@@ -38,9 +38,6 @@ config TARGET_IPEK01
config TARGET_JUPITER
bool "Support jupiter"
-config TARGET_MCC200
- bool "Support mcc200"
-
config TARGET_MOTIONPRO
bool "Support motionpro"
@@ -130,7 +127,6 @@ source "board/jupiter/Kconfig"
source "board/manroland/hmi1001/Kconfig"
source "board/manroland/mucmc52/Kconfig"
source "board/manroland/uc101/Kconfig"
-source "board/mcc200/Kconfig"
source "board/motionpro/Kconfig"
source "board/munices/Kconfig"
source "board/phytec/pcm030/Kconfig"
deleted file mode 100644
@@ -1,9 +0,0 @@
-if TARGET_MCC200
-
-config SYS_BOARD
- default "mcc200"
-
-config SYS_CONFIG_NAME
- default "mcc200"
-
-endif
deleted file mode 100644
@@ -1,17 +0,0 @@
-MCC200 BOARD
-#M: -
-S: Maintained
-F: board/mcc200/
-F: include/configs/mcc200.h
-F: configs/mcc200_defconfig
-F: configs/mcc200_COM12_defconfig
-F: configs/mcc200_COM12_highboot_defconfig
-F: configs/mcc200_COM12_highboot_SDRAM_defconfig
-F: configs/mcc200_COM12_SDRAM_defconfig
-F: configs/mcc200_highboot_defconfig
-F: configs/mcc200_highboot_SDRAM_defconfig
-F: configs/mcc200_SDRAM_defconfig
-F: configs/prs200_defconfig
-F: configs/prs200_DDR_defconfig
-F: configs/prs200_highboot_defconfig
-F: configs/prs200_highboot_DDR_defconfig
deleted file mode 100644
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := mcc200.o lcd.o auto_update.o
deleted file mode 100644
@@ -1,521 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <image.h>
-#include <asm/byteorder.h>
-#include <usb.h>
-#include <part.h>
-
-#ifdef CONFIG_AUTO_UPDATE
-
-#ifndef CONFIG_USB_OHCI
-#error "must define CONFIG_USB_OHCI"
-#endif
-
-#ifndef CONFIG_USB_STORAGE
-#error "must define CONFIG_USB_STORAGE"
-#endif
-
-#ifndef CONFIG_SYS_HUSH_PARSER
-#error "must define CONFIG_SYS_HUSH_PARSER"
-#endif
-
-#if !defined(CONFIG_CMD_FAT)
-#error "must define CONFIG_CMD_FAT"
-#endif
-
-#undef AU_DEBUG
-
-#undef debug
-#ifdef AU_DEBUG
-#define debug(fmt,args...) printf (fmt ,##args)
-#else
-#define debug(fmt,args...)
-#endif /* AU_DEBUG */
-
-/* possible names of files on the USB stick. */
-#define AU_FIRMWARE "u-boot.img"
-#define AU_KERNEL "kernel.img"
-#define AU_ROOTFS "rootfs.img"
-
-struct flash_layout {
- long start;
- long end;
-};
-
-/* layout of the FLASH. ST = start address, ND = end address. */
-#define AU_FL_FIRMWARE_ST 0xfC000000
-#define AU_FL_FIRMWARE_ND 0xfC03FFFF
-#define AU_FL_KERNEL_ST 0xfC0C0000
-#define AU_FL_KERNEL_ND 0xfC1BFFFF
-#define AU_FL_ROOTFS_ST 0xFC1C0000
-#define AU_FL_ROOTFS_ND 0xFCFBFFFF
-
-static int au_usb_stor_curr_dev; /* current device */
-
-/* index of each file in the following arrays */
-#define IDX_FIRMWARE 0
-#define IDX_KERNEL 1
-#define IDX_ROOTFS 2
-
-/* max. number of files which could interest us */
-#define AU_MAXFILES 3
-
-/* pointers to file names */
-char *aufile[AU_MAXFILES] = {
- AU_FIRMWARE,
- AU_KERNEL,
- AU_ROOTFS
-};
-
-/* sizes of flash areas for each file */
-long ausize[AU_MAXFILES] = {
- (AU_FL_FIRMWARE_ND + 1) - AU_FL_FIRMWARE_ST,
- (AU_FL_KERNEL_ND + 1) - AU_FL_KERNEL_ST,
- (AU_FL_ROOTFS_ND + 1) - AU_FL_ROOTFS_ST,
-};
-
-/* array of flash areas start and end addresses */
-struct flash_layout aufl_layout[AU_MAXFILES] = {
- { AU_FL_FIRMWARE_ST, AU_FL_FIRMWARE_ND, },
- { AU_FL_KERNEL_ST, AU_FL_KERNEL_ND, },
- { AU_FL_ROOTFS_ST, AU_FL_ROOTFS_ND, },
-};
-
-ulong totsize;
-
-/* where to load files into memory */
-#define LOAD_ADDR ((unsigned char *)0x00200000)
-
-/* the root file system is the largest image */
-#define MAX_LOADSZ ausize[IDX_ROOTFS]
-
-/*i2c address of the keypad status*/
-#define I2C_PSOC_KEYPAD_ADDR 0x53
-
-/* keypad mask */
-#define KEYPAD_ROW 2
-#define KEYPAD_COL 2
-#define KEYPAD_MASK_LO ((1<<(KEYPAD_COL-1+(KEYPAD_ROW*3-3)))&0xFF)
-#define KEYPAD_MASK_HI ((1<<(KEYPAD_COL-1+(KEYPAD_ROW*3-3)))>>8)
-
-/* externals */
-extern int fat_register_device(block_dev_desc_t *, int);
-extern int file_fat_detectfs(void);
-extern long file_fat_read(const char *, void *, unsigned long);
-extern int i2c_read (unsigned char, unsigned int, int , unsigned char* , int);
-extern int flash_sect_erase(ulong, ulong);
-extern int flash_sect_protect (int, ulong, ulong);
-extern int flash_write (char *, ulong, ulong);
-extern int u_boot_hush_start(void);
-#ifdef CONFIG_PROGRESSBAR
-extern void show_progress(int, int);
-extern void lcd_puts (char *);
-extern void lcd_enable(void);
-#endif
-
-int au_check_cksum_valid(int idx, long nbytes)
-{
- image_header_t *hdr;
-
- hdr = (image_header_t *)LOAD_ADDR;
-#if defined(CONFIG_FIT)
- if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) {
- puts ("Non legacy image format not supported\n");
- return -1;
- }
-#endif
-
- if (nbytes != image_get_image_size (hdr)) {
- printf ("Image %s bad total SIZE\n", aufile[idx]);
- return -1;
- }
- /* check the data CRC */
- if (!image_check_dcrc (hdr)) {
- printf ("Image %s bad data checksum\n", aufile[idx]);
- return -1;
- }
- return 0;
-}
-
-int au_check_header_valid(int idx, long nbytes)
-{
- image_header_t *hdr;
- unsigned long checksum, fsize;
-
- hdr = (image_header_t *)LOAD_ADDR;
-#if defined(CONFIG_FIT)
- if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) {
- puts ("Non legacy image format not supported\n");
- return -1;
- }
-#endif
-
- /* check the easy ones first */
-#undef CHECK_VALID_DEBUG
-#ifdef CHECK_VALID_DEBUG
- printf("magic %#x %#x ", image_get_magic (hdr), IH_MAGIC);
- printf("arch %#x %#x ", image_get_arch (hdr), IH_ARCH_ARM);
- printf("size %#x %#lx ", image_get_data_size (hdr), nbytes);
- printf("type %#x %#x ", image_get_type (hdr), IH_TYPE_KERNEL);
-#endif
- if (nbytes < image_get_header_size ()) {
- printf ("Image %s bad header SIZE\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- if (!image_check_magic (hdr) || !image_check_arch (hdr, IH_ARCH_PPC)) {
- printf ("Image %s bad MAGIC or ARCH\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- /* check the hdr CRC */
- if (!image_check_hcrc (hdr)) {
- printf ("Image %s bad header checksum\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- /* check the type - could do this all in one gigantic if() */
- if ((idx == IDX_FIRMWARE) && !image_check_type (hdr, IH_TYPE_FIRMWARE)) {
- printf ("Image %s wrong type\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- if ((idx == IDX_KERNEL) && !image_check_type (hdr, IH_TYPE_KERNEL)) {
- printf ("Image %s wrong type\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- if ((idx == IDX_ROOTFS) &&
- (!image_check_type (hdr, IH_TYPE_RAMDISK) &&
- !image_check_type (hdr, IH_TYPE_FILESYSTEM))) {
- printf ("Image %s wrong type\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- /* recycle checksum */
- checksum = image_get_data_size (hdr);
-
- fsize = checksum + image_get_header_size ();
- /* for kernel and ramdisk the image header must also fit into flash */
- if (idx == IDX_KERNEL || image_check_type (hdr, IH_TYPE_RAMDISK))
- checksum += image_get_header_size ();
-
- /* check the size does not exceed space in flash. HUSH scripts */
- if ((ausize[idx] != 0) && (ausize[idx] < checksum)) {
- printf ("Image %s is bigger than FLASH\n", aufile[idx]);
- ausize[idx] = 0;
- return -1;
- }
- /* Update with the real filesize */
- ausize[idx] = fsize;
-
- return checksum; /* return size to be written to flash */
-}
-
-int au_do_update(int idx, long sz)
-{
- image_header_t *hdr;
- char *addr;
- long start, end;
- int off, rc;
- uint nbytes;
-
- hdr = (image_header_t *)LOAD_ADDR;
-#if defined(CONFIG_FIT)
- if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) {
- puts ("Non legacy image format not supported\n");
- return -1;
- }
-#endif
-
- /* execute a script */
- if (image_check_type (hdr, IH_TYPE_SCRIPT)) {
- addr = (char *)((char *)hdr + image_get_header_size ());
- /* stick a NULL at the end of the script, otherwise */
- /* parse_string_outer() runs off the end. */
- addr[image_get_data_size (hdr)] = 0;
- addr += 8;
- run_command_list(addr, -1, 0);
- return 0;
- }
-
- start = aufl_layout[idx].start;
- end = aufl_layout[idx].end;
-
- /* unprotect the address range */
- /* this assumes that ONLY the firmware is protected! */
- if (idx == IDX_FIRMWARE) {
-#undef AU_UPDATE_TEST
-#ifdef AU_UPDATE_TEST
- /* erase it where Linux goes */
- start = aufl_layout[1].start;
- end = aufl_layout[1].end;
-#endif
- flash_sect_protect(0, start, end);
- }
-
- /*
- * erase the address range.
- */
- debug ("flash_sect_erase(%lx, %lx);\n", start, end);
- flash_sect_erase(start, end);
- mdelay(100);
-#ifdef CONFIG_PROGRESSBAR
- show_progress(end - start, totsize);
-#endif
-
- /* strip the header - except for the kernel and ramdisk */
- if (image_check_type (hdr, IH_TYPE_KERNEL) ||
- image_check_type (hdr, IH_TYPE_RAMDISK)) {
- addr = (char *)hdr;
- off = image_get_header_size ();
- nbytes = image_get_image_size (hdr);
- } else {
- addr = (char *)((char *)hdr + image_get_header_size ());
-#ifdef AU_UPDATE_TEST
- /* copy it to where Linux goes */
- if (idx == IDX_FIRMWARE)
- start = aufl_layout[1].start;
-#endif
- off = 0;
- nbytes = image_get_data_size (hdr);
- }
-
- /* copy the data from RAM to FLASH */
- debug ("flash_write(%p, %lx %x)\n", addr, start, nbytes);
- rc = flash_write(addr, start, nbytes);
- if (rc != 0) {
- printf("Flashing failed due to error %d\n", rc);
- return -1;
- }
-
-#ifdef CONFIG_PROGRESSBAR
- show_progress(nbytes, totsize);
-#endif
-
- /* check the data CRC of the copy */
- if (crc32 (0, (uchar *)(start + off), image_get_data_size (hdr)) !=
- image_get_dcrc (hdr)) {
- printf ("Image %s Bad Data Checksum after COPY\n", aufile[idx]);
- return -1;
- }
-
- /* protect the address range */
- /* this assumes that ONLY the firmware is protected! */
- if (idx == IDX_FIRMWARE)
- flash_sect_protect(1, start, end);
- return 0;
-}
-
-/*
- * this is called from board_init() after the hardware has been set up
- * and is usable. That seems like a good time to do this.
- * Right now the return value is ignored.
- */
-int do_auto_update(void)
-{
- block_dev_desc_t *stor_dev;
- long sz;
- int i, res = 0, cnt, old_ctrlc;
- char *env;
- long start, end;
-
-#if 0 /* disable key-press detection to speed up boot-up time */
- uchar keypad_status1[2] = {0,0}, keypad_status2[2] = {0,0};
-
- /*
- * Read keypad status
- */
- i2c_read(I2C_PSOC_KEYPAD_ADDR, 0, 0, keypad_status1, 2);
- mdelay(500);
- i2c_read(I2C_PSOC_KEYPAD_ADDR, 0, 0, keypad_status2, 2);
-
- /*
- * Check keypad
- */
- if ( !(keypad_status1[1] & KEYPAD_MASK_LO) ||
- (keypad_status1[1] != keypad_status2[1])) {
- return 0;
- }
-
-#endif
- au_usb_stor_curr_dev = -1;
- /* start USB */
- if (usb_stop() < 0) {
- debug ("usb_stop failed\n");
- return -1;
- }
- if (usb_init() < 0) {
- debug ("usb_init failed\n");
- return -1;
- }
- /*
- * check whether a storage device is attached (assume that it's
- * a USB memory stick, since nothing else should be attached).
- */
- au_usb_stor_curr_dev = usb_stor_scan(0);
- if (au_usb_stor_curr_dev == -1) {
- debug ("No device found. Not initialized?\n");
- res = -1;
- goto xit;
- }
- /* check whether it has a partition table */
- stor_dev = get_dev("usb", 0);
- if (stor_dev == NULL) {
- debug ("uknown device type\n");
- res = -1;
- goto xit;
- }
- if (fat_register_device(stor_dev, 1) != 0) {
- debug ("Unable to use USB %d:%d for fatls\n",
- au_usb_stor_curr_dev, 1);
- res = -1;
- goto xit;
- }
- if (file_fat_detectfs() != 0) {
- debug ("file_fat_detectfs failed\n");
- }
-
- /*
- * now check whether start and end are defined using environment
- * variables.
- */
- start = -1;
- end = 0;
- env = getenv("firmware_st");
- if (env != NULL)
- start = simple_strtoul(env, NULL, 16);
- env = getenv("firmware_nd");
- if (env != NULL)
- end = simple_strtoul(env, NULL, 16);
- if (start >= 0 && end && end > start) {
- ausize[IDX_FIRMWARE] = (end + 1) - start;
- aufl_layout[IDX_FIRMWARE].start = start;
- aufl_layout[IDX_FIRMWARE].end = end;
- }
- start = -1;
- end = 0;
- env = getenv("kernel_st");
- if (env != NULL)
- start = simple_strtoul(env, NULL, 16);
- env = getenv("kernel_nd");
- if (env != NULL)
- end = simple_strtoul(env, NULL, 16);
- if (start >= 0 && end && end > start) {
- ausize[IDX_KERNEL] = (end + 1) - start;
- aufl_layout[IDX_KERNEL].start = start;
- aufl_layout[IDX_KERNEL].end = end;
- }
- start = -1;
- end = 0;
- env = getenv("rootfs_st");
- if (env != NULL)
- start = simple_strtoul(env, NULL, 16);
- env = getenv("rootfs_nd");
- if (env != NULL)
- end = simple_strtoul(env, NULL, 16);
- if (start >= 0 && end && end > start) {
- ausize[IDX_ROOTFS] = (end + 1) - start;
- aufl_layout[IDX_ROOTFS].start = start;
- aufl_layout[IDX_ROOTFS].end = end;
- }
-
- /* make certain that HUSH is runnable */
- u_boot_hush_start();
- /* make sure that we see CTRL-C and save the old state */
- old_ctrlc = disable_ctrlc(0);
-
- /* validate the images first */
- for (i = 0; i < AU_MAXFILES; i++) {
- ulong imsize;
- /* just read the header */
- sz = file_fat_read(aufile[i], LOAD_ADDR, image_get_header_size ());
- debug ("read %s sz %ld hdr %d\n",
- aufile[i], sz, image_get_header_size ());
- if (sz <= 0 || sz < image_get_header_size ()) {
- debug ("%s not found\n", aufile[i]);
- ausize[i] = 0;
- continue;
- }
- /* au_check_header_valid() updates ausize[] */
- if ((imsize = au_check_header_valid(i, sz)) < 0) {
- debug ("%s header not valid\n", aufile[i]);
- continue;
- }
- /* totsize accounts for image size and flash erase size */
- totsize += (imsize + (aufl_layout[i].end - aufl_layout[i].start));
- }
-
-#ifdef CONFIG_PROGRESSBAR
- if (totsize) {
- lcd_puts(" Update in progress\n");
- lcd_enable();
- }
-#endif
-
- /* just loop thru all the possible files */
- for (i = 0; i < AU_MAXFILES && totsize; i++) {
- if (!ausize[i]) {
- continue;
- }
- sz = file_fat_read(aufile[i], LOAD_ADDR, ausize[i]);
-
- debug ("read %s sz %ld hdr %d\n",
- aufile[i], sz, image_get_header_size ());
-
- if (sz != ausize[i]) {
- printf ("%s: size %ld read %ld?\n", aufile[i], ausize[i], sz);
- continue;
- }
-
- if (sz <= 0 || sz <= image_get_header_size ()) {
- debug ("%s not found\n", aufile[i]);
- continue;
- }
- if (au_check_cksum_valid(i, sz) < 0) {
- debug ("%s checksum not valid\n", aufile[i]);
- continue;
- }
- /* this is really not a good idea, but it's what the */
- /* customer wants. */
- cnt = 0;
- do {
- res = au_do_update(i, sz);
- /* let the user break out of the loop */
- if (ctrlc() || had_ctrlc()) {
- clear_ctrlc();
- break;
- }
- cnt++;
-#ifdef AU_TEST_ONLY
- } while (res < 0 && cnt < (AU_MAXFILES + 1));
- if (cnt < (AU_MAXFILES + 1))
-#else
- } while (res < 0);
-#endif
- }
-
- /* restore the old state */
- disable_ctrlc(old_ctrlc);
-#ifdef CONFIG_PROGRESSBAR
- if (totsize) {
- if (!res) {
- lcd_puts("\n Update completed\n");
- } else {
- lcd_puts("\n Update error\n");
- }
- lcd_enable();
- }
-#endif
- xit:
- usb_stop();
- return res;
-}
-#endif /* CONFIG_AUTO_UPDATE */
deleted file mode 100644
@@ -1,200 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <lcd.h>
-#include <mpc5xxx.h>
-#include <malloc.h>
-
-#ifdef CONFIG_LCD
-
-#undef SWAPPED_LCD /* For the previous h/w version */
-/*
- * The name of the device used for communication
- * with the PSoC.
- */
-#define PSOC_PSC MPC5XXX_PSC2
-#define PSOC_BAUD 230400UL
-
-#define RTS_ASSERT 1
-#define RTS_NEGATE 0
-#define CTS_ASSERT 1
-#define CTS_NEGATE 0
-
-/*
- * Dimensions in pixels
- */
-#define LCD_WIDTH 160
-#define LCD_HEIGHT 100
-
-/*
- * Dimensions in bytes
- */
-#define LCD_BUF_SIZE ((LCD_WIDTH*LCD_HEIGHT)>>3)
-
-#if LCD_BPP != LCD_MONOCHROME
-#error "MCC200 support only monochrome displays (1 bpp)!"
-#endif
-
-#define PSOC_RETRIES 10 /* each of PSOC_WAIT_TIME */
-#define PSOC_WAIT_TIME 10 /* usec */
-
-#include <video_font.h>
-#define FONT_WIDTH VIDEO_FONT_WIDTH
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * LCD information
- */
-vidinfo_t panel_info = {
- LCD_WIDTH, LCD_HEIGHT, LCD_BPP
-};
-
-
-/*
- * The device we use to communicate with PSoC
- */
-int serial_inited = 0;
-
-/*
- * Imported functions to support the PSoC protocol
- */
-extern int serial_init_dev (unsigned long dev_base);
-extern void serial_setrts_dev (unsigned long dev_base, int s);
-extern int serial_getcts_dev (unsigned long dev_base);
-extern void serial_putc_raw_dev(unsigned long dev_base, const char c);
-
-/*
- * Just stubs for our driver, needed for compiling compabilty with
- * the common LCD driver code.
- */
-void lcd_initcolregs (void)
-{
-}
-
-void lcd_ctrl_init (void *lcdbase)
-{
-}
-
-/*
- * Function sends the contents of the frame-buffer to the LCD
- */
-void lcd_enable (void)
-{
- int i, retries, fb_size;
-
- if (!serial_inited) {
- unsigned long baud;
-
- baud = gd->baudrate;
- gd->baudrate = PSOC_BAUD;
- serial_init_dev(PSOC_PSC);
- gd->baudrate = baud;
- serial_setrts_dev (PSOC_PSC, RTS_ASSERT);
- serial_inited = 1;
- }
-
- /*
- * Implement PSoC communication protocol:
- * 1. Assert RTS, wait CTS assertion
- * 2. Transmit data
- * 3. Negate RTS, wait CTS negation
- */
-
- /* 1 */
- serial_setrts_dev (PSOC_PSC, RTS_ASSERT);
- for (retries = PSOC_RETRIES; retries; retries--) {
- if (serial_getcts_dev(PSOC_PSC) == CTS_ASSERT)
- break;
- udelay (PSOC_WAIT_TIME);
- }
- if (!retries) {
- printf ("%s Error: PSoC doesn't respond on "
- "RTS ASSERT\n", __FUNCTION__);
- }
-
- /* 2 */
- fb_size = panel_info.vl_row * (panel_info.vl_col >> 3);
-
-#if !defined(SWAPPED_LCD)
- for (i=0; i<fb_size; i++) {
- serial_putc_raw_dev(PSOC_PSC, ((char *)gd->fb_base)[i]);
- }
-#else
- {
- int x, y, pwidth;
- char *p = (char *)gd->fb_base;
-
- pwidth = ((panel_info.vl_col+7) >> 3);
- for (y=0; y<panel_info.vl_row; y++) {
- i = y * pwidth;
- for (x=0; x<pwidth; x+=5) {
- serial_putc_raw_dev (PSOC_PSC, (p[i+x+2]<<4 & 0xF0) | (p[i+x+3]>>4 & 0x0F));
- serial_putc_raw_dev (PSOC_PSC, (p[i+x+3]<<4 & 0xF0) | (p[i+x+4]>>4 & 0x0F));
- serial_putc_raw_dev (PSOC_PSC, (p[i+x+4]<<4 & 0xF0) | (p[i+x]>>4 & 0x0F));
- serial_putc_raw_dev (PSOC_PSC, (p[i+x]<<4 & 0xF0) | (p[i+x+1]>>4 & 0x0F));
- serial_putc_raw_dev (PSOC_PSC, (p[i+x+1]<<4 & 0xF0) | (p[i+x+2]>>4 & 0x0F));
- }
- }
- }
-#endif
-
- /* 3 */
- serial_setrts_dev (PSOC_PSC, RTS_NEGATE);
- for (retries = PSOC_RETRIES; retries; retries--) {
- if (serial_getcts_dev(PSOC_PSC) == CTS_NEGATE)
- break;
- udelay (PSOC_WAIT_TIME);
- }
-
- return;
-}
-#ifdef CONFIG_PROGRESSBAR
-
-void show_progress (int size, int tot)
-{
- int cnt;
- int i;
- static int rc = 0;
-
- rc += size;
-
- cnt = ((LCD_WIDTH/FONT_WIDTH) * rc) / tot;
-
- rc -= (cnt * tot) / (LCD_WIDTH/FONT_WIDTH);
-
- for (i = 0; i < cnt; i++) {
- lcd_putc(0xdc);
- }
-
- if (cnt) {
- lcd_enable(); /* MCC200-specific - send the framebuffer to PSoC */
- }
-}
-
-#endif
-
-int bmp_display(ulong addr, int x, int y)
-{
- int ret;
- bmp_image_t *bmp = (bmp_image_t *)addr;
-
- if (!bmp) {
- printf("There is no valid bmp file at the given address\n");
- return 1;
- }
-
- ret = lcd_display_bitmap((ulong)bmp, x, y);
-
- if ((unsigned long)bmp != addr)
- free(bmp);
-
- return ret;
-}
-
-#endif /* CONFIG_LCD */
deleted file mode 100644
@@ -1,314 +0,0 @@
-/*
- * (C) Copyright 2003-2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <asm/processor.h>
-
-/* Two MT48LC8M32B2 for 32 MB */
-/* #include "mt48lc8m32b2-6-7.h" */
-
-/* One MT48LC16M32S2 for 64 MB */
-/* #include "mt48lc16m32s2-75.h" */
-#if defined (CONFIG_MCC200_SDRAM)
-#include "mt48lc16m16a2-75.h"
-#else
-#include "mt46v16m16-75.h"
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern flash_info_t flash_info[]; /* FLASH chips info */
-
-extern int do_auto_update(void);
-ulong flash_get_size (ulong base, int banknum);
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start (int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set mode register: extended mode */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-#endif
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-
- udelay(10);
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- * is something else than 0x00000000.
- */
-
-phys_size_t initdram (int board_type)
-{
- ulong dramsize = 0;
- ulong dramsize2 = 0;
- uint svr, pvr;
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set tap delay */
- *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-#endif
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20)) {
- dramsize = 0;
- }
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- }
-
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
-
- /* find RAM size using SDRAM CS1 only */
- if (!dramsize)
- sdram_start(0);
- test2 = test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- if (!dramsize) {
- sdram_start(1);
- test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
- }
- if (test1 > test2) {
- sdram_start(0);
- dramsize2 = test1;
- } else {
- dramsize2 = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize2 < (1 << 20)) {
- dramsize2 = 0;
- }
-
- /* set SDRAM CS1 size according to the amount of RAM found */
- if (dramsize2 > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
- | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
- }
-
-#else /* CONFIG_SYS_RAMBOOT */
-
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
- if (dramsize >= 0x13) {
- dramsize = (1 << (dramsize - 0x13)) << 20;
- } else {
- dramsize = 0;
- }
-
- /* retrieve size of memory connected to SDRAM CS1 */
- dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
- if (dramsize2 >= 0x13) {
- dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
- } else {
- dramsize2 = 0;
- }
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- /*
- * On MPC5200B we need to set the special configuration delay in the
- * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
- * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
- *
- * "The SDelay should be written to a value of 0x00000004. It is
- * required to account for changes caused by normal wafer processing
- * parameters."
- */
- svr = get_svr();
- pvr = get_pvr();
- if ((SVR_MJREV(svr) >= 2) && (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
- *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
- __asm__ volatile ("sync");
- }
-
- return dramsize + dramsize2;
-}
-
-int checkboard (void)
-{
-#if defined(CONFIG_PRS200)
- puts ("Board: PRS200\n");
-#else
- puts ("Board: MCC200\n");
-#endif
- return 0;
-}
-
-int misc_init_r (void)
-{
- ulong flash_sup_end, snum;
-
- /*
- * Adjust flash start and offset to detected values
- */
- gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
- gd->bd->bi_flashoffset = 0;
-
- /*
- * Check if boot FLASH isn't max size
- */
- if (gd->bd->bi_flashsize < (0 - CONFIG_SYS_FLASH_BASE)) {
- /* adjust mapping */
- *(vu_long *)MPC5XXX_BOOTCS_START = *(vu_long *)MPC5XXX_CS0_START =
- START_REG(gd->bd->bi_flashstart);
- *(vu_long *)MPC5XXX_BOOTCS_STOP = *(vu_long *)MPC5XXX_CS0_STOP =
- STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize);
-
- /*
- * Re-check to get correct base address
- */
- flash_get_size(gd->bd->bi_flashstart, CONFIG_SYS_MAX_FLASH_BANKS - 1);
-
- /*
- * Re-do flash protection upon new addresses
- */
- flash_protect (FLAG_PROTECT_CLEAR,
- gd->bd->bi_flashstart, 0xffffffff,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- /* Monitor protection ON by default */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- /* Environment protection ON by default */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- /* Redundant environment protection ON by default */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR_REDUND,
- CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
- }
-
- if (gd->bd->bi_flashsize > (32 << 20)) {
- /* Unprotect the upper bank of the Flash */
- *(volatile int*)MPC5XXX_CS0_CFG |= (1 << 6);
- flash_protect (FLAG_PROTECT_CLEAR,
- flash_info[0].start[0] + flash_info[0].size / 2,
- (flash_info[0].start[0] - 1) + flash_info[0].size,
- &flash_info[0]);
- *(volatile int*)MPC5XXX_CS0_CFG &= ~(1 << 6);
- printf ("Warning: Only 32 of 64 MB of Flash are accessible from U-Boot\n");
- flash_info[0].size = 32 << 20;
- for (snum = 0, flash_sup_end = gd->bd->bi_flashstart + (32<<20);
- flash_info[0].start[snum] < flash_sup_end;
- snum++);
- flash_info[0].sector_count = snum;
- }
-
-#ifdef CONFIG_AUTO_UPDATE
- do_auto_update();
-#endif
- return (0);
-}
-
-#ifdef CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
- debug ("init_ide_reset\n");
-
-}
-
-void ide_set_reset (int idereset)
-{
- debug ("ide_reset(%d)\n", idereset);
-
-}
-#endif
-
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
- doc_probe (CONFIG_SYS_DOC_BASE);
-}
-#endif
deleted file mode 100644
@@ -1,16 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x714f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
deleted file mode 100644
@@ -1,14 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 0 /* is SDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x00CD0000
-#define SDRAM_CONTROL 0x504F0000
-#define SDRAM_CONFIG1 0xD2322800
-#define SDRAM_CONFIG2 0x8AD70000
deleted file mode 100644
@@ -1,14 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 0 /* is SDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x00CD0000
-#define SDRAM_CONTROL 0x504F0000
-#define SDRAM_CONFIG1 0xD2322800
-#define SDRAM_CONFIG2 0x8AD70000
deleted file mode 100644
@@ -1,12 +0,0 @@
-/*
- * Configuration Registers for the MT48LC8M32B2 SDRAM on the MPC5200 platform
- */
-
-#define SDRAM_DDR 0 /* is SDR */
-
-/* Settings for XLB = 132 MHz */
-
-#define SDRAM_MODE 0x008d0000 /* CL-3 BURST-8 -> Mode Register MBAR + 0x0100 */
-#define SDRAM_CONTROL 0x504f0000 /* Control Register MBAR + 0x0104 */
-#define SDRAM_CONFIG1 0xc2222900 /* Delays between commands -> Configuration Register 1 MBAR + 0x0108 */
-#define SDRAM_CONFIG2 0x88c70000 /* Delays between commands -> Configuration Register 2 MBAR + 0x010C */
@@ -881,7 +881,7 @@ static void lcd_display_rle8_bitmap(bmp_image_t *bmp, ushort *cmap, uchar *fb,
}
#endif
-#if defined(CONFIG_MPC823) || defined(CONFIG_MCC200)
+#if defined(CONFIG_MPC823)
#define FB_PUT_BYTE(fb, from) *(fb)++ = (255 - *(from)++)
#else
#define FB_PUT_BYTE(fb, from) *(fb)++ = *(from)++
@@ -906,9 +906,7 @@ static inline void fb_put_word(uchar **fb, uchar **from)
int lcd_display_bitmap(ulong bmp_image, int x, int y)
{
-#if !defined(CONFIG_MCC200)
ushort *cmap = NULL;
-#endif
ushort *cmap_base = NULL;
ushort i, j;
uchar *fb;
@@ -956,8 +954,6 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y)
debug("Display-bmp: %d x %d with %d colors\n",
(int)width, (int)height, (int)colors);
-#if !defined(CONFIG_MCC200)
- /* MCC200 LCD doesn't need CMAP, supports 1bpp b&w only */
if (bmp_bpix == 8) {
cmap = configuration_get_cmap();
cmap_base = cmap;
@@ -985,24 +981,6 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y)
#endif
}
}
-#endif
- /*
- * BMP format for Monochrome assumes that the state of a
- * pixel is described on a per Bit basis, not per Byte.
- * So, in case of Monochrome BMP we should align widths
- * on a byte boundary and convert them from Bit to Byte
- * units.
- * Probably, PXA250 and MPC823 process 1bpp BMP images in
- * their own ways, so make the converting to be MCC200
- * specific.
- */
-#if defined(CONFIG_MCC200)
- if (bpix == 1) {
- width = ((width + 7) & ~7) >> 3;
- x = ((x + 7) & ~7) >> 3;
- pwidth= ((pwidth + 7) & ~7) >> 3;
- }
-#endif
padded_width = (width & 0x3 ? (width & ~0x3) + 4 : width);
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,SYS_TEXT_BASE=0xFFF00000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFFF00000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="PRS200"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="PRS200,MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="PRS200,SYS_TEXT_BASE=0xFFF00000"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
deleted file mode 100644
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="PRS200,SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM"
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MCC200=y
@@ -15,6 +15,8 @@ Board Arch CPU Commit Removed Last known m
TOP5200 powerpc mpc5200 - - Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
TOP860 powerpc mpc860 - - Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
TOP9000 arm at91sam9xeXXX - - Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
+PRS200 powerpc mpc5200 - 2014-11-05
+MCC200 powerpc mpc5200 - 2014-11-05
TQM8272 powerpc mpc8260 f06f9a1 2014-10-27 Wolfgang Denk <wd@denx.de>
TQM8260 powerpc mpc8260 ccc1950 2014-10-27 Wolfgang Denk <wd@denx.de>
IDS8247 powerpc mpc8260 6afb357 2014-10-27 Heiko Schocher <hs@denx.de>
deleted file mode 100644
@@ -1,397 +0,0 @@
-/*
- * (C) Copyright 2006-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200
-#define CONFIG_MCC200 1 /* MCC200 board */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFC000000 boot low (standard configuration)
- * 0xFFF00000 boot high
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- *
- * To select console on the one of 8 external UARTs,
- * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
- * or as 5, 6, 7, or 8 for the second Quad UART.
- * COM11, COM12, COM13, COM14 are located on the second Quad UART.
- *
- * CONFIG_PSC_CONSOLE must be undefined in this case.
- */
-#if !defined(CONFIG_PRS200)
-/* MCC200 configuration: */
-#ifdef CONFIG_CONSOLE_COM12
-#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */
-#else
-#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */
-#endif
-#else
-/* PRS200 configuration: */
-#undef CONFIG_QUART_CONSOLE
-#endif /* CONFIG_PRS200 */
-/*
- * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
- * and undefine CONFIG_QUART_CONSOLE.
- */
-#if !defined(CONFIG_PRS200)
-/* MCC200 configuration: */
-#define CONFIG_PSC_CONSOLE 1 /* PSC1 may be COM */
-#define CONFIG_PSC_CONSOLE2 2 /* PSC2 is PSoC */
-#else
-/* PRS200 configuration: */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#endif
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_MII 1
-
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-/* automatic software updates (see board/mcc200/auto_update.c) */
-#define CONFIG_AUTO_UPDATE 1
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_USB
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#ifdef CONFIG_PRS200
-# define CONFIG_SYS__BOARDNAME "prs200"
-# define CONFIG_SYS__LINUX_CONSOLE "ttyS0"
-#else
-# define CONFIG_SYS__BOARDNAME "mcc200"
-# define CONFIG_SYS__LINUX_CONSOLE "ttyEU5"
-#endif
-
-/* Network */
-#define CONFIG_ETHADDR 00:17:17:ff:00:00
-#define CONFIG_IPADDR 10.76.9.29
-#define CONFIG_SERVERIP 10.76.9.1
-
-#include <version.h> /* For U-Boot version */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ubootver=" U_BOOT_VERSION "\0" \
- "netdev=eth0\0" \
- "hostname=" CONFIG_SYS__BOARDNAME "\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/mtdblock2 " \
- "rootfstype=cramfs\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcons=setenv bootargs ${bootargs} " \
- "console=${console},${baudrate} " \
- "ubootver=${ubootver} board=${board}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addcons;bootm\0" \
- "console=" CONFIG_SYS__LINUX_CONSOLE "\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/" CONFIG_SYS__BOARDNAME "/uImage\0" \
- "load=tftp 200000 /tftpboot/" CONFIG_SYS__BOARDNAME "/u-boot.bin\0" \
- "text_base=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "kernel_addr=0xFC0C0000\0" \
- "update=protect off ${text_base} +${filesize};" \
- "era ${text_base} +${filesize};" \
- "cp.b 200000 ${text_base} ${filesize}\0" \
- "unlock=yes\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at 0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!)
- * 0xFE000000 for 32 MB
- * 0xFF000000 for 16 MB
- * 0xFF800000 for 8 MB
- */
-#define CONFIG_SYS_FLASH_BASE 0xfc000000
-#define CONFIG_SYS_FLASH_SIZE 0x04000000
-
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
-
-#if CONFIG_SYS_TEXT_BASE == CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LOWBOOT 1
-#endif
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xf0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-/* #define CONFIG_MPC5xxx_FEC 1 */
-/* #define CONFIG_MPC5xxx_FEC_MII100 */
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 1
-
-/*
- * LCD Splash Screen
- */
-#if !defined(CONFIG_PRS200)
-#define CONFIG_LCD 1
-#define CONFIG_PROGRESSBAR 1
-#endif
-
-#if defined(CONFIG_LCD)
-#define CONFIG_SPLASH_SCREEN 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-#define LCD_BPP LCD_MONOCHROME
-#endif
-
-/*
- * GPIO configuration
- */
-/* 0x10000004 = 32MB SDRAM */
-/* 0x90000004 = 64MB SDRAM */
-#if defined(CONFIG_LCD)
-/* set PSC2 in UART mode */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000044
-#else
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000004
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x0004fb00
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-/* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */
-#define CONFIG_SYS_CS2_START 0x80000000
-#define CONFIG_SYS_CS2_SIZE 0x00001000
-#define CONFIG_SYS_CS2_CFG 0x1d300
-
-/* Second Quad UART @0x80010000 */
-#define CONFIG_SYS_CS1_START 0x80010000
-#define CONFIG_SYS_CS1_SIZE 0x00001000
-#define CONFIG_SYS_CS1_CFG 0x1d300
-
-/* Leica - build revision resistors */
-/*
-#define CONFIG_SYS_CS3_START 0x80020000
-#define CONFIG_SYS_CS3_SIZE 0x00000004
-#define CONFIG_SYS_CS3_CFG 0x1d300
-*/
-
-/*
- * Select one of quarts as a default
- * console. If undefined - PSC console
- * wil be default
- */
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*
- * QUART Expanders support
- */
-#if defined(CONFIG_QUART_CONSOLE)
-/*
- * We'll use NS16550 chip routines,
- */
-#define CONFIG_SYS_NS16550 1
-#define CONFIG_SYS_NS16550_SERIAL 1
-#define CONFIG_CONS_INDEX 1
-/*
- * To achieve necessary offset on SC16C554
- * A0-A2 (register select) pins with NS16550
- * functions (in struct NS16550), REG_SIZE
- * should be 4, because A0-A2 pins are connected
- * to DA2-DA4 address bus lines.
- */
-#define CONFIG_SYS_NS16550_REG_SIZE 4
-/*
- * LocalPlus Bus already inited in cpu_init_f(),
- * so can work with QUART's chip selects.
- * One of four SC16C554 UARTs is selected with
- * A3-A4 (DA5-DA6) lines.
- */
-#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) && !defined(CONFIG_PRS200)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5)
-#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9)
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5)
-#else
-#error "Wrong QUART expander number."
-#endif
-
-/*
- * SC16C554 chip's external crystal oscillator frequency
- * is 7.3728 MHz
- */
-#define CONFIG_SYS_NS16550_CLK 7372800
-#endif /* CONFIG_QUART_CONSOLE */
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00005000
-
-#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */
-#define CONFIG_AUTOBOOT_STOP_STR "432"
-#define CONFIG_SILENT_CONSOLE 1
-
-#endif /* __CONFIG_H */
@@ -250,7 +250,7 @@ typedef struct vidinfo {
void *priv; /* Pointer to driver-specific data */
} vidinfo_t;
-#endif /* CONFIG_MPC823, CONFIG_CPU_PXA25X, CONFIG_MCC200, CONFIG_ATMEL_LCD */
+#endif /* CONFIG_MPC823, CONFIG_CPU_PXA25X, CONFIG_ATMEL_LCD */
extern vidinfo_t panel_info;
mcc200 and prs200 are old and have no maintainer. Remove the boards. This also removes the mcc200 specific 1bpp BMP support from common/lcd.c Cc: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> --- arch/powerpc/cpu/mpc5xxx/Kconfig | 4 - board/mcc200/Kconfig | 9 - board/mcc200/MAINTAINERS | 17 - board/mcc200/Makefile | 8 - board/mcc200/auto_update.c | 521 -------------------------- board/mcc200/lcd.c | 200 ---------- board/mcc200/mcc200.c | 314 ---------------- board/mcc200/mt46v16m16-75.h | 16 - board/mcc200/mt48lc16m16a2-75.h | 14 - board/mcc200/mt48lc16m32s2-75.h | 14 - board/mcc200/mt48lc8m32b2-6-7.h | 12 - common/lcd.c | 24 +- configs/mcc200_COM12_SDRAM_defconfig | 4 - configs/mcc200_COM12_defconfig | 4 - configs/mcc200_COM12_highboot_SDRAM_defconfig | 4 - configs/mcc200_COM12_highboot_defconfig | 4 - configs/mcc200_SDRAM_defconfig | 4 - configs/mcc200_defconfig | 3 - configs/mcc200_highboot_SDRAM_defconfig | 4 - configs/mcc200_highboot_defconfig | 4 - configs/prs200_DDR_defconfig | 4 - configs/prs200_defconfig | 4 - configs/prs200_highboot_DDR_defconfig | 4 - configs/prs200_highboot_defconfig | 4 - doc/README.scrapyard | 2 + include/configs/mcc200.h | 397 -------------------- include/lcd.h | 2 +- 27 files changed, 4 insertions(+), 1597 deletions(-) delete mode 100644 board/mcc200/Kconfig delete mode 100644 board/mcc200/MAINTAINERS delete mode 100644 board/mcc200/Makefile delete mode 100644 board/mcc200/auto_update.c delete mode 100644 board/mcc200/lcd.c delete mode 100644 board/mcc200/mcc200.c delete mode 100644 board/mcc200/mt46v16m16-75.h delete mode 100644 board/mcc200/mt48lc16m16a2-75.h delete mode 100644 board/mcc200/mt48lc16m32s2-75.h delete mode 100644 board/mcc200/mt48lc8m32b2-6-7.h delete mode 100644 configs/mcc200_COM12_SDRAM_defconfig delete mode 100644 configs/mcc200_COM12_defconfig delete mode 100644 configs/mcc200_COM12_highboot_SDRAM_defconfig delete mode 100644 configs/mcc200_COM12_highboot_defconfig delete mode 100644 configs/mcc200_SDRAM_defconfig delete mode 100644 configs/mcc200_defconfig delete mode 100644 configs/mcc200_highboot_SDRAM_defconfig delete mode 100644 configs/mcc200_highboot_defconfig delete mode 100644 configs/prs200_DDR_defconfig delete mode 100644 configs/prs200_defconfig delete mode 100644 configs/prs200_highboot_DDR_defconfig delete mode 100644 configs/prs200_highboot_defconfig delete mode 100644 include/configs/mcc200.h