| Message ID | 1427814488-28467-3-git-send-email-alex.bennee@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Michael Ellerman |
| Headers | show |
On Tue, Mar 31, 2015 at 04:08:00PM +0100, Alex Bennée wrote: > Currently x86, powerpc and soon arm64 use the same two architecture > specific bits for guest debug support for software and hardware > breakpoints. This makes the shared values explicit while leaving the > gate open for another architecture to use some other value if they > really really want to. > > Signed-off-by: Alex Bennée <alex.bennee@linaro.org> > > diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h > index ab4d473..1731569 100644 > --- a/arch/powerpc/include/uapi/asm/kvm.h > +++ b/arch/powerpc/include/uapi/asm/kvm.h > @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { > * and upper 16 bits are architecture specific. Architecture specific defines > * that ioctl is for setting hardware breakpoint or software breakpoint. > */ > -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > > /* definition of registers in kvm_run */ > struct kvm_sync_regs { > diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h > index d7dcef5..1438202 100644 > --- a/arch/x86/include/uapi/asm/kvm.h > +++ b/arch/x86/include/uapi/asm/kvm.h > @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { > __u64 dr7; > }; > > -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > #define KVM_GUESTDBG_INJECT_DB 0x00040000 > #define KVM_GUESTDBG_INJECT_BP 0x00080000 > > diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h > index 5eedf84..ce2db14 100644 > --- a/include/uapi/linux/kvm.h > +++ b/include/uapi/linux/kvm.h > @@ -525,8 +525,16 @@ struct kvm_s390_irq { > > /* for KVM_SET_GUEST_DEBUG */ > > -#define KVM_GUESTDBG_ENABLE 0x00000001 > -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 > +#define KVM_GUESTDBG_ENABLE (1 << 0) > +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) > + > +/* > + * Architecture specific stuff uses the top 16 bits of the field, > + * however there is some shared commonality for the common cases > + */ > +#define __KVM_GUESTDBG_USE_SW_BP (1 << 16) > +#define __KVM_GUESTDBG_USE_HW_BP (1 << 17) > + > > struct kvm_guest_debug { > __u32 control; > -- > 2.3.4 > Reviewed-by: Andrew Jones <drjones@redhat.com>
On Tue, Mar 31, 2015 at 04:08:00PM +0100, Alex Bennée wrote: > Currently x86, powerpc and soon arm64 use the same two architecture > specific bits for guest debug support for software and hardware > breakpoints. This makes the shared values explicit while leaving the > gate open for another architecture to use some other value if they > really really want to. > > Signed-off-by: Alex Bennée <alex.bennee@linaro.org> > > diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h > index ab4d473..1731569 100644 > --- a/arch/powerpc/include/uapi/asm/kvm.h > +++ b/arch/powerpc/include/uapi/asm/kvm.h > @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { > * and upper 16 bits are architecture specific. Architecture specific defines > * that ioctl is for setting hardware breakpoint or software breakpoint. > */ > -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > > /* definition of registers in kvm_run */ > struct kvm_sync_regs { > diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h > index d7dcef5..1438202 100644 > --- a/arch/x86/include/uapi/asm/kvm.h > +++ b/arch/x86/include/uapi/asm/kvm.h > @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { > __u64 dr7; > }; > > -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > #define KVM_GUESTDBG_INJECT_DB 0x00040000 > #define KVM_GUESTDBG_INJECT_BP 0x00080000 > > diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h > index 5eedf84..ce2db14 100644 > --- a/include/uapi/linux/kvm.h > +++ b/include/uapi/linux/kvm.h > @@ -525,8 +525,16 @@ struct kvm_s390_irq { > > /* for KVM_SET_GUEST_DEBUG */ > > -#define KVM_GUESTDBG_ENABLE 0x00000001 > -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 > +#define KVM_GUESTDBG_ENABLE (1 << 0) > +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) > + > +/* > + * Architecture specific stuff uses the top 16 bits of the field, can you be more specific than 'stuff' here? features? > + * however there is some shared commonality for the common cases I don't like this sentence; shared commonality is a pleonasm and the use of however makes it sounds like there's some caveat here. If the top 16 bits are indeed arhictecture specific, then I think they should just be defined in their architecture specific headers. Unless the idea here is that there's a fixed set of of flags that architectures can choose to support, in which case it should simply be defined in the common header. > + */ > +#define __KVM_GUESTDBG_USE_SW_BP (1 << 16) > +#define __KVM_GUESTDBG_USE_HW_BP (1 << 17) > + > > struct kvm_guest_debug { > __u32 control; > -- > 2.3.4 >
Christoffer Dall <christoffer.dall@linaro.org> writes: > On Tue, Mar 31, 2015 at 04:08:00PM +0100, Alex Bennée wrote: >> Currently x86, powerpc and soon arm64 use the same two architecture >> specific bits for guest debug support for software and hardware >> breakpoints. This makes the shared values explicit while leaving the >> gate open for another architecture to use some other value if they >> really really want to. >> >> Signed-off-by: Alex Bennée <alex.bennee@linaro.org> >> >> diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h >> index ab4d473..1731569 100644 >> --- a/arch/powerpc/include/uapi/asm/kvm.h >> +++ b/arch/powerpc/include/uapi/asm/kvm.h >> @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { >> * and upper 16 bits are architecture specific. Architecture specific defines >> * that ioctl is for setting hardware breakpoint or software breakpoint. >> */ >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP >> >> /* definition of registers in kvm_run */ >> struct kvm_sync_regs { >> diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h >> index d7dcef5..1438202 100644 >> --- a/arch/x86/include/uapi/asm/kvm.h >> +++ b/arch/x86/include/uapi/asm/kvm.h >> @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { >> __u64 dr7; >> }; >> >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP >> #define KVM_GUESTDBG_INJECT_DB 0x00040000 >> #define KVM_GUESTDBG_INJECT_BP 0x00080000 >> >> diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h >> index 5eedf84..ce2db14 100644 >> --- a/include/uapi/linux/kvm.h >> +++ b/include/uapi/linux/kvm.h >> @@ -525,8 +525,16 @@ struct kvm_s390_irq { >> >> /* for KVM_SET_GUEST_DEBUG */ >> >> -#define KVM_GUESTDBG_ENABLE 0x00000001 >> -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 >> +#define KVM_GUESTDBG_ENABLE (1 << 0) >> +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) >> + >> +/* >> + * Architecture specific stuff uses the top 16 bits of the field, > > can you be more specific than 'stuff' here? features? > >> + * however there is some shared commonality for the common cases > > I don't like this sentence; shared commonality is a pleonasm and the use > of however makes it sounds like there's some caveat here. OK I can see that - after I looked it up ;-) > If the top 16 bits are indeed arhictecture specific, then I think they > should just be defined in their architecture specific headers. Unless > the idea here is that there's a fixed set of of flags that architectures > can choose to support, in which case it should simply be defined in the > common header. Well an architecture might not support some features and want to use those bits for something else? I didn't want to force the bottom two of the architecture specific bits to wasted if the features don't exist. > > >> + */ >> +#define __KVM_GUESTDBG_USE_SW_BP (1 << 16) >> +#define __KVM_GUESTDBG_USE_HW_BP (1 << 17) >> + >> >> struct kvm_guest_debug { >> __u32 control; >> -- >> 2.3.4 >>
On Mon, Apr 13, 2015 at 03:51:33PM +0100, Alex Bennée wrote: > > Christoffer Dall <christoffer.dall@linaro.org> writes: > > > On Tue, Mar 31, 2015 at 04:08:00PM +0100, Alex Bennée wrote: > >> Currently x86, powerpc and soon arm64 use the same two architecture > >> specific bits for guest debug support for software and hardware > >> breakpoints. This makes the shared values explicit while leaving the > >> gate open for another architecture to use some other value if they > >> really really want to. > >> > >> Signed-off-by: Alex Bennée <alex.bennee@linaro.org> > >> > >> diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h > >> index ab4d473..1731569 100644 > >> --- a/arch/powerpc/include/uapi/asm/kvm.h > >> +++ b/arch/powerpc/include/uapi/asm/kvm.h > >> @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { > >> * and upper 16 bits are architecture specific. Architecture specific defines > >> * that ioctl is for setting hardware breakpoint or software breakpoint. > >> */ > >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > >> > >> /* definition of registers in kvm_run */ > >> struct kvm_sync_regs { > >> diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h > >> index d7dcef5..1438202 100644 > >> --- a/arch/x86/include/uapi/asm/kvm.h > >> +++ b/arch/x86/include/uapi/asm/kvm.h > >> @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { > >> __u64 dr7; > >> }; > >> > >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > >> #define KVM_GUESTDBG_INJECT_DB 0x00040000 > >> #define KVM_GUESTDBG_INJECT_BP 0x00080000 > >> > >> diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h > >> index 5eedf84..ce2db14 100644 > >> --- a/include/uapi/linux/kvm.h > >> +++ b/include/uapi/linux/kvm.h > >> @@ -525,8 +525,16 @@ struct kvm_s390_irq { > >> > >> /* for KVM_SET_GUEST_DEBUG */ > >> > >> -#define KVM_GUESTDBG_ENABLE 0x00000001 > >> -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 > >> +#define KVM_GUESTDBG_ENABLE (1 << 0) > >> +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) > >> + > >> +/* > >> + * Architecture specific stuff uses the top 16 bits of the field, > > > > can you be more specific than 'stuff' here? features? > > > >> + * however there is some shared commonality for the common cases > > > > I don't like this sentence; shared commonality is a pleonasm and the use > > of however makes it sounds like there's some caveat here. > > OK I can see that - after I looked it up ;-) > > > If the top 16 bits are indeed arhictecture specific, then I think they > > should just be defined in their architecture specific headers. Unless > > the idea here is that there's a fixed set of of flags that architectures > > can choose to support, in which case it should simply be defined in the > > common header. > > Well an architecture might not support some features and want to use > those bits for something else? I didn't want to force the bottom two > of the architecture specific bits to wasted if the features don't exist. This change comes from a discussion we had on v1 of this series http://www.spinics.net/lists/kvm-arm/msg12409.html > > > > > > >> + */ > >> +#define __KVM_GUESTDBG_USE_SW_BP (1 << 16) > >> +#define __KVM_GUESTDBG_USE_HW_BP (1 << 17) > >> + > >> > >> struct kvm_guest_debug { > >> __u32 control; > >> -- > >> 2.3.4 > >> > > -- > Alex Bennée
On Mon, Apr 13, 2015 at 03:51:33PM +0100, Alex Bennée wrote: > > Christoffer Dall <christoffer.dall@linaro.org> writes: > > > On Tue, Mar 31, 2015 at 04:08:00PM +0100, Alex Bennée wrote: > >> Currently x86, powerpc and soon arm64 use the same two architecture > >> specific bits for guest debug support for software and hardware > >> breakpoints. This makes the shared values explicit while leaving the > >> gate open for another architecture to use some other value if they > >> really really want to. > >> > >> Signed-off-by: Alex Bennée <alex.bennee@linaro.org> > >> > >> diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h > >> index ab4d473..1731569 100644 > >> --- a/arch/powerpc/include/uapi/asm/kvm.h > >> +++ b/arch/powerpc/include/uapi/asm/kvm.h > >> @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { > >> * and upper 16 bits are architecture specific. Architecture specific defines > >> * that ioctl is for setting hardware breakpoint or software breakpoint. > >> */ > >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > >> > >> /* definition of registers in kvm_run */ > >> struct kvm_sync_regs { > >> diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h > >> index d7dcef5..1438202 100644 > >> --- a/arch/x86/include/uapi/asm/kvm.h > >> +++ b/arch/x86/include/uapi/asm/kvm.h > >> @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { > >> __u64 dr7; > >> }; > >> > >> -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 > >> -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 > >> +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP > >> +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP > >> #define KVM_GUESTDBG_INJECT_DB 0x00040000 > >> #define KVM_GUESTDBG_INJECT_BP 0x00080000 > >> > >> diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h > >> index 5eedf84..ce2db14 100644 > >> --- a/include/uapi/linux/kvm.h > >> +++ b/include/uapi/linux/kvm.h > >> @@ -525,8 +525,16 @@ struct kvm_s390_irq { > >> > >> /* for KVM_SET_GUEST_DEBUG */ > >> > >> -#define KVM_GUESTDBG_ENABLE 0x00000001 > >> -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 > >> +#define KVM_GUESTDBG_ENABLE (1 << 0) > >> +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) > >> + > >> +/* > >> + * Architecture specific stuff uses the top 16 bits of the field, > > > > can you be more specific than 'stuff' here? features? > > > >> + * however there is some shared commonality for the common cases > > > > I don't like this sentence; shared commonality is a pleonasm and the use > > of however makes it sounds like there's some caveat here. > > OK I can see that - after I looked it up ;-) > > > If the top 16 bits are indeed arhictecture specific, then I think they > > should just be defined in their architecture specific headers. Unless > > the idea here is that there's a fixed set of of flags that architectures > > can choose to support, in which case it should simply be defined in the > > common header. > > Well an architecture might not support some features and want to use > those bits for something else? I didn't want to force the bottom two > of the architecture specific bits to wasted if the features don't exist. > In that case I think the definition is local to each architecture and should indeed just be duplicated. The __ definitions complicate more than they help as they are exported to userspace etc. The KVM maintainers may have a different view on this though. -Christoffer
diff --git a/arch/powerpc/include/uapi/asm/kvm.h b/arch/powerpc/include/uapi/asm/kvm.h index ab4d473..1731569 100644 --- a/arch/powerpc/include/uapi/asm/kvm.h +++ b/arch/powerpc/include/uapi/asm/kvm.h @@ -310,8 +310,8 @@ struct kvm_guest_debug_arch { * and upper 16 bits are architecture specific. Architecture specific defines * that ioctl is for setting hardware breakpoint or software breakpoint. */ -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP /* definition of registers in kvm_run */ struct kvm_sync_regs { diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h index d7dcef5..1438202 100644 --- a/arch/x86/include/uapi/asm/kvm.h +++ b/arch/x86/include/uapi/asm/kvm.h @@ -250,8 +250,8 @@ struct kvm_debug_exit_arch { __u64 dr7; }; -#define KVM_GUESTDBG_USE_SW_BP 0x00010000 -#define KVM_GUESTDBG_USE_HW_BP 0x00020000 +#define KVM_GUESTDBG_USE_SW_BP __KVM_GUESTDBG_USE_SW_BP +#define KVM_GUESTDBG_USE_HW_BP __KVM_GUESTDBG_USE_HW_BP #define KVM_GUESTDBG_INJECT_DB 0x00040000 #define KVM_GUESTDBG_INJECT_BP 0x00080000 diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h index 5eedf84..ce2db14 100644 --- a/include/uapi/linux/kvm.h +++ b/include/uapi/linux/kvm.h @@ -525,8 +525,16 @@ struct kvm_s390_irq { /* for KVM_SET_GUEST_DEBUG */ -#define KVM_GUESTDBG_ENABLE 0x00000001 -#define KVM_GUESTDBG_SINGLESTEP 0x00000002 +#define KVM_GUESTDBG_ENABLE (1 << 0) +#define KVM_GUESTDBG_SINGLESTEP (1 << 1) + +/* + * Architecture specific stuff uses the top 16 bits of the field, + * however there is some shared commonality for the common cases + */ +#define __KVM_GUESTDBG_USE_SW_BP (1 << 16) +#define __KVM_GUESTDBG_USE_HW_BP (1 << 17) + struct kvm_guest_debug { __u32 control;
Currently x86, powerpc and soon arm64 use the same two architecture specific bits for guest debug support for software and hardware breakpoints. This makes the shared values explicit while leaving the gate open for another architecture to use some other value if they really really want to. Signed-off-by: Alex Bennée <alex.bennee@linaro.org>