@@ -9,16 +9,20 @@ Subject: [PATCH] brcm63xx: setup pinctrl for internal switch leds on bcm6368
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -104,6 +104,15 @@ void __init board_early_setup(const stru
+@@ -104,6 +104,19 @@ void __init board_early_setup(const stru
GPIO_MODE_6348_G0_EXT_MII;
}
-+ if (BCMCPU_IS_6368() && board.has_enetsw) {
++ if ((BCMCPU_IS_6368() || (BCMCPU_IS_6318())) && board.has_enetsw) {
+ int i;
+
+ for (i = 0; i < 4; i++) {
-+ if (board.enetsw.used_ports[i].used)
-+ val |= (GPIO_MODE_6368_EPHY0_LED << i);
++ if (board.enetsw.used_ports[i].used) {
++ if (BCMCPU_IS_6368())
++ val |= (GPIO_MODE_6368_EPHY0_LED << i);
++ else if (BCMCPU_IS_6318())
++ val |= BIT(i+4);
++ }
+ }
+ }
+
@@ -8,7 +8,7 @@
+ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
}
- if (BCMCPU_IS_6368() && board.has_enetsw) {
+ if ((BCMCPU_IS_6368() || (BCMCPU_IS_6318())) && board.has_enetsw) {
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -651,6 +651,8 @@
@@ -18,7 +18,7 @@ Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data
#include "board_common.h"
-@@ -191,6 +192,7 @@ static struct of_device_id of_ids[] = {
+@@ -195,6 +196,7 @@ static struct of_device_id of_ids[] = {
int __init board_register_devices(void)
{
int usbh_ports = 0;
@@ -26,7 +26,7 @@ Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data
#if CONFIG_OF
if (of_have_populated_dt()) {
-@@ -271,6 +273,10 @@ int __init board_register_devices(void)
+@@ -275,6 +277,10 @@ int __init board_register_devices(void)
board.ephy_reset_gpio_flags);
}
@@ -11,7 +11,7 @@ Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -261,7 +261,7 @@ int __init board_register_devices(void)
+@@ -265,7 +265,7 @@ int __init board_register_devices(void)
if (board.num_spis)
spi_register_board_info(board.spis, board.num_spis);
@@ -39,7 +39,7 @@
return;
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -275,7 +275,8 @@ int __init board_register_devices(void)
+@@ -279,7 +279,8 @@ int __init board_register_devices(void)
/* register any fixups */
for (i = 0; i < board.has_caldata; i++)
@@ -1,6 +1,6 @@
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -276,7 +276,7 @@ int __init board_register_devices(void)
+@@ -280,7 +280,7 @@ int __init board_register_devices(void)
/* register any fixups */
for (i = 0; i < board.has_caldata; i++)
pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
@@ -36,7 +36,7 @@ Subject: [PATCH 72/72] 446-BCM63XX-add-a-fixup-for-rt2x00-devices
#include "board_common.h"
-@@ -274,9 +275,19 @@ int __init board_register_devices(void)
+@@ -278,9 +279,19 @@ int __init board_register_devices(void)
}
/* register any fixups */
Add BCM6318 to GPIO_MODE internal switch port leds setup. As with BCM6368 the pinmux for the switch LEDs in BCM6318 is also lost when LEDE initializes the peripherals. Fix it. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> --- ...rcm63xx-setup-pinctrl-for-internal-switch-leds-on-b.patch | 12 ++++++++---- .../patches-4.4/403-6358-enet1-external-mii-clk.patch | 2 +- ...13-BCM63XX-allow-providing-fixup-data-in-board-data.patch | 4 ++-- .../418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch | 2 +- .../patches-4.4/420-BCM63XX-add-endian-check-for-ath9k.patch | 2 +- .../patches-4.4/421-BCM63XX-add-led-pin-for-ath9k.patch | 2 +- .../422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch | 2 +- 7 files changed, 15 insertions(+), 11 deletions(-)