| Message ID | 20210103100013.47058-2-jernej.skrabec@siol.net |
|---|---|
| State | Superseded |
| Delegated to: | Andre Przywara |
| Headers | show |
| Series | sunxi: add support for Tanix TX6 | expand |
On 03/01/2021 10:00, Jernej Skrabec wrote: > Updated H6 DT files are based on Linux 5.11-rc1 release. > > Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> That looks alright, but it seems like the OrangePi One Plus .dts is not updated? Cheers, Andre > --- > arch/arm/dts/sun50i-h6-beelink-gs1.dts | 70 +++- > arch/arm/dts/sun50i-h6-cpu-opp.dtsi | 117 +++++++ > arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 71 +++- > arch/arm/dts/sun50i-h6-orangepi.dtsi | 72 +++- > arch/arm/dts/sun50i-h6-pine-h64.dts | 102 ++++-- > arch/arm/dts/sun50i-h6.dtsi | 394 ++++++++++++++++++++-- > 6 files changed, 758 insertions(+), 68 deletions(-) > create mode 100644 arch/arm/dts/sun50i-h6-cpu-opp.dtsi > > diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts > index 0dc33c90dd60..7c9dbde645b5 100644 > --- a/arch/arm/dts/sun50i-h6-beelink-gs1.dts > +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts > @@ -1,11 +1,10 @@ > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > -/* > - * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> > - */ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> > > /dts-v1/; > > #include "sun50i-h6.dtsi" > +#include "sun50i-h6-cpu-opp.dtsi" > > #include <dt-bindings/gpio/gpio.h> > > @@ -25,6 +24,7 @@ > connector { > compatible = "hdmi-connector"; > type = "a"; > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > > port { > hdmi_con_in: endpoint { > @@ -33,6 +33,13 @@ > }; > }; > > + ext_osc32k: ext_osc32k_clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <32768>; > + clock-output-names = "ext_osc32k"; > + }; > + > leds { > compatible = "gpio-leds"; > > @@ -51,12 +58,38 @@ > regulator-max-microvolt = <5000000>; > regulator-always-on; > }; > + > + sound-spdif { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "sun50i-h6-spdif"; > + > + simple-audio-card,cpu { > + sound-dai = <&spdif>; > + }; > + > + simple-audio-card,codec { > + sound-dai = <&spdif_out>; > + }; > + }; > + > + spdif_out: spdif-out { > + #sound-dai-cells = <0>; > + compatible = "linux,spdif-dit"; > + }; > +}; > + > +&cpu0 { > + cpu-supply = <®_dcdca>; > }; > > &de { > status = "okay"; > }; > > +&dwc3 { > + status = "okay"; > +}; > + > &ehci0 { > status = "okay"; > }; > @@ -64,12 +97,17 @@ > &emac { > pinctrl-names = "default"; > pinctrl-0 = <&ext_rgmii_pins>; > - phy-mode = "rgmii"; > + phy-mode = "rgmii-id"; > phy-handle = <&ext_rgmii_phy>; > phy-supply = <®_aldo2>; > status = "okay"; > }; > > +&gpu { > + mali-supply = <®_dcdcc>; > + status = "okay"; > +}; > + > &hdmi { > status = "okay"; > }; > @@ -201,13 +239,16 @@ > reg_dcdca: dcdca { > regulator-always-on; > regulator-min-microvolt = <810000>; > - regulator-max-microvolt = <1080000>; > + regulator-max-microvolt = <1160000>; > + regulator-ramp-delay = <2500>; > regulator-name = "vdd-cpu"; > }; > > reg_dcdcc: dcdcc { > + regulator-enable-ramp-delay = <32000>; > regulator-min-microvolt = <810000>; > regulator-max-microvolt = <1080000>; > + regulator-ramp-delay = <2500>; > regulator-name = "vdd-gpu"; > }; > > @@ -232,6 +273,11 @@ > }; > }; > > +&r_ir { > + linux,rc-map-name = "rc-beelink-gs1"; > + status = "okay"; > +}; > + > &r_pio { > /* > * PL0 and PL1 are used for PMIC I2C > @@ -243,6 +289,14 @@ > vcc-pm-supply = <®_aldo1>; > }; > > +&rtc { > + clocks = <&ext_osc32k>; > +}; > + > +&spdif { > + status = "okay"; > +}; > + > &uart0 { > pinctrl-names = "default"; > pinctrl-0 = <&uart0_ph_pins>; > @@ -258,3 +312,7 @@ > usb0_vbus-supply = <®_vcc5v>; > status = "okay"; > }; > + > +&usb3phy { > + status = "okay"; > +}; > diff --git a/arch/arm/dts/sun50i-h6-cpu-opp.dtsi b/arch/arm/dts/sun50i-h6-cpu-opp.dtsi > new file mode 100644 > index 000000000000..1a5eddc5a40f > --- /dev/null > +++ b/arch/arm/dts/sun50i-h6-cpu-opp.dtsi > @@ -0,0 +1,117 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > +// Copyright (C) 2020 Clément Péron <peron.clem@gmail.com> > + > +/ { > + cpu_opp_table: cpu-opp-table { > + compatible = "allwinner,sun50i-h6-operating-points"; > + nvmem-cells = <&cpu_speed_grade>; > + opp-shared; > + > + opp@480000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <480000000>; > + > + opp-microvolt-speed0 = <880000 880000 1200000>; > + opp-microvolt-speed1 = <820000 820000 1200000>; > + opp-microvolt-speed2 = <820000 820000 1200000>; > + }; > + > + opp@720000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <720000000>; > + > + opp-microvolt-speed0 = <880000 880000 1200000>; > + opp-microvolt-speed1 = <820000 820000 1200000>; > + opp-microvolt-speed2 = <820000 820000 1200000>; > + }; > + > + opp@816000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <816000000>; > + > + opp-microvolt-speed0 = <880000 880000 1200000>; > + opp-microvolt-speed1 = <820000 820000 1200000>; > + opp-microvolt-speed2 = <820000 820000 1200000>; > + }; > + > + opp@888000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <888000000>; > + > + opp-microvolt-speed0 = <880000 880000 1200000>; > + opp-microvolt-speed1 = <820000 820000 1200000>; > + opp-microvolt-speed2 = <820000 820000 1200000>; > + }; > + > + opp@1080000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1080000000>; > + > + opp-microvolt-speed0 = <940000 940000 1200000>; > + opp-microvolt-speed1 = <880000 880000 1200000>; > + opp-microvolt-speed2 = <880000 880000 1200000>; > + }; > + > + opp@1320000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1320000000>; > + > + opp-microvolt-speed0 = <1000000 1000000 1200000>; > + opp-microvolt-speed1 = <940000 940000 1200000>; > + opp-microvolt-speed2 = <940000 940000 1200000>; > + }; > + > + opp@1488000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1488000000>; > + > + opp-microvolt-speed0 = <1060000 1060000 1200000>; > + opp-microvolt-speed1 = <1000000 1000000 1200000>; > + opp-microvolt-speed2 = <1000000 1000000 1200000>; > + }; > + > + opp@1608000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1608000000>; > + > + opp-microvolt-speed0 = <1090000 1090000 1200000>; > + opp-microvolt-speed1 = <1030000 1030000 1200000>; > + opp-microvolt-speed2 = <1030000 1030000 1200000>; > + }; > + > + opp@1704000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1704000000>; > + > + opp-microvolt-speed0 = <1120000 1120000 1200000>; > + opp-microvolt-speed1 = <1060000 1060000 1200000>; > + opp-microvolt-speed2 = <1060000 1060000 1200000>; > + }; > + > + opp@1800000000 { > + clock-latency-ns = <244144>; /* 8 32k periods */ > + opp-hz = /bits/ 64 <1800000000>; > + > + opp-microvolt-speed0 = <1160000 1160000 1200000>; > + opp-microvolt-speed1 = <1100000 1100000 1200000>; > + opp-microvolt-speed2 = <1100000 1100000 1200000>; > + }; > + }; > +}; > + > +&cpu0 { > + operating-points-v2 = <&cpu_opp_table>; > +}; > + > +&cpu1 { > + operating-points-v2 = <&cpu_opp_table>; > +}; > + > +&cpu2 { > + operating-points-v2 = <&cpu_opp_table>; > +}; > + > +&cpu3 { > + operating-points-v2 = <&cpu_opp_table>; > +}; > diff --git a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts > index e098a2475f2d..e8770858b5d0 100644 > --- a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts > +++ b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts > @@ -1,11 +1,74 @@ > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > -/* > - * Copyright (C) 2018 Jagan Teki <jagan@openedev.com> > - */ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2018 Jagan Teki <jagan@openedev.com> > > #include "sun50i-h6-orangepi.dtsi" > > / { > model = "OrangePi Lite2"; > compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6"; > + > + aliases { > + serial1 = &uart1; /* BT-UART */ > + }; > + > + wifi_pwrseq: wifi_pwrseq { > + compatible = "mmc-pwrseq-simple"; > + clocks = <&rtc 1>; > + clock-names = "ext_clock"; > + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ > + post-power-on-delay-ms = <200>; > + }; > +}; > + > +&mmc1 { > + vmmc-supply = <®_cldo2>; > + vqmmc-supply = <®_bldo3>; > + mmc-pwrseq = <&wifi_pwrseq>; > + bus-width = <4>; > + non-removable; > + status = "okay"; > + > + brcm: sdio-wifi@1 { > + reg = <1>; > + compatible = "brcm,bcm4329-fmac"; > + interrupt-parent = <&r_pio>; > + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ > + interrupt-names = "host-wake"; > + }; > +}; > + > +®_cldo2 { > + /* > + * This regulator is connected with CLDO3. > + * Before the kernel can support synchronized > + * enable of coupled regulators, keep them > + * both always on as a ugly hack. > + */ > + regulator-always-on; > +}; > + > +®_cldo3 { > + /* > + * This regulator is connected with CLDO2. > + * See the comments for CLDO2. > + */ > + regulator-always-on; > +}; > + > +/* There's the BT part of the AP6255 connected to that UART */ > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; > + uart-has-rtscts; > + status = "okay"; > + > + bluetooth { > + compatible = "brcm,bcm4345c5"; > + clocks = <&rtc 1>; > + clock-names = "lpo"; > + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ > + host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ > + shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ > + max-speed = <1500000>; > + }; > }; > diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6-orangepi.dtsi > index 62e27948a3fa..ebc120a9232f 100644 > --- a/arch/arm/dts/sun50i-h6-orangepi.dtsi > +++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi > @@ -1,8 +1,6 @@ > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > -/* > - * Copyright (C) 2018 Amarula Solutions > - * Author: Jagan Teki <jagan@amarulasolutions.com> > - */ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2018 Amarula Solutions > +// Author: Jagan Teki <jagan@amarulasolutions.com> > > /dts-v1/; > > @@ -22,6 +20,25 @@ > stdout-path = "serial0:115200n8"; > }; > > + connector { > + compatible = "hdmi-connector"; > + type = "a"; > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > + > + port { > + hdmi_con_in: endpoint { > + remote-endpoint = <&hdmi_out_con>; > + }; > + }; > + }; > + > + ext_osc32k: ext_osc32k_clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <32768>; > + clock-output-names = "ext_osc32k"; > + }; > + > leds { > compatible = "gpio-leds"; > > @@ -47,6 +64,10 @@ > }; > }; > > +&de { > + status = "okay"; > +}; > + > &ehci0 { > status = "okay"; > }; > @@ -55,6 +76,21 @@ > status = "okay"; > }; > > +&gpu { > + mali-supply = <®_dcdcc>; > + status = "okay"; > +}; > + > +&hdmi { > + status = "okay"; > +}; > + > +&hdmi_out { > + hdmi_out_con: endpoint { > + remote-endpoint = <&hdmi_con_in>; > + }; > +}; > + > &mmc0 { > vmmc-supply = <®_cldo1>; > cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; > @@ -70,6 +106,12 @@ > status = "okay"; > }; > > +&pio { > + vcc-pc-supply = <®_bldo2>; > + vcc-pd-supply = <®_cldo1>; > + vcc-pg-supply = <®_aldo1>; > +}; > + > &r_i2c { > status = "okay"; > > @@ -163,6 +205,7 @@ > }; > > reg_dcdcc: dcdcc { > + regulator-enable-ramp-delay = <32000>; > regulator-min-microvolt = <810000>; > regulator-max-microvolt = <1080000>; > regulator-name = "vdd-gpu"; > @@ -189,6 +232,18 @@ > }; > }; > > +&r_ir { > + status = "okay"; > +}; > + > +&r_pio { > + vcc-pm-supply = <®_bldo3>; > +}; > + > +&rtc { > + clocks = <&ext_osc32k>; > +}; > + > &uart0 { > pinctrl-names = "default"; > pinctrl-0 = <&uart0_ph_pins>; > @@ -196,7 +251,12 @@ > }; > > &usb2otg { > - dr_mode = "otg"; > + /* > + * OrangePi Lite 2 and One Plus, where this DT is used, don't > + * have a controllable VBUS even though they do have an ID pin. > + * Using it as anything but a USB host is unsafe. > + */ > + dr_mode = "host"; > status = "okay"; > }; > > diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts b/arch/arm/dts/sun50i-h6-pine-h64.dts > index 189834518391..961732c52aa0 100644 > --- a/arch/arm/dts/sun50i-h6-pine-h64.dts > +++ b/arch/arm/dts/sun50i-h6-pine-h64.dts > @@ -1,30 +1,38 @@ > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > -/* > - * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> > - */ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> > > /dts-v1/; > > #include "sun50i-h6.dtsi" > +#include "sun50i-h6-cpu-opp.dtsi" > > #include <dt-bindings/gpio/gpio.h> > > / { > - model = "Pine H64"; > + model = "Pine H64 model A"; > compatible = "pine64,pine-h64", "allwinner,sun50i-h6"; > > aliases { > ethernet0 = &emac; > serial0 = &uart0; > + spi0 = &spi0; > }; > > chosen { > stdout-path = "serial0:115200n8"; > }; > > - connector { > + ext_osc32k: ext_osc32k_clk { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <32768>; > + clock-output-names = "ext_osc32k"; > + }; > + > + hdmi_connector: connector { > compatible = "hdmi-connector"; > type = "a"; > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > > port { > hdmi_con_in: endpoint { > @@ -52,6 +60,16 @@ > }; > }; > > + reg_gmac_3v3: gmac-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc-gmac-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <100000>; > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > reg_usb_vbus: vbus { > compatible = "regulator-fixed"; > regulator-name = "usb-vbus"; > @@ -63,25 +81,35 @@ > }; > }; > > +&cpu0 { > + cpu-supply = <®_dcdca>; > +}; > + > +&de { > + status = "okay"; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci3 { > + status = "okay"; > +}; > + > &emac { > pinctrl-names = "default"; > pinctrl-0 = <&ext_rgmii_pins>; > - phy-mode = "rgmii"; > + phy-mode = "rgmii-id"; > phy-handle = <&ext_rgmii_phy>; > - phy-supply = <®_aldo2>; > + phy-supply = <®_gmac_3v3>; > allwinner,rx-delay-ps = <200>; > allwinner,tx-delay-ps = <200>; > status = "okay"; > }; > > -&mdio { > - ext_rgmii_phy: ethernet-phy@1 { > - compatible = "ethernet-phy-ieee802.3-c22"; > - reg = <1>; > - }; > -}; > - > -&de { > +&gpu { > + mali-supply = <®_dcdcc>; > status = "okay"; > }; > > @@ -95,12 +123,11 @@ > }; > }; > > -&ehci0 { > - status = "okay"; > -}; > - > -&ehci3 { > - status = "okay"; > +&mdio { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > }; > > &mmc0 { > @@ -216,13 +243,16 @@ > reg_dcdca: dcdca { > regulator-always-on; > regulator-min-microvolt = <810000>; > - regulator-max-microvolt = <1080000>; > + regulator-max-microvolt = <1160000>; > + regulator-ramp-delay = <2500>; > regulator-name = "vdd-cpu"; > }; > > reg_dcdcc: dcdcc { > + regulator-enable-ramp-delay = <32000>; > regulator-min-microvolt = <810000>; > regulator-max-microvolt = <1080000>; > + regulator-ramp-delay = <2500>; > regulator-name = "vdd-gpu"; > }; > > @@ -255,10 +285,36 @@ > }; > }; > > +&r_ir { > + status = "okay"; > +}; > + > &r_pio { > vcc-pm-supply = <®_aldo1>; > }; > > +&rtc { > + clocks = <&ext_osc32k>; > +}; > + > +/* > + * The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI > + * flash and eMMC at the same time, as one of them would fail probing. > + * Disable SPI0 in here, to prefer the more useful eMMC. U-Boot can > + * fix this up in no eMMC is connected. > + */ > +&spi0 { > + pinctrl-0 = <&spi0_pins>, <&spi0_cs_pin>; > + pinctrl-names = "default"; > + status = "disabled"; > + > + flash@0 { > + compatible = "winbond,w25q128", "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <4000000>; > + }; > +}; > + > &uart0 { > pinctrl-names = "default"; > pinctrl-0 = <&uart0_ph_pins>; > diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi > index a117f479ae55..8a62a9fbe347 100644 > --- a/arch/arm/dts/sun50i-h6.dtsi > +++ b/arch/arm/dts/sun50i-h6.dtsi > @@ -1,7 +1,5 @@ > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > -/* > - * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > - */ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/sun50i-h6-ccu.h> > @@ -11,6 +9,7 @@ > #include <dt-bindings/reset/sun50i-h6-ccu.h> > #include <dt-bindings/reset/sun50i-h6-r-ccu.h> > #include <dt-bindings/reset/sun8i-de2.h> > +#include <dt-bindings/thermal/thermal.h> > > / { > interrupt-parent = <&gic>; > @@ -26,6 +25,9 @@ > device_type = "cpu"; > reg = <0>; > enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + clock-latency-ns = <244144>; /* 8 32k periods */ > + #cooling-cells = <2>; > }; > > cpu1: cpu@1 { > @@ -33,6 +35,9 @@ > device_type = "cpu"; > reg = <1>; > enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + clock-latency-ns = <244144>; /* 8 32k periods */ > + #cooling-cells = <2>; > }; > > cpu2: cpu@2 { > @@ -40,6 +45,9 @@ > device_type = "cpu"; > reg = <2>; > enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + clock-latency-ns = <244144>; /* 8 32k periods */ > + #cooling-cells = <2>; > }; > > cpu3: cpu@3 { > @@ -47,6 +55,9 @@ > device_type = "cpu"; > reg = <3>; > enable-method = "psci"; > + clocks = <&ccu CLK_CPUX>; > + clock-latency-ns = <244144>; /* 8 32k periods */ > + #cooling-cells = <2>; > }; > }; > > @@ -56,14 +67,6 @@ > status = "disabled"; > }; > > - iosc: internal-osc-clk { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <16000000>; > - clock-accuracy = <300000000>; > - clock-output-names = "iosc"; > - }; > - > osc24M: osc24M_clk { > #clock-cells = <0>; > compatible = "fixed-clock"; > @@ -71,11 +74,13 @@ > clock-output-names = "osc24M"; > }; > > - osc32k: osc32k_clk { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <32768>; > - clock-output-names = "osc32k"; > + pmu { > + compatible = "arm,cortex-a53-pmu"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > }; > > psci { > @@ -85,6 +90,7 @@ > > timer { > compatible = "arm,armv8-timer"; > + arm,no-tick-in-suspend; > interrupts = <GIC_PPI 13 > (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > <GIC_PPI 14 > @@ -130,6 +136,7 @@ > clock-names = "bus", > "mod"; > resets = <&display_clocks RST_MIXER0>; > + iommus = <&iommu 0>; > > ports { > #address-cells = <1>; > @@ -155,6 +162,30 @@ > resets = <&ccu RST_BUS_VE>; > interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > allwinner,sram = <&ve_sram 1>; > + iommus = <&iommu 3>; > + }; > + > + gpu: gpu@1800000 { > + compatible = "allwinner,sun50i-h6-mali", > + "arm,mali-t720"; > + reg = <0x01800000 0x4000>; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "job", "mmu", "gpu"; > + clocks = <&ccu CLK_GPU>, <&ccu CLK_BUS_GPU>; > + clock-names = "core", "bus"; > + resets = <&ccu RST_BUS_GPU>; > + status = "disabled"; > + }; > + > + crypto: crypto@1904000 { > + compatible = "allwinner,sun50i-h6-crypto"; > + reg = <0x01904000 0x1000>; > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>, <&ccu CLK_MBUS_CE>; > + clock-names = "bus", "mod", "ram"; > + resets = <&ccu RST_BUS_CE>; > }; > > syscon: syscon@3000000 { > @@ -197,7 +228,7 @@ > ccu: clock@3001000 { > compatible = "allwinner,sun50i-h6-ccu"; > reg = <0x03001000 0x1000>; > - clocks = <&osc24M>, <&osc32k>, <&iosc>; > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > clock-names = "hosc", "losc", "iosc"; > #clock-cells = <1>; > #reset-cells = <1>; > @@ -215,9 +246,29 @@ > #dma-cells = <1>; > }; > > - sid: sid@3006000 { > + msgbox: mailbox@3003000 { > + compatible = "allwinner,sun50i-h6-msgbox", > + "allwinner,sun6i-a31-msgbox"; > + reg = <0x03003000 0x1000>; > + clocks = <&ccu CLK_BUS_MSGBOX>; > + resets = <&ccu RST_BUS_MSGBOX>; > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; > + #mbox-cells = <1>; > + }; > + > + sid: efuse@3006000 { > compatible = "allwinner,sun50i-h6-sid"; > reg = <0x03006000 0x400>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + ths_calibration: thermal-sensor-calibration@14 { > + reg = <0x14 0x8>; > + }; > + > + cpu_speed_grade: cpu-speed-grade@1c { > + reg = <0x1c 0x4>; > + }; > }; > > watchdog: watchdog@30090a0 { > @@ -225,10 +276,21 @@ > "allwinner,sun6i-a31-wdt"; > reg = <0x030090a0 0x20>; > interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&osc24M>; > /* Broken on some H6 boards */ > status = "disabled"; > }; > > + pwm: pwm@300a000 { > + compatible = "allwinner,sun50i-h6-pwm"; > + reg = <0x0300a000 0x400>; > + clocks = <&osc24M>, <&ccu CLK_BUS_PWM>; > + clock-names = "mod", "bus"; > + resets = <&ccu RST_BUS_PWM>; > + #pwm-cells = <3>; > + status = "disabled"; > + }; > + > pio: pinctrl@300b000 { > compatible = "allwinner,sun50i-h6-pinctrl"; > reg = <0x0300b000 0x400>; > @@ -236,7 +298,7 @@ > <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&ccu CLK_APB1>, <&osc24M>, <&osc32k>; > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>; > clock-names = "apb", "hosc", "losc"; > gpio-controller; > #gpio-cells = <3>; > @@ -256,6 +318,21 @@ > function = "hdmi"; > }; > > + i2c0_pins: i2c0-pins { > + pins = "PD25", "PD26"; > + function = "i2c0"; > + }; > + > + i2c1_pins: i2c1-pins { > + pins = "PH5", "PH6"; > + function = "i2c1"; > + }; > + > + i2c2_pins: i2c2-pins { > + pins = "PD23", "PD24"; > + function = "i2c2"; > + }; > + > mmc0_pins: mmc0-pins { > pins = "PF0", "PF1", "PF2", "PF3", > "PF4", "PF5"; > @@ -264,10 +341,7 @@ > bias-pull-up; > }; > > - /* > - * /omit-if-no-ref/ isn't supported by U-boot > - * keep this comment to avoid bad sync with Linux > - */ > + /omit-if-no-ref/ > mmc1_pins: mmc1-pins { > pins = "PG0", "PG1", "PG2", "PG3", > "PG4", "PG5"; > @@ -285,10 +359,50 @@ > bias-pull-up; > }; > > + /omit-if-no-ref/ > + spi0_pins: spi0-pins { > + pins = "PC0", "PC2", "PC3"; > + function = "spi0"; > + }; > + > + /* pin shared with MMC2-CMD (eMMC) */ > + /omit-if-no-ref/ > + spi0_cs_pin: spi0-cs-pin { > + pins = "PC5"; > + function = "spi0"; > + }; > + > + /omit-if-no-ref/ > + spi1_pins: spi1-pins { > + pins = "PH4", "PH5", "PH6"; > + function = "spi1"; > + }; > + > + /omit-if-no-ref/ > + spi1_cs_pin: spi1-cs-pin { > + pins = "PH3"; > + function = "spi1"; > + }; > + > + spdif_tx_pin: spdif-tx-pin { > + pins = "PH7"; > + function = "spdif"; > + }; > + > uart0_ph_pins: uart0-ph-pins { > pins = "PH0", "PH1"; > function = "uart0"; > }; > + > + uart1_pins: uart1-pins { > + pins = "PG6", "PG7"; > + function = "uart1"; > + }; > + > + uart1_rts_cts_pins: uart1-rts-cts-pins { > + pins = "PG8", "PG9"; > + function = "uart1"; > + }; > }; > > gic: interrupt-controller@3021000 { > @@ -302,6 +416,15 @@ > #interrupt-cells = <3>; > }; > > + iommu: iommu@30f0000 { > + compatible = "allwinner,sun50i-h6-iommu"; > + reg = <0x030f0000 0x10000>; > + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_IOMMU>; > + resets = <&ccu RST_BUS_IOMMU>; > + #iommu-cells = <1>; > + }; > + > mmc0: mmc@4020000 { > compatible = "allwinner,sun50i-h6-mmc", > "allwinner,sun50i-a64-mmc"; > @@ -394,6 +517,78 @@ > status = "disabled"; > }; > > + i2c0: i2c@5002000 { > + compatible = "allwinner,sun50i-h6-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002000 0x400>; > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C0>; > + resets = <&ccu RST_BUS_I2C0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c1: i2c@5002400 { > + compatible = "allwinner,sun50i-h6-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002400 0x400>; > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C1>; > + resets = <&ccu RST_BUS_I2C1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + i2c2: i2c@5002800 { > + compatible = "allwinner,sun50i-h6-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x05002800 0x400>; > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2C2>; > + resets = <&ccu RST_BUS_I2C2>; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + spi0: spi@5010000 { > + compatible = "allwinner,sun50i-h6-spi", > + "allwinner,sun8i-h3-spi"; > + reg = <0x05010000 0x1000>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; > + clock-names = "ahb", "mod"; > + dmas = <&dma 22>, <&dma 22>; > + dma-names = "rx", "tx"; > + resets = <&ccu RST_BUS_SPI0>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + spi1: spi@5011000 { > + compatible = "allwinner,sun50i-h6-spi", > + "allwinner,sun8i-h3-spi"; > + reg = <0x05011000 0x1000>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; > + clock-names = "ahb", "mod"; > + dmas = <&dma 23>, <&dma 23>; > + dma-names = "rx", "tx"; > + resets = <&ccu RST_BUS_SPI1>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > emac: ethernet@5020000 { > compatible = "allwinner,sun50i-h6-emac", > "allwinner,sun50i-a64-emac"; > @@ -414,6 +609,34 @@ > }; > }; > > + i2s1: i2s@5091000 { > + #sound-dai-cells = <0>; > + compatible = "allwinner,sun50i-h6-i2s"; > + reg = <0x05091000 0x1000>; > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>; > + clock-names = "apb", "mod"; > + dmas = <&dma 4>, <&dma 4>; > + resets = <&ccu RST_BUS_I2S1>; > + dma-names = "rx", "tx"; > + status = "disabled"; > + }; > + > + spdif: spdif@5093000 { > + #sound-dai-cells = <0>; > + compatible = "allwinner,sun50i-h6-spdif"; > + reg = <0x05093000 0x400>; > + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; > + clock-names = "apb", "spdif"; > + resets = <&ccu RST_BUS_SPDIF>; > + dmas = <&dma 2>; > + dma-names = "tx"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spdif_tx_pin>; > + status = "disabled"; > + }; > + > usb2otg: usb@5100000 { > compatible = "allwinner,sun50i-h6-musb", > "allwinner,sun8i-a33-musb"; > @@ -470,6 +693,38 @@ > status = "disabled"; > }; > > + dwc3: usb@5200000 { > + compatible = "snps,dwc3"; > + reg = <0x05200000 0x10000>; > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_XHCI>, > + <&ccu CLK_BUS_XHCI>, > + <&rtc 0>; > + clock-names = "ref", "bus_early", "suspend"; > + resets = <&ccu RST_BUS_XHCI>; > + /* > + * The datasheet of the chip doesn't declare the > + * peripheral function, and there's no boards known > + * to have a USB Type-B port routed to the port. > + * In addition, no one has tested the peripheral > + * function yet. > + * So set the dr_mode to "host" in the DTSI file. > + */ > + dr_mode = "host"; > + phys = <&usb3phy>; > + phy-names = "usb3-phy"; > + status = "disabled"; > + }; > + > + usb3phy: phy@5210000 { > + compatible = "allwinner,sun50i-h6-usb3-phy"; > + reg = <0x5210000 0x10000>; > + clocks = <&ccu CLK_USB_PHY1>; > + resets = <&ccu RST_USB_PHY1>; > + #phy-cells = <0>; > + status = "disabled"; > + }; > + > ehci3: usb@5311000 { > compatible = "allwinner,sun50i-h6-ehci", "generic-ehci"; > reg = <0x05311000 0x100>; > @@ -480,6 +735,7 @@ > resets = <&ccu RST_BUS_OHCI3>, > <&ccu RST_BUS_EHCI3>; > phys = <&usb2phy 3>; > + phy-names = "usb"; > status = "disabled"; > }; > > @@ -491,6 +747,7 @@ > <&ccu CLK_USB_OHCI3>; > resets = <&ccu RST_BUS_OHCI3>; > phys = <&usb2phy 3>; > + phy-names = "usb"; > status = "disabled"; > }; > > @@ -507,7 +764,7 @@ > resets = <&ccu RST_BUS_HDMI_SUB>, <&ccu RST_BUS_HDCP>; > reset-names = "ctrl", "hdcp"; > phys = <&hdmi_phy>; > - phy-names = "hdmi-phy"; > + phy-names = "phy"; > pinctrl-names = "default"; > pinctrl-0 = <&hdmi_pins>; > status = "disabled"; > @@ -549,7 +806,6 @@ > "tcon-tv0"; > clock-output-names = "tcon-top-tv0"; > resets = <&ccu RST_BUS_TCON_TOP>; > - reset-names = "rst"; > #clock-cells = <1>; > > ports { > @@ -636,10 +892,19 @@ > }; > }; > > + rtc: rtc@7000000 { > + compatible = "allwinner,sun50i-h6-rtc"; > + reg = <0x07000000 0x400>; > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; > + clock-output-names = "osc32k", "osc32k-out", "iosc"; > + #clock-cells = <1>; > + }; > + > r_ccu: clock@7010000 { > compatible = "allwinner,sun50i-h6-r-ccu"; > reg = <0x07010000 0x400>; > - clocks = <&osc24M>, <&osc32k>, <&iosc>, > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > <&ccu CLK_PLL_PERIPH0>; > clock-names = "hosc", "losc", "iosc", "pll-periph"; > #clock-cells = <1>; > @@ -651,6 +916,7 @@ > "allwinner,sun6i-a31-wdt"; > reg = <0x07020400 0x20>; > interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&osc24M>; > }; > > r_intc: interrupt-controller@7021000 { > @@ -667,7 +933,7 @@ > reg = <0x07022000 0x400>; > interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&osc32k>; > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; > clock-names = "apb", "hosc", "losc"; > gpio-controller; > #gpio-cells = <3>; > @@ -678,10 +944,30 @@ > pins = "PL0", "PL1"; > function = "s_i2c"; > }; > + > + r_ir_rx_pin: r-ir-rx-pin { > + pins = "PL9"; > + function = "s_cir_rx"; > + }; > + }; > + > + r_ir: ir@7040000 { > + compatible = "allwinner,sun50i-h6-ir", > + "allwinner,sun6i-a31-ir"; > + reg = <0x07040000 0x400>; > + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&r_ccu CLK_R_APB1_IR>, > + <&r_ccu CLK_IR>; > + clock-names = "apb", "ir"; > + resets = <&r_ccu RST_R_APB1_IR>; > + pinctrl-names = "default"; > + pinctrl-0 = <&r_ir_rx_pin>; > + status = "disabled"; > }; > > r_i2c: i2c@7081400 { > - compatible = "allwinner,sun6i-a31-i2c"; > + compatible = "allwinner,sun50i-h6-i2c", > + "allwinner,sun6i-a31-i2c"; > reg = <0x07081400 0x400>; > interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&r_ccu CLK_R_APB2_I2C>; > @@ -692,5 +978,55 @@ > #address-cells = <1>; > #size-cells = <0>; > }; > + > + ths: thermal-sensor@5070400 { > + compatible = "allwinner,sun50i-h6-ths"; > + reg = <0x05070400 0x100>; > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_THS>; > + clock-names = "bus"; > + resets = <&ccu RST_BUS_THS>; > + nvmem-cells = <&ths_calibration>; > + nvmem-cell-names = "calibration"; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + thermal-zones { > + cpu-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&ths 0>; > + > + trips { > + cpu_alert: cpu-alert { > + temperature = <85000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + cpu-crit { > + temperature = <100000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu_alert>; > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + > + gpu-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&ths 1>; > + }; > }; > }; >
Dne sreda, 06. januar 2021 ob 16:41:02 CET je André Przywara napisal(a): > On 03/01/2021 10:00, Jernej Skrabec wrote: > > Updated H6 DT files are based on Linux 5.11-rc1 release. > > > > Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> > > That looks alright, but it seems like the OrangePi One Plus .dts is not > updated? I missed that one. Best regards, Jernej > > Cheers, > Andre > > > --- > > arch/arm/dts/sun50i-h6-beelink-gs1.dts | 70 +++- > > arch/arm/dts/sun50i-h6-cpu-opp.dtsi | 117 +++++++ > > arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 71 +++- > > arch/arm/dts/sun50i-h6-orangepi.dtsi | 72 +++- > > arch/arm/dts/sun50i-h6-pine-h64.dts | 102 ++++-- > > arch/arm/dts/sun50i-h6.dtsi | 394 ++++++++++++++++++++-- > > 6 files changed, 758 insertions(+), 68 deletions(-) > > create mode 100644 arch/arm/dts/sun50i-h6-cpu-opp.dtsi > > > > diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i- h6-beelink-gs1.dts > > index 0dc33c90dd60..7c9dbde645b5 100644 > > --- a/arch/arm/dts/sun50i-h6-beelink-gs1.dts > > +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts > > @@ -1,11 +1,10 @@ > > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > -/* > > - * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> > > - */ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> > > > > /dts-v1/; > > > > #include "sun50i-h6.dtsi" > > +#include "sun50i-h6-cpu-opp.dtsi" > > > > #include <dt-bindings/gpio/gpio.h> > > > > @@ -25,6 +24,7 @@ > > connector { > > compatible = "hdmi-connector"; > > type = "a"; > > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > > > > port { > > hdmi_con_in: endpoint { > > @@ -33,6 +33,13 @@ > > }; > > }; > > > > + ext_osc32k: ext_osc32k_clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <32768>; > > + clock-output-names = "ext_osc32k"; > > + }; > > + > > leds { > > compatible = "gpio-leds"; > > > > @@ -51,12 +58,38 @@ > > regulator-max-microvolt = <5000000>; > > regulator-always-on; > > }; > > + > > + sound-spdif { > > + compatible = "simple-audio-card"; > > + simple-audio-card,name = "sun50i-h6-spdif"; > > + > > + simple-audio-card,cpu { > > + sound-dai = <&spdif>; > > + }; > > + > > + simple-audio-card,codec { > > + sound-dai = <&spdif_out>; > > + }; > > + }; > > + > > + spdif_out: spdif-out { > > + #sound-dai-cells = <0>; > > + compatible = "linux,spdif-dit"; > > + }; > > +}; > > + > > +&cpu0 { > > + cpu-supply = <®_dcdca>; > > }; > > > > &de { > > status = "okay"; > > }; > > > > +&dwc3 { > > + status = "okay"; > > +}; > > + > > &ehci0 { > > status = "okay"; > > }; > > @@ -64,12 +97,17 @@ > > &emac { > > pinctrl-names = "default"; > > pinctrl-0 = <&ext_rgmii_pins>; > > - phy-mode = "rgmii"; > > + phy-mode = "rgmii-id"; > > phy-handle = <&ext_rgmii_phy>; > > phy-supply = <®_aldo2>; > > status = "okay"; > > }; > > > > +&gpu { > > + mali-supply = <®_dcdcc>; > > + status = "okay"; > > +}; > > + > > &hdmi { > > status = "okay"; > > }; > > @@ -201,13 +239,16 @@ > > reg_dcdca: dcdca { > > regulator-always-on; > > regulator-min-microvolt = <810000>; > > - regulator-max-microvolt = <1080000>; > > + regulator-max-microvolt = <1160000>; > > + regulator-ramp-delay = <2500>; > > regulator-name = "vdd-cpu"; > > }; > > > > reg_dcdcc: dcdcc { > > + regulator-enable-ramp-delay = <32000>; > > regulator-min-microvolt = <810000>; > > regulator-max-microvolt = <1080000>; > > + regulator-ramp-delay = <2500>; > > regulator-name = "vdd-gpu"; > > }; > > > > @@ -232,6 +273,11 @@ > > }; > > }; > > > > +&r_ir { > > + linux,rc-map-name = "rc-beelink-gs1"; > > + status = "okay"; > > +}; > > + > > &r_pio { > > /* > > * PL0 and PL1 are used for PMIC I2C > > @@ -243,6 +289,14 @@ > > vcc-pm-supply = <®_aldo1>; > > }; > > > > +&rtc { > > + clocks = <&ext_osc32k>; > > +}; > > + > > +&spdif { > > + status = "okay"; > > +}; > > + > > &uart0 { > > pinctrl-names = "default"; > > pinctrl-0 = <&uart0_ph_pins>; > > @@ -258,3 +312,7 @@ > > usb0_vbus-supply = <®_vcc5v>; > > status = "okay"; > > }; > > + > > +&usb3phy { > > + status = "okay"; > > +}; > > diff --git a/arch/arm/dts/sun50i-h6-cpu-opp.dtsi b/arch/arm/dts/sun50i-h6- cpu-opp.dtsi > > new file mode 100644 > > index 000000000000..1a5eddc5a40f > > --- /dev/null > > +++ b/arch/arm/dts/sun50i-h6-cpu-opp.dtsi > > @@ -0,0 +1,117 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > > +// Copyright (C) 2020 Clément Péron <peron.clem@gmail.com> > > + > > +/ { > > + cpu_opp_table: cpu-opp-table { > > + compatible = "allwinner,sun50i-h6-operating-points"; > > + nvmem-cells = <&cpu_speed_grade>; > > + opp-shared; > > + > > + opp@480000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <480000000>; > > + > > + opp-microvolt-speed0 = <880000 880000 1200000>; > > + opp-microvolt-speed1 = <820000 820000 1200000>; > > + opp-microvolt-speed2 = <820000 820000 1200000>; > > + }; > > + > > + opp@720000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <720000000>; > > + > > + opp-microvolt-speed0 = <880000 880000 1200000>; > > + opp-microvolt-speed1 = <820000 820000 1200000>; > > + opp-microvolt-speed2 = <820000 820000 1200000>; > > + }; > > + > > + opp@816000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <816000000>; > > + > > + opp-microvolt-speed0 = <880000 880000 1200000>; > > + opp-microvolt-speed1 = <820000 820000 1200000>; > > + opp-microvolt-speed2 = <820000 820000 1200000>; > > + }; > > + > > + opp@888000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <888000000>; > > + > > + opp-microvolt-speed0 = <880000 880000 1200000>; > > + opp-microvolt-speed1 = <820000 820000 1200000>; > > + opp-microvolt-speed2 = <820000 820000 1200000>; > > + }; > > + > > + opp@1080000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1080000000>; > > + > > + opp-microvolt-speed0 = <940000 940000 1200000>; > > + opp-microvolt-speed1 = <880000 880000 1200000>; > > + opp-microvolt-speed2 = <880000 880000 1200000>; > > + }; > > + > > + opp@1320000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1320000000>; > > + > > + opp-microvolt-speed0 = <1000000 1000000 1200000>; > > + opp-microvolt-speed1 = <940000 940000 1200000>; > > + opp-microvolt-speed2 = <940000 940000 1200000>; > > + }; > > + > > + opp@1488000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1488000000>; > > + > > + opp-microvolt-speed0 = <1060000 1060000 1200000>; > > + opp-microvolt-speed1 = <1000000 1000000 1200000>; > > + opp-microvolt-speed2 = <1000000 1000000 1200000>; > > + }; > > + > > + opp@1608000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1608000000>; > > + > > + opp-microvolt-speed0 = <1090000 1090000 1200000>; > > + opp-microvolt-speed1 = <1030000 1030000 1200000>; > > + opp-microvolt-speed2 = <1030000 1030000 1200000>; > > + }; > > + > > + opp@1704000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1704000000>; > > + > > + opp-microvolt-speed0 = <1120000 1120000 1200000>; > > + opp-microvolt-speed1 = <1060000 1060000 1200000>; > > + opp-microvolt-speed2 = <1060000 1060000 1200000>; > > + }; > > + > > + opp@1800000000 { > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + opp-hz = /bits/ 64 <1800000000>; > > + > > + opp-microvolt-speed0 = <1160000 1160000 1200000>; > > + opp-microvolt-speed1 = <1100000 1100000 1200000>; > > + opp-microvolt-speed2 = <1100000 1100000 1200000>; > > + }; > > + }; > > +}; > > + > > +&cpu0 { > > + operating-points-v2 = <&cpu_opp_table>; > > +}; > > + > > +&cpu1 { > > + operating-points-v2 = <&cpu_opp_table>; > > +}; > > + > > +&cpu2 { > > + operating-points-v2 = <&cpu_opp_table>; > > +}; > > + > > +&cpu3 { > > + operating-points-v2 = <&cpu_opp_table>; > > +}; > > diff --git a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts b/arch/arm/dts/ sun50i-h6-orangepi-lite2.dts > > index e098a2475f2d..e8770858b5d0 100644 > > --- a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts > > +++ b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts > > @@ -1,11 +1,74 @@ > > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > -/* > > - * Copyright (C) 2018 Jagan Teki <jagan@openedev.com> > > - */ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2018 Jagan Teki <jagan@openedev.com> > > > > #include "sun50i-h6-orangepi.dtsi" > > > > / { > > model = "OrangePi Lite2"; > > compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6"; > > + > > + aliases { > > + serial1 = &uart1; /* BT-UART */ > > + }; > > + > > + wifi_pwrseq: wifi_pwrseq { > > + compatible = "mmc-pwrseq-simple"; > > + clocks = <&rtc 1>; > > + clock-names = "ext_clock"; > > + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ > > + post-power-on-delay-ms = <200>; > > + }; > > +}; > > + > > +&mmc1 { > > + vmmc-supply = <®_cldo2>; > > + vqmmc-supply = <®_bldo3>; > > + mmc-pwrseq = <&wifi_pwrseq>; > > + bus-width = <4>; > > + non-removable; > > + status = "okay"; > > + > > + brcm: sdio-wifi@1 { > > + reg = <1>; > > + compatible = "brcm,bcm4329-fmac"; > > + interrupt-parent = <&r_pio>; > > + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ > > + interrupt-names = "host-wake"; > > + }; > > +}; > > + > > +®_cldo2 { > > + /* > > + * This regulator is connected with CLDO3. > > + * Before the kernel can support synchronized > > + * enable of coupled regulators, keep them > > + * both always on as a ugly hack. > > + */ > > + regulator-always-on; > > +}; > > + > > +®_cldo3 { > > + /* > > + * This regulator is connected with CLDO2. > > + * See the comments for CLDO2. > > + */ > > + regulator-always-on; > > +}; > > + > > +/* There's the BT part of the AP6255 connected to that UART */ > > +&uart1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; > > + uart-has-rtscts; > > + status = "okay"; > > + > > + bluetooth { > > + compatible = "brcm,bcm4345c5"; > > + clocks = <&rtc 1>; > > + clock-names = "lpo"; > > + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ > > + host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ > > + shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ > > + max-speed = <1500000>; > > + }; > > }; > > diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6- orangepi.dtsi > > index 62e27948a3fa..ebc120a9232f 100644 > > --- a/arch/arm/dts/sun50i-h6-orangepi.dtsi > > +++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi > > @@ -1,8 +1,6 @@ > > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > -/* > > - * Copyright (C) 2018 Amarula Solutions > > - * Author: Jagan Teki <jagan@amarulasolutions.com> > > - */ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2018 Amarula Solutions > > +// Author: Jagan Teki <jagan@amarulasolutions.com> > > > > /dts-v1/; > > > > @@ -22,6 +20,25 @@ > > stdout-path = "serial0:115200n8"; > > }; > > > > + connector { > > + compatible = "hdmi-connector"; > > + type = "a"; > > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > > + > > + port { > > + hdmi_con_in: endpoint { > > + remote-endpoint = <&hdmi_out_con>; > > + }; > > + }; > > + }; > > + > > + ext_osc32k: ext_osc32k_clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <32768>; > > + clock-output-names = "ext_osc32k"; > > + }; > > + > > leds { > > compatible = "gpio-leds"; > > > > @@ -47,6 +64,10 @@ > > }; > > }; > > > > +&de { > > + status = "okay"; > > +}; > > + > > &ehci0 { > > status = "okay"; > > }; > > @@ -55,6 +76,21 @@ > > status = "okay"; > > }; > > > > +&gpu { > > + mali-supply = <®_dcdcc>; > > + status = "okay"; > > +}; > > + > > +&hdmi { > > + status = "okay"; > > +}; > > + > > +&hdmi_out { > > + hdmi_out_con: endpoint { > > + remote-endpoint = <&hdmi_con_in>; > > + }; > > +}; > > + > > &mmc0 { > > vmmc-supply = <®_cldo1>; > > cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; > > @@ -70,6 +106,12 @@ > > status = "okay"; > > }; > > > > +&pio { > > + vcc-pc-supply = <®_bldo2>; > > + vcc-pd-supply = <®_cldo1>; > > + vcc-pg-supply = <®_aldo1>; > > +}; > > + > > &r_i2c { > > status = "okay"; > > > > @@ -163,6 +205,7 @@ > > }; > > > > reg_dcdcc: dcdcc { > > + regulator-enable-ramp-delay = <32000>; > > regulator-min-microvolt = <810000>; > > regulator-max-microvolt = <1080000>; > > regulator-name = "vdd-gpu"; > > @@ -189,6 +232,18 @@ > > }; > > }; > > > > +&r_ir { > > + status = "okay"; > > +}; > > + > > +&r_pio { > > + vcc-pm-supply = <®_bldo3>; > > +}; > > + > > +&rtc { > > + clocks = <&ext_osc32k>; > > +}; > > + > > &uart0 { > > pinctrl-names = "default"; > > pinctrl-0 = <&uart0_ph_pins>; > > @@ -196,7 +251,12 @@ > > }; > > > > &usb2otg { > > - dr_mode = "otg"; > > + /* > > + * OrangePi Lite 2 and One Plus, where this DT is used, don't > > + * have a controllable VBUS even though they do have an ID pin. > > + * Using it as anything but a USB host is unsafe. > > + */ > > + dr_mode = "host"; > > status = "okay"; > > }; > > > > diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts b/arch/arm/dts/sun50i-h6- pine-h64.dts > > index 189834518391..961732c52aa0 100644 > > --- a/arch/arm/dts/sun50i-h6-pine-h64.dts > > +++ b/arch/arm/dts/sun50i-h6-pine-h64.dts > > @@ -1,30 +1,38 @@ > > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > -/* > > - * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> > > - */ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > /dts-v1/; > > > > #include "sun50i-h6.dtsi" > > +#include "sun50i-h6-cpu-opp.dtsi" > > > > #include <dt-bindings/gpio/gpio.h> > > > > / { > > - model = "Pine H64"; > > + model = "Pine H64 model A"; > > compatible = "pine64,pine-h64", "allwinner,sun50i-h6"; > > > > aliases { > > ethernet0 = &emac; > > serial0 = &uart0; > > + spi0 = &spi0; > > }; > > > > chosen { > > stdout-path = "serial0:115200n8"; > > }; > > > > - connector { > > + ext_osc32k: ext_osc32k_clk { > > + #clock-cells = <0>; > > + compatible = "fixed-clock"; > > + clock-frequency = <32768>; > > + clock-output-names = "ext_osc32k"; > > + }; > > + > > + hdmi_connector: connector { > > compatible = "hdmi-connector"; > > type = "a"; > > + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ > > > > port { > > hdmi_con_in: endpoint { > > @@ -52,6 +60,16 @@ > > }; > > }; > > > > + reg_gmac_3v3: gmac-3v3 { > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-gmac-3v3"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + startup-delay-us = <100000>; > > + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > reg_usb_vbus: vbus { > > compatible = "regulator-fixed"; > > regulator-name = "usb-vbus"; > > @@ -63,25 +81,35 @@ > > }; > > }; > > > > +&cpu0 { > > + cpu-supply = <®_dcdca>; > > +}; > > + > > +&de { > > + status = "okay"; > > +}; > > + > > +&ehci0 { > > + status = "okay"; > > +}; > > + > > +&ehci3 { > > + status = "okay"; > > +}; > > + > > &emac { > > pinctrl-names = "default"; > > pinctrl-0 = <&ext_rgmii_pins>; > > - phy-mode = "rgmii"; > > + phy-mode = "rgmii-id"; > > phy-handle = <&ext_rgmii_phy>; > > - phy-supply = <®_aldo2>; > > + phy-supply = <®_gmac_3v3>; > > allwinner,rx-delay-ps = <200>; > > allwinner,tx-delay-ps = <200>; > > status = "okay"; > > }; > > > > -&mdio { > > - ext_rgmii_phy: ethernet-phy@1 { > > - compatible = "ethernet-phy-ieee802.3-c22"; > > - reg = <1>; > > - }; > > -}; > > - > > -&de { > > +&gpu { > > + mali-supply = <®_dcdcc>; > > status = "okay"; > > }; > > > > @@ -95,12 +123,11 @@ > > }; > > }; > > > > -&ehci0 { > > - status = "okay"; > > -}; > > - > > -&ehci3 { > > - status = "okay"; > > +&mdio { > > + ext_rgmii_phy: ethernet-phy@1 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > }; > > > > &mmc0 { > > @@ -216,13 +243,16 @@ > > reg_dcdca: dcdca { > > regulator-always-on; > > regulator-min-microvolt = <810000>; > > - regulator-max-microvolt = <1080000>; > > + regulator-max-microvolt = <1160000>; > > + regulator-ramp-delay = <2500>; > > regulator-name = "vdd-cpu"; > > }; > > > > reg_dcdcc: dcdcc { > > + regulator-enable-ramp-delay = <32000>; > > regulator-min-microvolt = <810000>; > > regulator-max-microvolt = <1080000>; > > + regulator-ramp-delay = <2500>; > > regulator-name = "vdd-gpu"; > > }; > > > > @@ -255,10 +285,36 @@ > > }; > > }; > > > > +&r_ir { > > + status = "okay"; > > +}; > > + > > &r_pio { > > vcc-pm-supply = <®_aldo1>; > > }; > > > > +&rtc { > > + clocks = <&ext_osc32k>; > > +}; > > + > > +/* > > + * The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI > > + * flash and eMMC at the same time, as one of them would fail probing. > > + * Disable SPI0 in here, to prefer the more useful eMMC. U-Boot can > > + * fix this up in no eMMC is connected. > > + */ > > +&spi0 { > > + pinctrl-0 = <&spi0_pins>, <&spi0_cs_pin>; > > + pinctrl-names = "default"; > > + status = "disabled"; > > + > > + flash@0 { > > + compatible = "winbond,w25q128", "jedec,spi-nor"; > > + reg = <0>; > > + spi-max-frequency = <4000000>; > > + }; > > +}; > > + > > &uart0 { > > pinctrl-names = "default"; > > pinctrl-0 = <&uart0_ph_pins>; > > diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi > > index a117f479ae55..8a62a9fbe347 100644 > > --- a/arch/arm/dts/sun50i-h6.dtsi > > +++ b/arch/arm/dts/sun50i-h6.dtsi > > @@ -1,7 +1,5 @@ > > -// SPDX-License-Identifier: (GPL-2.0+ or MIT) > > -/* > > - * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > - */ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> > > > > #include <dt-bindings/interrupt-controller/arm-gic.h> > > #include <dt-bindings/clock/sun50i-h6-ccu.h> > > @@ -11,6 +9,7 @@ > > #include <dt-bindings/reset/sun50i-h6-ccu.h> > > #include <dt-bindings/reset/sun50i-h6-r-ccu.h> > > #include <dt-bindings/reset/sun8i-de2.h> > > +#include <dt-bindings/thermal/thermal.h> > > > > / { > > interrupt-parent = <&gic>; > > @@ -26,6 +25,9 @@ > > device_type = "cpu"; > > reg = <0>; > > enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + #cooling-cells = <2>; > > }; > > > > cpu1: cpu@1 { > > @@ -33,6 +35,9 @@ > > device_type = "cpu"; > > reg = <1>; > > enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + #cooling-cells = <2>; > > }; > > > > cpu2: cpu@2 { > > @@ -40,6 +45,9 @@ > > device_type = "cpu"; > > reg = <2>; > > enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + #cooling-cells = <2>; > > }; > > > > cpu3: cpu@3 { > > @@ -47,6 +55,9 @@ > > device_type = "cpu"; > > reg = <3>; > > enable-method = "psci"; > > + clocks = <&ccu CLK_CPUX>; > > + clock-latency-ns = <244144>; /* 8 32k periods */ > > + #cooling-cells = <2>; > > }; > > }; > > > > @@ -56,14 +67,6 @@ > > status = "disabled"; > > }; > > > > - iosc: internal-osc-clk { > > - #clock-cells = <0>; > > - compatible = "fixed-clock"; > > - clock-frequency = <16000000>; > > - clock-accuracy = <300000000>; > > - clock-output-names = "iosc"; > > - }; > > - > > osc24M: osc24M_clk { > > #clock-cells = <0>; > > compatible = "fixed-clock"; > > @@ -71,11 +74,13 @@ > > clock-output-names = "osc24M"; > > }; > > > > - osc32k: osc32k_clk { > > - #clock-cells = <0>; > > - compatible = "fixed-clock"; > > - clock-frequency = <32768>; > > - clock-output-names = "osc32k"; > > + pmu { > > + compatible = "arm,cortex-a53-pmu"; > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > > }; > > > > psci { > > @@ -85,6 +90,7 @@ > > > > timer { > > compatible = "arm,armv8-timer"; > > + arm,no-tick-in-suspend; > > interrupts = <GIC_PPI 13 > > (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, > > <GIC_PPI 14 > > @@ -130,6 +136,7 @@ > > clock-names = "bus", > > "mod"; > > resets = <&display_clocks RST_MIXER0>; > > + iommus = <&iommu 0>; > > > > ports { > > #address-cells = <1>; > > @@ -155,6 +162,30 @@ > > resets = <&ccu RST_BUS_VE>; > > interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > > allwinner,sram = <&ve_sram 1>; > > + iommus = <&iommu 3>; > > + }; > > + > > + gpu: gpu@1800000 { > > + compatible = "allwinner,sun50i-h6-mali", > > + "arm,mali-t720"; > > + reg = <0x01800000 0x4000>; > > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "job", "mmu", "gpu"; > > + clocks = <&ccu CLK_GPU>, <&ccu CLK_BUS_GPU>; > > + clock-names = "core", "bus"; > > + resets = <&ccu RST_BUS_GPU>; > > + status = "disabled"; > > + }; > > + > > + crypto: crypto@1904000 { > > + compatible = "allwinner,sun50i-h6-crypto"; > > + reg = <0x01904000 0x1000>; > > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>, <&ccu CLK_MBUS_CE>; > > + clock-names = "bus", "mod", "ram"; > > + resets = <&ccu RST_BUS_CE>; > > }; > > > > syscon: syscon@3000000 { > > @@ -197,7 +228,7 @@ > > ccu: clock@3001000 { > > compatible = "allwinner,sun50i-h6-ccu"; > > reg = <0x03001000 0x1000>; > > - clocks = <&osc24M>, <&osc32k>, <&iosc>; > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; > > clock-names = "hosc", "losc", "iosc"; > > #clock-cells = <1>; > > #reset-cells = <1>; > > @@ -215,9 +246,29 @@ > > #dma-cells = <1>; > > }; > > > > - sid: sid@3006000 { > > + msgbox: mailbox@3003000 { > > + compatible = "allwinner,sun50i-h6-msgbox", > > + "allwinner,sun6i-a31- msgbox"; > > + reg = <0x03003000 0x1000>; > > + clocks = <&ccu CLK_BUS_MSGBOX>; > > + resets = <&ccu RST_BUS_MSGBOX>; > > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; > > + #mbox-cells = <1>; > > + }; > > + > > + sid: efuse@3006000 { > > compatible = "allwinner,sun50i-h6-sid"; > > reg = <0x03006000 0x400>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + ths_calibration: thermal-sensor- calibration@14 { > > + reg = <0x14 0x8>; > > + }; > > + > > + cpu_speed_grade: cpu-speed-grade@1c { > > + reg = <0x1c 0x4>; > > + }; > > }; > > > > watchdog: watchdog@30090a0 { > > @@ -225,10 +276,21 @@ > > "allwinner,sun6i-a31-wdt"; > > reg = <0x030090a0 0x20>; > > interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&osc24M>; > > /* Broken on some H6 boards */ > > status = "disabled"; > > }; > > > > + pwm: pwm@300a000 { > > + compatible = "allwinner,sun50i-h6-pwm"; > > + reg = <0x0300a000 0x400>; > > + clocks = <&osc24M>, <&ccu CLK_BUS_PWM>; > > + clock-names = "mod", "bus"; > > + resets = <&ccu RST_BUS_PWM>; > > + #pwm-cells = <3>; > > + status = "disabled"; > > + }; > > + > > pio: pinctrl@300b000 { > > compatible = "allwinner,sun50i-h6-pinctrl"; > > reg = <0x0300b000 0x400>; > > @@ -236,7 +298,7 @@ > > <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, > > <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, > > <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&ccu CLK_APB1>, <&osc24M>, <&osc32k>; > > + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>; > > clock-names = "apb", "hosc", "losc"; > > gpio-controller; > > #gpio-cells = <3>; > > @@ -256,6 +318,21 @@ > > function = "hdmi"; > > }; > > > > + i2c0_pins: i2c0-pins { > > + pins = "PD25", "PD26"; > > + function = "i2c0"; > > + }; > > + > > + i2c1_pins: i2c1-pins { > > + pins = "PH5", "PH6"; > > + function = "i2c1"; > > + }; > > + > > + i2c2_pins: i2c2-pins { > > + pins = "PD23", "PD24"; > > + function = "i2c2"; > > + }; > > + > > mmc0_pins: mmc0-pins { > > pins = "PF0", "PF1", "PF2", "PF3", > > "PF4", "PF5"; > > @@ -264,10 +341,7 @@ > > bias-pull-up; > > }; > > > > - /* > > - * /omit-if-no-ref/ isn't supported by U- boot > > - * keep this comment to avoid bad sync with Linux > > - */ > > + /omit-if-no-ref/ > > mmc1_pins: mmc1-pins { > > pins = "PG0", "PG1", "PG2", "PG3", > > "PG4", "PG5"; > > @@ -285,10 +359,50 @@ > > bias-pull-up; > > }; > > > > + /omit-if-no-ref/ > > + spi0_pins: spi0-pins { > > + pins = "PC0", "PC2", "PC3"; > > + function = "spi0"; > > + }; > > + > > + /* pin shared with MMC2-CMD (eMMC) */ > > + /omit-if-no-ref/ > > + spi0_cs_pin: spi0-cs-pin { > > + pins = "PC5"; > > + function = "spi0"; > > + }; > > + > > + /omit-if-no-ref/ > > + spi1_pins: spi1-pins { > > + pins = "PH4", "PH5", "PH6"; > > + function = "spi1"; > > + }; > > + > > + /omit-if-no-ref/ > > + spi1_cs_pin: spi1-cs-pin { > > + pins = "PH3"; > > + function = "spi1"; > > + }; > > + > > + spdif_tx_pin: spdif-tx-pin { > > + pins = "PH7"; > > + function = "spdif"; > > + }; > > + > > uart0_ph_pins: uart0-ph-pins { > > pins = "PH0", "PH1"; > > function = "uart0"; > > }; > > + > > + uart1_pins: uart1-pins { > > + pins = "PG6", "PG7"; > > + function = "uart1"; > > + }; > > + > > + uart1_rts_cts_pins: uart1-rts-cts-pins { > > + pins = "PG8", "PG9"; > > + function = "uart1"; > > + }; > > }; > > > > gic: interrupt-controller@3021000 { > > @@ -302,6 +416,15 @@ > > #interrupt-cells = <3>; > > }; > > > > + iommu: iommu@30f0000 { > > + compatible = "allwinner,sun50i-h6-iommu"; > > + reg = <0x030f0000 0x10000>; > > + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_IOMMU>; > > + resets = <&ccu RST_BUS_IOMMU>; > > + #iommu-cells = <1>; > > + }; > > + > > mmc0: mmc@4020000 { > > compatible = "allwinner,sun50i-h6-mmc", > > "allwinner,sun50i-a64-mmc"; > > @@ -394,6 +517,78 @@ > > status = "disabled"; > > }; > > > > + i2c0: i2c@5002000 { > > + compatible = "allwinner,sun50i-h6-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002000 0x400>; > > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C0>; > > + resets = <&ccu RST_BUS_I2C0>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c0_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c1: i2c@5002400 { > > + compatible = "allwinner,sun50i-h6-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002400 0x400>; > > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C1>; > > + resets = <&ccu RST_BUS_I2C1>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + i2c2: i2c@5002800 { > > + compatible = "allwinner,sun50i-h6-i2c", > > + "allwinner,sun6i-a31-i2c"; > > + reg = <0x05002800 0x400>; > > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2C2>; > > + resets = <&ccu RST_BUS_I2C2>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi0: spi@5010000 { > > + compatible = "allwinner,sun50i-h6-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05010000 0x1000>; > > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; > > + clock-names = "ahb", "mod"; > > + dmas = <&dma 22>, <&dma 22>; > > + dma-names = "rx", "tx"; > > + resets = <&ccu RST_BUS_SPI0>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + spi1: spi@5011000 { > > + compatible = "allwinner,sun50i-h6-spi", > > + "allwinner,sun8i-h3-spi"; > > + reg = <0x05011000 0x1000>; > > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; > > + clock-names = "ahb", "mod"; > > + dmas = <&dma 23>, <&dma 23>; > > + dma-names = "rx", "tx"; > > + resets = <&ccu RST_BUS_SPI1>; > > + status = "disabled"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > emac: ethernet@5020000 { > > compatible = "allwinner,sun50i-h6-emac", > > "allwinner,sun50i-a64-emac"; > > @@ -414,6 +609,34 @@ > > }; > > }; > > > > + i2s1: i2s@5091000 { > > + #sound-dai-cells = <0>; > > + compatible = "allwinner,sun50i-h6-i2s"; > > + reg = <0x05091000 0x1000>; > > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>; > > + clock-names = "apb", "mod"; > > + dmas = <&dma 4>, <&dma 4>; > > + resets = <&ccu RST_BUS_I2S1>; > > + dma-names = "rx", "tx"; > > + status = "disabled"; > > + }; > > + > > + spdif: spdif@5093000 { > > + #sound-dai-cells = <0>; > > + compatible = "allwinner,sun50i-h6-spdif"; > > + reg = <0x05093000 0x400>; > > + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; > > + clock-names = "apb", "spdif"; > > + resets = <&ccu RST_BUS_SPDIF>; > > + dmas = <&dma 2>; > > + dma-names = "tx"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&spdif_tx_pin>; > > + status = "disabled"; > > + }; > > + > > usb2otg: usb@5100000 { > > compatible = "allwinner,sun50i-h6-musb", > > "allwinner,sun8i-a33-musb"; > > @@ -470,6 +693,38 @@ > > status = "disabled"; > > }; > > > > + dwc3: usb@5200000 { > > + compatible = "snps,dwc3"; > > + reg = <0x05200000 0x10000>; > > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_XHCI>, > > + <&ccu CLK_BUS_XHCI>, > > + <&rtc 0>; > > + clock-names = "ref", "bus_early", "suspend"; > > + resets = <&ccu RST_BUS_XHCI>; > > + /* > > + * The datasheet of the chip doesn't declare the > > + * peripheral function, and there's no boards known > > + * to have a USB Type-B port routed to the port. > > + * In addition, no one has tested the peripheral > > + * function yet. > > + * So set the dr_mode to "host" in the DTSI file. > > + */ > > + dr_mode = "host"; > > + phys = <&usb3phy>; > > + phy-names = "usb3-phy"; > > + status = "disabled"; > > + }; > > + > > + usb3phy: phy@5210000 { > > + compatible = "allwinner,sun50i-h6-usb3-phy"; > > + reg = <0x5210000 0x10000>; > > + clocks = <&ccu CLK_USB_PHY1>; > > + resets = <&ccu RST_USB_PHY1>; > > + #phy-cells = <0>; > > + status = "disabled"; > > + }; > > + > > ehci3: usb@5311000 { > > compatible = "allwinner,sun50i-h6-ehci", "generic-ehci"; > > reg = <0x05311000 0x100>; > > @@ -480,6 +735,7 @@ > > resets = <&ccu RST_BUS_OHCI3>, > > <&ccu RST_BUS_EHCI3>; > > phys = <&usb2phy 3>; > > + phy-names = "usb"; > > status = "disabled"; > > }; > > > > @@ -491,6 +747,7 @@ > > <&ccu CLK_USB_OHCI3>; > > resets = <&ccu RST_BUS_OHCI3>; > > phys = <&usb2phy 3>; > > + phy-names = "usb"; > > status = "disabled"; > > }; > > > > @@ -507,7 +764,7 @@ > > resets = <&ccu RST_BUS_HDMI_SUB>, <&ccu RST_BUS_HDCP>; > > reset-names = "ctrl", "hdcp"; > > phys = <&hdmi_phy>; > > - phy-names = "hdmi-phy"; > > + phy-names = "phy"; > > pinctrl-names = "default"; > > pinctrl-0 = <&hdmi_pins>; > > status = "disabled"; > > @@ -549,7 +806,6 @@ > > "tcon-tv0"; > > clock-output-names = "tcon-top-tv0"; > > resets = <&ccu RST_BUS_TCON_TOP>; > > - reset-names = "rst"; > > #clock-cells = <1>; > > > > ports { > > @@ -636,10 +892,19 @@ > > }; > > }; > > > > + rtc: rtc@7000000 { > > + compatible = "allwinner,sun50i-h6-rtc"; > > + reg = <0x07000000 0x400>; > > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; > > + clock-output-names = "osc32k", "osc32k-out", "iosc"; > > + #clock-cells = <1>; > > + }; > > + > > r_ccu: clock@7010000 { > > compatible = "allwinner,sun50i-h6-r-ccu"; > > reg = <0x07010000 0x400>; > > - clocks = <&osc24M>, <&osc32k>, <&iosc>, > > + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, > > <&ccu CLK_PLL_PERIPH0>; > > clock-names = "hosc", "losc", "iosc", "pll- periph"; > > #clock-cells = <1>; > > @@ -651,6 +916,7 @@ > > "allwinner,sun6i-a31-wdt"; > > reg = <0x07020400 0x20>; > > interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&osc24M>; > > }; > > > > r_intc: interrupt-controller@7021000 { > > @@ -667,7 +933,7 @@ > > reg = <0x07022000 0x400>; > > interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, > > <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&osc32k>; > > + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; > > clock-names = "apb", "hosc", "losc"; > > gpio-controller; > > #gpio-cells = <3>; > > @@ -678,10 +944,30 @@ > > pins = "PL0", "PL1"; > > function = "s_i2c"; > > }; > > + > > + r_ir_rx_pin: r-ir-rx-pin { > > + pins = "PL9"; > > + function = "s_cir_rx"; > > + }; > > + }; > > + > > + r_ir: ir@7040000 { > > + compatible = "allwinner,sun50i- h6-ir", > > + "allwinner,sun6i- a31-ir"; > > + reg = <0x07040000 0x400>; > > + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&r_ccu CLK_R_APB1_IR>, > > + <&r_ccu CLK_IR>; > > + clock-names = "apb", "ir"; > > + resets = <&r_ccu RST_R_APB1_IR>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&r_ir_rx_pin>; > > + status = "disabled"; > > }; > > > > r_i2c: i2c@7081400 { > > - compatible = "allwinner,sun6i-a31-i2c"; > > + compatible = "allwinner,sun50i-h6-i2c", > > + "allwinner,sun6i-a31-i2c"; > > reg = <0x07081400 0x400>; > > interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; > > clocks = <&r_ccu CLK_R_APB2_I2C>; > > @@ -692,5 +978,55 @@ > > #address-cells = <1>; > > #size-cells = <0>; > > }; > > + > > + ths: thermal-sensor@5070400 { > > + compatible = "allwinner,sun50i-h6-ths"; > > + reg = <0x05070400 0x100>; > > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&ccu CLK_BUS_THS>; > > + clock-names = "bus"; > > + resets = <&ccu RST_BUS_THS>; > > + nvmem-cells = <&ths_calibration>; > > + nvmem-cell-names = "calibration"; > > + #thermal-sensor-cells = <1>; > > + }; > > + }; > > + > > + thermal-zones { > > + cpu-thermal { > > + polling-delay-passive = <0>; > > + polling-delay = <0>; > > + thermal-sensors = <&ths 0>; > > + > > + trips { > > + cpu_alert: cpu-alert { > > + temperature = <85000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + > > + cpu-crit { > > + temperature = <100000>; > > + hysteresis = <0>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = <&cpu_alert>; > > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + > > + gpu-thermal { > > + polling-delay-passive = <0>; > > + polling-delay = <0>; > > + thermal-sensors = <&ths 1>; > > + }; > > }; > > }; > > > >
diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts index 0dc33c90dd60..7c9dbde645b5 100644 --- a/arch/arm/dts/sun50i-h6-beelink-gs1.dts +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts @@ -1,11 +1,10 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2019 Clément Péron <peron.clem@gmail.com> /dts-v1/; #include "sun50i-h6.dtsi" +#include "sun50i-h6-cpu-opp.dtsi" #include <dt-bindings/gpio/gpio.h> @@ -25,6 +24,7 @@ connector { compatible = "hdmi-connector"; type = "a"; + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ port { hdmi_con_in: endpoint { @@ -33,6 +33,13 @@ }; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds"; @@ -51,12 +58,38 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + sound-spdif { + compatible = "simple-audio-card"; + simple-audio-card,name = "sun50i-h6-spdif"; + + simple-audio-card,cpu { + sound-dai = <&spdif>; + }; + + simple-audio-card,codec { + sound-dai = <&spdif_out>; + }; + }; + + spdif_out: spdif-out { + #sound-dai-cells = <0>; + compatible = "linux,spdif-dit"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdca>; }; &de { status = "okay"; }; +&dwc3 { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -64,12 +97,17 @@ &emac { pinctrl-names = "default"; pinctrl-0 = <&ext_rgmii_pins>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; phy-handle = <&ext_rgmii_phy>; phy-supply = <®_aldo2>; status = "okay"; }; +&gpu { + mali-supply = <®_dcdcc>; + status = "okay"; +}; + &hdmi { status = "okay"; }; @@ -201,13 +239,16 @@ reg_dcdca: dcdca { regulator-always-on; regulator-min-microvolt = <810000>; - regulator-max-microvolt = <1080000>; + regulator-max-microvolt = <1160000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-cpu"; }; reg_dcdcc: dcdcc { + regulator-enable-ramp-delay = <32000>; regulator-min-microvolt = <810000>; regulator-max-microvolt = <1080000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-gpu"; }; @@ -232,6 +273,11 @@ }; }; +&r_ir { + linux,rc-map-name = "rc-beelink-gs1"; + status = "okay"; +}; + &r_pio { /* * PL0 and PL1 are used for PMIC I2C @@ -243,6 +289,14 @@ vcc-pm-supply = <®_aldo1>; }; +&rtc { + clocks = <&ext_osc32k>; +}; + +&spdif { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; @@ -258,3 +312,7 @@ usb0_vbus-supply = <®_vcc5v>; status = "okay"; }; + +&usb3phy { + status = "okay"; +}; diff --git a/arch/arm/dts/sun50i-h6-cpu-opp.dtsi b/arch/arm/dts/sun50i-h6-cpu-opp.dtsi new file mode 100644 index 000000000000..1a5eddc5a40f --- /dev/null +++ b/arch/arm/dts/sun50i-h6-cpu-opp.dtsi @@ -0,0 +1,117 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> +// Copyright (C) 2020 Clément Péron <peron.clem@gmail.com> + +/ { + cpu_opp_table: cpu-opp-table { + compatible = "allwinner,sun50i-h6-operating-points"; + nvmem-cells = <&cpu_speed_grade>; + opp-shared; + + opp@480000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <480000000>; + + opp-microvolt-speed0 = <880000 880000 1200000>; + opp-microvolt-speed1 = <820000 820000 1200000>; + opp-microvolt-speed2 = <820000 820000 1200000>; + }; + + opp@720000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <720000000>; + + opp-microvolt-speed0 = <880000 880000 1200000>; + opp-microvolt-speed1 = <820000 820000 1200000>; + opp-microvolt-speed2 = <820000 820000 1200000>; + }; + + opp@816000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <816000000>; + + opp-microvolt-speed0 = <880000 880000 1200000>; + opp-microvolt-speed1 = <820000 820000 1200000>; + opp-microvolt-speed2 = <820000 820000 1200000>; + }; + + opp@888000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <888000000>; + + opp-microvolt-speed0 = <880000 880000 1200000>; + opp-microvolt-speed1 = <820000 820000 1200000>; + opp-microvolt-speed2 = <820000 820000 1200000>; + }; + + opp@1080000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1080000000>; + + opp-microvolt-speed0 = <940000 940000 1200000>; + opp-microvolt-speed1 = <880000 880000 1200000>; + opp-microvolt-speed2 = <880000 880000 1200000>; + }; + + opp@1320000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1320000000>; + + opp-microvolt-speed0 = <1000000 1000000 1200000>; + opp-microvolt-speed1 = <940000 940000 1200000>; + opp-microvolt-speed2 = <940000 940000 1200000>; + }; + + opp@1488000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1488000000>; + + opp-microvolt-speed0 = <1060000 1060000 1200000>; + opp-microvolt-speed1 = <1000000 1000000 1200000>; + opp-microvolt-speed2 = <1000000 1000000 1200000>; + }; + + opp@1608000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1608000000>; + + opp-microvolt-speed0 = <1090000 1090000 1200000>; + opp-microvolt-speed1 = <1030000 1030000 1200000>; + opp-microvolt-speed2 = <1030000 1030000 1200000>; + }; + + opp@1704000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1704000000>; + + opp-microvolt-speed0 = <1120000 1120000 1200000>; + opp-microvolt-speed1 = <1060000 1060000 1200000>; + opp-microvolt-speed2 = <1060000 1060000 1200000>; + }; + + opp@1800000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1800000000>; + + opp-microvolt-speed0 = <1160000 1160000 1200000>; + opp-microvolt-speed1 = <1100000 1100000 1200000>; + opp-microvolt-speed2 = <1100000 1100000 1200000>; + }; + }; +}; + +&cpu0 { + operating-points-v2 = <&cpu_opp_table>; +}; + +&cpu1 { + operating-points-v2 = <&cpu_opp_table>; +}; + +&cpu2 { + operating-points-v2 = <&cpu_opp_table>; +}; + +&cpu3 { + operating-points-v2 = <&cpu_opp_table>; +}; diff --git a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts index e098a2475f2d..e8770858b5d0 100644 --- a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts +++ b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts @@ -1,11 +1,74 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (C) 2018 Jagan Teki <jagan@openedev.com> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2018 Jagan Teki <jagan@openedev.com> #include "sun50i-h6-orangepi.dtsi" / { model = "OrangePi Lite2"; compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6"; + + aliases { + serial1 = &uart1; /* BT-UART */ + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&rtc 1>; + clock-names = "ext_clock"; + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ + post-power-on-delay-ms = <200>; + }; +}; + +&mmc1 { + vmmc-supply = <®_cldo2>; + vqmmc-supply = <®_bldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcm: sdio-wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ + interrupt-names = "host-wake"; + }; +}; + +®_cldo2 { + /* + * This regulator is connected with CLDO3. + * Before the kernel can support synchronized + * enable of coupled regulators, keep them + * both always on as a ugly hack. + */ + regulator-always-on; +}; + +®_cldo3 { + /* + * This regulator is connected with CLDO2. + * See the comments for CLDO2. + */ + regulator-always-on; +}; + +/* There's the BT part of the AP6255 connected to that UART */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4345c5"; + clocks = <&rtc 1>; + clock-names = "lpo"; + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ + host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ + shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ + max-speed = <1500000>; + }; }; diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6-orangepi.dtsi index 62e27948a3fa..ebc120a9232f 100644 --- a/arch/arm/dts/sun50i-h6-orangepi.dtsi +++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi @@ -1,8 +1,6 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (C) 2018 Amarula Solutions - * Author: Jagan Teki <jagan@amarulasolutions.com> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2018 Amarula Solutions +// Author: Jagan Teki <jagan@amarulasolutions.com> /dts-v1/; @@ -22,6 +20,25 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds"; @@ -47,6 +64,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -55,6 +76,21 @@ status = "okay"; }; +&gpu { + mali-supply = <®_dcdcc>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; @@ -70,6 +106,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + &r_i2c { status = "okay"; @@ -163,6 +205,7 @@ }; reg_dcdcc: dcdcc { + regulator-enable-ramp-delay = <32000>; regulator-min-microvolt = <810000>; regulator-max-microvolt = <1080000>; regulator-name = "vdd-gpu"; @@ -189,6 +232,18 @@ }; }; +&r_ir { + status = "okay"; +}; + +&r_pio { + vcc-pm-supply = <®_bldo3>; +}; + +&rtc { + clocks = <&ext_osc32k>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; @@ -196,7 +251,12 @@ }; &usb2otg { - dr_mode = "otg"; + /* + * OrangePi Lite 2 and One Plus, where this DT is used, don't + * have a controllable VBUS even though they do have an ID pin. + * Using it as anything but a USB host is unsafe. + */ + dr_mode = "host"; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts b/arch/arm/dts/sun50i-h6-pine-h64.dts index 189834518391..961732c52aa0 100644 --- a/arch/arm/dts/sun50i-h6-pine-h64.dts +++ b/arch/arm/dts/sun50i-h6-pine-h64.dts @@ -1,30 +1,38 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io> /dts-v1/; #include "sun50i-h6.dtsi" +#include "sun50i-h6-cpu-opp.dtsi" #include <dt-bindings/gpio/gpio.h> / { - model = "Pine H64"; + model = "Pine H64 model A"; compatible = "pine64,pine-h64", "allwinner,sun50i-h6"; aliases { ethernet0 = &emac; serial0 = &uart0; + spi0 = &spi0; }; chosen { stdout-path = "serial0:115200n8"; }; - connector { + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + + hdmi_connector: connector { compatible = "hdmi-connector"; type = "a"; + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ port { hdmi_con_in: endpoint { @@ -52,6 +60,16 @@ }; }; + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc-gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + reg_usb_vbus: vbus { compatible = "regulator-fixed"; regulator-name = "usb-vbus"; @@ -63,25 +81,35 @@ }; }; +&cpu0 { + cpu-supply = <®_dcdca>; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + &emac { pinctrl-names = "default"; pinctrl-0 = <&ext_rgmii_pins>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; phy-handle = <&ext_rgmii_phy>; - phy-supply = <®_aldo2>; + phy-supply = <®_gmac_3v3>; allwinner,rx-delay-ps = <200>; allwinner,tx-delay-ps = <200>; status = "okay"; }; -&mdio { - ext_rgmii_phy: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; -}; - -&de { +&gpu { + mali-supply = <®_dcdcc>; status = "okay"; }; @@ -95,12 +123,11 @@ }; }; -&ehci0 { - status = "okay"; -}; - -&ehci3 { - status = "okay"; +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; }; &mmc0 { @@ -216,13 +243,16 @@ reg_dcdca: dcdca { regulator-always-on; regulator-min-microvolt = <810000>; - regulator-max-microvolt = <1080000>; + regulator-max-microvolt = <1160000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-cpu"; }; reg_dcdcc: dcdcc { + regulator-enable-ramp-delay = <32000>; regulator-min-microvolt = <810000>; regulator-max-microvolt = <1080000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-gpu"; }; @@ -255,10 +285,36 @@ }; }; +&r_ir { + status = "okay"; +}; + &r_pio { vcc-pm-supply = <®_aldo1>; }; +&rtc { + clocks = <&ext_osc32k>; +}; + +/* + * The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI + * flash and eMMC at the same time, as one of them would fail probing. + * Disable SPI0 in here, to prefer the more useful eMMC. U-Boot can + * fix this up in no eMMC is connected. + */ +&spi0 { + pinctrl-0 = <&spi0_pins>, <&spi0_cs_pin>; + pinctrl-names = "default"; + status = "disabled"; + + flash@0 { + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <4000000>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi index a117f479ae55..8a62a9fbe347 100644 --- a/arch/arm/dts/sun50i-h6.dtsi +++ b/arch/arm/dts/sun50i-h6.dtsi @@ -1,7 +1,5 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/sun50i-h6-ccu.h> @@ -11,6 +9,7 @@ #include <dt-bindings/reset/sun50i-h6-ccu.h> #include <dt-bindings/reset/sun50i-h6-r-ccu.h> #include <dt-bindings/reset/sun8i-de2.h> +#include <dt-bindings/thermal/thermal.h> / { interrupt-parent = <&gic>; @@ -26,6 +25,9 @@ device_type = "cpu"; reg = <0>; enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + #cooling-cells = <2>; }; cpu1: cpu@1 { @@ -33,6 +35,9 @@ device_type = "cpu"; reg = <1>; enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + #cooling-cells = <2>; }; cpu2: cpu@2 { @@ -40,6 +45,9 @@ device_type = "cpu"; reg = <2>; enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + #cooling-cells = <2>; }; cpu3: cpu@3 { @@ -47,6 +55,9 @@ device_type = "cpu"; reg = <3>; enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + #cooling-cells = <2>; }; }; @@ -56,14 +67,6 @@ status = "disabled"; }; - iosc: internal-osc-clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <16000000>; - clock-accuracy = <300000000>; - clock-output-names = "iosc"; - }; - osc24M: osc24M_clk { #clock-cells = <0>; compatible = "fixed-clock"; @@ -71,11 +74,13 @@ clock-output-names = "osc24M"; }; - osc32k: osc32k_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; - clock-output-names = "osc32k"; + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; }; psci { @@ -85,6 +90,7 @@ timer { compatible = "arm,armv8-timer"; + arm,no-tick-in-suspend; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, <GIC_PPI 14 @@ -130,6 +136,7 @@ clock-names = "bus", "mod"; resets = <&display_clocks RST_MIXER0>; + iommus = <&iommu 0>; ports { #address-cells = <1>; @@ -155,6 +162,30 @@ resets = <&ccu RST_BUS_VE>; interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; allwinner,sram = <&ve_sram 1>; + iommus = <&iommu 3>; + }; + + gpu: gpu@1800000 { + compatible = "allwinner,sun50i-h6-mali", + "arm,mali-t720"; + reg = <0x01800000 0x4000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&ccu CLK_GPU>, <&ccu CLK_BUS_GPU>; + clock-names = "core", "bus"; + resets = <&ccu RST_BUS_GPU>; + status = "disabled"; + }; + + crypto: crypto@1904000 { + compatible = "allwinner,sun50i-h6-crypto"; + reg = <0x01904000 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>, <&ccu CLK_MBUS_CE>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CE>; }; syscon: syscon@3000000 { @@ -197,7 +228,7 @@ ccu: clock@3001000 { compatible = "allwinner,sun50i-h6-ccu"; reg = <0x03001000 0x1000>; - clocks = <&osc24M>, <&osc32k>, <&iosc>; + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>; clock-names = "hosc", "losc", "iosc"; #clock-cells = <1>; #reset-cells = <1>; @@ -215,9 +246,29 @@ #dma-cells = <1>; }; - sid: sid@3006000 { + msgbox: mailbox@3003000 { + compatible = "allwinner,sun50i-h6-msgbox", + "allwinner,sun6i-a31-msgbox"; + reg = <0x03003000 0x1000>; + clocks = <&ccu CLK_BUS_MSGBOX>; + resets = <&ccu RST_BUS_MSGBOX>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + }; + + sid: efuse@3006000 { compatible = "allwinner,sun50i-h6-sid"; reg = <0x03006000 0x400>; + #address-cells = <1>; + #size-cells = <1>; + + ths_calibration: thermal-sensor-calibration@14 { + reg = <0x14 0x8>; + }; + + cpu_speed_grade: cpu-speed-grade@1c { + reg = <0x1c 0x4>; + }; }; watchdog: watchdog@30090a0 { @@ -225,10 +276,21 @@ "allwinner,sun6i-a31-wdt"; reg = <0x030090a0 0x20>; interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&osc24M>; /* Broken on some H6 boards */ status = "disabled"; }; + pwm: pwm@300a000 { + compatible = "allwinner,sun50i-h6-pwm"; + reg = <0x0300a000 0x400>; + clocks = <&osc24M>, <&ccu CLK_BUS_PWM>; + clock-names = "mod", "bus"; + resets = <&ccu RST_BUS_PWM>; + #pwm-cells = <3>; + status = "disabled"; + }; + pio: pinctrl@300b000 { compatible = "allwinner,sun50i-h6-pinctrl"; reg = <0x0300b000 0x400>; @@ -236,7 +298,7 @@ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_APB1>, <&osc24M>, <&osc32k>; + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>; clock-names = "apb", "hosc", "losc"; gpio-controller; #gpio-cells = <3>; @@ -256,6 +318,21 @@ function = "hdmi"; }; + i2c0_pins: i2c0-pins { + pins = "PD25", "PD26"; + function = "i2c0"; + }; + + i2c1_pins: i2c1-pins { + pins = "PH5", "PH6"; + function = "i2c1"; + }; + + i2c2_pins: i2c2-pins { + pins = "PD23", "PD24"; + function = "i2c2"; + }; + mmc0_pins: mmc0-pins { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; @@ -264,10 +341,7 @@ bias-pull-up; }; - /* - * /omit-if-no-ref/ isn't supported by U-boot - * keep this comment to avoid bad sync with Linux - */ + /omit-if-no-ref/ mmc1_pins: mmc1-pins { pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; @@ -285,10 +359,50 @@ bias-pull-up; }; + /omit-if-no-ref/ + spi0_pins: spi0-pins { + pins = "PC0", "PC2", "PC3"; + function = "spi0"; + }; + + /* pin shared with MMC2-CMD (eMMC) */ + /omit-if-no-ref/ + spi0_cs_pin: spi0-cs-pin { + pins = "PC5"; + function = "spi0"; + }; + + /omit-if-no-ref/ + spi1_pins: spi1-pins { + pins = "PH4", "PH5", "PH6"; + function = "spi1"; + }; + + /omit-if-no-ref/ + spi1_cs_pin: spi1-cs-pin { + pins = "PH3"; + function = "spi1"; + }; + + spdif_tx_pin: spdif-tx-pin { + pins = "PH7"; + function = "spdif"; + }; + uart0_ph_pins: uart0-ph-pins { pins = "PH0", "PH1"; function = "uart0"; }; + + uart1_pins: uart1-pins { + pins = "PG6", "PG7"; + function = "uart1"; + }; + + uart1_rts_cts_pins: uart1-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; + }; }; gic: interrupt-controller@3021000 { @@ -302,6 +416,15 @@ #interrupt-cells = <3>; }; + iommu: iommu@30f0000 { + compatible = "allwinner,sun50i-h6-iommu"; + reg = <0x030f0000 0x10000>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_IOMMU>; + resets = <&ccu RST_BUS_IOMMU>; + #iommu-cells = <1>; + }; + mmc0: mmc@4020000 { compatible = "allwinner,sun50i-h6-mmc", "allwinner,sun50i-a64-mmc"; @@ -394,6 +517,78 @@ status = "disabled"; }; + i2c0: i2c@5002000 { + compatible = "allwinner,sun50i-h6-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002000 0x400>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@5002400 { + compatible = "allwinner,sun50i-h6-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002400 0x400>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@5002800 { + compatible = "allwinner,sun50i-h6-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x05002800 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi0: spi@5010000 { + compatible = "allwinner,sun50i-h6-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05010000 0x1000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; + clock-names = "ahb", "mod"; + dmas = <&dma 22>, <&dma 22>; + dma-names = "rx", "tx"; + resets = <&ccu RST_BUS_SPI0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@5011000 { + compatible = "allwinner,sun50i-h6-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05011000 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + resets = <&ccu RST_BUS_SPI1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + emac: ethernet@5020000 { compatible = "allwinner,sun50i-h6-emac", "allwinner,sun50i-a64-emac"; @@ -414,6 +609,34 @@ }; }; + i2s1: i2s@5091000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun50i-h6-i2s"; + reg = <0x05091000 0x1000>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>; + clock-names = "apb", "mod"; + dmas = <&dma 4>, <&dma 4>; + resets = <&ccu RST_BUS_I2S1>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + spdif: spdif@5093000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun50i-h6-spdif"; + reg = <0x05093000 0x400>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; + clock-names = "apb", "spdif"; + resets = <&ccu RST_BUS_SPDIF>; + dmas = <&dma 2>; + dma-names = "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&spdif_tx_pin>; + status = "disabled"; + }; + usb2otg: usb@5100000 { compatible = "allwinner,sun50i-h6-musb", "allwinner,sun8i-a33-musb"; @@ -470,6 +693,38 @@ status = "disabled"; }; + dwc3: usb@5200000 { + compatible = "snps,dwc3"; + reg = <0x05200000 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_XHCI>, + <&ccu CLK_BUS_XHCI>, + <&rtc 0>; + clock-names = "ref", "bus_early", "suspend"; + resets = <&ccu RST_BUS_XHCI>; + /* + * The datasheet of the chip doesn't declare the + * peripheral function, and there's no boards known + * to have a USB Type-B port routed to the port. + * In addition, no one has tested the peripheral + * function yet. + * So set the dr_mode to "host" in the DTSI file. + */ + dr_mode = "host"; + phys = <&usb3phy>; + phy-names = "usb3-phy"; + status = "disabled"; + }; + + usb3phy: phy@5210000 { + compatible = "allwinner,sun50i-h6-usb3-phy"; + reg = <0x5210000 0x10000>; + clocks = <&ccu CLK_USB_PHY1>; + resets = <&ccu RST_USB_PHY1>; + #phy-cells = <0>; + status = "disabled"; + }; + ehci3: usb@5311000 { compatible = "allwinner,sun50i-h6-ehci", "generic-ehci"; reg = <0x05311000 0x100>; @@ -480,6 +735,7 @@ resets = <&ccu RST_BUS_OHCI3>, <&ccu RST_BUS_EHCI3>; phys = <&usb2phy 3>; + phy-names = "usb"; status = "disabled"; }; @@ -491,6 +747,7 @@ <&ccu CLK_USB_OHCI3>; resets = <&ccu RST_BUS_OHCI3>; phys = <&usb2phy 3>; + phy-names = "usb"; status = "disabled"; }; @@ -507,7 +764,7 @@ resets = <&ccu RST_BUS_HDMI_SUB>, <&ccu RST_BUS_HDCP>; reset-names = "ctrl", "hdcp"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; pinctrl-names = "default"; pinctrl-0 = <&hdmi_pins>; status = "disabled"; @@ -549,7 +806,6 @@ "tcon-tv0"; clock-output-names = "tcon-top-tv0"; resets = <&ccu RST_BUS_TCON_TOP>; - reset-names = "rst"; #clock-cells = <1>; ports { @@ -636,10 +892,19 @@ }; }; + rtc: rtc@7000000 { + compatible = "allwinner,sun50i-h6-rtc"; + reg = <0x07000000 0x400>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + clock-output-names = "osc32k", "osc32k-out", "iosc"; + #clock-cells = <1>; + }; + r_ccu: clock@7010000 { compatible = "allwinner,sun50i-h6-r-ccu"; reg = <0x07010000 0x400>; - clocks = <&osc24M>, <&osc32k>, <&iosc>, + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, <&ccu CLK_PLL_PERIPH0>; clock-names = "hosc", "losc", "iosc", "pll-periph"; #clock-cells = <1>; @@ -651,6 +916,7 @@ "allwinner,sun6i-a31-wdt"; reg = <0x07020400 0x20>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&osc24M>; }; r_intc: interrupt-controller@7021000 { @@ -667,7 +933,7 @@ reg = <0x07022000 0x400>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&osc32k>; + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; clock-names = "apb", "hosc", "losc"; gpio-controller; #gpio-cells = <3>; @@ -678,10 +944,30 @@ pins = "PL0", "PL1"; function = "s_i2c"; }; + + r_ir_rx_pin: r-ir-rx-pin { + pins = "PL9"; + function = "s_cir_rx"; + }; + }; + + r_ir: ir@7040000 { + compatible = "allwinner,sun50i-h6-ir", + "allwinner,sun6i-a31-ir"; + reg = <0x07040000 0x400>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB1_IR>, + <&r_ccu CLK_IR>; + clock-names = "apb", "ir"; + resets = <&r_ccu RST_R_APB1_IR>; + pinctrl-names = "default"; + pinctrl-0 = <&r_ir_rx_pin>; + status = "disabled"; }; r_i2c: i2c@7081400 { - compatible = "allwinner,sun6i-a31-i2c"; + compatible = "allwinner,sun50i-h6-i2c", + "allwinner,sun6i-a31-i2c"; reg = <0x07081400 0x400>; interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_R_APB2_I2C>; @@ -692,5 +978,55 @@ #address-cells = <1>; #size-cells = <0>; }; + + ths: thermal-sensor@5070400 { + compatible = "allwinner,sun50i-h6-ths"; + reg = <0x05070400 0x100>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_THS>; + clock-names = "bus"; + resets = <&ccu RST_BUS_THS>; + nvmem-cells = <&ths_calibration>; + nvmem-cell-names = "calibration"; + #thermal-sensor-cells = <1>; + }; + }; + + thermal-zones { + cpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&ths 0>; + + trips { + cpu_alert: cpu-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu-crit { + temperature = <100000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + gpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&ths 1>; + }; }; };
Updated H6 DT files are based on Linux 5.11-rc1 release. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> --- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 70 +++- arch/arm/dts/sun50i-h6-cpu-opp.dtsi | 117 +++++++ arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 71 +++- arch/arm/dts/sun50i-h6-orangepi.dtsi | 72 +++- arch/arm/dts/sun50i-h6-pine-h64.dts | 102 ++++-- arch/arm/dts/sun50i-h6.dtsi | 394 ++++++++++++++++++++-- 6 files changed, 758 insertions(+), 68 deletions(-) create mode 100644 arch/arm/dts/sun50i-h6-cpu-opp.dtsi