@@ -149,6 +149,19 @@ config TARGET_MINI_X
bool "MINI_X"
depends on MACH_SUN4I
+config TARGET_MSI_PRIMO73
+ bool "MSI Primo73 (7\" tablet)"
+ depends on MACH_SUN7I
+ ---help---
+ The MSI Primo73 is an A20 based tablet, with 1G RAM, 16G NAND,
+ 1024x600 TN LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
+ rear camera, 3000 mAh battery, gt911 touchscreen, mma8452 accelerometer
+ and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
+ (both volume buttons are also connected to the UBOOT_SEL pin). The
+ external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
+ OTG and 3.5mm headphone jack. More details are available at
+ http://linux-sunxi.org/MSI_Primo73
+
config TARGET_MSI_PRIMO81
bool "MSI Primo81 (7.85\" tablet)"
depends on MACH_SUN6I
@@ -67,6 +67,11 @@ M: Chen-Yu Tsai <wens@csie.org>
S: Maintained
F: configs/Ippo_q8h_v5_defconfig
+MSI-PRIMO73 BOARD
+M: Siarhei Siamashka <siarhei.siamashka@gmail.com>
+S: Maintained
+F: configs/MSI_Primo73_defconfig
+
MSI-PRIMO81 BOARD
M: Siarhei Siamashka <siarhei.siamashka@gmail.com>
S: Maintained
@@ -31,6 +31,7 @@ obj-$(CONFIG_TARGET_MELE_A1000G) += dram_sun4i_360_1024_iow8.o
obj-$(CONFIG_TARGET_MELE_M3) += dram_sun7i_384_1024_iow16.o
obj-$(CONFIG_TARGET_MINI_X) += dram_sun4i_360_512.o
obj-$(CONFIG_TARGET_MINI_X_1GB) += dram_sun4i_360_1024_iow16.o
+obj-$(CONFIG_TARGET_MSI_PRIMO73) += dram_sun7i_384_1024_iow16.o
obj-$(CONFIG_TARGET_PCDUINO3) += dram_linksprite_pcduino3.o
obj-$(CONFIG_TARGET_QT840A) += dram_sun7i_384_512_busw16_iow16.o
obj-$(CONFIG_TARGET_R7DONGLE) += dram_r7dongle.o
new file mode 100644
@@ -0,0 +1,12 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
+CONFIG_FDTFILE="sun7i-a20-primo73.dtb"
+CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:60000,le:60,ri:160,up:13,lo:12,hs:100,vs:10,sync:0,vmode:0"
+CONFIG_VIDEO_LCD_POWER="PH8"
+CONFIG_VIDEO_LCD_BL_EN="PH7"
+CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_USB_KEYBOARD=n
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_SUNXI=y
++S:CONFIG_MACH_SUN7I=y
++S:CONFIG_TARGET_MSI_PRIMO73=y
This patch uses the same DRAM settings as in the pre-installed Android firmware. The LCD display is supported too. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> --- The LCD settings are only useful with the recent u-boot video patches from Hans de Goede, but do not cause any harm even without them. board/sunxi/Kconfig | 13 +++++++++++++ board/sunxi/MAINTAINERS | 5 +++++ board/sunxi/Makefile | 1 + configs/MSI_Primo73_defconfig | 12 ++++++++++++ 4 files changed, 31 insertions(+) create mode 100644 configs/MSI_Primo73_defconfig