diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 6f8b7593d250..28f69e7c73d2 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -150,6 +150,11 @@ config TARGET_P2020RDB
 	imply CMD_SATA
 	imply SATA_SIL
 
+config TARGET_TURRIS_1X
+	bool "Support Turris 1.x"
+	select SUPPORT_SPL
+	select ARCH_P2020
+
 config TARGET_P2041RDB
 	bool "Support P2041RDB"
 	select ARCH_P2041
@@ -1201,6 +1206,7 @@ config SYS_FSL_LBC_CLK_DIV
 config FSL_VIA
 	bool
 
+source "board/CZ.NIC/turris_1x/Kconfig"
 source "board/emulation/qemu-ppce500/Kconfig"
 source "board/freescale/corenet_ds/Kconfig"
 source "board/freescale/mpc8548cds/Kconfig"
diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile
index a4b0d7ddc4ff..d6462101211e 100644
--- a/arch/powerpc/dts/Makefile
+++ b/arch/powerpc/dts/Makefile
@@ -26,6 +26,7 @@ dtb-$(CONFIG_TARGET_T2080QDS) += t2080qds.dtb
 dtb-$(CONFIG_TARGET_T2080RDB) += t2080rdb.dtb
 dtb-$(CONFIG_TARGET_T4240RDB) += t4240rdb.dtb
 dtb-$(CONFIG_TARGET_TUGE1) += kmtuge1.dtb
+dtb-$(CONFIG_TARGET_TURRIS_1X) += turris1x.dtb
 dtb-$(CONFIG_TARGET_TUXX1) += kmtuxa1.dtb
 dtb-$(CONFIG_TARGET_MCR3000) += mcr3000.dtb
 dtb-$(CONFIG_TARGET_GAZERBEAM) += gazerbeam.dtb
diff --git a/arch/powerpc/dts/turris1x-u-boot.dtsi b/arch/powerpc/dts/turris1x-u-boot.dtsi
new file mode 100644
index 000000000000..aa758818d564
--- /dev/null
+++ b/arch/powerpc/dts/turris1x-u-boot.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+&soc {
+	i2c@3000 {
+		u-boot,dm-pre-reloc;
+
+		crypto@64 {
+			u-boot,dm-pre-reloc;
+		};
+	};
+};
+
+#include "u-boot.dtsi"
diff --git a/arch/powerpc/dts/turris1x.dts b/arch/powerpc/dts/turris1x.dts
new file mode 100644
index 000000000000..12e08271e61f
--- /dev/null
+++ b/arch/powerpc/dts/turris1x.dts
@@ -0,0 +1,483 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Turris 1.x Device Tree Source
+ *
+ * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/)
+ *
+ * Pinout, Schematics and Altium hardware design files are open source
+ * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+/include/ "fsl/p2020si-pre.dtsi"
+
+/ {
+	model = "Turris 1.x";
+	compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		spi0 = &spi0;
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	soc: soc@ffe00000 {
+		ranges = <0x0 0x0 0xffe00000 0x00100000>;
+
+		i2c@3000 {
+			/* PCA9557PW GPIO controller for boot config */
+			gpio-controller@18 {
+				compatible = "nxp,pca9557";
+				label = "bootcfg";
+				reg = <0x18>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				polarity = <0x00>;
+			};
+
+			/* STM32F030R8T6 MCU for power control */
+			power-control@2a {
+				/*
+				 * Turris Power Control firmware runs on STM32F0 MCU.
+				 * This firmware is open source and available at:
+				 * https://gitlab.nic.cz/turris/hw/turris_power_control
+				 */
+				reg = <0x2a>;
+			};
+
+			/* DDR3 SPD/EEPROM PSWP instruction */
+			eeprom@32 {
+				reg = <0x32>;
+			};
+
+			/* SA56004ED temperature control */
+			temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */
+					     <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */
+			};
+
+			/* DDR3 SPD/EEPROM */
+			eeprom@52 {
+				compatible = "atmel,spd";
+				reg = <0x52>;
+			};
+
+			/* MCP79402-I/ST Protected EEPROM */
+			eeprom@57 {
+				reg = <0x57>;
+			};
+
+			/* ATSHA204-TH-DA-T crypto module */
+			crypto@64 {
+				compatible = "atmel,atsha204";
+				reg = <0x64>;
+			};
+
+			/* IDT6V49205BNLGI clock generator */
+			clock-generator@69 {
+				compatible = "idt,6v49205b";
+				reg = <0x69>;
+			};
+
+			/* MCP79402-I/ST RTC */
+			rtc@6f {
+				compatible = "microchip,mcp7940x";
+				reg = <0x6f>;
+				interrupt-parent = <&gpio>;
+				interrupts = <14 0>; /* GPIO14 - MFP pin */
+			};
+		};
+
+		/* SPI on connector P1 */
+		spi0: spi@7000 {
+		};
+
+		gpio: gpio-controller@fc00 {
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		/* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */
+		usb@22000 {
+			phy_type = "ulpi";
+			dr_mode = "host";
+		};
+
+		enet0: ethernet@24000 {
+			/* Connected to port 6 of QCA8337N-AL3C switch */
+			phy-connection-type = "rgmii-id";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		mdio@24520 {
+			/* KSZ9031RNXCA ethernet phy for WAN port */
+			phy: ethernet-phy@7 {
+				interrupts = <3 1 0 0>;
+				reg = <0x7>;
+			};
+
+			/* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */
+			switch@10 {
+				compatible = "qca,qca8337";
+				interrupts = <2 1 0 0>;
+				reg = <0x10>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "cpu1";
+						ethernet = <&enet1>;
+						phy-mode = "rgmii-id";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan5";
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan4";
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan3";
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan2";
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan1";
+					};
+
+					port@6 {
+						reg = <6>;
+						label = "cpu0";
+						ethernet = <&enet0>;
+						phy-mode = "rgmii-id";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+		};
+
+		ptp_clock@24e00 {
+			fsl,tclk-period = <5>;
+			fsl,tmr-prsc = <200>;
+			fsl,tmr-add = <0xcccccccd>;
+			fsl,tmr-fiper1 = <0x3b9ac9fb>;
+			fsl,tmr-fiper2 = <0x0001869b>;
+			fsl,max-adj = <249999999>;
+		};
+
+		enet1: ethernet@25000 {
+			/* Connected to port 0 of QCA8337N-AL3C switch */
+			phy-connection-type = "rgmii-id";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		mdio@25520 {
+			status = "disabled";
+		};
+
+		enet2: ethernet@26000 {
+			/* Connected to KSZ9031RNXCA ethernet phy (WAN port) */
+			label = "wan";
+			phy-handle = <&phy>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		mdio@26520 {
+			status = "disabled";
+		};
+
+		sdhc@2e000 {
+			bus-width = <4>;
+			cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	lbc: localbus@ffe05000 {
+		reg = <0 0xffe05000 0 0x1000>;
+
+		ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */
+			 <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */
+			 <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */
+
+		/* S29GL128P90TFIR10 NOR */
+		nor@0,0 {
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x01000000>;
+			bank-width = <2>;
+			device-width = <1>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					/* 128 kB for Device Tree Blob */
+					reg = <0x00000000 0x00020000>;
+					label = "dtb";
+				};
+
+				partition@20000 {
+					/* 1.7 MB for Rescue Linux Kernel Image */
+					reg = <0x00020000 0x001a0000>;
+					label = "rescue-kernel";
+				};
+
+				partition@1c0000 {
+					/* 1.5 MB for Rescue JFFS2 Root File System */
+					reg = <0x001c0000 0x00180000>;
+					label = "rescue-rootfs";
+				};
+
+				partition@340000 {
+					/* 11 MB for TAR.XZ Backup with content of NAND Root File System */
+					reg = <0x00340000 0x00b00000>;
+					label = "backup-rootfs";
+				};
+
+				partition@e40000 {
+					/* 768 kB for Certificates JFFS2 File System */
+					reg = <0x00e40000 0x000c0000>;
+					label = "certificates";
+				};
+
+				/* free unused space 0x00f00000-0x00f20000 */
+
+				partition@f20000 {
+					/* 128 kB for U-Boot Environment Variables */
+					reg = <0x00f20000 0x00020000>;
+					label = "u-boot-env";
+				};
+
+				partition@f40000 {
+					/* 768 kB for U-Boot Bootloader Image */
+					reg = <0x00f40000 0x000c0000>;
+					label = "u-boot";
+				};
+			};
+		};
+
+		/* MT29F2G08ABAEAWP:E NAND */
+		nand@1,0 {
+			compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand";
+			reg = <0x1 0x0 0x00040000>;
+			nand-ecc-mode = "soft";
+			nand-ecc-algo = "bch";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					/* 256 MB for UBI with one volume: UBIFS Root File System */
+					reg = <0x00000000 0x10000000>;
+					label = "rootfs";
+				};
+			};
+		};
+
+		/* LCMXO1200C-3FTN256C FPGA */
+		cpld@3,0 {
+			/*
+			 * Turris CPLD firmware which runs on this Lattice FPGA,
+			 * is extended version of P1021RDB-PC CPLD v4.1 firmware.
+			 * It is backward compatible with its original version
+			 * and the only extension is support for Turris LEDs.
+			 * Turris CPLD firmware is open source and available at:
+			 * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
+			 */
+			compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus", "syscon";
+			reg = <0x3 0x0 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x3 0x0 0x00020000>;
+
+			/* MAX6370KA+T watchdog */
+			watchdog@2 {
+				/*
+				 * CPLD firmware maps SET0, SET1 and SET2
+				 * input logic of MAX6370KA+T chip to CPLD
+				 * memory space at byte offset 0x2. WDI
+				 * input logic is outside of the CPLD and
+				 * connected via external GPIO.
+				 */
+				compatible = "maxim,max6370";
+				reg = <0x02 0x01>;
+				gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+			};
+
+			reboot@d {
+				compatible = "syscon-reboot";
+				reg = <0x0d 0x01>;
+				offset = <0x0d>;
+				mask = <0x01>;
+				value = <0x01>;
+			};
+
+			led-controller@13 {
+				/*
+				 * LEDs are controlled by CPLD firmware.
+				 * All five LAN LEDs share common RGB settings
+				 * and so it is not possible to set different
+				 * colors on different LAN ports.
+				 */
+				compatible = "cznic,turris1x-leds";
+				reg = <0x13 0x1d>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				multi-led@0 {
+					reg = <0x0>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WAN;
+				};
+
+				multi-led@1 {
+					reg = <0x1>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <5>;
+				};
+
+				multi-led@2 {
+					reg = <0x2>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <4>;
+				};
+
+				multi-led@3 {
+					reg = <0x3>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <3>;
+				};
+
+				multi-led@4 {
+					reg = <0x4>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <2>;
+				};
+
+				multi-led@5 {
+					reg = <0x5>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <1>;
+				};
+
+				multi-led@6 {
+					reg = <0x6>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WLAN;
+				};
+
+				multi-led@7 {
+					reg = <0x7>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_POWER;
+				};
+			};
+		};
+	};
+
+	pci2: pcie@ffe08000 {
+		/*
+		 * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller.
+		 * This xHCI controller is available only on Turris 1.1 boards.
+		 * Turris 1.0 boards have nothing connected to this PCIe bus,
+		 * so system would see only PCIe Root Port of this PCIe Root
+		 * Complex. TUSB7340RKM xHCI controller has four SuperSpeed
+		 * channels. Channel 0 is connected to the front USB 3.0 port,
+		 * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe
+		 * slot 1 (CN5), channels 2 and 3 to connector P600.
+		 *
+		 * P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller
+		 * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required.
+		 * So allocate 2MB of PCIe MEM for this PCIe bus.
+		 */
+		reg = <0 0xffe08000 0 0x1000>;
+		ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+
+	pci1: pcie@ffe09000 {
+		/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
+		reg = <0 0xffe09000 0 0x1000>;
+		ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+
+	pci0: pcie@ffe0a000 {
+		/*
+		 * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card.
+		 * Turris 1.1 boards have in this mPCIe slot additional USB 2.0
+		 * pins via channel 1 of TUSB7340RKM xHCI controller and also
+		 * additional SIM card slot, both for USB-based WWAN cards.
+		 */
+		reg = <0 0xffe0a000 0 0x1000>;
+		ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+};
+
+/include/ "fsl/p2020si-post.dtsi"
diff --git a/board/CZ.NIC/turris_1x/Kconfig b/board/CZ.NIC/turris_1x/Kconfig
new file mode 100644
index 000000000000..2a1cbd22c783
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/Kconfig
@@ -0,0 +1,170 @@
+# SPDX-License-Identifier: GPL-2.0+
+# (C) 2022 Pali Rohár <pali@kernel.org>
+
+if TARGET_TURRIS_1X
+
+# Board identification
+config SYS_BOARD
+	default "turris_1x"
+config SYS_VENDOR
+	default "CZ.NIC"
+config SYS_CONFIG_NAME
+	default "turris_1x"
+config DEFAULT_DEVICE_TREE
+	default "turris1x"
+
+# Board functions
+config ATSHA204A
+	default y
+config BOARD_EARLY_INIT_F
+	default y
+config BOARD_EARLY_INIT_R
+	default y
+config LAST_STAGE_INIT
+	default y
+config MISC
+	default y
+config OF_BOARD_FIXUP
+	default y
+config OF_BOARD_SETUP
+	default y
+
+# ENV
+config ENV_SIZE
+	default 0x2000
+config ENV_SECT_SIZE
+	default 0x20000
+config ENV_OVERWRITE
+	default y
+config ENV_IS_IN_FLASH
+	default y
+config ENV_ADDR
+	default 0xeff20000 # in NOR
+config SYS_RELOC_GD_ENV_ADDR
+	default y
+
+# DDR
+config DDR_CLK_FREQ
+	default 66666666
+
+# UART
+config DEBUG_UART_BASE
+	default 0xffe04500 if DEBUG_UART
+config DEBUG_UART_CLOCK
+	default 37500000 if DEBUG_UART
+config SYS_NS16550
+	default y
+
+# I2C
+config I2C_SET_DEFAULT_BUS_NUM
+	default y
+config SYS_FSL_I2C_OFFSET
+	default 0x3000
+config SYS_FSL_HAS_I2C2_OFFSET
+	default y
+config SYS_FSL_I2C2_OFFSET
+	default 0x3100
+config SYS_I2C_FSL
+	default y
+
+# GPIO
+config MPC8XXX_GPIO
+	default y
+
+# WDT
+config WDT_MAX6370
+	default y
+
+# PCIe
+config PCI_INIT_R
+	default y
+config PCIE_FSL
+	default y
+
+# Ethernet
+config MII
+	default y
+config PHY_FIXED
+	default y
+config TSEC_ENET
+	default y
+
+# USB
+config USB_EHCI_FSL
+	default y
+config USB_XHCI_HCD
+	default y
+config USB_XHCI_PCI
+	default y
+
+# SDHC
+config FSL_ESDHC
+	default y
+config FSL_PREPBL_ESDHC_BOOT_SECTOR
+	default y if SYS_EXTRA_OPTIONS = SDCARD
+config SYS_FSL_ESDHC_DEFAULT_BUS_WIDTH
+	default 4
+
+# NOR
+config MTD_NOR_FLASH
+	default y
+config CFI_FLASH
+	default y
+config FLASH_CFI_MTD
+	default y
+config SYS_FLASH_USE_BUFFER_WRITE
+	default y
+
+# NAND
+config MTD_RAW_NAND
+	default y
+config NAND_FSL_ELBC
+	default y
+config NAND_FSL_ELBC_DT
+	default y
+config BCH
+	default y
+config SYS_FLASH_CFI
+	default y
+
+config MPC85XX_HAVE_RESET_VECTOR
+	default y if SYS_EXTRA_OPTIONS != SDCARD
+
+config SYS_LOAD_ADDR
+	default 0x1000000
+
+config SYS_TEXT_BASE
+	default 0x11000000 if SPL # in DDR
+	default 0xf8f80000 if SYS_EXTRA_OPTIONS = SDCARD # in SRAM
+	default 0xeff40000 # in NOR
+
+if SPL
+
+config SPL_TEXT_BASE
+	default 0xf8f80000 if SYS_EXTRA_OPTIONS = SDCARD # in SRAM
+	default 0xeff40000 # in NOR
+
+config SPL_ENV_SUPPORT
+	default y
+config SPL_FRAMEWORK
+	default n
+config SPL_I2C
+	default y
+config SPL_LIBCOMMON_SUPPORT
+	default y
+config SPL_LIBGENERIC_SUPPORT
+	default y
+config SPL_MMC
+	default y if SYS_EXTRA_OPTIONS = SDCARD
+config SPL_MMC_BOOT
+	default y if SYS_EXTRA_OPTIONS = SDCARD
+config SPL_MPC8XXX_INIT_DDR
+	default y
+config SPL_SERIAL
+	default y
+config SPL_SYS_I2C_LEGACY
+	default y
+
+endif
+
+endif
diff --git a/board/CZ.NIC/turris_1x/MAINTAINERS b/board/CZ.NIC/turris_1x/MAINTAINERS
new file mode 100644
index 000000000000..8ca941c95e8e
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/MAINTAINERS
@@ -0,0 +1,13 @@
+TURRIS 1.X BOARD
+M:	Pali Rohár <pali@kernel.org>
+S:	Maintained
+F:	arch/powerpc/dts/turris1x-u-boot.dtsi
+F:	arch/powerpc/dts/turris1x.dts
+F:	board/CZ.NIC/turris_1x/
+F:	board/CZ.NIC/turris_atsha_otp.c
+F:	board/CZ.NIC/turris_atsha_otp.h
+F:	board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+F:	board/freescale/p1_p2_rdb_pc/spl.c
+F:	configs/turris_1x_nor_defconfig
+F:	configs/turris_1x_sdcard_defconfig
+F:	include/configs/turris_1x.h
diff --git a/board/CZ.NIC/turris_1x/Makefile b/board/CZ.NIC/turris_1x/Makefile
new file mode 100644
index 000000000000..4af77bb52195
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0+
+# (C) 2022 Pali Rohár <pali@kernel.org>
+
+ifdef CONFIG_SPL_BUILD
+obj-y	+= ../../freescale/p1_p2_rdb_pc/spl.o
+endif
+
+obj-y	+= ../../freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.o
+obj-y	+= ../turris_atsha_otp.o
+
+obj-y	+= turris_1x.o
+obj-y	+= ddr.o
+obj-y	+= law.o
+obj-y	+= tlb.o
diff --git a/board/CZ.NIC/turris_1x/ddr.c b/board/CZ.NIC/turris_1x/ddr.c
new file mode 100644
index 000000000000..ced4e97bfa30
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/ddr.c
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0+
+// (C) 2022 Pali Rohár <pali@kernel.org>
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, unsigned int ctrl_num)
+{
+	int i;
+
+	popts->clk_adjust = 6;
+	popts->cpo_override = 0x1f;
+	popts->write_data_delay = 2;
+	popts->half_strength_driver_enable = 1;
+	popts->wrlvl_en = 1;
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+	popts->wrlvl_start = 0x8;
+	popts->trwt_override = 1;
+	popts->trwt = 0;
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+		popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+	}
+}
diff --git a/board/CZ.NIC/turris_1x/law.c b/board/CZ.NIC/turris_1x/law.c
new file mode 100644
index 000000000000..1502ceecf823
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/law.c
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+// (C) 2022 Pali Rohár <pali@kernel.org>
+
+#include <common.h>
+#include <asm/fsl_law.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/CZ.NIC/turris_1x/tlb.c b/board/CZ.NIC/turris_1x/tlb.c
new file mode 100644
index 000000000000..26caa3e624b8
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/tlb.c
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0+
+// (C) 2022 Pali Rohár <pali@kernel.org>
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <linux/sizes.h>
+#include <linux/build_bug.h>
+
+/*
+ * NOTE: e500v2 supports only following Book-E page sizes:
+ *
+ * TLB0:
+ * BOOKE_PAGESZ_4K
+ *
+ * TLB1:
+ * BOOKE_PAGESZ_4K
+ * BOOKE_PAGESZ_16K
+ * BOOKE_PAGESZ_64K
+ * BOOKE_PAGESZ_256K
+ * BOOKE_PAGESZ_1M
+ * BOOKE_PAGESZ_4M
+ * BOOKE_PAGESZ_16M
+ * BOOKE_PAGESZ_64M
+ * BOOKE_PAGESZ_256M
+ * BOOKE_PAGESZ_1G
+ * BOOKE_PAGESZ_4G
+ */
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 */
+
+	/* ***** - Initial stack in L1 cache 16K */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 0 * SZ_4K,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 0 * SZ_4K,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 1 * SZ_4K ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 1 * SZ_4K,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 2 * SZ_4K ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 2 * SZ_4K,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 3 * SZ_4K ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 3 * SZ_4K,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+
+	/* *I*** - Boot page 4K */
+	SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR,
+			0xfffff000,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+			0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSR 1M */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR,
+			CONFIG_SYS_CCSRBAR_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 1, BOOKE_PAGESZ_1M, 1),
+
+	/* W**G* - NOR 16M */
+	/* This will be changed to *I*G* after relocation to RAM in board_early_init_r() */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE,
+			CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+			0, 2, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - CPLD 256K (effective 128K) */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE,
+			CONFIG_SYS_CPLD_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 3, BOOKE_PAGESZ_256K, 1),
+
+	/* *I*G* - NAND 256K */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE,
+			CONFIG_SYS_NAND_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 4, BOOKE_PAGESZ_256K, 1),
+
+	/* *I*G* - PCIe MEM (bus 1 and 2) 1G */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT,
+			CONFIG_SYS_PCIE1_MEM_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 5, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCIe MEM (bus 3) 4M (effective 2M) */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT,
+			CONFIG_SYS_PCIE3_MEM_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 6, BOOKE_PAGESZ_4M, 1),
+
+	/* *I*G* - PCIe I/O (all 3 buses) 256K (effective 192K) */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT,
+			CONFIG_SYS_PCIE1_IO_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 7, BOOKE_PAGESZ_256K, 1),
+
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+	/* ***G* - Initial SRAM in L2 cache 512K */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR,
+			CONFIG_SYS_INIT_L2_ADDR_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+			0, 8, BOOKE_PAGESZ_256K, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + SZ_256K,
+			CONFIG_SYS_INIT_L2_ADDR_PHYS + SZ_256K,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+			0, 9, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
+	/* **M** - SDRAM 2G */
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
+			CONFIG_SYS_DDR_SDRAM_BASE,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+			0, 10, BOOKE_PAGESZ_1G, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + SZ_1G,
+			CONFIG_SYS_DDR_SDRAM_BASE + SZ_1G,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+			0, 11, BOOKE_PAGESZ_1G, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
+
+/*
+ * PCIe MEM TLB entry expects that second PCIe MEM window is mapped after the
+ * first PCIe MEM window. Check for this requirement.
+ */
+static_assert(CONFIG_SYS_PCIE2_MEM_VIRT == CONFIG_SYS_PCIE1_MEM_VIRT + SZ_512M);
+static_assert(CONFIG_SYS_PCIE2_MEM_PHYS == CONFIG_SYS_PCIE1_MEM_PHYS + SZ_512M);
+
+/*
+ * PCIe I/O TLB entry expects that all 3 PCIe I/O windows are mapped one after
+ * another. Check for this requirement.
+ */
+static_assert(CONFIG_SYS_PCIE2_IO_VIRT == CONFIG_SYS_PCIE1_IO_VIRT + SZ_64K);
+static_assert(CONFIG_SYS_PCIE2_IO_PHYS == CONFIG_SYS_PCIE1_IO_PHYS + SZ_64K);
+static_assert(CONFIG_SYS_PCIE3_IO_VIRT == CONFIG_SYS_PCIE2_IO_VIRT + SZ_64K);
+static_assert(CONFIG_SYS_PCIE3_IO_PHYS == CONFIG_SYS_PCIE2_IO_PHYS + SZ_64K);
diff --git a/board/CZ.NIC/turris_1x/turris_1x.c b/board/CZ.NIC/turris_1x/turris_1x.c
new file mode 100644
index 000000000000..782acdcd1d3d
--- /dev/null
+++ b/board/CZ.NIC/turris_1x/turris_1x.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0+
+// (C) 2022 Pali Rohár <pali@kernel.org>
+
+#include <common.h>
+#include <init.h>
+#include <env.h>
+
+#include "../turris_atsha_otp.h"
+
+/*
+ * Reset time cycle register provided by Turris CPLD firmware.
+ * Turris CPLD firmware is open source and available at:
+ * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
+ */
+#define TURRIS_CPLD_RESET_TIME_CYCLE_REG	((void *)CONFIG_SYS_CPLD_BASE + 0x1f)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_300MS	BIT(0)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_1S	BIT(1)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_2S	BIT(2)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_3S	BIT(3)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_4S	BIT(4)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_5S	BIT(5)
+#define  TURRIS_CPLD_RESET_TIME_CYCLE_6S	BIT(6)
+
+#define TURRIS_CPLD_LED_BRIGHTNESS_REG_FIRST	((void *)CONFIG_SYS_CPLD_BASE + 0x13)
+#define TURRIS_CPLD_LED_BRIGHTNESS_REG_LAST	((void *)CONFIG_SYS_CPLD_BASE + 0x1e)
+#define TURRIS_CPLD_LED_SW_OVERRIDE_REG		((void *)CONFIG_SYS_CPLD_BASE + 0x22)
+
+int misc_init_r(void)
+{
+	turris_atsha_otp_init_mac_addresses(0);
+	return 0;
+}
+
+int show_board_info(void)
+{
+	u32 version_num, serial_num;
+	void *reg;
+	int err;
+
+	/* Disable software control of all Turris LEDs */
+	out_8(TURRIS_CPLD_LED_SW_OVERRIDE_REG, 0x00);
+
+	/* Reset colors of all Turris LEDs to their default values */
+	for (reg = TURRIS_CPLD_LED_BRIGHTNESS_REG_FIRST;
+	     reg <= TURRIS_CPLD_LED_BRIGHTNESS_REG_LAST;
+	     reg++)
+		out_8(reg, 0xff);
+
+	err = turris_atsha_otp_get_serial_number(&version_num, &serial_num);
+
+	/*
+	 * Turris 1.0 boards have version_num 0x5.
+	 * Turris 1.1 boards have version_num 0x6, 0x7, 0x8 and 0x9.
+	 */
+	printf("Model: Turris 1.%c\n", err ? 'x' :
+	       (be32_to_cpu(version_num) >= 0x6) ? '1' : '0');
+
+	if (err)
+		printf("Serial Number: unknown\n");
+	else
+		printf("Serial Number: %08X%08X\n", be32_to_cpu(version_num),
+		       be32_to_cpu(serial_num));
+
+	err = checkboard();
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static void handle_reset_button(void)
+{
+	const char * const vars[1] = { "bootcmd_rescue", };
+	char rescue_env_name[] = "bootcmd_rescueXs";
+	u8 reset_time_hold;
+	u8 reset_time_val;
+
+	/*
+	 * Ensure that bootcmd_rescue has always stock value, so that running
+	 *   run bootcmd_rescue
+	 * always works correctly.
+	 */
+	env_set_default_vars(1, (char * const *)vars, 0);
+
+	reset_time_val = in_8(TURRIS_CPLD_RESET_TIME_CYCLE_REG);
+	if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_6S)
+		reset_time_hold = 6;
+	else if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_5S)
+		reset_time_hold = 5;
+	else if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_4S)
+		reset_time_hold = 4;
+	else if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_3S)
+		reset_time_hold = 3;
+	else if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_2S)
+		reset_time_hold = 2;
+	else if (reset_time_val & TURRIS_CPLD_RESET_TIME_CYCLE_1S)
+		reset_time_hold = 1;
+	else
+		reset_time_hold = 0;
+
+	rescue_env_name[sizeof(rescue_env_name)-3] = '0' + reset_time_hold;
+
+	if (reset_time_hold == 6) {
+		/* Red reset button was hold for at least six seconds. */
+		const char * const vars[2] = {
+			"bootcmd",
+			"distro_bootcmd",
+		};
+
+		/*
+		 * Set the above envs to their default values, in case the user
+		 * managed to break them.
+		 */
+		env_set_default_vars(2, (char * const *)vars, 0);
+
+		/* Ensure bootcmd_rescue is used by distroboot */
+		env_set("boot_targets", "rescue");
+
+		printf("RESET button was hold for >= 6s, overwriting boot_targets for system rescue!\n");
+	} else if (reset_time_hold && env_get(rescue_env_name)) {
+		/*
+		 * Red reset button was hold for less than six seconds and
+		 * custom user rescue target bootcmd_rescueXs exists in env.
+		 * Set bootcmd_rescueXs as default distroboot target.
+		 */
+		env_set("boot_targets", rescue_env_name + sizeof("bootcmd_") - 1);
+		printf("RESET button was hold for %us, overwriting boot_targets for custom user env target %s!\n",
+		       reset_time_hold, rescue_env_name);
+	} else {
+		/*
+		 * In case the user somehow managed to save environment with
+		 * boot_targets=rescue, reset boot_targets to default value.
+		 * This could happen in subsequent commands if bootcmd_rescue
+		 * failed.
+		 */
+		if (!strcmp(env_get("boot_targets"), "rescue")) {
+			const char * const vars[1] = {
+				"boot_targets",
+			};
+
+			env_set_default_vars(1, (char * const *)vars, 0);
+		}
+
+		if (reset_time_hold) {
+			printf("RESET button was hold for %us, but custom user env target %s is not defined.\n",
+			       reset_time_hold, rescue_env_name);
+			printf("Continue normal booting...\n");
+		}
+	}
+}
+
+int last_stage_init(void)
+{
+	handle_reset_button();
+	return 0;
+}
diff --git a/configs/turris_1x_nor_defconfig b/configs/turris_1x_nor_defconfig
new file mode 100644
index 000000000000..593dacebce56
--- /dev/null
+++ b/configs/turris_1x_nor_defconfig
@@ -0,0 +1,57 @@
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+# CONFIG_CMD_ERRATA is not set
+CONFIG_TARGET_TURRIS_1X=y
+CONFIG_AHCI=y
+CONFIG_OPTIMIZE_INLINING=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_MP=y
+CONFIG_FIT=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=3
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run distro_bootcmd"
+CONFIG_USE_PREBOOT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_EEPROM is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_TFTPPUT=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+# CONFIG_DM_WARN is not set
+# CONFIG_DM_DEVICE_REMOVE is not set
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_DM_I2C=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_NVME_PCI=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_WDT=y
+CONFIG_UBIFS_SILENCE_DEBUG_DUMP=y
+# CONFIG_BINMAN_FDT is not set
diff --git a/configs/turris_1x_sdcard_defconfig b/configs/turris_1x_sdcard_defconfig
new file mode 100644
index 000000000000..c0bee1ebb214
--- /dev/null
+++ b/configs/turris_1x_sdcard_defconfig
@@ -0,0 +1,63 @@
+CONFIG_PPC=y
+CONFIG_SPL=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_TURRIS_1X=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_MP=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="SDCARD"
+CONFIG_BOOTDELAY=3
+CONFIG_USE_PREBOOT=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_SHA1SUM=y
+CONFIG_CMD_LZMADEC=y
+CONFIG_CMD_UNLZ4=y
+CONFIG_CMD_UNZIP=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_BTRFS=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_SQUASHFS=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x52
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_NVME_PCI=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_ESPI=y
+CONFIG_USB=y
+CONFIG_WDT=y
+CONFIG_FAT_WRITE=y
diff --git a/include/configs/turris_1x.h b/include/configs/turris_1x.h
new file mode 100644
index 000000000000..c53bed028c7a
--- /dev/null
+++ b/include/configs/turris_1x.h
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: GPL-2.0+
+// (C) 2022 Pali Rohár <pali@kernel.org>
+
+#ifndef _CONFIG_TURRIS_1X_H
+#define _CONFIG_TURRIS_1X_H
+
+#include <linux/sizes.h>
+
+/*
+ * Turris 1.x memory map:
+ *
+ * 0x0000_0000 - 0x7fff_ffff    2 GB  DDR                 cacheable
+ * 0x8000_0000 - 0xbfff_ffff    1 GB  PCIe MEM (bus 1-2)  non-cacheable
+ * 0xc000_0000 - 0xc01f_ffff    2 MB  PCIe MEM (bus 3)    non-cacheable
+ * 0xc020_0000 - 0xeeff_ffff  750 MB  unused
+ * 0xef00_0000 - 0xefff_ffff   16 MB  NOR (CS0)           non-cacheable
+ * 0xf000_0000 - 0xf8f7_ffff  143 MB  unused
+ * 0xf8f8_0000 - 0xf8ff_ffff  512 kB  L2 SRAM             cacheable (early boot, SD card only)
+ * 0xf900_0000 - 0xff6f_ffff  103 MB  unused
+ * 0xff70_0000 - 0xff7f_ffff    1 MB  CCSR                non-cacheable (SPL only)
+ * 0xff80_0000 - 0xff80_7fff   32 kB  NAND (CS1)          non-cacheable
+ * 0xffa0_0000 - 0xffa1_ffff  128 kB  CPLD (CS3)          non-cacheable
+ * 0xffc0_0000 - 0xffc2_ffff  192 kB  PCIe IO             non-cacheable
+ * 0xffd0_0000 - 0xffd0_3fff   16 kB  L1 stack            cacheable (early boot)
+ * 0xffe0_0000 - 0xffef_ffff    1 MB  CCSR                non-cacheable (not in SPL)
+ * 0xffff_f000 - 0xffff_ffff    4 kB  Boot page           non-cacheable
+ */
+
+/*
+ * Global settings
+ */
+
+/*
+ * CONFIG_ENABLE_36BIT_PHYS needs to be always defined when processor supports
+ * 36-bit addressing (which is case for P2020), also when only 32-bit addressing
+ * mode is used. Name of this config option is misleading and should have been
+ * called SUPPORT instead of ENABLE.
+ * When CONFIG_PHYS_64BIT is set then 36-bit addressing is used, when unset then
+ * 32-bit addressing is used. Name of this config option is misleading too and
+ * should have been called 36BIT and ENABLED, not 64BIT.
+ * Due to performance reasons (see document AN4064), Turris 1.x boards use only
+ * 32-bit addressing. Also all config options are currently defined only for
+ * 32-bit addressing, so compiling U-Boot for 36-bit addressing is not possible
+ * yet.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS
+#ifdef CONFIG_PHYS_64BIT
+#error "36-bit addressing is not implemented for this board"
+#endif
+
+#define CONFIG_HWCONFIG
+#define CONFIG_L2_CACHE
+#define CONFIG_SYS_L2_SIZE		SZ_512K
+#define CONFIG_BTB			/* Enable Branch Prediction */
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN		CONFIG_BOARD_SIZE_LIMIT
+
+/*
+ * Boot settings
+ */
+
+#ifdef CONFIG_SDCARD
+
+/*
+ * Booting from SD card
+ * BootROM configures L2 cache as SRAM, loads image from SD card into L2 SRAM
+ * and starts executing directly _start entry point in L2 SRAM. Therefore reset
+ * vector is not used and maximal size of the image is L2 cache size. For builds
+ * with SPL there is no limit of U-Boot proper as BootROM loads SPL which then
+ * loads U-Boot proper directly into DDR.
+ */
+
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+
+/* For SD card builds without SPL it is needed to set CONFIG_SYS_RAMBOOT */
+#ifndef CONFIG_SPL
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_PAD_TO		0
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR
+#define CONFIG_SPL_MAX_SIZE		(CONFIG_SYS_L2_SIZE + CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * SZ_512)
+#else
+#define CONFIG_SPL_MAX_SIZE		CONFIG_SYS_L2_SIZE
+#endif
+#define CONFIG_SYS_MMC_U_BOOT_SIZE	CONFIG_BOARD_SIZE_LIMIT
+#define CONFIG_SYS_MMC_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MMC_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#endif
+
+#else
+
+/*
+ * Booting from NOR
+ * Last 4kB page of the NOR is mapped into CPU address space and CPU starts
+ * executing last instruction of that page, which is reset vector address.
+ * We have 16 MB large NOR memory, so define correct reset vector address.
+ */
+
+#define CONFIG_RESET_VECTOR_ADDRESS	(CONFIG_SYS_FLASH_BASE + SZ_16M - 4)
+
+#endif
+
+/*
+ * CONFIG_BOARD_SIZE_LIMIT must be hex number because it is used in Makefile.
+ * For NOR build, size of the U-Boot binary must always be 768 kB.
+ * For SD card build with SPL, there is no limit, just broken build system which
+ * cannot fill CONFIG_SYS_MMC_U_BOOT_SIZE and CONFIG_SYS_MONITOR_LEN values
+ * automatically. So choose it as lowest value as possible with which build
+ * process does not fail, to minimize final binary size.
+ * For SD card build without SPL, there is upper limit of L2 cache size.
+ */
+#ifndef CONFIG_SDCARD
+#define CONFIG_BOARD_SIZE_LIMIT		0x000c0000 /* 768 kB */
+#elif defined(CONFIG_SPL)
+#define CONFIG_BOARD_SIZE_LIMIT		0x00100000 /* 1 MB */
+#else
+#define CONFIG_BOARD_SIZE_LIMIT		0x00080000 /* 512 kB - must be same as CONFIG_SYS_L2_SIZE */
+#endif
+
+/*
+ * Initial stack in L1 cache
+ */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#define CONFIG_SYS_INIT_RAM_SIZE	SZ_16K
+#define CONFIG_SYS_INIT_RAM_LOCK
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Initial SRAM in L2 cache
+ */
+
+/* Initial SRAM is used only for SD card boot in first stage image */
+#ifdef CONFIG_SDCARD
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+#define CONFIG_SYS_INIT_L2_ADDR		0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS	CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SPL_RELOC_TEXT_BASE	CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L2_ADDR + 112 * SZ_1K)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SYS_INIT_L2_ADDR + 116 * SZ_1K)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SYS_INIT_L2_ADDR + 148 * SZ_1K)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(364 * SZ_1K)
+#endif
+#endif
+
+/*
+ * CCSR
+ */
+
+#define CONFIG_SYS_CCSRBAR		0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+/*
+ * U-Boot _start code expects that if CCSRBAR is configured to its default
+ * location and automatically relocate it to the new CONFIG_SYS_CCSRBAR_PHYS
+ * location. Relocation to the new location can be skipped by defining macro
+ * CONFIG_SYS_CCSR_DO_NOT_RELOCATE.
+ *
+ * All addresses in device tree are set to according the new relocated CCSRBAR.
+ * So device tree code cannot be used when CONFIG_SYS_CCSR_DO_NOT_RELOCATE is
+ * set.
+ *
+ * If CCSRBAR is not configured to its default location then _start code hangs
+ * or crashes.
+ *
+ * So relocation of CCSRBAR must be disabled in every code which runs before
+ * U-Boot proper (e.g. SPL), otherwise U-Boot proper's _start code crashes.
+ */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#endif
+
+/*
+ * DDR
+ */
+
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+#define CONFIG_SYS_SPD_BUS_NUM		0
+#define CONFIG_SYS_I2C_PCA9557_ADDR	0x18
+#define SPD_EEPROM_ADDRESS		0x52
+
+/*
+ * NOR
+ */
+
+#define CONFIG_SYS_FLASH_BASE		0xef000000
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_BR0_PRELIM		(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_MS_GPCM | BR_V)
+#define CONFIG_SYS_OR0_PRELIM		(OR_AM_16MB | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CONFIG_FLASH_SHOW_PROGRESS	45    /* count down from 45/5: 9..1 */
+#define CONFIG_SYS_MAX_FLASH_SECT	128   /* 16 MB */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500   /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_QUIET_TEST
+
+/*
+ * NAND
+ */
+
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_BR1_PRELIM		(BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) | BR_PS_8 | BR_MS_FCM | BR_V)
+#define CONFIG_SYS_OR1_PRELIM		(OR_AM_256KB | OR_FCM_PGS | OR_FCM_CSCT | OR_FCM_CST | OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_TRLX | OR_FCM_EHTR)
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_OR_PRELIM	CONFIG_SYS_OR1_PRELIM
+#define CONFIG_NAND_ECC_BCH
+
+/*
+ * CPLD
+ */
+
+#define CONFIG_SYS_CPLD_BASE		0xffa00000
+#define CONFIG_SYS_CPLD_BASE_PHYS	CONFIG_SYS_CPLD_BASE
+
+#define CONFIG_SYS_BR3_PRELIM		(BR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) | BR_PS_8 | BR_MS_GPCM | BR_V)
+#define CONFIG_SYS_OR3_PRELIM		(OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+/*
+ * Serial Port
+ */
+
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_CCSRBAR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_CCSRBAR + 0x4600)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 600, 1200, 1800, 2400, 4800, 9600, \
+					  19200, 38400, 57600, 115200, 230400, \
+					  460800, 500000, 576000, 921600, \
+					  1000000, 1500000, 2000000, 3000000 }
+
+/*
+ * PCIe
+ */
+
+/* PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card */
+#define CONFIG_PCIE1
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_VIRT
+#define CONFIG_SYS_PCIE1_IO_PHYS	CONFIG_SYS_PCIE1_IO_VIRT
+
+/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
+#define CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_VIRT
+#define CONFIG_SYS_PCIE2_IO_PHYS	CONFIG_SYS_PCIE2_IO_VIRT
+
+/* PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller */
+#define CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xc0000000
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc20000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	CONFIG_SYS_PCIE3_MEM_VIRT
+#define CONFIG_SYS_PCIE3_IO_PHYS	CONFIG_SYS_PCIE3_IO_VIRT
+
+#define CONFIG_PCI_SCAN_SHOW		/* Show pci devices on startup */
+
+/*
+ * Ethernet
+ */
+
+#define CONFIG_ETHPRIME			"eth2" /* Primary ethernet device */
+
+/*
+ * USB
+ */
+
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
+/*
+ * eSDHC
+ */
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define SDHC_WP_IS_GPIO			/* SDHC_WP pin is not connected to SD card slot, it is GPIO pin */
+
+/*
+ * ATA/SCSI
+ */
+
+#define CONFIG_LBA48			/* Enable support for 137+ GB disks */
+#define CONFIG_SYS_64BIT_LBA		/* Enable support for 2.1+ TB disks */
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* Allow baudrate change argument for loads */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		SZ_64M /* Initial Memory for Linux */
+#define CONFIG_SYS_BOOTM_LEN		SZ_64M /* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(NVME, nvme, 0) \
+	func(SCSI, scsi, 0) \
+	func(USB, usb, 0) \
+	func(USB, usb, 1) \
+	func(USB, usb, 2) \
+	func(USB, usb, 3) \
+	func(USB, usb, 4) \
+	func(UBIFS, ubifs, 0, rootfs, rootfs, 512) \
+	func(UBIFS, ubifs, 1, rootfs, rootfs, 2048) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+/* These boot source switches macros must be constant numbers as they are stringified */
+#define __SW_BOOT_MASK			0x03
+#define __SW_BOOT_NOR			0xc8
+#define __SW_BOOT_SPI			0x28
+#define __SW_BOOT_SD			0x68
+#define __SW_BOOT_SD2			0x18
+#define __SW_BOOT_NAND			0xe8
+#define __SW_BOOT_PCIE			0xa8
+#define __SW_NOR_BANK_MASK		0xfd
+#define __SW_NOR_BANK_UP		0x00
+#define __SW_NOR_BANK_LO		0x02
+#define __SW_BOOT_NOR_BANK_UP		0xc8 /* (__SW_BOOT_NOR | __SW_NOR_BANK_UP) */
+#define __SW_BOOT_NOR_BANK_LO		0xca /* (__SW_BOOT_NOR | __SW_NOR_BANK_LO) */
+#define __SW_BOOT_NOR_BANK_MASK		0x01 /* (__SW_BOOT_MASK & __SW_NOR_BANK_MASK) */
+
+#include "p1_p2_bootsrc.h"
+
+#define REBOOT_ENV_SETTINGS \
+	RST_NOR_UP_CMD(reboot_to_nor, echo Rebooting to NOR bootloader;) \
+	RST_SD_CMD(reboot_to_sd, echo Rebooting to SD bootloader;) \
+	RST_DEF_CMD(reboot_to_def, echo Rebooting to default bootloader;) \
+	""
+
+#define BOOTCMD_RESCUE \
+	"setenv bootargs root=mtd2 ro rootfstype=jffs2 console=ttyS0,115200; " \
+	"mw.b 0xffa00002 0x03; " \
+	"bootm 0xef020000 - 0xef000000" \
+	""
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"fdt_addr_r=0x2000000\0" \
+	"kernel_addr_r=0x2100000\0" \
+	"scriptaddr=0x3000000\0" \
+	"pxefile_addr_r=0x3100000\0" \
+	"ramdisk_addr_r=0x4000000\0" \
+	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	"fdt_addr=0xef000000\0" \
+	"bootcmd_rescue=" BOOTCMD_RESCUE "\0" \
+	REBOOT_ENV_SETTINGS \
+	BOOTENV
+
+#endif /* _CONFIG_TURRIS_1X_H */
