@@ -129,7 +129,7 @@
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
- flash: m25p80@0 {
+ flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25vf016b", "jedec,spi-nor";
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Header providing constants for i.MX28 pinctrl bindings.
*
* Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_MX28_PINCTRL_H__
@@ -1,143 +1,99 @@
-// SPDX-License-Identifier: GPL-2.0+
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
- * Copyright 2019
+ * Copyright 2021
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+ or X11
- *
*/
/dts-v1/;
-
-#include "imx28.dtsi"
+#include "imx28-lwe.dtsi"
/ {
- model = "Liebherr (LWE) XEA i.MX28 Board";
- compatible = "lwe,xea", "fsl,imx28";
-
- aliases {
- spi3 = &ssp3;
- };
-
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x10000000>;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_fec_3v3: regulator-fec-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "fec-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
-
- reg_usb_5v: regulator-usb-5v {
- compatible = "regulator-fixed";
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ compatible = "lwn,imx28-xea", "fsl,imx28";
};
-&mac0 {
- phy-mode = "rmii";
+&can0 {
pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-supply = <®_fec_3v3>;
- phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <1>;
- phy-reset-post-delay = <1>;
+ pinctrl-0 = <&can1_pins_a>;
status = "okay";
-
- fixed-link {
- speed = <100>;
- full-duplex;
- };
};
-&ssp0 {
- compatible = "fsl,imx28-mmc";
+&i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a>;
- bus-width = <8>;
- vmmc-supply = <®_3p3v>;
- non-removable;
+ pinctrl-0 = <&i2c1_pins_b>;
status = "okay";
};
-&ssp3 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
+&pinctrl {
pinctrl-names = "default";
- pinctrl-0 = <&spi3_pins_b>;
- status = "okay";
- spi-max-frequency = <40000000>;
- num-cs = <2>;
+ pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
- flash0: s25fl256s@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- spi-max-frequency = <40000000>;
+ hog_pins_a: hog@0 {
reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D02__GPIO_0_2
+ MX28_PAD_GPMI_D05__GPIO_0_5
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY0__GPIO_0_20
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_GPMI_RDY2__GPIO_0_22
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_CLE__GPIO_0_27
+ MX28_PAD_LCD_VSYNC__GPIO_1_28
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP2_SS1__GPIO_2_20
+ MX28_PAD_SSP2_SS2__GPIO_2_21
+ MX28_PAD_LCD_D00__GPIO_1_0
+ MX28_PAD_LCD_D01__GPIO_1_1
+ MX28_PAD_LCD_D02__GPIO_1_2
+ MX28_PAD_LCD_D03__GPIO_1_3
+ MX28_PAD_LCD_D04__GPIO_1_4
+ MX28_PAD_LCD_D05__GPIO_1_5
+ MX28_PAD_LCD_D06__GPIO_1_6
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ hog_pins_tiva: hog@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDY3__GPIO_0_23
+ MX28_PAD_GPMI_WRN__GPIO_0_25
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
- partition@0 {
- label = "SPL";
- reg = <0x0 0x10000>;
- read-only;
- };
- partition@10000 {
- label = "u-boot";
- reg = <0x10000 0x70000>;
- read-only;
- };
- partition@80000 {
- label = "uboot-env1";
- reg = <0x80000 0x10000>;
- };
- partition@90000 {
- label = "uboot-env2";
- reg = <0x90000 0x10000>;
- };
- partition@A0000 {
- label = "rescue";
- reg = <0xA0000 0xF40000>;
- };
- partition@FE0000 {
- label = "spl-boot-data1";
- reg = <0xFE0000 0x10000>;
- };
- partition@FF0000 {
- label = "spl-boot-data2";
- reg = <0xFF0000 0x10000>;
- };
- };
+ hog_pins_coding: hog@2 {
+ reg = <2>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D01__GPIO_0_1
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D04__GPIO_0_4
+ MX28_PAD_GPMI_D06__GPIO_0_6
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
-&usb0 {
- vbus-supply = <®_usb_5v>;
- status = "okay";
+®_fec_3v3 {
+ gpio = <&gpio0 0 0>;
};
-&usbphy0 {
- status = "okay";
+®_usb_5v {
+ gpio = <&gpio0 2 0>;
+};
+
+&spi2_pins_a {
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ >;
};
@@ -100,7 +100,7 @@
status = "disabled";
};
- gpmi: gpmi-nand@8000c000 {
+ gpmi: nand-controller@8000c000 {
compatible = "fsl,imx28-gpmi-nand";
#address-cells = <1>;
#size-cells = <1>;
@@ -110,6 +110,8 @@
interrupt-names = "bch";
clocks = <&clks 50>;
clock-names = "gpmi_io";
+ assigned-clocks = <&clks 13>;
+ assigned-clock-parents = <&clks 10>;
dmas = <&dma_apbh 4>;
dma-names = "rx-tx";
status = "disabled";
@@ -948,6 +950,16 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ usb1_pins_b: usb1@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM2__USB1_OVERCURRENT
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
usb0_id_pins_a: usb0id@0 {
reg = <0>;
fsl,pinmux-ids = <
@@ -998,7 +1010,7 @@
clocks = <&clks 26>;
};
- dcp: dcp@80028000 {
+ dcp: crypto@80028000 {
compatible = "fsl,imx28-dcp", "fsl,imx23-dcp";
reg = <0x80028000 0x2000>;
interrupts = <52 53 54>;
@@ -1011,7 +1023,7 @@
status = "disabled";
};
- ocotp: ocotp@8002c000 {
+ ocotp: efuse@8002c000 {
compatible = "fsl,imx28-ocotp", "fsl,ocotp";
#address-cells = <1>;
#size-cells = <1>;
@@ -1317,7 +1329,7 @@
status = "disabled";
};
- etn_switch: switch@800f8000 {
+ eth_switch: switch@800f8000 {
reg = <0x800f8000 0x8000>;
status = "disabled";
};
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Header providing constants for i.MX28 pinctrl bindings.
*
* Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_MXS_PINCTRL_H__