diff mbox

[U-Boot,v3] mx53loco: Add support for SEIKO 4.3'' WVGA panel

Message ID 1357744216-27068-1-git-send-email-fabio.estevam@freescale.com
State Awaiting Upstream
Delegated to: Stefano Babic
Headers show

Commit Message

Fabio Estevam Jan. 9, 2013, 3:10 p.m. UTC 
Add support for the Seiko 4.3'' WVGA panel on mx53loco.

By default, the CLAA WVGA panel is selected.

In order to support the Seiko panel, the enviroment variable 'panel' must be
set to 'seiko'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v2:
- Simplify lcd detection logic
Changes since v1:
- Allow a single binary to support both CLAA and Seiko panels
 board/freescale/mx53loco/mx53loco.c       |    2 --
 board/freescale/mx53loco/mx53loco_video.c |   38 ++++++++++++++++++++++++++---
 2 files changed, 35 insertions(+), 5 deletions(-)

Comments

Stefano Babic Jan. 9, 2013, 6:24 p.m. UTC | #1 
On 09/01/2013 16:10, Fabio Estevam wrote:
> Add support for the Seiko 4.3'' WVGA panel on mx53loco.
> 
> By default, the CLAA WVGA panel is selected.
> 
> In order to support the Seiko panel, the enviroment variable 'panel' must be
> set to 'seiko'.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic
diff mbox

Patch

diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index 60cd4f0..8f39c38 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -503,8 +503,6 @@  int board_init(void)
 	mxc_set_sata_internal_clock();
 	setup_iomux_i2c();
 
-	lcd_enable();
-
 	return 0;
 }
 
diff --git a/board/freescale/mx53loco/mx53loco_video.c b/board/freescale/mx53loco/mx53loco_video.c
index 69991e8..a4d5a6a 100644
--- a/board/freescale/mx53loco/mx53loco_video.c
+++ b/board/freescale/mx53loco/mx53loco_video.c
@@ -46,6 +46,21 @@  static struct fb_videomode const claa_wvga = {
 	.vmode		= FB_VMODE_NONINTERLACED
 };
 
+static struct fb_videomode const seiko_wvga = {
+	.name		= "Seiko-43WVF1G",
+	.refresh	= 60,
+	.xres		= 800,
+	.yres		= 480,
+	.pixclock	= 29851, /* picosecond (33.5 MHz) */
+	.left_margin	= 89,
+	.right_margin	= 164,
+	.upper_margin	= 23,
+	.lower_margin	= 10,
+	.hsync_len	= 10,
+	.vsync_len	= 10,
+	.sync		= 0,
+};
+
 void setup_iomux_lcd(void)
 {
 	mxc_request_iomux(MX53_PIN_DI0_DISP_CLK, IOMUX_CONFIG_ALT0);
@@ -86,9 +101,26 @@  void setup_iomux_lcd(void)
 	gpio_direction_output(IOMUX_TO_GPIO(MX53_PIN_GPIO_1), 1);
 }
 
-void lcd_enable(void)
+int board_video_skip(void)
 {
-	int ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
+	int ret;
+	char const *e = getenv("panel");
+
+	if (e) {
+		if (strcmp(e, "seiko") == 0) {
+			ret = ipuv3_fb_init(&seiko_wvga, 0, IPU_PIX_FMT_RGB24);
+			if (ret)
+				printf("Seiko cannot be configured: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/*
+	 * 'panel' env variable not found or has different value than 'seiko'
+	 *  Defaulting to claa lcd.
+	 */
+	ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
 	if (ret)
-		printf("LCD cannot be configured: %d\n", ret);
+		printf("CLAA cannot be configured: %d\n", ret);
+	return ret;
 }