Message ID | 20190417090349.47489-1-yinbo.zhu@nxp.com |
---|---|
State | Superseded |
Delegated to: | Joe Hershberger |
Headers | show |
Series | [U-Boot,v1] net: use block layer in net driver | expand |
On Wed, Apr 17, 2019 at 4:02 AM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > From: Yinbo Zhu <yinbo.zhu@nxp.com> > > At present the MMC subsystem maintains its own list > of MMC devices. This cannot work with driver model > when CONFIG_BLK is enabled, use blk_dread to > replace previous mmc read interface, > > Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> > --- > drivers/net/phy/cortina.c | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c > index a04a118f90..2337c3403c 100644 > --- a/drivers/net/phy/cortina.c > +++ b/drivers/net/phy/cortina.c > @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct phy_device *phydev) > printf("MMC read: dev # %u, block # %u, count %u ...\n", > dev, blk, cnt); > mmc_init(mmc); > - (void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt, > + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, > addr); Should this be switching on CONFIG_BLK or CONFIG_DM_MMC or something. > } > #endif > -- > 2.17.1 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > https://lists.denx.de/listinfo/u-boot
On Thu, May 9, 2019 at 3:02 PM Joe Hershberger <joe.hershberger@gmail.com> wrote: > > On Wed, Apr 17, 2019 at 4:02 AM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > From: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > At present the MMC subsystem maintains its own list > > of MMC devices. This cannot work with driver model > > when CONFIG_BLK is enabled, use blk_dread to > > replace previous mmc read interface, > > > > Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> > > --- > > drivers/net/phy/cortina.c | 2 +- > > 1 file changed, 1 insertion(+), 1 deletion(-) > > > > diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c > > index a04a118f90..2337c3403c 100644 > > --- a/drivers/net/phy/cortina.c > > +++ b/drivers/net/phy/cortina.c > > @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct phy_device *phydev) > > printf("MMC read: dev # %u, block # %u, count %u ...\n", > > dev, blk, cnt); > > mmc_init(mmc); > > - (void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt, > > + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, > > addr); > > Should this be switching on CONFIG_BLK or CONFIG_DM_MMC or something. Any word? > > > } > > #endif > > -- > > 2.17.1 > > > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > https://lists.denx.de/listinfo/u-boot
> -----Original Message----- > From: Joe Hershberger [mailto:joe.hershberger@gmail.com] > Sent: 2019年6月1日 19:16 > To: Yinbo Zhu <yinbo.zhu@nxp.com> > Cc: York Sun <york.sun@nxp.com>; u-boot@lists.denx.de; Xiaobo Xie > <xiaobo.xie@nxp.com>; Jiafei Pan <jiafei.pan@nxp.com>; Ran Wang > <ran.wang_1@nxp.com> > Subject: [EXT] Re: [U-Boot] [PATCH v1] net: use block layer in net driver > > Caution: EXT Email > > On Thu, May 9, 2019 at 3:02 PM Joe Hershberger <joe.hershberger@gmail.com> > wrote: > > > > On Wed, Apr 17, 2019 at 4:02 AM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > > > From: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > > > At present the MMC subsystem maintains its own list of MMC devices. > > > This cannot work with driver model when CONFIG_BLK is enabled, use > > > blk_dread to replace previous mmc read interface, > > > > > > Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> > > > --- > > > drivers/net/phy/cortina.c | 2 +- > > > 1 file changed, 1 insertion(+), 1 deletion(-) > > > > > > diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c > > > index a04a118f90..2337c3403c 100644 > > > --- a/drivers/net/phy/cortina.c > > > +++ b/drivers/net/phy/cortina.c > > > @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct phy_device > *phydev) > > > printf("MMC read: dev # %u, block # %u, count %u ...\n", > > > dev, blk, cnt); > > > mmc_init(mmc); > > > - (void)mmc->block_dev.block_read(&mmc->block_dev, blk, > cnt, > > > + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, > > > addr); > > > > Should this be switching on CONFIG_BLK or CONFIG_DM_MMC or something. > > Any word? > Yes, need enable above two config. And default uboot had enabled them. Regards, Yinbo > > > > > } > > > #endif > > > -- > > > 2.17.1 > > > > > > _______________________________________________ > > > U-Boot mailing list > > > U-Boot@lists.denx.de > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fli > > > > sts.denx.de%2Flistinfo%2Fu-boot&data=02%7C01%7Cyinbo.zhu%40nxp.c > > > > om%7Cf4dd39cb85174bb474e208d6e682980b%7C686ea1d3bc2b4c6fa92cd9 > 9c5c30 > > > > 1635%7C0%7C1%7C636949845952441371&sdata=PJGcNYuSLsAndJaGTBe > khmEN > > > sad96LwmV92jLec5mrs%3D&reserved=0
On Sun, Jun 2, 2019 at 9:28 PM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > > -----Original Message----- > > From: Joe Hershberger [mailto:joe.hershberger@gmail.com] > > Sent: 2019年6月1日 19:16 > > To: Yinbo Zhu <yinbo.zhu@nxp.com> > > Cc: York Sun <york.sun@nxp.com>; u-boot@lists.denx.de; Xiaobo Xie > > <xiaobo.xie@nxp.com>; Jiafei Pan <jiafei.pan@nxp.com>; Ran Wang > > <ran.wang_1@nxp.com> > > Subject: [EXT] Re: [U-Boot] [PATCH v1] net: use block layer in net driver > > > > Caution: EXT Email > > > > On Thu, May 9, 2019 at 3:02 PM Joe Hershberger <joe.hershberger@gmail.com> > > wrote: > > > > > > On Wed, Apr 17, 2019 at 4:02 AM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > > > > > From: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > > > > > At present the MMC subsystem maintains its own list of MMC devices. > > > > This cannot work with driver model when CONFIG_BLK is enabled, use > > > > blk_dread to replace previous mmc read interface, > > > > > > > > Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > --- > > > > drivers/net/phy/cortina.c | 2 +- > > > > 1 file changed, 1 insertion(+), 1 deletion(-) > > > > > > > > diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c > > > > index a04a118f90..2337c3403c 100644 > > > > --- a/drivers/net/phy/cortina.c > > > > +++ b/drivers/net/phy/cortina.c > > > > @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct phy_device > > *phydev) > > > > printf("MMC read: dev # %u, block # %u, count %u ...\n", > > > > dev, blk, cnt); > > > > mmc_init(mmc); > > > > - (void)mmc->block_dev.block_read(&mmc->block_dev, blk, > > cnt, > > > > + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, > > > > addr); > > > > > > Should this be switching on CONFIG_BLK or CONFIG_DM_MMC or something. > > > > Any word? > > > Yes, need enable above two config. And default uboot had enabled them. OK, if this depends on them, even if they are default, this block should check for the option in v2. Also, if there is still a use-case for the "mmc->block_dev.block_read" that exists with different or fewer options, then that could also be a config option instead of replaced. Thanks, -Joe > > Regards, > Yinbo > > > > > > > } > > > > #endif > > > > -- > > > > 2.17.1 > > > > > > > > _______________________________________________ > > > > U-Boot mailing list > > > > U-Boot@lists.denx.de > > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fli > > > > > > sts.denx.de%2Flistinfo%2Fu-boot&data=02%7C01%7Cyinbo.zhu%40nxp.c > > > > > > om%7Cf4dd39cb85174bb474e208d6e682980b%7C686ea1d3bc2b4c6fa92cd9 > > 9c5c30 > > > > > > 1635%7C0%7C1%7C636949845952441371&sdata=PJGcNYuSLsAndJaGTBe > > khmEN > > > > sad96LwmV92jLec5mrs%3D&reserved=0
> -----Original Message----- > From: Joe Hershberger [mailto:joe.hershberger@gmail.com] > Sent: 2019年6月10日 23:41 > To: Yinbo Zhu <yinbo.zhu@nxp.com> > Cc: York Sun <york.sun@nxp.com>; u-boot@lists.denx.de; Xiaobo Xie > <xiaobo.xie@nxp.com>; Jiafei Pan <jiafei.pan@nxp.com>; Ran Wang > <ran.wang_1@nxp.com>; Y.b. Lu <yangbo.lu@nxp.com> > Subject: Re: [EXT] Re: [U-Boot] [PATCH v1] net: use block layer in net driver > > Caution: EXT Email > > On Sun, Jun 2, 2019 at 9:28 PM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > > > > > > -----Original Message----- > > > From: Joe Hershberger [mailto:joe.hershberger@gmail.com] > > > Sent: 2019年6月1日 19:16 > > > To: Yinbo Zhu <yinbo.zhu@nxp.com> > > > Cc: York Sun <york.sun@nxp.com>; u-boot@lists.denx.de; Xiaobo Xie > > > <xiaobo.xie@nxp.com>; Jiafei Pan <jiafei.pan@nxp.com>; Ran Wang > > > <ran.wang_1@nxp.com> > > > Subject: [EXT] Re: [U-Boot] [PATCH v1] net: use block layer in net > > > driver > > > > > > Caution: EXT Email > > > > > > On Thu, May 9, 2019 at 3:02 PM Joe Hershberger > > > <joe.hershberger@gmail.com> > > > wrote: > > > > > > > > On Wed, Apr 17, 2019 at 4:02 AM Yinbo Zhu <yinbo.zhu@nxp.com> wrote: > > > > > > > > > > From: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > > > > > > > At present the MMC subsystem maintains its own list of MMC devices. > > > > > This cannot work with driver model when CONFIG_BLK is enabled, > > > > > use blk_dread to replace previous mmc read interface, > > > > > > > > > > Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> > > > > > --- > > > > > drivers/net/phy/cortina.c | 2 +- > > > > > 1 file changed, 1 insertion(+), 1 deletion(-) > > > > > > > > > > diff --git a/drivers/net/phy/cortina.c > > > > > b/drivers/net/phy/cortina.c index a04a118f90..2337c3403c 100644 > > > > > --- a/drivers/net/phy/cortina.c > > > > > +++ b/drivers/net/phy/cortina.c > > > > > @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct > > > > > phy_device > > > *phydev) > > > > > printf("MMC read: dev # %u, block # %u, > count %u ...\n", > > > > > dev, blk, cnt); > > > > > mmc_init(mmc); > > > > > - (void)mmc->block_dev.block_read(&mmc->block_dev, > blk, > > > cnt, > > > > > + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, > > > > > addr); > > > > > > > > Should this be switching on CONFIG_BLK or CONFIG_DM_MMC or > something. > > > > > > Any word? > > > > > Yes, need enable above two config. And default uboot had enabled them. > > OK, if this depends on them, even if they are default, this block should check for > the option in v2. Also, if there is still a use-case for the > "mmc->block_dev.block_read" that exists with different or fewer options, then > that could also be a config option instead of replaced. > > Thanks, > -Joe Hi joe, In fact, above change is only depend on BLK config, I have mistake about previous word, and I will apply your advice send v3 patch to upstream. Yinbo > > > > > Regards, > > Yinbo > > > > > > > > > } > > > > > #endif > > > > > -- > > > > > 2.17.1 > > > > > > > > > > _______________________________________________ > > > > > U-Boot mailing list > > > > > U-Boot@lists.denx.de > > > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F% > > > > > 2Fli > > > > > > > > > sts.denx.de%2Flistinfo%2Fu-boot&data=02%7C01%7Cyinbo.zhu%40nxp.c > > > > > > > > > om%7Cf4dd39cb85174bb474e208d6e682980b%7C686ea1d3bc2b4c6fa92cd9 > > > 9c5c30 > > > > > > > > > 1635%7C0%7C1%7C636949845952441371&sdata=PJGcNYuSLsAndJaGTBe > > > khmEN > > > > > sad96LwmV92jLec5mrs%3D&reserved=0
diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c index a04a118f90..2337c3403c 100644 --- a/drivers/net/phy/cortina.c +++ b/drivers/net/phy/cortina.c @@ -176,7 +176,7 @@ void cs4340_upload_firmware(struct phy_device *phydev) printf("MMC read: dev # %u, block # %u, count %u ...\n", dev, blk, cnt); mmc_init(mmc); - (void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt, + (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, addr); } #endif