new file mode 100644
@@ -0,0 +1,104 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/hwmon/adi,ltc2947.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2947 high precision power and energy monitor
+
+maintainers:
+ - Nuno Sá <nuno.sa@analog.com>
+
+description: |
+ Analog Devices LTC2947 high precision power and energy monitor over SPI or I2C.
+
+ https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
+
+properties:
+ compatible:
+ enum:
+ - adi,ltc2947
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ description:
+ The LTC2947 uses either a trimmed internal oscillator or an external clock
+ as the time base for determining the integration period to represent time,
+ charge and energy. When an external clock is used, this property must be
+ set accordingly.
+ maxItems: 1
+
+ adi,accumulator-ctl-pol:
+ description:
+ This property controls the polarity of current that is accumulated to
+ calculate charge and energy so that, they can be only accumulated for
+ positive current for example. Since there are two sets of registers for
+ the accumulated values, this entry can also have two items which sets
+ energy1/charge1 and energy2/charger2 respectively. Check table 12 of the
+ datasheet for more information on the supported options.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - minItems: 2
+ maxItems: 2
+ items:
+ enum: [0, 1, 2, 3]
+ default: 0
+
+ adi,accumulation-deadband-microamp:
+ description:
+ This property controls the Accumulation Dead band which allows to set the
+ level of current below which no accumulation takes place.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ default: 0
+
+ adi,gpio-out-pol:
+ description:
+ This property controls the GPIO polarity. Setting it to one makes the GPIO
+ active high, setting it to zero makets it active low. When this property
+ is present, the GPIO is automatically configured as output and set to
+ control a fan as a function of measured temperature.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+ default: 0
+
+ adi,gpio-in-accum:
+ description:
+ When set, this property sets the GPIO as input. It is then used to control
+ the accumulation of charge, energy and time. This function can be
+ enabled/configured separately for each of the two sets of accumulation
+ registers. Check table 13 of the datasheet for more information on the
+ supported options. This property cannot be used together with
+ adi,gpio-out-pol.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - minItems: 2
+ maxItems: 2
+ items:
+ enum: [0, 1, 2]
+ default: 0
+
+required:
+ - compatible
+ - reg
+
+
+examples:
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ltc2947_spi: ltc2947@0 {
+ compatible = "adi,ltc2947";
+ reg = <0>;
+ /* accumulation takes place always for energ1/charge1. */
+ /* accumulation only on positive current for energy2/charge2. */
+ adi,accumulator-ctl-pol = <0 1>;
+ };
+ };
+...
@@ -9637,6 +9637,7 @@ F: drivers/hwmon/ltc2947-core.c
F: drivers/hwmon/ltc2947-spi.c
F: drivers/hwmon/ltc2947-i2c.c
F: drivers/hwmon/ltc2947.h
+F: Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
LTC4306 I2C MULTIPLEXER DRIVER
M: Michael Hennerich <michael.hennerich@analog.com>
Document the LTC2947 device devicetree bindings. Signed-off-by: Nuno Sá <nuno.sa@analog.com> --- Changes in v2: * Add license identifier; * Fix the uint32-array properties; * Set maximum at the same indent as allOf in adi,accumulation-deadband-microamp; * Set enum at the same indent as allOf in adi,gpio-out-pol; * Use spi instead of spi0 on the example; .../bindings/hwmon/adi,ltc2947.yaml | 104 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 105 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml