks; + } + + udelay(10); + + /* + * if PHY was already connected and configured, + * don't need to reconnect/reconfigure again + */ + if (!eqos->phy) { + int addr = -1; +#ifdef CONFIG_DM_ETH_PHY + addr = eth_phy_get_addr(dev); +#endif +#ifdef DWC_NET_PHYADDR + addr = DWC_NET_PHYADDR; +#endif + eqos->phy = phy_connect(eqos->mii, addr, dev, + eqos->config->interface(dev)); + if (!eqos->phy) { + pr_err("phy_connect() failed"); + goto err_stop_resets; + } + + if (eqos->max_speed) { + ret = phy_set_supported(eqos->phy, eqos->max_speed); + if (ret) { + pr_err("phy_set_supported() failed: %d", ret); + goto err_shutdown_phy; + } + } + + ret = phy_config(eqos->phy); + if (ret < 0) { + pr_err("phy_config() failed: %d", ret); + goto err_shutdown_phy; + } + } + debug("%s: OK\n", __func__); return 0; +err_shutdown_phy: + phy_shutdown(eqos->phy); +err_stop_resets: + eqos->config->ops->eqos_stop_resets(dev); +err_stop_clks: + eqos->config->ops->eqos_stop_clks(dev); +err_unregister_mdio: + mdio_unregister(eqos->mii); err_free_mdio: mdio_free(eqos->mii); err_remove_resources_tegra: @@ -1908,6 +1904,12 @@ static int eqos_remove(struct udevice *dev) debug("%s(dev=%p):\n", __func__, dev); + if (eqos->phy) { + phy_shutdown(eqos->phy); + } + eqos->config->ops->eqos_stop_resets(dev); + eqos->config->ops->eqos_stop_clks(dev); + mdio_unregister(eqos->mii); mdio_free(eqos->mii); eqos->config->ops->eqos_remove_resources(dev);
For EQOS ethernet, it will do phy_connect() and phy_config() when start the ethernet (eqos_srart()), users need wait seconds for PHY auto negotiation to complete when do tftp boot. phy_config() -> board_phy_config() -> phydev->drv->config() // i.MX8MP/DXL use realtek PHY -> rtl8211f_config() -> genphy_config_aneg() -> genphy_restart_aneg() // restart auto-nego, then need seconds to complete To avoid wasting time, we can move PHY connection and configuration from eqos_start() to eqos_probe(). This patch also moves clock setting from eqos_start() to eqos_probe() as MDIO access need CSR clock, there is no function change. Tested-on: i.MX8MP & i.MX8DXL Before: u-boot=> run netboot Booting from net ... ethernet@30bf0000 Waiting for PHY auto negotiation to complete....... done BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 (313 ms) Using ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 After: u-boot=> run netboot Booting from net ... BOOTP broadcast 1 DHCP client bound to address 10.193.102.192 (454 ms) Using ethernet@30bf0000 device TFTP from server 10.193.108.176; our IP address is 10.193.102.192; sending through gateway 10.193.102.254 Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> --- drivers/net/dwc_eth_qos.c | 132 +++++++++++++++++++------------------- 1 file changed, 67 insertions(+), 65 deletions(-)