@@ -3,6 +3,7 @@
/dts-v1/;
#include "sun50i-h5.dtsi"
+#include "sun50i-h5-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
@@ -70,7 +70,7 @@
leds {
compatible = "gpio-leds";
- status {
+ led-0 {
label = "chip-pro:white:status";
gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
@@ -70,7 +70,7 @@
leds {
compatible = "gpio-leds";
- status {
+ led-0 {
label = "chip:white:status";
gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
@@ -67,7 +67,7 @@
leds {
compatible = "gpio-leds";
- status {
+ led-0 {
label = "sina31s:status:usr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
};
@@ -278,6 +278,7 @@
dphy: d-phy@1ca1000 {
compatible = "allwinner,sun6i-a31-mipi-dphy";
reg = <0x01ca1000 0x1000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_MIPI_DSI>,
<&ccu CLK_DSI_DPHY>;
clock-names = "bus", "mod";
@@ -105,6 +105,21 @@
/* enables internal regulator and de-asserts reset */
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
};
+
+ /*
+ * Power supply for the SATA disk, behind a USB-SATA bridge.
+ * Since it is a USB device, there is no consumer in the DT, so we
+ * have to keep this always on.
+ */
+ regulator-sata-disk-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "sata-disk-pwr";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+ };
};
&cpu0 {
@@ -57,7 +57,7 @@
ethernet1 = &sdiowifi;
};
- cec-gpio {
+ cec {
compatible = "cec-gpio";
cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
hdmi-phandle = <&hdmi>;
@@ -57,7 +57,7 @@
regulator-ramp-delay = <50>; /* 4ms */
enable-active-high;
- enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
gpios-states = <0x1>;
states = <1100000 0>, <1300000 1>;
@@ -6,6 +6,8 @@
/dts-v1/;
#include "suniv-f1c100s.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Lichee Pi Nano";
compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
@@ -50,8 +52,22 @@
};
};
+&otg_sram {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pe_pins>;
status = "okay";
};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; /* PE2 */
+ status = "okay";
+};
@@ -133,6 +133,32 @@
#size-cells = <0>;
};
+ usb_otg: usb@1c13000 {
+ compatible = "allwinner,suniv-f1c100s-musb";
+ reg = <0x01c13000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <26>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ allwinner,sram = <&otg_sram 1>;
+ status = "disabled";
+ };
+
+ usbphy: phy@1c13400 {
+ compatible = "allwinner,suniv-f1c100s-usb-phy";
+ reg = <0x01c13400 0x10>;
+ reg-names = "phy_ctrl";
+ clocks = <&ccu CLK_USB_PHY0>;
+ clock-names = "usb0_phy";
+ resets = <&ccu RST_USB_PHY0>;
+ reset-names = "usb0_reset";
+ #phy-cells = <1>;
+ status = "disabled";
+ };
+
ccu: clock@1c20000 {
compatible = "allwinner,suniv-f1c100s-ccu";
reg = <0x01c20000 0x400>;
@@ -181,6 +207,12 @@
pins = "PE0", "PE1";
function = "uart0";
};
+
+ /omit-if-no-ref/
+ uart1_pa_pins: uart1-pa-pins {
+ pins = "PA2", "PA3";
+ function = "uart1";
+ };
};
i2c0: i2c@1c27000 {
new file mode 100644
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Arm Ltd,
+ * based on work:
+ * Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Lctech Pi F1C200s";
+ compatible = "lctech,pi-f1c200s", "allwinner,suniv-f1c200s",
+ "allwinner,suniv-f1c100s";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_vcc3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&mmc0 {
+ broken-cd;
+ bus-width = <4>;
+ disable-wp;
+ vmmc-supply = <®_vcc3v3>;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pc_pins>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pa_pins>;
+ status = "okay";
+};
+
+/*
+ * This is a Type-C socket, but CC1/2 are not connected, and VBUS is connected
+ * to Vin, which supplies the board. Host mode works (if the board is powered
+ * otherwise), but peripheral is probably the intention.
+ */
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Popcorn Computer PopStick v1.1";
+ compatible = "sourceparts,popstick-v1.1", "sourceparts,popstick",
+ "allwinner,suniv-f1c200s", "allwinner,suniv-f1c100s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 4 6 GPIO_ACTIVE_HIGH>; /* PE6 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_vcc3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&mmc0 {
+ cd-gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
+ bus-width = <4>;
+ disable-wp;
+ vmmc-supply = <®_vcc3v3>;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pc_pins>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pe_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
Sync the devicetree files from the sunxi Linux queue [1], to match the Linux 6.4-rc pull request. Those patches are in Linux-next for a bit now. This is covering both 64-bit and 32-bit Allwinner SoCs with Arm Ltd. cores, we skip the new RISC-V bits for now, as sunxi RISC-V support for U-Boot is still work in progress. Among smaller cosmetic changes, this adds a SATA regulator node which we need in U-Boot to get rid of hard-coded GPIOs. Also this updates the Allwinner F1C100s DTs, adding its USB nodes, and also adding the DTs for two new boards. As before, this omits the non-backwards compatible changes to the R_INTC controller, to remain compatible with older kernels. [1] https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux.git/commit/?h=sunxi/dt-for-6.4&id=20c5db6c3d79d357c9d787edad3bbf03d98a08bf Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 1 + arch/arm/dts/sun5i-gr8-chip-pro.dts | 2 +- arch/arm/dts/sun5i-r8-chip.dts | 2 +- arch/arm/dts/sun6i-a31s-sina31s.dts | 2 +- arch/arm/dts/sun8i-a33.dtsi | 1 + arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 15 ++++ arch/arm/dts/sun8i-h3-beelink-x2.dts | 2 +- arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 2 +- arch/arm/dts/suniv-f1c100s-licheepi-nano.dts | 16 ++++ arch/arm/dts/suniv-f1c100s.dtsi | 32 ++++++++ arch/arm/dts/suniv-f1c200s-lctech-pi.dts | 76 ++++++++++++++++++ arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts | 81 ++++++++++++++++++++ 12 files changed, 227 insertions(+), 5 deletions(-) create mode 100644 arch/arm/dts/suniv-f1c200s-lctech-pi.dts create mode 100644 arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts