new file mode 100644
@@ -0,0 +1,100 @@
+/*
+ * Copyright 2004-2008 Freescale Semiconductor, Inc.
+ * Copyright 2009 Semihalf.
+ *
+ * Approved as OSADL project by a majority of OSADL members and funded
+ * by OSADL membership fees in 2009; for details see www.osadl.org.
+ *
+ * Based on original driver from Freescale Semiconductor
+ * written by John Rigby <jrigby@freescale.com> on basis
+ * of drivers/mtd/nand/mxc_nand.c. Reworked and extended by
+ * Piotr Ziecik <kosmo@semihalf.com>.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef MPC5121_NFC_H
+#define MPC5121_NFC_H
+
+/* Addresses for NFC MAIN RAM BUFFER areas */
+#define NFC_MAIN_AREA(n) ((n) * 0x200)
+
+/* Addresses for NFC SPARE BUFFER areas */
+#define NFC_SPARE_BUFFERS 8
+#define NFC_SPARE_LEN 0x40
+#define NFC_SPARE_AREA(n) (0x1000 + ((n) * NFC_SPARE_LEN))
+
+/* MPC5121 NFC registers */
+#define NFC_BUF_ADDR 0x1E04
+#define NFC_FLASH_ADDR 0x1E06
+#define NFC_FLASH_CMD 0x1E08
+#define NFC_CONFIG 0x1E0A
+#define NFC_ECC_STATUS1 0x1E0C
+#define NFC_ECC_STATUS2 0x1E0E
+#define NFC_SPAS 0x1E10
+#define NFC_WRPROT 0x1E12
+#define NFC_NF_WRPRST 0x1E18
+#define NFC_CONFIG1 0x1E1A
+#define NFC_CONFIG2 0x1E1C
+#define NFC_UNLOCKSTART_BLK0 0x1E20
+#define NFC_UNLOCKEND_BLK0 0x1E22
+#define NFC_UNLOCKSTART_BLK1 0x1E24
+#define NFC_UNLOCKEND_BLK1 0x1E26
+#define NFC_UNLOCKSTART_BLK2 0x1E28
+#define NFC_UNLOCKEND_BLK2 0x1E2A
+#define NFC_UNLOCKSTART_BLK3 0x1E2C
+#define NFC_UNLOCKEND_BLK3 0x1E2E
+
+/* Bit Definitions: NFC_BUF_ADDR */
+#define NFC_RBA_MASK (7 << 0)
+#define NFC_ACTIVE_CS_SHIFT 5
+#define NFC_ACTIVE_CS_MASK (3 << NFC_ACTIVE_CS_SHIFT)
+
+/* Bit Definitions: NFC_CONFIG */
+#define NFC_BLS_UNLOCKED (1 << 1)
+
+/* Bit Definitions: NFC_CONFIG1 */
+#define NFC_ECC_4BIT (1 << 0)
+#define NFC_FULL_PAGE_DMA (1 << 1)
+#define NFC_SPARE_ONLY (1 << 2)
+#define NFC_ECC_ENABLE (1 << 3)
+#define NFC_INT_MASK (1 << 4)
+#define NFC_BIG_ENDIAN (1 << 5)
+#define NFC_RESET (1 << 6)
+#define NFC_CE (1 << 7)
+#define NFC_ONE_CYCLE (1 << 8)
+#define NFC_PPB_32 (0 << 9)
+#define NFC_PPB_64 (1 << 9)
+#define NFC_PPB_128 (2 << 9)
+#define NFC_PPB_256 (3 << 9)
+#define NFC_PPB_MASK (3 << 9)
+#define NFC_FULL_PAGE_INT (1 << 11)
+
+/* Bit Definitions: NFC_CONFIG2 */
+#define NFC_COMMAND (1 << 0)
+#define NFC_ADDRESS (1 << 1)
+#define NFC_INPUT (1 << 2)
+#define NFC_OUTPUT (1 << 3)
+#define NFC_ID (1 << 4)
+#define NFC_STATUS (1 << 5)
+#define NFC_CMD_FAIL (1 << 15)
+#define NFC_INT (1 << 15)
+
+/* Bit Definitions: NFC_WRPROT */
+#define NFC_WPC_LOCK_TIGHT (1 << 0)
+#define NFC_WPC_LOCK (1 << 1)
+#define NFC_WPC_UNLOCK (1 << 2)
+
+#endif /* MPC5121_NFC_H */
@@ -71,6 +71,7 @@ void __init mpc512x_init_IRQ(void)
static struct of_device_id __initdata of_bus_ids[] = {
{ .compatible = "fsl,mpc5121-immr", },
{ .compatible = "fsl,mpc5121-localbus", },
+ { .compatible = "fsl,mpc5121-nfc", },
{},
};
@@ -413,6 +413,13 @@ config MTD_NAND_FSL_UPM
Enables support for NAND Flash chips wired onto Freescale PowerPC
processor localbus with User-Programmable Machine support.
+config MTD_NAND_MPC5121_NFC
+ tristate "MPC5121 built-in NAND Flash Controller support"
+ depends on PPC_MPC512x
+ help
+ This enables the driver for the NAND flash controller on the
+ MPC5121 SoC.
+
config MTD_NAND_MXC
tristate "MXC NAND support"
depends on ARCH_MX2 || ARCH_MX3
@@ -39,5 +39,6 @@ obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o
obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o
obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
+obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
nand-objs := nand_base.o nand_bbt.o
new file mode 100644
@@ -0,0 +1,855 @@
+/*
+ * Copyright 2004-2008 Freescale Semiconductor, Inc.
+ * Copyright 2009 Semihalf.
+ *
+ * Based on original driver from Freescale Semiconductor
+ * written by John Rigby <jrigby@freescale.com> on basis
+ * of drivers/mtd/nand/mxc_nand.c. Reworked and extended
+ * Piotr Ziecik <kosmo@semihalf.com>.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+
+#include <asm/mpc512x.h>
+#include <asm/mpc5121_nfc.h>
+
+#define DRV_NAME "mpc5121_nfc"
+#define DRV_VERSION "0.5"
+
+/* Timeouts */
+#define NFC_RESET_TIMEOUT 1000 /* 1 ms */
+#define NFC_TIMEOUT (HZ / 10) /* 1/10 s */
+
+struct mpc5121_nfc_prv {
+ struct mtd_info mtd;
+ struct nand_chip chip;
+ int irq;
+ void __iomem *regs;
+ struct clk *clk;
+ wait_queue_head_t irq_waitq;
+ uint column;
+ int spareonly;
+ void __iomem *csreg;
+};
+
+static void mpc5121_nfc_done(struct mtd_info *mtd);
+
+#ifdef CONFIG_MTD_PARTITIONS
+static const char *mpc5121_nfc_pprobes[] = { "cmdlinepart", NULL };
+#endif
+
+/* Read NFC register */
+static inline u16 nfc_read(struct mtd_info *mtd, uint reg)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ return in_be16(prv->regs + reg);
+}
+
+/* Write NFC register */
+static inline void nfc_write(struct mtd_info *mtd, uint reg, u16 val)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ out_be16(prv->regs + reg, val);
+}
+
+/* Set bits in NFC register */
+static inline void nfc_set(struct mtd_info *mtd, uint reg, u16 bits)
+{
+ nfc_write(mtd, reg, nfc_read(mtd, reg) | bits);
+}
+
+/* Clear bits in NFC register */
+static inline void nfc_clear(struct mtd_info *mtd, uint reg, u16 bits)
+{
+ nfc_write(mtd, reg, nfc_read(mtd, reg) & ~bits);
+}
+
+/* Invoke address cycle */
+static inline void mpc5121_nfc_send_addr(struct mtd_info *mtd, u16 addr)
+{
+ nfc_write(mtd, NFC_FLASH_ADDR, addr);
+ nfc_write(mtd, NFC_CONFIG2, NFC_ADDRESS);
+ mpc5121_nfc_done(mtd);
+}
+
+/* Invoke command cycle */
+static inline void mpc5121_nfc_send_cmd(struct mtd_info *mtd, u16 cmd)
+{
+ nfc_write(mtd, NFC_FLASH_CMD, cmd);
+ nfc_write(mtd, NFC_CONFIG2, NFC_COMMAND);
+ mpc5121_nfc_done(mtd);
+}
+
+/* Send data from NFC buffers to NAND flash */
+static inline void mpc5121_nfc_send_prog_page(struct mtd_info *mtd)
+{
+ nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK);
+ nfc_write(mtd, NFC_CONFIG2, NFC_INPUT);
+ mpc5121_nfc_done(mtd);
+}
+
+/* Receive data from NAND flash */
+static inline void mpc5121_nfc_send_read_page(struct mtd_info *mtd)
+{
+ nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK);
+ nfc_write(mtd, NFC_CONFIG2, NFC_OUTPUT);
+ mpc5121_nfc_done(mtd);
+}
+
+/* Receive ID from NAND flash */
+static inline void mpc5121_nfc_send_read_id(struct mtd_info *mtd)
+{
+ nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK);
+ nfc_write(mtd, NFC_CONFIG2, NFC_ID);
+ mpc5121_nfc_done(mtd);
+}
+
+/* Receive status from NAND flash */
+static inline void mpc5121_nfc_send_read_status(struct mtd_info *mtd)
+{
+ nfc_clear(mtd, NFC_BUF_ADDR, NFC_RBA_MASK);
+ nfc_write(mtd, NFC_CONFIG2, NFC_STATUS);
+ mpc5121_nfc_done(mtd);
+}
+
+/* NFC interrupt handler */
+static irqreturn_t mpc5121_nfc_irq(int irq, void *data)
+{
+ struct mtd_info *mtd = data;
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ nfc_set(mtd, NFC_CONFIG1, NFC_INT_MASK);
+ wake_up(&prv->irq_waitq);
+
+ return IRQ_HANDLED;
+}
+
+/* Wait for operation complete */
+static void mpc5121_nfc_done(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+ int rv;
+
+ if ((nfc_read(mtd, NFC_CONFIG2) & NFC_INT) == 0) {
+ nfc_clear(mtd, NFC_CONFIG1, NFC_INT_MASK);
+ rv = wait_event_timeout(prv->irq_waitq,
+ (nfc_read(mtd, NFC_CONFIG2) & NFC_INT), NFC_TIMEOUT);
+
+ if (!rv)
+ printk(KERN_WARNING DRV_NAME
+ ": Timeout while waiting for interrupt.\n");
+ }
+
+ nfc_clear(mtd, NFC_CONFIG2, NFC_INT);
+}
+
+/* Do address cycle(s) */
+static void mpc5121_nfc_addr_cycle(struct mtd_info *mtd, int column, int page)
+{
+ struct nand_chip *chip = mtd->priv;
+ u32 pagemask = chip->pagemask;
+
+ if (column != -1) {
+ mpc5121_nfc_send_addr(mtd, column);
+ if (mtd->writesize > 512)
+ mpc5121_nfc_send_addr(mtd, column >> 8);
+ }
+
+ if (page != -1) {
+ do {
+ mpc5121_nfc_send_addr(mtd, page & 0xFF);
+ page >>= 8;
+ pagemask >>= 8;
+ } while (pagemask);
+ }
+}
+
+/* Control chip select signals */
+static void mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip)
+{
+ if (chip < 0) {
+ nfc_clear(mtd, NFC_CONFIG1, NFC_CE);
+ return;
+ }
+
+ nfc_clear(mtd, NFC_BUF_ADDR, NFC_ACTIVE_CS_MASK);
+ nfc_set(mtd, NFC_BUF_ADDR, (chip << NFC_ACTIVE_CS_SHIFT) &
+ NFC_ACTIVE_CS_MASK);
+ nfc_set(mtd, NFC_CONFIG1, NFC_CE);
+}
+
+/* Init external chip select logic on ADS5121 board */
+static int ads5121_chipselect_init(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+ struct device_node *dn;
+
+ dn = of_find_compatible_node(NULL, NULL, "fsl,mpc5121ads-cpld");
+ if (dn) {
+ prv->csreg = of_iomap(dn, 0);
+ of_node_put(dn);
+ if (!prv->csreg)
+ return -ENOMEM;
+
+ /* CPLD Register 9 controls NAND /CE Lines */
+ prv->csreg += 9;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+/* Control chips select signal on ADS5121 board */
+static void ads5121_select_chip(struct mtd_info *mtd, int chip)
+{
+ struct nand_chip *nand = mtd->priv;
+ struct mpc5121_nfc_prv *prv = nand->priv;
+ u8 v;
+
+ v = in_8(prv->csreg);
+ v |= 0x0F;
+
+ if (chip >= 0) {
+ mpc5121_nfc_select_chip(mtd, 0);
+ v &= ~(1 << chip);
+ } else
+ mpc5121_nfc_select_chip(mtd, -1);
+
+ out_8(prv->csreg, v);
+}
+
+/* Read NAND Ready/Busy signal */
+static int mpc5121_nfc_dev_ready(struct mtd_info *mtd)
+{
+ /*
+ * NFC handles ready/busy signal internally. Therefore, this function
+ * always returns status as ready.
+ */
+ return 1;
+}
+
+/* Write command to NAND flash */
+static void mpc5121_nfc_command(struct mtd_info *mtd, unsigned command,
+ int column, int page)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ prv->column = (column >= 0) ? column : 0;
+ prv->spareonly = 0;
+
+ switch (command) {
+ case NAND_CMD_PAGEPROG:
+ mpc5121_nfc_send_prog_page(mtd);
+ break;
+ /*
+ * NFC does not support sub-page reads and writes,
+ * so emulate them using full page transfers.
+ */
+ case NAND_CMD_READ0:
+ column = 0;
+ break;
+
+ case NAND_CMD_READ1:
+ prv->column += 256;
+ command = NAND_CMD_READ0;
+ column = 0;
+ break;
+
+ case NAND_CMD_READOOB:
+ prv->spareonly = 1;
+ command = NAND_CMD_READ0;
+ column = 0;
+ break;
+
+ case NAND_CMD_SEQIN:
+ mpc5121_nfc_command(mtd, NAND_CMD_READ0, column, page);
+ column = 0;
+ break;
+
+ case NAND_CMD_ERASE1:
+ case NAND_CMD_ERASE2:
+ case NAND_CMD_READID:
+ case NAND_CMD_STATUS:
+ break;
+
+ default:
+ return;
+ }
+
+ mpc5121_nfc_send_cmd(mtd, command);
+ mpc5121_nfc_addr_cycle(mtd, column, page);
+
+ switch (command) {
+ case NAND_CMD_READ0:
+ if (mtd->writesize > 512)
+ mpc5121_nfc_send_cmd(mtd, NAND_CMD_READSTART);
+ mpc5121_nfc_send_read_page(mtd);
+ break;
+
+ case NAND_CMD_READID:
+ mpc5121_nfc_send_read_id(mtd);
+ break;
+
+ case NAND_CMD_STATUS:
+ mpc5121_nfc_send_read_status(mtd);
+ if (chip->options & NAND_BUSWIDTH_16)
+ prv->column = 1;
+ else
+ prv->column = 0;
+ break;
+ }
+}
+
+/* Copy data from/to NFC spare buffers. */
+static void mpc5121_nfc_copy_spare(struct mtd_info *mtd, uint offset,
+ u8 *buffer, uint size, int wr)
+{
+ struct nand_chip *nand = mtd->priv;
+ struct mpc5121_nfc_prv *prv = nand->priv;
+ uint o, s, sbsize, blksize;
+
+ /*
+ * NAND spare area is available through NFC spare buffers.
+ * The NFC divides spare area into (page_size / 512) chunks.
+ * Each chunk is placed into separate spare memory area, using
+ * first (spare_size / num_of_chunks) bytes of the buffer.
+ *
+ * For NAND device in which the spare area is not divided fully
+ * by the number of chunks, number of used bytes in each spare
+ * buffer is rounded down to the nearest even number of bytes,
+ * and all remaining bytes are added to the last used spare area.
+ *
+ * For more information read section 26.6.10 of MPC5121e
+ * Microcontroller Reference Manual, Rev. 3.
+ */
+
+ /* Calculate number of valid bytes in each spare buffer */
+ sbsize = (mtd->oobsize / (mtd->writesize / 512)) & ~1;
+
+ while (size) {
+ /* Calculate spare buffer number */
+ s = offset / sbsize;
+ if (s > NFC_SPARE_BUFFERS - 1)
+ s = NFC_SPARE_BUFFERS - 1;
+
+ /*
+ * Calculate offset to requested data block in selected spare
+ * buffer and its size.
+ */
+ o = offset - (s * sbsize);
+ blksize = min(sbsize - o, size);
+
+ if (wr)
+ memcpy_toio(prv->regs + NFC_SPARE_AREA(s) + o,
+ buffer, blksize);
+ else
+ memcpy_fromio(buffer,
+ prv->regs + NFC_SPARE_AREA(s) + o, blksize);
+
+ buffer += blksize;
+ offset += blksize;
+ size -= blksize;
+ };
+}
+
+/* Copy data from/to NFC main and spare buffers */
+static void mpc5121_nfc_buf_copy(struct mtd_info *mtd, u_char *buf, int len,
+ int wr)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+ uint c = prv->column;
+ uint l;
+
+ /* Handle spare area access */
+ if (prv->spareonly || c >= mtd->writesize) {
+ /* Calculate offset from beginning of spare area */
+ if (c >= mtd->writesize)
+ c -= mtd->writesize;
+
+ prv->column += len;
+ mpc5121_nfc_copy_spare(mtd, c, buf, len, wr);
+ return;
+ }
+
+ /*
+ * Handle main area access - limit copy length to prevent
+ * crossing main/spare boundary.
+ */
+ l = min((uint)len, mtd->writesize - c);
+ prv->column += l;
+
+ if (wr)
+ memcpy_toio(prv->regs + NFC_MAIN_AREA(0) + c, buf, l);
+ else
+ memcpy_fromio(buf, prv->regs + NFC_MAIN_AREA(0) + c, l);
+
+ /* Handle crossing main/spare boundary */
+ if (l != len) {
+ buf += l;
+ len -= l;
+ mpc5121_nfc_buf_copy(mtd, buf, len, wr);
+ }
+}
+
+/* Read data from NFC buffers */
+static void mpc5121_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len)
+{
+ mpc5121_nfc_buf_copy(mtd, buf, len, 0);
+}
+
+/* Write data to NFC buffers */
+static void mpc5121_nfc_write_buf(struct mtd_info *mtd,
+ const u_char *buf, int len)
+{
+ mpc5121_nfc_buf_copy(mtd, (u_char *)buf, len, 1);
+}
+
+/* Compare buffer with NAND flash */
+static int mpc5121_nfc_verify_buf(struct mtd_info *mtd,
+ const u_char *buf, int len)
+{
+ u_char tmp[256];
+ uint bsize;
+
+ while (len) {
+ bsize = min(len, 256);
+ mpc5121_nfc_read_buf(mtd, tmp, bsize);
+
+ if (memcmp(buf, tmp, bsize))
+ return 1;
+
+ buf += bsize;
+ len -= bsize;
+ }
+
+ return 0;
+}
+
+/* Read byte from NFC buffers */
+static u8 mpc5121_nfc_read_byte(struct mtd_info *mtd)
+{
+ u8 tmp;
+
+ mpc5121_nfc_read_buf(mtd, &tmp, sizeof(tmp));
+
+ return tmp;
+}
+
+/* Read word from NFC buffers */
+static u16 mpc5121_nfc_read_word(struct mtd_info *mtd)
+{
+ u16 tmp;
+
+ mpc5121_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp));
+
+ return tmp;
+}
+
+/*
+ * Read NFC configuration from Reset Config Word
+ *
+ * NFC is configured during reset in basis of information stored
+ * in Reset Config Word. There is no other way to set NAND block
+ * size, spare size and bus width.
+ */
+static int mpc5121_nfc_read_hw_config(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc512x_reset_module *rm;
+ struct device_node *rmnode;
+ uint rcw_pagesize = 0;
+ uint rcw_sparesize = 0;
+ uint rcw_width;
+ uint rcwh;
+ uint romloc, ps;
+
+ rmnode = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-reset");
+ if (!rmnode) {
+ printk(KERN_ERR DRV_NAME ": Missing 'fsl,mpc5121-reset' "
+ "node in device tree!\n");
+ return -ENODEV;
+ }
+
+ rm = of_iomap(rmnode, 0);
+ if (!rm) {
+ printk(KERN_ERR DRV_NAME
+ ": Error mapping reset module node!\n");
+ return -EBUSY;
+ }
+
+ rcwh = in_be32(&rm->rcwhr);
+
+ /* Bit 6: NFC bus width */
+ rcw_width = ((rcwh >> 6) & 0x1) ? 2 : 1;
+
+ /* Bit 7: NFC Page/Spare size */
+ ps = (rcwh >> 7) & 0x1;
+
+ /* Bits [22:21]: ROM Location */
+ romloc = (rcwh >> 21) & 0x3;
+
+ /* Decode RCW bits */
+ switch ((ps << 2) | romloc) {
+ case 0x00:
+ case 0x01:
+ rcw_pagesize = 512;
+ rcw_sparesize = 16;
+ break;
+ case 0x02:
+ case 0x03:
+ rcw_pagesize = 4096;
+ rcw_sparesize = 128;
+ break;
+ case 0x04:
+ case 0x05:
+ rcw_pagesize = 2048;
+ rcw_sparesize = 64;
+ break;
+ case 0x06:
+ case 0x07:
+ rcw_pagesize = 4096;
+ rcw_sparesize = 218;
+ break;
+ }
+
+ mtd->writesize = rcw_pagesize;
+ mtd->oobsize = rcw_sparesize;
+ if (rcw_width == 2)
+ chip->options |= NAND_BUSWIDTH_16;
+
+ printk(KERN_NOTICE DRV_NAME ": Configured for "
+ "%u-bit NAND, page size %u "
+ "with %u spare.\n",
+ rcw_width * 8, rcw_pagesize,
+ rcw_sparesize);
+ iounmap(rm);
+ of_node_put(rmnode);
+ return 0;
+}
+
+/* Free driver resources */
+static void mpc5121_nfc_free(struct device *dev, struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ if (prv->clk) {
+ clk_disable(prv->clk);
+ clk_put(prv->clk);
+ }
+
+ if (prv->csreg)
+ iounmap(prv->csreg);
+}
+
+static int __init mpc5121_nfc_probe(struct of_device *op,
+ const struct of_device_id *match)
+{
+ struct device_node *rootnode, *dn = op->node;
+ struct device *dev = &op->dev;
+ struct mpc5121_nfc_prv *prv;
+ struct resource res;
+ struct mtd_info *mtd;
+#ifdef CONFIG_MTD_PARTITIONS
+ struct mtd_partition *parts;
+#endif
+ struct nand_chip *chip;
+ unsigned long regs_paddr, regs_size;
+ const uint *chips_no;
+ int resettime = 0;
+ int retval = 0;
+ int rev, len;
+
+ /*
+ * Check SoC revision. This driver supports only NFC
+ * in MPC5121 revision 2.
+ */
+ rev = (mfspr(SPRN_SVR) >> 4) & 0xF;
+ if (rev != 2) {
+ printk(KERN_ERR DRV_NAME
+ ": SoC revision %u is not supported!\n", rev);
+ return -ENXIO;
+ }
+
+ prv = devm_kzalloc(dev, sizeof(*prv), GFP_KERNEL);
+ if (!prv) {
+ printk(KERN_ERR DRV_NAME ": Memory exhausted!\n");
+ return -ENOMEM;
+ }
+
+ mtd = &prv->mtd;
+ chip = &prv->chip;
+
+ mtd->priv = chip;
+ chip->priv = prv;
+
+ /* Read NFC configuration from Reset Config Word */
+ retval = mpc5121_nfc_read_hw_config(mtd);
+ if (retval) {
+ printk(KERN_ERR DRV_NAME ": Unable to read NFC config!\n");
+ return retval;
+ }
+
+ prv->irq = irq_of_parse_and_map(dn, 0);
+ if (prv->irq == NO_IRQ) {
+ printk(KERN_ERR DRV_NAME ": Error mapping IRQ!\n");
+ return -EINVAL;
+ }
+
+ retval = of_address_to_resource(dn, 0, &res);
+ if (retval) {
+ printk(KERN_ERR DRV_NAME ": Error parsing memory region!\n");
+ return retval;
+ }
+
+ chips_no = of_get_property(dn, "chips", &len);
+ if (!chips_no || len != sizeof(*chips_no)) {
+ printk(KERN_ERR DRV_NAME ": Invalid/missing 'chips' "
+ "property!\n");
+ return -EINVAL;
+ }
+
+ regs_paddr = res.start;
+ regs_size = res.end - res.start + 1;
+
+ if (!devm_request_mem_region(dev, regs_paddr, regs_size, DRV_NAME)) {
+ printk(KERN_ERR DRV_NAME ": Error requesting memory region!\n");
+ return -EBUSY;
+ }
+
+ prv->regs = devm_ioremap(dev, regs_paddr, regs_size);
+ if (!prv->regs) {
+ printk(KERN_ERR DRV_NAME ": Error mapping memory region!\n");
+ return -ENOMEM;
+ }
+
+ mtd->name = "MPC5121 NAND";
+ chip->dev_ready = mpc5121_nfc_dev_ready;
+ chip->cmdfunc = mpc5121_nfc_command;
+ chip->read_byte = mpc5121_nfc_read_byte;
+ chip->read_word = mpc5121_nfc_read_word;
+ chip->read_buf = mpc5121_nfc_read_buf;
+ chip->write_buf = mpc5121_nfc_write_buf;
+ chip->verify_buf = mpc5121_nfc_verify_buf;
+ chip->select_chip = mpc5121_nfc_select_chip;
+ chip->options = NAND_NO_AUTOINCR | NAND_USE_FLASH_BBT;
+ chip->ecc.mode = NAND_ECC_SOFT;
+
+ /* Support external chip-select logic on ADS5121 board */
+ rootnode = of_find_node_by_path("/");
+ if (of_device_is_compatible(rootnode, "fsl,mpc5121ads")) {
+ retval = ads5121_chipselect_init(mtd);
+ if (retval) {
+ printk(KERN_ERR DRV_NAME ": Chipselect init error!\n");
+ of_node_put(rootnode);
+ return retval;
+ }
+
+ chip->select_chip = ads5121_select_chip;
+ }
+ of_node_put(rootnode);
+
+ /* Enable NFC clock */
+ prv->clk = clk_get(dev, "nfc_clk");
+ if (!prv->clk) {
+ printk(KERN_ERR DRV_NAME ": Unable to acquire NFC clock!\n");
+ retval = -ENODEV;
+ goto error;
+ }
+
+ clk_enable(prv->clk);
+
+ /* Reset NAND Flash controller */
+ nfc_set(mtd, NFC_CONFIG1, NFC_RESET);
+ while (nfc_read(mtd, NFC_CONFIG1) & NFC_RESET) {
+ if (resettime++ >= NFC_RESET_TIMEOUT) {
+ printk(KERN_ERR DRV_NAME
+ ": Timeout while resetting NFC!\n");
+ retval = -EINVAL;
+ goto error;
+ }
+
+ udelay(1);
+ }
+
+ /* Enable write to NFC memory */
+ nfc_write(mtd, NFC_CONFIG, NFC_BLS_UNLOCKED);
+
+ /* Enable write to all NAND pages */
+ nfc_write(mtd, NFC_UNLOCKSTART_BLK0, 0x0000);
+ nfc_write(mtd, NFC_UNLOCKEND_BLK0, 0xFFFF);
+ nfc_write(mtd, NFC_WRPROT, NFC_WPC_UNLOCK);
+
+ /*
+ * Setup NFC:
+ * - Big Endian transfers,
+ * - Interrupt after full page read/write.
+ */
+ nfc_write(mtd, NFC_CONFIG1, NFC_BIG_ENDIAN | NFC_INT_MASK |
+ NFC_FULL_PAGE_INT);
+
+ /* Set spare area size */
+ nfc_write(mtd, NFC_SPAS, mtd->oobsize >> 1);
+
+ init_waitqueue_head(&prv->irq_waitq);
+ retval = devm_request_irq(dev, prv->irq, &mpc5121_nfc_irq, 0, DRV_NAME,
+ mtd);
+ if (retval) {
+ printk(KERN_ERR DRV_NAME ": Error requesting IRQ!\n");
+ goto error;
+ }
+
+ /* Detect NAND chips */
+ if (nand_scan(mtd, *chips_no)) {
+ printk(KERN_ERR DRV_NAME ": NAND Flash not found !\n");
+ devm_free_irq(dev, prv->irq, mtd);
+ retval = -ENXIO;
+ goto error;
+ }
+
+ /* Set erase block size */
+ switch (mtd->erasesize / mtd->writesize) {
+ case 32:
+ nfc_set(mtd, NFC_CONFIG1, NFC_PPB_32);
+ break;
+
+ case 64:
+ nfc_set(mtd, NFC_CONFIG1, NFC_PPB_64);
+ break;
+
+ case 128:
+ nfc_set(mtd, NFC_CONFIG1, NFC_PPB_128);
+ break;
+
+ case 256:
+ nfc_set(mtd, NFC_CONFIG1, NFC_PPB_256);
+ break;
+
+ default:
+ printk(KERN_ERR DRV_NAME ": Unsupported NAND flash!\n");
+ devm_free_irq(dev, prv->irq, mtd);
+ retval = -ENXIO;
+ goto error;
+ }
+
+ dev_set_drvdata(dev, mtd);
+
+ /* Register device in MTD */
+#ifdef CONFIG_MTD_PARTITIONS
+ retval = parse_mtd_partitions(mtd, mpc5121_nfc_pprobes, &parts, 0);
+#ifdef CONFIG_MTD_OF_PARTS
+ if (retval == 0)
+ retval = of_mtd_parse_partitions(dev, dn, &parts);
+#endif
+ if (retval < 0) {
+ printk(KERN_ERR DRV_NAME ": Error parsing MTD partitions!\n");
+ devm_free_irq(dev, prv->irq, mtd);
+ retval = -EINVAL;
+ goto error;
+ }
+
+ if (retval > 0)
+ retval = add_mtd_partitions(mtd, parts, retval);
+ else
+#endif
+ retval = add_mtd_device(mtd);
+
+ if (retval) {
+ printk(KERN_ERR DRV_NAME ": Error adding MTD device!\n");
+ devm_free_irq(dev, prv->irq, mtd);
+ goto error;
+ }
+
+ return 0;
+error:
+ mpc5121_nfc_free(dev, mtd);
+ return retval;
+}
+
+static int __exit mpc5121_nfc_remove(struct of_device *op)
+{
+ struct device *dev = &op->dev;
+ struct mtd_info *mtd = dev_get_drvdata(dev);
+ struct nand_chip *chip = mtd->priv;
+ struct mpc5121_nfc_prv *prv = chip->priv;
+
+ nand_release(mtd);
+ devm_free_irq(dev, prv->irq, mtd);
+ mpc5121_nfc_free(dev, mtd);
+
+ return 0;
+}
+
+static struct of_device_id mpc5121_nfc_match[] = {
+ { .compatible = "fsl,mpc5121-nfc", },
+ {},
+};
+
+static struct of_platform_driver mpc5121_nfc_driver = {
+ .owner = THIS_MODULE,
+ .name = DRV_NAME,
+ .match_table = mpc5121_nfc_match,
+ .probe = mpc5121_nfc_probe,
+ .remove = __exit_p(mpc5121_nfc_remove),
+ .suspend = NULL,
+ .resume = NULL,
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init mpc5121_nfc_init(void)
+{
+ if (of_register_platform_driver(&mpc5121_nfc_driver) != 0) {
+ printk(KERN_ERR DRV_NAME ": Driver register failed!\n");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+static void __exit mpc5121_nfc_cleanup(void)
+{
+ of_unregister_platform_driver(&mpc5121_nfc_driver);
+}
+
+module_init(mpc5121_nfc_init);
+module_exit(mpc5121_nfc_cleanup);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc.");
+MODULE_DESCRIPTION("MPC5121 NAND MTD driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);