new file mode 100644
@@ -0,0 +1,481 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ * Copyright 2021 Purism
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/imx8mq_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clock.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <power/pmic.h>
+#include <power/bd71837.h>
+#include <hang.h>
+#include <init.h>
+#include <spl.h>
+#include <usb.h>
+#include <dwc3-uboot.h>
+#include <linux/delay.h>
+#include "librem5.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void spl_dram_init(void)
+{
+ /* ddr init */
+ if ((get_cpu_rev() & 0xfff) == CHIP_REV_2_1)
+ ddr_init(&dram_timing);
+ else
+ ddr_init(&dram_timing_b0);
+}
+
+int spl_board_boot_device(enum boot_device boot_dev_spl)
+{
+ log_debug("%s : starting\n", __func__);
+
+ switch (boot_dev_spl) {
+ case SD1_BOOT:
+ case MMC1_BOOT:
+ return BOOT_DEVICE_MMC1;
+ case USB_BOOT:
+ return BOOT_DEVICE_BOARD;
+ default:
+ return BOOT_DEVICE_NONE;
+ }
+}
+
+#define I2C_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_ODE | PAD_CTL_DSE7 | PAD_CTL_FSEL3)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = IMX8MQ_PAD_I2C1_SCL__I2C1_SCL | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 | PC,
+ .gp = IMX_GPIO_NR(5, 14),
+ },
+ .sda = {
+ .i2c_mode = IMX8MQ_PAD_I2C1_SDA__I2C1_SDA | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 | PC,
+ .gp = IMX_GPIO_NR(5, 15),
+ },
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = IMX8MQ_PAD_I2C2_SCL__I2C2_SCL | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C2_SCL__GPIO5_IO16 | PC,
+ .gp = IMX_GPIO_NR(5, 16),
+ },
+ .sda = {
+ .i2c_mode = IMX8MQ_PAD_I2C2_SDA__I2C2_SDA | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C2_SDA__GPIO5_IO17 | PC,
+ .gp = IMX_GPIO_NR(5, 17),
+ },
+};
+
+struct i2c_pads_info i2c_pad_info3 = {
+ .scl = {
+ .i2c_mode = IMX8MQ_PAD_I2C3_SCL__I2C3_SCL | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C3_SCL__GPIO5_IO18 | PC,
+ .gp = IMX_GPIO_NR(5, 18),
+ },
+ .sda = {
+ .i2c_mode = IMX8MQ_PAD_I2C3_SDA__I2C3_SDA | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C3_SDA__GPIO5_IO19 | PC,
+ .gp = IMX_GPIO_NR(5, 19),
+ },
+};
+
+struct i2c_pads_info i2c_pad_info4 = {
+ .scl = {
+ .i2c_mode = IMX8MQ_PAD_I2C4_SCL__I2C4_SCL | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C4_SCL__GPIO5_IO20 | PC,
+ .gp = IMX_GPIO_NR(5, 20),
+ },
+ .sda = {
+ .i2c_mode = IMX8MQ_PAD_I2C4_SDA__I2C4_SDA | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C4_SDA__GPIO5_IO21 | PC,
+ .gp = IMX_GPIO_NR(5, 21),
+ },
+};
+
+#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+
+static const iomux_v3_cfg_t uart_pads[] = {
+ IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART2_RXD__UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART2_TXD__UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART3_RXD__UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART3_TXD__UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_ECSPI2_SCLK__UART4_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_ECSPI2_MOSI__UART4_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10)
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = 1;
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = 1;
+ break;
+ }
+
+ return ret;
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \
+ PAD_CTL_FSEL1)
+#define USDHC_GPIO_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_DSE1)
+
+static const iomux_v3_cfg_t usdhc1_pads[] = {
+ IMX8MQ_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static const iomux_v3_cfg_t usdhc2_pads[] = {
+ IMX8MQ_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+ IMX8MQ_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+ IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+ IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+ IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0x16 */
+ IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+ IMX8MQ_PAD_SD2_RESET_B__GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC1_BASE_ADDR, 0, 8},
+#ifndef CONFIG_SPL_BUILD
+ {USDHC2_BASE_ADDR, 0, 4},
+#endif
+};
+
+int board_mmc_init(struct bd_info *bis)
+{
+ int i, ret;
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 USDHC1
+ * mmc1 USDHC2
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ log_debug("Initializing FSL USDHC port %d\n", i);
+ switch (i) {
+ case 0:
+ init_clk_usdhc(0);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(USDHC1_CLK_ROOT);
+ imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
+ ARRAY_SIZE(usdhc1_pads));
+ gpio_request(USDHC1_PWR_GPIO, "usdhc1_reset");
+ gpio_direction_output(USDHC1_PWR_GPIO, 0);
+ udelay(500);
+ gpio_direction_output(USDHC1_PWR_GPIO, 1);
+ break;
+ case 1:
+ init_clk_usdhc(1);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(USDHC2_CLK_ROOT);
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
+ ARRAY_SIZE(usdhc2_pads));
+ gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
+ gpio_direction_output(USDHC2_PWR_GPIO, 0);
+ udelay(500);
+ gpio_direction_output(USDHC2_PWR_GPIO, 1);
+ break;
+ default:
+ log_err("Warning: USDHC controller(%d) not supported\n", i + 1);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+#define LDO_VOLT_EN BIT(6)
+
+/*
+ * Disable the charger - it will be re-enabled in u-boot
+ */
+void disable_charger_bq25896(void)
+{
+ u8 val;
+ int timeout = 1000; // ms
+
+ /* Set the i2c bus */
+ i2c_set_bus_num(3);
+
+ /* disable ship mode if BATFET_DLY is set */
+ val = i2c_reg_read(0x6a, 0x09);
+ log_debug("REG09 0x%x\n", val);
+ if (val & 0x28) {
+ val = val & ~0x28;
+ i2c_reg_write(0x6a, 0x09, val);
+ }
+
+ /* disable and trigger DPDM, ICO, HVDCP and MaxCharge */
+ val = i2c_reg_read(0x6a, 0x02);
+ log_debug("REG02 0x%x\n", val);
+ val &= 0xe0;
+ i2c_reg_write(0x6a, 0x02, val);
+
+ /* disable charger and enable BAT_LOADEN */
+ val = i2c_reg_read(0x6a, 0x03);
+ log_debug("REG03 0x%x\n", val);
+ val = (val | 0x80) & ~0x10;
+ i2c_reg_write(0x6a, 0x03, val);
+
+ mdelay(10);
+
+ /* force ADC conversions */
+ val = i2c_reg_read(0x6a, 0x02);
+ log_debug("REG02 0x%x\n", val);
+ val = (val | 0x80) & ~0x40;
+ i2c_reg_write(0x6a, 0x02, val);
+
+ do {
+ mdelay(10);
+ timeout -= 10;
+ } while ((i2c_reg_read(0x6a, 0x02) & 0x80) && (timeout > 0));
+
+ /* enable STAT pin */
+ val = i2c_reg_read(0x6a, 0x07);
+ log_debug("REG07 0x%x\n", val);
+ val = val & ~0x40;
+ i2c_reg_write(0x6a, 0x07, val);
+
+ /* check VBUS */
+ val = i2c_reg_read(0x6a, 0x11);
+ log_debug("VBUS good %d\n", (val >> 7) & 1);
+ log_debug("VBUS mV %d\n", (val & 0x7f) * 100 + 2600);
+
+ /* check VBAT */
+ val = i2c_reg_read(0x6a, 0x0e);
+ log_debug("VBAT mV %d\n", (val & 0x7f) * 20 + 2304);
+
+ /* limit the VINDPM to 3.9V */
+ i2c_reg_write(0x6a, 0x0d, 0x8d);
+
+ /* set the max voltage to 4.192V */
+ val = i2c_reg_read(0x6a, 0x6);
+ val = (val & ~0xFC) | 0x16 << 2;
+ i2c_reg_write(0x6a, 0x6, val);
+
+ /* set the SYS_MIN to 3.7V */
+ val = i2c_reg_read(0x6a, 0x3);
+ val = val | 0xE;
+ i2c_reg_write(0x6a, 0x3, val);
+
+ /* disable BAT_LOADEN */
+ val = i2c_reg_read(0x6a, 0x03);
+ log_debug("REG03 0x%x\n", val);
+ val = val & ~0x80;
+ i2c_reg_write(0x6a, 0x03, val);
+}
+
+#define I2C_PMIC 0
+
+int power_bd71837_init(unsigned char bus)
+{
+ static const char name[] = BD718XX_REGULATOR_DRIVER;
+ struct pmic *p = pmic_alloc();
+
+ if (!p) {
+ log_err("%s: POWER allocation error!\n", __func__);
+ return -ENOMEM;
+ }
+
+ p->name = name;
+ p->interface = I2C_PMIC;
+ p->number_of_regs = BD718XX_MAX_REGISTER;
+ p->hw.i2c.addr = CONFIG_POWER_BD71837_I2C_ADDR;
+ p->hw.i2c.tx_num = 1;
+ p->bus = bus;
+
+ return 0;
+}
+
+int power_init_board(void)
+{
+ struct pmic *p;
+ int ldo[] = {BD718XX_LDO5_VOLT, BD718XX_LDO6_VOLT,
+ BD71837_LDO7_VOLT};
+ u32 val;
+ int i, rv;
+
+ /* Set the i2c bus */
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+ /*
+ * Init PMIC
+ */
+ rv = power_bd71837_init(CONFIG_POWER_BD71837_I2C_BUS);
+ if (rv) {
+ log_err("%s: power_bd71837_init(%d) error %d\n", __func__,
+ CONFIG_POWER_BD71837_I2C_BUS, rv);
+ goto out;
+ }
+
+ p = pmic_get(BD718XX_REGULATOR_DRIVER);
+ if (!p) {
+ log_err("%s: pmic_get(%s) failed\n", __func__, BD718XX_REGULATOR_DRIVER);
+ rv = -ENODEV;
+ goto out;
+ }
+
+ rv = pmic_probe(p);
+ if (rv) {
+ log_err("%s: pmic_probe() error %d\n", __func__, rv);
+ goto out;
+ }
+
+ /*
+ * Unlock all regs
+ */
+ pmic_reg_write(p, BD718XX_REGLOCK, 0);
+
+ /* find the reset cause */
+ pmic_reg_read(p, 0x29, &val);
+ log_debug("%s: reset cause %d\n", __func__, val);
+
+ /*
+ * Reconfigure default voltages and disable:
+ * - BUCK3: VDD_GPU_0V9 (1.00 -> 0.90)
+ * - BUCK4: VDD_VPU_0V9 (1.00 -> 0.90)
+ */
+ pmic_reg_write(p, BD71837_BUCK3_VOLT_RUN, 0x14);
+ pmic_reg_write(p, BD71837_BUCK4_VOLT_RUN, 0x14);
+
+ /*
+ * Enable PHYs voltages: LDO5-7
+ */
+ for (i = 0; i < ARRAY_SIZE(ldo); i++) {
+ rv = pmic_reg_read(p, ldo[i], &val);
+ if (rv) {
+ log_err("%s: pmic_read(%x) error %d\n", __func__,
+ ldo[i], rv);
+ continue;
+ }
+
+ pmic_reg_write(p, ldo[i], val | LDO_VOLT_EN);
+ }
+
+ udelay(500);
+
+ rv = 0;
+out:
+ return rv;
+}
+
+void spl_board_init(void)
+{
+ init_usb_clk();
+
+ if (is_usb_boot())
+ puts("USB Boot\n");
+ else
+ puts("Normal Boot\n");
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ if (is_usb_boot())
+ spl_boot_list[0] = BOOT_DEVICE_BOARD;
+ else
+ spl_boot_list[0] = BOOT_DEVICE_MMC1;
+}
+
+int board_fit_config_name_match(const char *name)
+{
+ /* Just empty function now - can't decide what to choose */
+ return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+ int ret;
+
+ /* Clear global data */
+ memset((void *)gd, 0, sizeof(gd_t));
+
+ arch_cpu_init();
+
+ init_uart_clk(CONSOLE_UART_CLK);
+ imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+
+#ifdef CONSOLE_ON_UART4
+ gpio_request(WIFI_EN, "WIFI_EN");
+ gpio_direction_output(WIFI_EN, 1);
+#endif
+
+ board_early_init_f();
+
+ timer_init();
+
+ preloader_console_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ ret = spl_init();
+ if (ret) {
+ log_err("spl_init() failed: %d\n", ret);
+ hang();
+ }
+
+ enable_tzc380();
+
+ printf("Initializing pinmux\n");
+ init_pinmux();
+ gpio_direction_output(LED_G, 1);
+ gpio_direction_output(MOTO, 1);
+ mdelay(50);
+ gpio_direction_output(MOTO, 0);
+
+ /* Enable and configure i2c buses not used below */
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+ setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+
+ power_init_board();
+
+ disable_charger_bq25896();
+
+ /* initialize this for M4 even if u-boot doesn't have SF_CMD */
+ printf("Initializing ECSPI\n");
+ board_ecspi_init();
+
+ /* DDR initialization */
+ printf("Initializing DRAM\n");
+ spl_dram_init();
+}
+