Message ID | 20220209025623.30988-1-mibodhi@gmail.com |
---|---|
State | Accepted |
Commit | d2a44ceddc2bc603cf97c27c9d1491ffc1b58a48 |
Delegated to: | Stefan Roese |
Headers | show |
Series | arm: kirkwood: Pogoplug E02 : Convert Ethernet to Driver Model | expand |
On 2/9/22 03:56, Tony Dinh wrote: > The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert > to Driver Model and use uclass mvgbe and the compatible driver M88E1118R > to bring up Ethernet. > > - Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL > to bring up Ethernet. > - Currently, CONFIG_RESET_PHY_R symbol is used in > arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood > boards with mv8831116 PHY, with each board defines the function > reset_phy(). Undefine it for this board. > - As the result of the migration to Driver Model, this u-boot image has > grown substantially (about 100K, give or take). The old envs location > at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K). > - Miscellaneous changes: Move constants to .c file and remove header file > board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to > keep u-boot image under 512K, use BIT macro, and cleanup comments. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Thanks, Stefan > --- > > board/cloudengines/pogo_e02/pogo_e02.c | 51 +++++++------------------- > board/cloudengines/pogo_e02/pogo_e02.h | 29 --------------- > configs/pogo_e02_defconfig | 6 ++- > include/configs/pogo_e02.h | 13 ++----- > 4 files changed, 22 insertions(+), 77 deletions(-) > delete mode 100644 board/cloudengines/pogo_e02/pogo_e02.h > > diff --git a/board/cloudengines/pogo_e02/pogo_e02.c b/board/cloudengines/pogo_e02/pogo_e02.c > index 039fd6e3dd..59e1218b41 100644 > --- a/board/cloudengines/pogo_e02/pogo_e02.c > +++ b/board/cloudengines/pogo_e02/pogo_e02.c > @@ -1,5 +1,6 @@ > // SPDX-License-Identifier: GPL-2.0+ > /* > + * Copyright (C) 2022 Tony Dinh <mibodhi@gmail.com> > * Copyright (C) 2012 > * David Purdy <david.c.purdy@gmail.com> > * > @@ -12,16 +13,21 @@ > #include <common.h> > #include <init.h> > #include <log.h> > -#include <miiphy.h> > -#include <net.h> > +#include <netdev.h> > #include <asm/arch/cpu.h> > #include <asm/arch/soc.h> > #include <asm/arch/mpp.h> > #include <asm/global_data.h> > -#include "pogo_e02.h" > +#include <linux/bitops.h> > > DECLARE_GLOBAL_DATA_PTR; > > +/* GPIO configuration */ > +#define POGO_E02_OE_LOW (~(0)) > +#define POGO_E02_OE_HIGH (~(0)) > +#define POGO_E02_OE_VAL_LOW BIT(29) > +#define POGO_E02_OE_VAL_HIGH 0 > + > int board_early_init_f(void) > { > /* > @@ -64,6 +70,11 @@ int board_early_init_f(void) > return 0; > } > > +int board_eth_init(struct bd_info *bis) > +{ > + return cpu_eth_init(bis); > +} > + > int board_init(void) > { > /* Boot parameters address */ > @@ -71,37 +82,3 @@ int board_init(void) > > return 0; > } > - > -#ifdef CONFIG_RESET_PHY_R > -/* Configure and initialize PHY */ > -void reset_phy(void) > -{ > - u16 reg; > - u16 devadr; > - char *name = "egiga0"; > - > - if (miiphy_set_current_dev(name)) > - return; > - > - /* command to read PHY dev address */ > - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > - printf("Err..(%s) could not read PHY dev address\n", __func__); > - return; > - } > - > - /* > - * Enable RGMII delay on Tx and Rx for CPU port > - * Ref: sec 4.7.2 of chip datasheet > - */ > - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); > - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); > - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); > - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); > - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); > - > - /* reset the phy */ > - miiphy_reset(name, devadr); > - > - debug("88E1116 Initialized on %s\n", name); > -} > -#endif /* CONFIG_RESET_PHY_R */ > diff --git a/board/cloudengines/pogo_e02/pogo_e02.h b/board/cloudengines/pogo_e02/pogo_e02.h > deleted file mode 100644 > index c8397b4d4f..0000000000 > --- a/board/cloudengines/pogo_e02/pogo_e02.h > +++ /dev/null > @@ -1,29 +0,0 @@ > -/* SPDX-License-Identifier: GPL-2.0+ */ > -/* > - * Copyright (C) 2012 > - * David Purdy <david.c.purdy@gmail.com> > - * > - * Based on Kirkwood support: > - * (C) Copyright 2009 > - * Marvell Semiconductor <www.marvell.com> > - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> > - */ > - > -#ifndef __POGO_E02_H > -#define __POGO_E02_H > - > -/* GPIO configuration */ > -#define POGO_E02_OE_LOW (~(0)) > -#define POGO_E02_OE_HIGH (~(0)) > -#define POGO_E02_OE_VAL_LOW (1 << 29) > -#define POGO_E02_OE_VAL_HIGH 0 > - > -/* PHY related */ > -#define MV88E1116_LED_FCTRL_REG 10 > -#define MV88E1116_CPRSP_CR3_REG 21 > -#define MV88E1116_MAC_CTRL_REG 21 > -#define MV88E1116_PGADR_REG 22 > -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) > -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) > - > -#endif /* __POGO_E02_H */ > diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig > index 10f08a515d..7853cc7b24 100644 > --- a/configs/pogo_e02_defconfig > +++ b/configs/pogo_e02_defconfig > @@ -2,13 +2,14 @@ CONFIG_ARM=y > CONFIG_SKIP_LOWLEVEL_INIT=y > CONFIG_SYS_DCACHE_OFF=y > CONFIG_ARCH_CPU_INIT=y > +CONFIG_SYS_THUMB_BUILD=y > CONFIG_ARCH_KIRKWOOD=y > CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_e02/kwbimage.cfg" > CONFIG_SYS_TEXT_BASE=0x600000 > CONFIG_NR_DRAM_BANKS=2 > CONFIG_TARGET_POGO_E02=y > CONFIG_ENV_SIZE=0x20000 > -CONFIG_ENV_OFFSET=0x60000 > +CONFIG_ENV_OFFSET=0xC0000 > CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02" > CONFIG_IDENT_STRING="\nPogo E02" > # CONFIG_SYS_MALLOC_F is not set > @@ -36,11 +37,14 @@ CONFIG_OF_CONTROL=y > CONFIG_ENV_OVERWRITE=y > CONFIG_ENV_IS_IN_NAND=y > CONFIG_SYS_RELOC_GD_ENV_ADDR=y > +CONFIG_NET_RANDOM_ETHADDR=y > CONFIG_NETCONSOLE=y > CONFIG_DM=y > # CONFIG_MMC is not set > CONFIG_MTD=y > CONFIG_MTD_RAW_NAND=y > +CONFIG_PHY_MARVELL=y > +CONFIG_DM_ETH=y > CONFIG_MVGBE=y > CONFIG_MII=y > CONFIG_SYS_NS16550=y > diff --git a/include/configs/pogo_e02.h b/include/configs/pogo_e02.h > index 3e94125cb3..51c802f2b3 100644 > --- a/include/configs/pogo_e02.h > +++ b/include/configs/pogo_e02.h > @@ -14,10 +14,6 @@ > > #include "mv-common.h" > > -/* > - * Environment variables configurations > - */ > - > /* > * Default environment variables > */ > @@ -33,13 +29,10 @@ > /* > * Ethernet Driver configuration > */ > -#ifdef CONFIG_CMD_NET > #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ > #define CONFIG_PHY_BASE_ADR 0 > -#endif /* CONFIG_CMD_NET */ > - > -/* > - * File system > - */ > +#ifdef CONFIG_RESET_PHY_R > +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ > +#endif > > #endif /* _CONFIG_POGO_E02_H */ Viele Grüße, Stefan Roese
On 2/9/22 03:56, Tony Dinh wrote: > The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert > to Driver Model and use uclass mvgbe and the compatible driver M88E1118R > to bring up Ethernet. > > - Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL > to bring up Ethernet. > - Currently, CONFIG_RESET_PHY_R symbol is used in > arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood > boards with mv8831116 PHY, with each board defines the function > reset_phy(). Undefine it for this board. > - As the result of the migration to Driver Model, this u-boot image has > grown substantially (about 100K, give or take). The old envs location > at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K). > - Miscellaneous changes: Move constants to .c file and remove header file > board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to > keep u-boot image under 512K, use BIT macro, and cleanup comments. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> Applied to u-boot-marvell/master Thanks, Stefan > --- > > board/cloudengines/pogo_e02/pogo_e02.c | 51 +++++++------------------- > board/cloudengines/pogo_e02/pogo_e02.h | 29 --------------- > configs/pogo_e02_defconfig | 6 ++- > include/configs/pogo_e02.h | 13 ++----- > 4 files changed, 22 insertions(+), 77 deletions(-) > delete mode 100644 board/cloudengines/pogo_e02/pogo_e02.h > > diff --git a/board/cloudengines/pogo_e02/pogo_e02.c b/board/cloudengines/pogo_e02/pogo_e02.c > index 039fd6e3dd..59e1218b41 100644 > --- a/board/cloudengines/pogo_e02/pogo_e02.c > +++ b/board/cloudengines/pogo_e02/pogo_e02.c > @@ -1,5 +1,6 @@ > // SPDX-License-Identifier: GPL-2.0+ > /* > + * Copyright (C) 2022 Tony Dinh <mibodhi@gmail.com> > * Copyright (C) 2012 > * David Purdy <david.c.purdy@gmail.com> > * > @@ -12,16 +13,21 @@ > #include <common.h> > #include <init.h> > #include <log.h> > -#include <miiphy.h> > -#include <net.h> > +#include <netdev.h> > #include <asm/arch/cpu.h> > #include <asm/arch/soc.h> > #include <asm/arch/mpp.h> > #include <asm/global_data.h> > -#include "pogo_e02.h" > +#include <linux/bitops.h> > > DECLARE_GLOBAL_DATA_PTR; > > +/* GPIO configuration */ > +#define POGO_E02_OE_LOW (~(0)) > +#define POGO_E02_OE_HIGH (~(0)) > +#define POGO_E02_OE_VAL_LOW BIT(29) > +#define POGO_E02_OE_VAL_HIGH 0 > + > int board_early_init_f(void) > { > /* > @@ -64,6 +70,11 @@ int board_early_init_f(void) > return 0; > } > > +int board_eth_init(struct bd_info *bis) > +{ > + return cpu_eth_init(bis); > +} > + > int board_init(void) > { > /* Boot parameters address */ > @@ -71,37 +82,3 @@ int board_init(void) > > return 0; > } > - > -#ifdef CONFIG_RESET_PHY_R > -/* Configure and initialize PHY */ > -void reset_phy(void) > -{ > - u16 reg; > - u16 devadr; > - char *name = "egiga0"; > - > - if (miiphy_set_current_dev(name)) > - return; > - > - /* command to read PHY dev address */ > - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > - printf("Err..(%s) could not read PHY dev address\n", __func__); > - return; > - } > - > - /* > - * Enable RGMII delay on Tx and Rx for CPU port > - * Ref: sec 4.7.2 of chip datasheet > - */ > - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); > - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); > - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); > - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); > - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); > - > - /* reset the phy */ > - miiphy_reset(name, devadr); > - > - debug("88E1116 Initialized on %s\n", name); > -} > -#endif /* CONFIG_RESET_PHY_R */ > diff --git a/board/cloudengines/pogo_e02/pogo_e02.h b/board/cloudengines/pogo_e02/pogo_e02.h > deleted file mode 100644 > index c8397b4d4f..0000000000 > --- a/board/cloudengines/pogo_e02/pogo_e02.h > +++ /dev/null > @@ -1,29 +0,0 @@ > -/* SPDX-License-Identifier: GPL-2.0+ */ > -/* > - * Copyright (C) 2012 > - * David Purdy <david.c.purdy@gmail.com> > - * > - * Based on Kirkwood support: > - * (C) Copyright 2009 > - * Marvell Semiconductor <www.marvell.com> > - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> > - */ > - > -#ifndef __POGO_E02_H > -#define __POGO_E02_H > - > -/* GPIO configuration */ > -#define POGO_E02_OE_LOW (~(0)) > -#define POGO_E02_OE_HIGH (~(0)) > -#define POGO_E02_OE_VAL_LOW (1 << 29) > -#define POGO_E02_OE_VAL_HIGH 0 > - > -/* PHY related */ > -#define MV88E1116_LED_FCTRL_REG 10 > -#define MV88E1116_CPRSP_CR3_REG 21 > -#define MV88E1116_MAC_CTRL_REG 21 > -#define MV88E1116_PGADR_REG 22 > -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) > -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) > - > -#endif /* __POGO_E02_H */ > diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig > index 10f08a515d..7853cc7b24 100644 > --- a/configs/pogo_e02_defconfig > +++ b/configs/pogo_e02_defconfig > @@ -2,13 +2,14 @@ CONFIG_ARM=y > CONFIG_SKIP_LOWLEVEL_INIT=y > CONFIG_SYS_DCACHE_OFF=y > CONFIG_ARCH_CPU_INIT=y > +CONFIG_SYS_THUMB_BUILD=y > CONFIG_ARCH_KIRKWOOD=y > CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_e02/kwbimage.cfg" > CONFIG_SYS_TEXT_BASE=0x600000 > CONFIG_NR_DRAM_BANKS=2 > CONFIG_TARGET_POGO_E02=y > CONFIG_ENV_SIZE=0x20000 > -CONFIG_ENV_OFFSET=0x60000 > +CONFIG_ENV_OFFSET=0xC0000 > CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02" > CONFIG_IDENT_STRING="\nPogo E02" > # CONFIG_SYS_MALLOC_F is not set > @@ -36,11 +37,14 @@ CONFIG_OF_CONTROL=y > CONFIG_ENV_OVERWRITE=y > CONFIG_ENV_IS_IN_NAND=y > CONFIG_SYS_RELOC_GD_ENV_ADDR=y > +CONFIG_NET_RANDOM_ETHADDR=y > CONFIG_NETCONSOLE=y > CONFIG_DM=y > # CONFIG_MMC is not set > CONFIG_MTD=y > CONFIG_MTD_RAW_NAND=y > +CONFIG_PHY_MARVELL=y > +CONFIG_DM_ETH=y > CONFIG_MVGBE=y > CONFIG_MII=y > CONFIG_SYS_NS16550=y > diff --git a/include/configs/pogo_e02.h b/include/configs/pogo_e02.h > index 3e94125cb3..51c802f2b3 100644 > --- a/include/configs/pogo_e02.h > +++ b/include/configs/pogo_e02.h > @@ -14,10 +14,6 @@ > > #include "mv-common.h" > > -/* > - * Environment variables configurations > - */ > - > /* > * Default environment variables > */ > @@ -33,13 +29,10 @@ > /* > * Ethernet Driver configuration > */ > -#ifdef CONFIG_CMD_NET > #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ > #define CONFIG_PHY_BASE_ADR 0 > -#endif /* CONFIG_CMD_NET */ > - > -/* > - * File system > - */ > +#ifdef CONFIG_RESET_PHY_R > +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ > +#endif > > #endif /* _CONFIG_POGO_E02_H */ Viele Grüße, Stefan Roese
diff --git a/board/cloudengines/pogo_e02/pogo_e02.c b/board/cloudengines/pogo_e02/pogo_e02.c index 039fd6e3dd..59e1218b41 100644 --- a/board/cloudengines/pogo_e02/pogo_e02.c +++ b/board/cloudengines/pogo_e02/pogo_e02.c @@ -1,5 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /* + * Copyright (C) 2022 Tony Dinh <mibodhi@gmail.com> * Copyright (C) 2012 * David Purdy <david.c.purdy@gmail.com> * @@ -12,16 +13,21 @@ #include <common.h> #include <init.h> #include <log.h> -#include <miiphy.h> -#include <net.h> +#include <netdev.h> #include <asm/arch/cpu.h> #include <asm/arch/soc.h> #include <asm/arch/mpp.h> #include <asm/global_data.h> -#include "pogo_e02.h" +#include <linux/bitops.h> DECLARE_GLOBAL_DATA_PTR; +/* GPIO configuration */ +#define POGO_E02_OE_LOW (~(0)) +#define POGO_E02_OE_HIGH (~(0)) +#define POGO_E02_OE_VAL_LOW BIT(29) +#define POGO_E02_OE_VAL_HIGH 0 + int board_early_init_f(void) { /* @@ -64,6 +70,11 @@ int board_early_init_f(void) return 0; } +int board_eth_init(struct bd_info *bis) +{ + return cpu_eth_init(bis); +} + int board_init(void) { /* Boot parameters address */ @@ -71,37 +82,3 @@ int board_init(void) return 0; } - -#ifdef CONFIG_RESET_PHY_R -/* Configure and initialize PHY */ -void reset_phy(void) -{ - u16 reg; - u16 devadr; - char *name = "egiga0"; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..(%s) could not read PHY dev address\n", __func__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - debug("88E1116 Initialized on %s\n", name); -} -#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/cloudengines/pogo_e02/pogo_e02.h b/board/cloudengines/pogo_e02/pogo_e02.h deleted file mode 100644 index c8397b4d4f..0000000000 --- a/board/cloudengines/pogo_e02/pogo_e02.h +++ /dev/null @@ -1,29 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 - * David Purdy <david.c.purdy@gmail.com> - * - * Based on Kirkwood support: - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - */ - -#ifndef __POGO_E02_H -#define __POGO_E02_H - -/* GPIO configuration */ -#define POGO_E02_OE_LOW (~(0)) -#define POGO_E02_OE_HIGH (~(0)) -#define POGO_E02_OE_VAL_LOW (1 << 29) -#define POGO_E02_OE_VAL_HIGH 0 - -/* PHY related */ -#define MV88E1116_LED_FCTRL_REG 10 -#define MV88E1116_CPRSP_CR3_REG 21 -#define MV88E1116_MAC_CTRL_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __POGO_E02_H */ diff --git a/configs/pogo_e02_defconfig b/configs/pogo_e02_defconfig index 10f08a515d..7853cc7b24 100644 --- a/configs/pogo_e02_defconfig +++ b/configs/pogo_e02_defconfig @@ -2,13 +2,14 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_SYS_DCACHE_OFF=y CONFIG_ARCH_CPU_INIT=y +CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_KIRKWOOD=y CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_e02/kwbimage.cfg" CONFIG_SYS_TEXT_BASE=0x600000 CONFIG_NR_DRAM_BANKS=2 CONFIG_TARGET_POGO_E02=y CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_OFFSET=0x60000 +CONFIG_ENV_OFFSET=0xC0000 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02" CONFIG_IDENT_STRING="\nPogo E02" # CONFIG_SYS_MALLOC_F is not set @@ -36,11 +37,14 @@ CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_NAND=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_NETCONSOLE=y CONFIG_DM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_MARVELL=y +CONFIG_DM_ETH=y CONFIG_MVGBE=y CONFIG_MII=y CONFIG_SYS_NS16550=y diff --git a/include/configs/pogo_e02.h b/include/configs/pogo_e02.h index 3e94125cb3..51c802f2b3 100644 --- a/include/configs/pogo_e02.h +++ b/include/configs/pogo_e02.h @@ -14,10 +14,6 @@ #include "mv-common.h" -/* - * Environment variables configurations - */ - /* * Default environment variables */ @@ -33,13 +29,10 @@ /* * Ethernet Driver configuration */ -#ifdef CONFIG_CMD_NET #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ - -/* - * File system - */ +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */ +#endif #endif /* _CONFIG_POGO_E02_H */
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert to Driver Model and use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet. - Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL to bring up Ethernet. - Currently, CONFIG_RESET_PHY_R symbol is used in arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood boards with mv8831116 PHY, with each board defines the function reset_phy(). Undefine it for this board. - As the result of the migration to Driver Model, this u-boot image has grown substantially (about 100K, give or take). The old envs location at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K). - Miscellaneous changes: Move constants to .c file and remove header file board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to keep u-boot image under 512K, use BIT macro, and cleanup comments. Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- board/cloudengines/pogo_e02/pogo_e02.c | 51 +++++++------------------- board/cloudengines/pogo_e02/pogo_e02.h | 29 --------------- configs/pogo_e02_defconfig | 6 ++- include/configs/pogo_e02.h | 13 ++----- 4 files changed, 22 insertions(+), 77 deletions(-) delete mode 100644 board/cloudengines/pogo_e02/pogo_e02.h