| Message ID | 20201021095708.162820-1-andrej.rosano@f-secure.com |
|---|---|
| State | Changes Requested |
| Delegated to: | Stefano Babic |
| Headers | show |
| Series | ARM: mx6: add support for USB armory Mk II board | expand |
Hi Andrej, On 21.10.20 11:57, andrej.rosano@f-secure.com wrote: > From: Andrej Rosano <andrej.rosano@f-secure.com> > > Add support for F-Secure USB armory Mk II board, an open source > flash-drive sized computer based on Freescale i.MX6UL SoC. > > http://inversepath.com/usbarmory > > Signed-off-by: Andrej Rosano <andrej@inversepath.com> > Cc: Stefano Babic <sbabic@denx.de> > --- > arch/arm/dts/Makefile | 1 + > arch/arm/dts/imx6ull-usbarmory.dts | 200 ++++++++++ > arch/arm/mach-imx/mx6/Kconfig | 5 + > board/inversepath/usbarmory-mark-two/Kconfig | 71 ++++ > .../usbarmory-mark-two/MAINTAINERS | 6 + > board/inversepath/usbarmory-mark-two/Makefile | 10 + > .../usbarmory-mark-two/imximage-1gb.cfg | 87 +++++ > .../usbarmory-mark-two/imximage-512mb.cfg | 89 +++++ > .../usbarmory-mark-two/usbarmory-mark-two.c | 347 ++++++++++++++++++ > configs/usbarmory-mark-two_defconfig | 72 ++++ > include/configs/usbarmory-mark-two.h | 234 ++++++++++++ > 11 files changed, 1122 insertions(+) > create mode 100644 arch/arm/dts/imx6ull-usbarmory.dts > create mode 100644 board/inversepath/usbarmory-mark-two/Kconfig > create mode 100644 board/inversepath/usbarmory-mark-two/MAINTAINERS > create mode 100644 board/inversepath/usbarmory-mark-two/Makefile > create mode 100644 board/inversepath/usbarmory-mark-two/imximage-1gb.cfg > create mode 100644 board/inversepath/usbarmory-mark-two/imximage-512mb.cfg Just that you need two files to setup the RAM controller is a good reason to switch to SPL. > create mode 100644 board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c > create mode 100644 configs/usbarmory-mark-two_defconfig > create mode 100644 include/configs/usbarmory-mark-two.h > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index b195723f16..d17c14c9bb 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -731,6 +731,7 @@ dtb-$(CONFIG_MX6ULL) += \ > imx6ull-myir-mys-6ulx-eval.dtb \ > imx6ull-phytec-segin-ff-rdk-emmc.dtb \ > imx6ull-dart-6ul.dtb \ > + imx6ull-usbarmory.dtb \ > imx6ull-somlabs-visionsom.dtb \ > imx6ulz-14x14-evk.dtb > > diff --git a/arch/arm/dts/imx6ull-usbarmory.dts b/arch/arm/dts/imx6ull-usbarmory.dts > new file mode 100644 > index 0000000000..d5a616f703 > --- /dev/null > +++ b/arch/arm/dts/imx6ull-usbarmory.dts > @@ -0,0 +1,200 @@ > +/* > + * USB armory Mk II device tree file > + * https://github.com/inversepath/usbarmory > + * > + * Copyright (C) 2019, F-Secure Corporation > + * Andrej Rosano <andrej.rosano@f-secure.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > + > +#include "imx6ull.dtsi" > + > +/ { > + model = "F-Secure USB armory Mk II"; > + compatible = "inversepath,imx6ull-usbarmory-mkII", "fsl,imx6ull"; > + > + chosen { > + stdout-path = &uart2; > + }; > + > + memory { > + reg = <0x80000000 0x20000000>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_led>; > + > + led-white { > + label = "LED_WHITE"; > + gpios = <&gpio4 21 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + led-blue { > + label = "LED_BLUE"; > + gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg_sd1_vmmc: sd1_regulator { > + compatible = "regulator-fixed"; > + regulator-name = "VSD_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + }; > +}; > + > +&cpu0 { > + operating-points = < > + /* kHz uV */ > + 900000 1275000 > + 792000 1225000 > + 528000 1175000 > + 396000 1025000 > + 198000 950000 > + >; > + fsl,soc-operating-points = < > + /* KHz uV */ > + 900000 1250000 > + 792000 1175000 > + 528000 1175000 > + 396000 1175000 > + 198000 1175000 > + >; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_bluetooth>; > + uart-has-rtscts; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + no-1-8-v; > + keep-power-in-suspend; > + wakeup-source; > + non-removable; // FIXME: CD works on i.MX6ULL but not i.MX6ULZ > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + non-removable; > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 > + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 > + >; > + }; > + > + pinctrl_bluetooth: uart1grp { > + fsl,pins = < > + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b0 /* BT_UART_TX */ > + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b0 /* BT_UART_RX */ > + MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x1b0b0 /* BT_UART_CTS */ > + MX6UL_PAD_GPIO1_IO07__UART1_DCE_RTS 0x1b0b0 /* BT_UART_RTS */ > + MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24 0x1f020 /* BT_UART_DSR */ > + MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25 0x1f020 /* BT_UART_DTR */ > + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1f020 /* BT_SWDCLK */ > + MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1f020 /* BT_SWDIO */ > + MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x1f020 /* BT_RESET */ > + MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x1f020 /* BT_SWITCH_1 */ > + MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1f020 /* BT_SWITCH_2 */ > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO02__I2C1_SCL 0x4001b8b0 > + MX6UL_PAD_GPIO1_IO03__I2C1_SDA 0x4001b8b0 > + >; > + }; > + > + pinctrl_led: ledgrp { > + fsl,pins = < > + MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x1f020 > + MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x1f020 > + >; > + }; > +}; > + > +&usbotg1 { > + dr_mode = "peripheral"; > + disable-over-current; > + tpl-support; > + status = "okay"; > +}; > + > +&usbotg2 { > + dr_mode = "host"; > + disable-over-current; > + tpl-support; > + status = "okay"; > +}; > diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig > index 3d72517fa1..36b5d46c4b 100644 > --- a/arch/arm/mach-imx/mx6/Kconfig > +++ b/arch/arm/mach-imx/mx6/Kconfig > @@ -644,6 +644,10 @@ config TARGET_UDOO_NEO > select SUPPORT_SPL > imply CMD_DM > > +config TARGET_USBARMORY_MARK_TWO > + bool "Support USB armory Mk II" > + depends on MX6ULL > + > config TARGET_SOFTING_VINING_2000 > bool "Softing VIN|ING 2000" > depends on MX6SX > @@ -744,6 +748,7 @@ source "board/phytec/pcm058/Kconfig" > source "board/phytec/pfla02/Kconfig" > source "board/phytec/pcl063/Kconfig" > source "board/gateworks/gw_ventana/Kconfig" > +source "board/inversepath/usbarmory-mark-two/Kconfig" > source "board/kosagi/novena/Kconfig" > source "board/softing/vining_2000/Kconfig" > source "board/liebherr/display5/Kconfig" > diff --git a/board/inversepath/usbarmory-mark-two/Kconfig b/board/inversepath/usbarmory-mark-two/Kconfig > new file mode 100644 > index 0000000000..e13290b9a1 > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/Kconfig > @@ -0,0 +1,71 @@ > +if TARGET_USBARMORY_MARK_TWO > + > +choice > + prompt "DDR size" > + default SYS_DDR_512MB > + > +config SYS_DDR_512MB > + bool "512 MB" > + > +config SYS_DDR_1GB > + bool "1 GB" > + > +endchoice > + > +choice > + prompt "Boot device" > + default SYS_BOOT_DEV_MICROSD > + > +config SYS_BOOT_DEV_MICROSD > + bool "micro SD" > + > +config SYS_BOOT_DEV_EMMC > + bool "eMMC" > + > +endchoice > + > +choice > + prompt "Boot mode" > + default SYS_BOOT_MODE_NORMAL > + > +config SYS_BOOT_MODE_NORMAL > + select DISTRO_DEFAULTS > + select ENV_IS_IN_MMC > + bool "Normal" > + > +config SYS_BOOT_MODE_UMS > + bool "UMS" > + select ENV_IS_NOWHERE > + > +config SYS_BOOT_MODE_TFTP > + bool "TFTP" > + select ENV_IS_NOWHERE > + > +config SYS_BOOT_MODE_VERIFIED_OPEN > + bool "Verified Boot" > + select ENV_IS_NOWHERE > + > +config SYS_BOOT_MODE_VERIFIED_LOCKED > + bool "Verified Boot and console disabled" > + select ENV_IS_NOWHERE > + > +endchoice > + > +config IMX_CONFIG > + default "board/inversepath/usbarmory-mark-two/imximage-512mb.cfg" if SYS_DDR_512MB > + default "board/inversepath/usbarmory-mark-two/imximage-1gb.cfg" if SYS_DDR_1GB > + > +config SYS_MEMTEST_END > + default 0xa0000000 if SYS_DDR_512MB > + default 0xc0000000 if SYS_DDR_1G > + > +config SYS_BOARD > + default "usbarmory-mark-two" > + > +config SYS_VENDOR > + default "inversepath" > + > +config SYS_CONFIG_NAME > + default "usbarmory-mark-two" > + > +endif > diff --git a/board/inversepath/usbarmory-mark-two/MAINTAINERS b/board/inversepath/usbarmory-mark-two/MAINTAINERS > new file mode 100644 > index 0000000000..89b68ae866 > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/MAINTAINERS > @@ -0,0 +1,6 @@ > +USBARMORY MK II BOARD > +M: Andrej Rosano <andrej.rosano@f-secure.com> > +S: Maintained > +F: board/inversepath/usbarmory-mark-two/ > +F: include/configs/usbarmory-mark-two.h > +F: configs/usbarmory-mark-two_defconfig > diff --git a/board/inversepath/usbarmory-mark-two/Makefile b/board/inversepath/usbarmory-mark-two/Makefile > new file mode 100644 > index 0000000000..bf84d05bfd > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/Makefile > @@ -0,0 +1,10 @@ > +# > +# USB armory Mk II board Makefile > +# https://github.com/inversepath/usbarmory > +# > +# Copyright (C) 2019, F-Secure > +# Andrej Rosano <andrej.rosano@f-secure.com> > +# > +# SPDX-License-Identifier:|____GPL-2.0+ > + > +obj-y := usbarmory-mark-two.o > diff --git a/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg b/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg > new file mode 100644 > index 0000000000..47bd4830f7 > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg > @@ -0,0 +1,87 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * USB armory Mk II board imximage configuration > + * https://github.com/inversepath/usbarmory > + * > + * Copyright (C) 2019, F-Secure Corportation > + * Andrej Rosano <andrej.rosano@f-secure.com> > + */ > + > +#define __ASSEMBLY__ > +#include <config.h> > + > +IMAGE_VERSION 2 > +BOOT_FROM sd > +CSF CONFIG_CSF_SIZE > + > +/* CCM */ > + > +DATA 4 0x020c4068 0xffffffff /* CCM_CCGR0 */ > +DATA 4 0x020c406c 0xffffffff /* CCM_CCGR1 */ > +DATA 4 0x020c4070 0xffffffff /* CCM_CCGR2 */ > +DATA 4 0x020c4074 0xffffffff /* CCM_CCGR3 */ > +DATA 4 0x020c4078 0xffffffff /* CCM_CCGR4 */ > +DATA 4 0x020c407c 0xffffffff /* CCM_CCGR5 */ > +DATA 4 0x020c4080 0xffffffff /* CCM_CCGR6 */ > + > +/* IOMUX */ > + > +DATA 4 0x020E04B4 0x000C0000 /* GRP_DDR_TYPE */ > +DATA 4 0x020E04AC 0x00000000 /* GRP_DDRPKE */ > +DATA 4 0x020E027C 0x00000030 /* DRAM_SDCLK0_P */ > +DATA 4 0x020E0250 0x00000030 /* DRAM_CAS_B */ > +DATA 4 0x020E024C 0x00000030 /* DRAM_RAS_B */ > +DATA 4 0x020E0490 0x00000030 /* GRP_ADDDS */ > +DATA 4 0x020E0288 0x00000030 /* DRAM_RESET */ > +DATA 4 0x020E0270 0x00000000 /* DRAM_SDBA2 */ > +DATA 4 0x020E0260 0x00000030 /* DRAM_ODT0 */ > +DATA 4 0x020E0264 0x00000030 /* DRAM_ODT1 */ > +DATA 4 0x020E04A0 0x00000030 /* GRP_CTLDS */ > +DATA 4 0x020E0494 0x00020000 /* GRP_DDRMODE_CTL */ > +DATA 4 0x020E0280 0x00000030 /* DRAM_SDQS0_P */ > +DATA 4 0x020E0284 0x00000030 /* DRAM_SDQS1_P */ > +DATA 4 0x020E04B0 0x00020000 /* GRP_DDRMODE */ > +DATA 4 0x020E0498 0x00000030 /* GRP_B0DS */ > +DATA 4 0x020E04A4 0x00000030 /* GRP_B1DS */ > +DATA 4 0x020E0244 0x00000030 /* DRAM_DQM0 */ > +DATA 4 0x020E0248 0x00000030 /* DRAM_DQM1 */ > + > +/* MMDC */ > + > +DATA 4 0x021B001C 0x00008000 /* MMDC_MDSCR */ > +DATA 4 0x021B000C 0x676B52F3 /* MMDC_MDCFG0 */ > +DATA 4 0x021B0010 0xB66D0B63 /* MMDC_MDCFG1 */ > +DATA 4 0x021B0014 0x01FF00DB /* MMDC_MDCFG2 */ > +DATA 4 0x021B0008 0x1B333030 /* MMDC_MDOTC */ > +DATA 4 0x021B0018 0x00201740 /* MMDC_MDMISC */ > +DATA 4 0x021B002C 0x000026D2 /* MMDC_MDRWD */ > +DATA 4 0x021B0040 0x0000005F /* MMDC_MDASP */ > +DATA 4 0x021B0030 0x006B1023 /* MMDC_MDOR */ > +DATA 4 0x021B0000 0x85180000 /* MMDC_MDCTL */ > + > +/* Calibration */ > +DATA 4 0x021B0800 0xA1390003 /* MMDC_MPZQHWCTRL */ > +DATA 4 0x021B080C 0x00100014 /* MMDC_MPWLDECTRL0 */ > +DATA 4 0x021B083C 0x415C015C /* MMDC_MPDGCTRL0 */ > +DATA 4 0x021B0848 0x40403A40 /* MMDC_MPRDDLCTL */ > +DATA 4 0x021B0850 0x40402626 /* MMDC_MPWRDLCTL */ > +DATA 4 0x021B081C 0x33333333 /* MMDC_MPRDDQBY0DL */ > +DATA 4 0x021B0820 0x33333333 /* MMDC_MPRDDQBY1DL */ > +DATA 4 0x021B082C 0xf3333333 /* MMDC_MPWRDQBY0DL */ > +DATA 4 0x021B0830 0xf3333333 /* MMDC_MPWRDQBY1DL */ > +DATA 4 0x021B08C0 0x00921012 /* MMDC_MPDCCR */ > +DATA 4 0x021B08B8 0x00000800 /* MMDC_MPMUR0 */ > + > +/* JEDEC initialization sequence */ > +DATA 4 0x021B001C 0x02008032 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x00008033 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x00048031 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x15208030 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x04008040 /* MMDC_MDSCR */ > + > +DATA 4 0x021B0004 0x0002556D /* MMDC_MDPDC */ > +DATA 4 0x021B0404 0x00011006 /* MMDC_MAPSR */ > +DATA 4 0x021B0020 0x00000800 /* MMDC_MDREF */ > +DATA 4 0x021B0818 0x00000227 /* MMDC_MPODTCTRL */ > + > +DATA 4 0x021B001C 0x00000000 /* MMDC_MDSCR */ > diff --git a/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg b/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg > new file mode 100644 > index 0000000000..b856481b08 > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg > @@ -0,0 +1,89 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * USB armory Mk II board imximage configuration > + * https://github.com/inversepath/usbarmory > + * > + * Copyright (C) 2019, F-Secure Corportation > + * Andrej Rosano <andrej.rosano@f-secure.com> > + */ > + > +#define __ASSEMBLY__ > +#include <config.h> > + > +IMAGE_VERSION 2 > +BOOT_FROM sd > +CSF CONFIG_CSF_SIZE > + > +/* CCM */ > + > +DATA 4 0x020c4068 0xffffffff /* CCM_CCGR0 */ > +DATA 4 0x020c406c 0xffffffff /* CCM_CCGR1 */ > +DATA 4 0x020c4070 0xffffffff /* CCM_CCGR2 */ > +DATA 4 0x020c4074 0xffffffff /* CCM_CCGR3 */ > +DATA 4 0x020c4078 0xffffffff /* CCM_CCGR4 */ > +DATA 4 0x020c407c 0xffffffff /* CCM_CCGR5 */ > +DATA 4 0x020c4080 0xffffffff /* CCM_CCGR6 */ > + > +/* IOMUX */ > + > +DATA 4 0x020E04B4 0x000C0000 /* GRP_DDR_TYPE */ > +DATA 4 0x020E04AC 0x00000000 /* GRP_DDRPKE */ > +DATA 4 0x020E027C 0x00000030 /* DRAM_SDCLK0_P */ > +DATA 4 0x020E0250 0x00000030 /* DRAM_CAS_B */ > +DATA 4 0x020E024C 0x00000030 /* DRAM_RAS_B */ > +DATA 4 0x020E0490 0x00000030 /* GRP_ADDDS */ > +DATA 4 0x020E0288 0x00000030 /* DRAM_RESET */ > +DATA 4 0x020E0270 0x00000000 /* DRAM_SDBA2 */ > +DATA 4 0x020E0260 0x00000030 /* DRAM_ODT0 */ > +DATA 4 0x020E0264 0x00000030 /* DRAM_ODT1 */ > +DATA 4 0x020E04A0 0x00000030 /* GRP_CTLDS */ > +DATA 4 0x020E0494 0x00020000 /* GRP_DDRMODE_CTL */ > +DATA 4 0x020E0280 0x00000030 /* DRAM_SDQS0_P */ > +DATA 4 0x020E0284 0x00000030 /* DRAM_SDQS1_P */ > +DATA 4 0x020E04B0 0x00020000 /* GRP_DDRMODE */ > +DATA 4 0x020E0498 0x00000030 /* GRP_B0DS */ > +DATA 4 0x020E04A4 0x00000030 /* GRP_B1DS */ > +DATA 4 0x020E0244 0x00000030 /* DRAM_DQM0 */ > +DATA 4 0x020E0248 0x00000030 /* DRAM_DQM1 */ > + > +/* MMDC */ > + > +DATA 4 0x021B001C 0x00008000 /* MMDC_MDSCR */ > +DATA 4 0x021B000C 0x676B52F3 /* MMDC_MDCFG0 */ > +DATA 4 0x021B0010 0xB66D0B63 /* MMDC_MDCFG1 */ > +DATA 4 0x021B0014 0x01FF00DB /* MMDC_MDCFG2 */ > +DATA 4 0x021B0008 0x1B333030 /* MMDC_MDOTC */ > +DATA 4 0x021B0018 0x00201740 /* MMDC_MDMISC */ > +DATA 4 0x021B002C 0x000026D2 /* MMDC_MDRWD */ > +DATA 4 0x021B0040 0x0000004F /* MMDC_MDASP */ > +DATA 4 0x021B0030 0x006B1023 /* MMDC_MDOR */ > +DATA 4 0x021B0000 0x84180000 /* MMDC_MDCTL */ > + > +/* Calibration */ > +DATA 4 0x021B0800 0xA1390003 /* MMDC_MPZQHWCTRL */ > +DATA 4 0x021B080C 0x000D000F /* MMDC_MPWLDECTRL0 */ > +DATA 4 0x021B0810 0x00100010 /* MMDC_MPWLDECTRL1 */ > +DATA 4 0x021B083C 0x415C0160 /* MMDC_MPDGCTRL0 */ > +DATA 4 0x021B0840 0x00000000 /* MMDC_MPDGCTRL1 */ > +DATA 4 0x021B0848 0x40403C42 /* MMDC_MPRDDLCTL */ > +DATA 4 0x021B0850 0x40402C26 /* MMDC_MPWRDLCTL */ > +DATA 4 0x021B081C 0x33333333 /* MMDC_MPRDDQBY0DL */ > +DATA 4 0x021B0820 0x33333333 /* MMDC_MPRDDQBY1DL */ > +DATA 4 0x021B082C 0xf3333333 /* MMDC_MPWRDQBY0DL */ > +DATA 4 0x021B0830 0xf3333333 /* MMDC_MPWRDQBY1DL */ > +DATA 4 0x021B08C0 0x00921012 /* MMDC_MPDCCR */ > +DATA 4 0x021B08B8 0x00000800 /* MMDC_MPMUR0 */ > + > +/* JEDEC initialization sequence */ > +DATA 4 0x021B001C 0x02008032 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x00008033 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x00048031 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x15208030 /* MMDC_MDSCR */ > +DATA 4 0x021B001C 0x04008040 /* MMDC_MDSCR */ > + > +DATA 4 0x021B0004 0x0002556D /* MMDC_MDPDC */ > +DATA 4 0x021B0404 0x00011006 /* MMDC_MAPSR */ > +DATA 4 0x021B0020 0x00000800 /* MMDC_MDREF */ > +DATA 4 0x021B0818 0x00000227 /* MMDC_MPODTCTRL */ > + > +DATA 4 0x021B001C 0x00000000 /* MMDC_MDSCR */ > diff --git a/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c b/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c > new file mode 100644 > index 0000000000..97723992ba > --- /dev/null > +++ b/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c > @@ -0,0 +1,347 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * USB armory Mk II board initialization > + * https://github.com/inversepath/usbarmory > + * > + * Copyright (C) 2019, F-Secure Corporation > + * Andrej Rosano <andrej.rosano@f-secure.com> > + */ > + > +#include <common.h> > +#include <asm/io.h> > +#include <asm/arch/imx-regs.h> > +#include <asm/arch/sys_proto.h> > +#include <asm/arch/crm_regs.h> > +#include <asm/arch/clock.h> > +#include <asm/arch/iomux.h> > +#include <asm/arch/mx6-pins.h> > +#include <asm/mach-imx/iomux-v3.h> > +#include <linux/errno.h> > +#include <i2c.h> > +#include <mmc.h> > +#include <fsl_esdhc_imx.h> > +#include <asm/gpio.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ > + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ > + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ > + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ > + PAD_CTL_ODE | PAD_CTL_SRE_FAST) > +#define WEAK_PULLUP (PAD_CTL_PUS_100K_UP || \ > + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS || \ > + PAD_CTL_SRE_SLOW) > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ > + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > +#define PAD_JTAG (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_60ohm) > +#define PAD_JTAG_TDO (PAD_CTL_PKE | \ > + PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_60ohm | PAD_CTL_SRE_FAST) > +#define PAD_JTAG_MOD (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_60ohm) > + > +static void setup_iomux_uart(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > +#ifndef CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED > + MX6_PAD_UART2_TX_DATA__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > + MX6_PAD_UART2_RX_DATA__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > + MX6_PAD_UART2_CTS_B__UART2_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL), > + MX6_PAD_UART2_RTS_B__UART2_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL) > +#else > + MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_UART2_CTS_B__GPIO1_IO22 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_UART2_RTS_B__GPIO1_IO23 | MUX_PAD_CTRL(WEAK_PULLUP) > +#endif > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + > +static void setup_iomux_i2c(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > + MX6_PAD_GPIO1_IO02__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), > + MX6_PAD_GPIO1_IO03__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL) > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + > +static void setup_iomux_mmc(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > + /* microSD */ > + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + /* eMMC */ > + MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL) > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} And if you are setting just in U-Boot, why the mux is set into code and not by DT ? This is supported in U-Boot. > + > +static void setup_iomux_misc(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > + /* type-c */ > + MX6_PAD_GPIO1_IO00__GPIO1_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_GPIO1_IO01__GPIO1_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), > + /* crypto */ > + MX6_PAD_ENET2_TX_DATA1__GPIO2_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), > + /* pmic */ > + MX6_PAD_ENET1_TX_EN__WDOG2_WDOG_RST_B_DEB | MUX_PAD_CTRL(WEAK_PULLUP), > + /* usb */ > + MX6_PAD_GPIO1_IO05__ANATOP_OTG2_ID | MUX_PAD_CTRL(WEAK_PULLUP) > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + > +static void setup_iomux_jtag(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > +#ifndef CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED > + MX6_PAD_JTAG_TMS__SJC_TMS | MUX_PAD_CTRL(PAD_JTAG), > + MX6_PAD_JTAG_TRST_B__SJC_TRSTB | MUX_PAD_CTRL(PAD_JTAG), > + MX6_PAD_JTAG_TDI__SJC_TDI | MUX_PAD_CTRL(PAD_JTAG), > + MX6_PAD_JTAG_TDO__SJC_TDO | MUX_PAD_CTRL(PAD_JTAG_TDO), > + MX6_PAD_JTAG_TCK__SJC_TCK | MUX_PAD_CTRL(PAD_JTAG), > + MX6_PAD_JTAG_MOD__SJC_MOD | MUX_PAD_CTRL(PAD_JTAG_MOD), > +#else > + MX6_PAD_JTAG_TMS__GPIO1_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_JTAG_TRST_B__GPIO1_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_JTAG_TDI__GPIO1_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_JTAG_TDO__GPIO1_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_JTAG_TCK__GPIO1_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_JTAG_MOD__GPIO1_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), > +#endif > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + > +static void setup_iomux_unused_boot(void) > +{ > + static const iomux_v3_cfg_t pads[] = { > + > + /* pulled-up/pulled-down pads */ > + MX6_PAD_LCD_DATA05__GPIO3_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), > + MX6_PAD_LCD_DATA11__GPIO3_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL), > + MX6_PAD_LCD_DATA14__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), > + MX6_PAD_LCD_DATA08__GPIO3_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), > + > + /* floating and pulled-up pads */ > + MX6_PAD_LCD_DATA00__GPIO3_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA01__GPIO3_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA02__GPIO3_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA03__GPIO3_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA04__GPIO3_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA06__GPIO3_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA07__GPIO3_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA09__GPIO3_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA10__GPIO3_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA12__GPIO3_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA13__GPIO3_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA15__GPIO3_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA16__GPIO3_IO21 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA17__GPIO3_IO22 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA18__GPIO3_IO23 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA19__GPIO3_IO24 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA20__GPIO3_IO25 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA21__GPIO3_IO26 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA22__GPIO3_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_DATA23__GPIO3_IO28 | MUX_PAD_CTRL(WEAK_PULLUP) > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + > +static void setup_iomux_unused_nc(void) > +{ > + /* Out of reset values define the pin values before the > + ROM is executed so we force all the not connected pins > + to a known state */ > + static const iomux_v3_cfg_t pads[] = { > + > + /* TAMPER pins */ > + MX6_PAD_SNVS_TAMPER0__GPIO5_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER1__GPIO5_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER2__GPIO5_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER3__GPIO5_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER4__GPIO5_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER5__GPIO5_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), > + // FIXME: Configuration of one of the following two pads > + // disables console UART for some reason. > + //MX6_PAD_SNVS_TAMPER6__GPIO5_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), > + //MX6_PAD_SNVS_TAMPER7__GPIO5_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER8__GPIO5_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_SNVS_TAMPER9__GPIO5_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), > + > + /* ENET block */ > + MX6_PAD_ENET1_RX_DATA0__GPIO2_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_RX_DATA1__GPIO2_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_RX_EN__GPIO2_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_TX_DATA0__GPIO2_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_TX_DATA1__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_TX_CLK__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET1_RX_ER__GPIO2_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_RX_DATA0__GPIO2_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_RX_DATA1__GPIO2_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_RX_EN__GPIO2_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_TX_DATA0__GPIO2_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_TX_CLK__GPIO2_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_ENET2_RX_ER__GPIO2_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), > + > + /* CSI block */ > + MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_VSYNC__GPIO4_IO19 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_HSYNC__GPIO4_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA02__GPIO4_IO23 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA03__GPIO4_IO24 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA04__GPIO4_IO25 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA05__GPIO4_IO26 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA06__GPIO4_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_CSI_DATA07__GPIO4_IO28 | MUX_PAD_CTRL(WEAK_PULLUP), > + > + /* GPIO block */ > + MX6_PAD_GPIO1_IO08__GPIO1_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), > + > + /* NAND block */ > + MX6_PAD_NAND_WP_B__GPIO4_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_NAND_READY_B__GPIO4_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_NAND_CE0_B__GPIO4_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_NAND_CE1_B__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_NAND_DQS__GPIO4_IO16 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_NAND_CLE__GPIO4_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), > + > + /* LCD block */ > + MX6_PAD_LCD_CLK__GPIO3_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_ENABLE__GPIO3_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_HSYNC__GPIO3_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_VSYNC__GPIO3_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), > + MX6_PAD_LCD_RESET__GPIO3_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) > + }; > + > + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); > +} > + Ditto. > +static struct fsl_esdhc_cfg usdhc_cfg[2] = { > + {USDHC1_BASE_ADDR}, > + {USDHC2_BASE_ADDR}, > +}; > + > +int board_mmc_getcd(struct mmc *mmc) > +{ > + return 1; > +} > + > +int board_mmc_init(struct bd_info *bis) > +{ > + int ret = 0; > + > + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); > + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); > + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]); > + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]); > + > + return ret; > +} > + > +int board_eth_init(struct bd_info *bis) > +{ > + return usb_eth_initialize(bis); > +} > + > +int dram_init(void) > +{ > + gd->ram_size = imx_ddr_size(); > + return 0; > +} > + > +/* Enable FUSB303 receptacle Type-C controller */ > +int fusb303_init(void) > +{ > + uchar val; > + > + val = 0xbb; > + i2c_set_bus_num(0); > + i2c_write(0x31, 0x5, 1, &val, 1); > + return 0; > +} > + > +int board_early_init_f(void) > +{ > + // i2c initialization should not be moved in dts as otherwise > + // the fsusb303_init() does not have effect. > + setup_iomux_i2c(); > + setup_iomux_uart(); > + setup_iomux_mmc(); > + setup_iomux_unused_boot(); > + setup_iomux_unused_nc(); > + setup_iomux_misc(); > + setup_iomux_jtag(); > + return 0; > +} > + > +int board_init(void) > +{ > + fusb303_init(); > + return 0; > +} > + > +int checkboard(void) > +{ > + puts("Board: F-Secure USB armory Mk II\n"); > + return 0; > +} > + > +#ifndef CONFIG_CMDLINE > +static char *ext2_argv[] = { > + "ext2load", > + "mmc", > + USBARMORY_BOOT_DEV ":1", > + USBARMORY_FIT_ADDR, > + USBARMORY_FIT_PATH, > + USBARMORY_FIT_SIZE > +}; > + > +static char *bootm_argv[] = { > + "bootm", > + USBARMORY_FIT_ADDR "#" USBARMORY_FIT_CONF > +}; > + > +int board_run_command(const char *cmdline) > +{ > + if (do_ext2load(NULL, 0, 6, ext2_argv) != 0) { > + hang(); > + } > + > + do_bootm(NULL, 0, 2, bootm_argv); > + hang(); > + > + return 1; > +} > +#endif > diff --git a/configs/usbarmory-mark-two_defconfig b/configs/usbarmory-mark-two_defconfig > new file mode 100644 > index 0000000000..85600f86ff > --- /dev/null > +++ b/configs/usbarmory-mark-two_defconfig > @@ -0,0 +1,72 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_MX6=y > +CONFIG_SYS_TEXT_BASE=0x87800000 > +CONFIG_TARGET_USBARMORY_MARK_TWO=y > +CONFIG_MX6ULL=y > + > +CONFIG_SYS_DDR_512MB=y > +# CONFIG_SYS_DDR_1GB is not set > + > +# Boot device > +CONFIG_SYS_BOOT_DEV_MICROSD=y > +# CONFIG_SYS_BOOT_DEV_EMMC is not set > + > +# Environment > +CONFIG_ENV_OFFSET=0x100000 > +CONFIG_ENV_SIZE=0x2000 > + > +# Boot mode > +CONFIG_SYS_BOOT_MODE_NORMAL=y > +# CONFIG_SYS_BOOT_MODE_UMS is not set > +# CONFIG_SYS_BOOT_MODE_TFTP is not set > +# CONFIG_SYS_BOOT_MODE_VERIFIED_OPEN is not set > +# CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED is not set > + > +CONFIG_NR_DRAM_BANKS=1 > +CONFIG_USE_BOOTCOMMAND=y > +CONFIG_DOS_PARTITION=y > +CONFIG_FSL_USDHC=y > +CONFIG_SYS_MEMTEST_START=0x80000000 > + > +# Commands > +CONFIG_CMD_DHCP=y > +CONFIG_CMD_EXT2=y > +CONFIG_CMD_FUSE=y > +CONFIG_CMD_I2C=y > +CONFIG_CMD_MEMTEST=y > +CONFIG_CMD_MMC=y > +CONFIG_CMD_PING=y > +CONFIG_CMD_USB=y > + > +# Device model support > +CONFIG_DM=y > +CONFIG_DM_MMC=y > +CONFIG_DM_USB=y > +CONFIG_BLK=y > +CONFIG_OF_LIBFDT=y > +CONFIG_OF_CONTROL=y > +CONFIG_OF_SEPARATE=y > +CONFIG_DEFAULT_DEVICE_TREE="imx6ull-usbarmory" > + > +# Secure/Verified boot > +CONFIG_FSL_CAAM=y > +CONFIG_IMX_HAB=y > +CONFIG_FIT=y > +CONFIG_FIT_SIGNATURE=y > +CONFIG_RSA=y > + > +# USB gadgets > +CONFIG_USB=y > +CONFIG_CI_UDC=y > +CONFIG_USB_GADGET=y > +CONFIG_USB_GADGET_MANUFACTURER="FSL" > +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 > +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 > + > +# UMS gadget > +CONFIG_USB_GADGET_DOWNLOAD=y > +CONFIG_CMD_USB_MASS_STORAGE=y > + > +# Ethernet gadget > +CONFIG_USB_ETHER=y > +CONFIG_USB_ETH_CDC=y > diff --git a/include/configs/usbarmory-mark-two.h b/include/configs/usbarmory-mark-two.h > new file mode 100644 > index 0000000000..4ad19fa8f5 > --- /dev/null > +++ b/include/configs/usbarmory-mark-two.h > @@ -0,0 +1,234 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * USB armory Mk II board configuration settings > + * https://github.com/inversepath/usbarmory > + * > + * Copyright (C) 2019, F-Secure Corporation > + * Andrej Rosano <andrej.rosano@f-secure.com> > + */ > + > +#ifndef __CONFIG_H > +#define __CONFIG_H > + > +#include <asm/arch/imx-regs.h> > +#include "mx6_common.h" > + > +#define CONFIG_BOARD_EARLY_INIT_F > + > +/* UART */ > +#define CONFIG_MXC_UART > +#define CONFIG_MXC_UART_BASE UART2_BASE > + > +/* USB */ > +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) > +#define CONFIG_USBD_HS > + > +/* I2C */ > +#define CONFIG_SYS_I2C > +#define CONFIG_SYS_I2C_MXC > +#define CONFIG_SYS_I2C_SPEED 100000 > +#define CONFIG_SYS_I2C_MXC_I2C1 > + > +/* U-Boot memory offsets */ > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > + > +/* Boot parameters */ > +#define USBARMORY_FIT_PATH "/boot/usbarmory.itb" > +#define USBARMORY_FIT_ADDR "0x80800000" > +#define USBARMORY_FIT_CONF "conf-1" > +#define USBARMORY_FIT_SIZE "0x4000000" > + > +#ifdef CONFIG_SYS_BOOT_DEV_MICROSD > +#define CONFIG_SYS_MMC_ENV_DEV 0 > +#define USBARMORY_BOOT_DEV "0" > +#define BOOT_TARGET_DEVICES(func) func(MMC, mmc, 0) > +#elif CONFIG_SYS_BOOT_DEV_EMMC > +#define CONFIG_SYS_MMC_ENV_DEV 1 > +#define USBARMORY_BOOT_DEV "1" > +#define BOOT_TARGET_DEVICES(func) func(MMC, mmc, 1) > +#endif > + > +/* Bootargs */ > + > +#define CONFIG_USE_BOOTARGS > +#define CONFIG_BOOTARGS "console=ttymxc1,115200 root=/dev/mmcblk" USBARMORY_BOOT_DEV "p1 rootwait rw" > + > +#define CONFIG_HOSTNAME "usbarmory" > +#define CONFIG_SYS_CBSIZE 512 > + > +/* DDR size config */ > + > +#ifdef CONFIG_SYS_DDR_1GB > +#define BOOTENV_DDR_1GB \ > + "fdt_high=0xffffffff\0" \ > + "initrd_high=0xffffffff\0" > +#else > +#define BOOTENV_DDR_1GB > +#endif > + > +/* scripts */ > + > +#define BOOTENV_CHECK_SILICON_REVISION \ > + "check_silicon_revision=" \ > + "echo *** Checking Silicon Revision *** ; " \ > + "setexpr USB_ANALOG_DIGPROG *0x20c8260 ; " \ > + "setexpr imx6_family $USB_ANALOG_DIGPROG '/' 0x10000 ; " \ > + "setexpr silicon_revision $USB_ANALOG_DIGPROG '&' 0xffff ; " \ > + "if itest $imx6_family == 0x64; then " \ > + "if itest $silicon_revision < 0x0002; then " \ > + "echo ; " \ > + "echo \"***********************************************\" ; " \ > + "echo \"* WARNING *\" ; " \ > + "echo \"* i.MX6UltraLight with Silicon Revision < 1.2 *\" ; " \ > + "echo \"* Important security fixes are missing *\" ; " \ > + "echo \"***********************************************\" ; " \ > + "echo ; " \ > + "fi ; " \ > + "fi ; " \ > + "if itest $imx6_family == 0x65; then " \ > + "if itest $silicon_revision < 0x0001; then " \ > + "echo ; " \ > + "echo \"********************************************\" ; " \ > + "echo \"* WARNING *\" ; " \ > + "echo \"* i.MX6ULL/ULZ with Silicon Revision < 1.1 *\" ; " \ > + "echo \"* Important security fixes are missing *\" ; " \ > + "echo \"********************************************\" ; " \ > + "echo ; " \ > + "fi ; " \ > + "fi\0" > + > +#define BOOTENV_CHECK_OTPMK \ > + "check_otpmk=" \ > + "echo *** Checking OTPMK *** ; " \ > + "env set check_otpmk_var 0 ; " \ > + "setexpr SNVS_HPSR *0x020cc014 ; " \ > + "setexpr test $SNVS_HPSR '&' 0x08000000 ; " \ > + "if itest $test != 0; then " \ > + "env set check_otpmk_var 1 ; " \ > + "echo ; " \ > + "echo \"**************************\" ; " \ > + "echo \"* WARNING: OTPMK is zero *\" ; " \ > + "echo \"**************************\" ; " \ > + "echo ; " \ > + "fi ; " \ > + "setexpr test $SNVS_HPSR '&' 0x01FF0000 ; " \ > + "if itest $test != 0; then " \ > + "env set check_otpmk_var 1 ; " \ > + "echo ; " \ > + "echo \"******************************************\" ; " \ > + "echo \"* WARNING: OTPMK_SYNDROME error detected *\" ; " \ > + "echo \"******************************************\" ; " \ > + "echo ; " \ > + "fi ; " \ > + "setexpr test $SNVS_HPSR '&' 0xF00 ; " \ > + "if itest $test != 0xD00; then " \ > + "env set check_otpmk_var 1 ; " \ > + "echo ; " \ > + "echo \"***************************************\" ; " \ > + "echo \"* WARNING: Device not in TRUSTED mode *\" ; " \ > + "echo \"***************************************\" ; " \ > + "echo ; " \ > + "fi ; " \ > + "if itest $check_otpmk_var != 0; then " \ > + "echo *** Unable to continue. Resetting in 60s *** ; " \ > + "sleep 60 ; " \ > + "reset ; " \ > + "fi\0" > + > +#define BOOTENV_UMS \ > + "start_ums=" \ > + "ums 0 mmc ${mmcdev}\0" > + > +#define BOOTENV_TFTP \ > + "start_tftp=" \ > + "dhcp ${kernel_addr_r} ${serverip}:${bootfile} ; " \ > + "dhcp ${fdt_addr_r} ${serverip}:${fdtfile} ; " \ > + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" > + > +#define BOOTENV_VERIFIED_OPEN \ > + "start_verified_open=" \ > + "ext2load mmc ${mmcdev}:1 " USBARMORY_FIT_ADDR " " USBARMORY_FIT_PATH " " USBARMORY_FIT_SIZE " ; " \ > + "bootm " USBARMORY_FIT_ADDR "#" USBARMORY_FIT_CONF "\0" > + > +#define BOOTENV_NORMAL \ > + "start_normal=run distro_bootcmd ; " \ > + "ext2load mmc ${mmcdev}:1 ${kernel_addr_r} /boot/${bootfile} ; "\ > + "ext2load mmc ${mmcdev}:1 ${fdt_addr_r} /boot/${fdtfile} ; " \ > + "bootz ${kernel_addr_r} - ${fdt_addr_r}\0" > + > +/* Boot modes */ > + > +#ifdef CONFIG_SYS_BOOT_MODE_UMS > + > +#undef CONFIG_BOOTCOMMAND > +#define CONFIG_BOOTCOMMAND "run start_ums" > + > +#elif CONFIG_SYS_BOOT_MODE_VERIFIED_OPEN > + > +#undef CONFIG_BOOTCOMMAND > +#define CONFIG_BOOTCOMMAND "run start_verified_open" > + > +#elif CONFIG_SYS_BOOT_MODE_TFTP > + > +#undef CONFIG_BOOTCOMMAND > +#define CONFIG_BOOTCOMMAND "run start_tftp" > + > +#elif CONFIG_SYS_BOOT_MODE_NORMAL > + > +#include <config_distro_bootcmd.h> > +#undef CONFIG_BOOTCOMMAND > +#define CONFIG_BOOTCOMMAND "run start_normal" > + > +#elif CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED > + > +#undef CONFIG_CMDLINE > +#undef CONFIG_BOOTDELAY > +#define CONFIG_BOOTDELAY -2 > + > +#undef CONFIG_BOOTCOMMAND > +#define CONFIG_BOOTCOMMAND "dummy" > + > +#endif > + > +/* Custom environment variables */ > + > +#ifndef BOOTENV > +#define BOOTENV > +#endif > + > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "kernel_addr_r=0x80800000\0" \ > + "fdt_addr_r=0x82000000\0" \ > + "scriptaddr=0x80800000\0" \ > + "ramdisk_addr_r=0x83000000\0" \ > + "bootfile=zImage\0" \ > + "fdtfile=imx6ull-usbarmory.dtb\0" \ > + "mmcdev=" USBARMORY_BOOT_DEV "\0" \ > + "ethact=usb_ether\0" \ > + "cdc_connect_timeout=60\0" \ > + "usbnet_devaddr=1a:55:89:a2:69:52\0" \ > + "usbnet_hostaddr=1a:55:89:a2:69:51\0" \ > + BOOTENV_CHECK_SILICON_REVISION \ > + BOOTENV_CHECK_OTPMK \ > + BOOTENV_NORMAL \ > + BOOTENV_TFTP \ > + BOOTENV_UMS \ > + BOOTENV_VERIFIED_OPEN \ > + BOOTENV_DDR_1GB \ > + BOOTENV > + > +/* Physical Memory Map */ > +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR > + > +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM > +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR > +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE > + > +#define CONFIG_SYS_INIT_SP_OFFSET \ > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) > +#define CONFIG_SYS_INIT_SP_ADDR \ > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) > + > +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) > + > +#endif /* __CONFIG_H */ > Best regards, Stefano Babic
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index b195723f16..d17c14c9bb 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -731,6 +731,7 @@ dtb-$(CONFIG_MX6ULL) += \ imx6ull-myir-mys-6ulx-eval.dtb \ imx6ull-phytec-segin-ff-rdk-emmc.dtb \ imx6ull-dart-6ul.dtb \ + imx6ull-usbarmory.dtb \ imx6ull-somlabs-visionsom.dtb \ imx6ulz-14x14-evk.dtb diff --git a/arch/arm/dts/imx6ull-usbarmory.dts b/arch/arm/dts/imx6ull-usbarmory.dts new file mode 100644 index 0000000000..d5a616f703 --- /dev/null +++ b/arch/arm/dts/imx6ull-usbarmory.dts @@ -0,0 +1,200 @@ +/* + * USB armory Mk II device tree file + * https://github.com/inversepath/usbarmory + * + * Copyright (C) 2019, F-Secure Corporation + * Andrej Rosano <andrej.rosano@f-secure.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "imx6ull.dtsi" + +/ { + model = "F-Secure USB armory Mk II"; + compatible = "inversepath,imx6ull-usbarmory-mkII", "fsl,imx6ull"; + + chosen { + stdout-path = &uart2; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led>; + + led-white { + label = "LED_WHITE"; + gpios = <&gpio4 21 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-blue { + label = "LED_BLUE"; + gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_sd1_vmmc: sd1_regulator { + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; +}; + +&cpu0 { + operating-points = < + /* kHz uV */ + 900000 1275000 + 792000 1225000 + 528000 1175000 + 396000 1025000 + 198000 950000 + >; + fsl,soc-operating-points = < + /* KHz uV */ + 900000 1250000 + 792000 1175000 + 528000 1175000 + 396000 1175000 + 198000 1175000 + >; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_bluetooth>; + uart-has-rtscts; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + no-1-8-v; + keep-power-in-suspend; + wakeup-source; + non-removable; // FIXME: CD works on i.MX6ULL but not i.MX6ULZ + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + non-removable; + status = "okay"; +}; + +&i2c1 { + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&iomuxc { + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_bluetooth: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b0 /* BT_UART_TX */ + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b0 /* BT_UART_RX */ + MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x1b0b0 /* BT_UART_CTS */ + MX6UL_PAD_GPIO1_IO07__UART1_DCE_RTS 0x1b0b0 /* BT_UART_RTS */ + MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24 0x1f020 /* BT_UART_DSR */ + MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25 0x1f020 /* BT_UART_DTR */ + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1f020 /* BT_SWDCLK */ + MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1f020 /* BT_SWDIO */ + MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x1f020 /* BT_RESET */ + MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x1f020 /* BT_SWITCH_1 */ + MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1f020 /* BT_SWITCH_2 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_GPIO1_IO03__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_led: ledgrp { + fsl,pins = < + MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x1f020 + MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x1f020 + >; + }; +}; + +&usbotg1 { + dr_mode = "peripheral"; + disable-over-current; + tpl-support; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + tpl-support; + status = "okay"; +}; diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index 3d72517fa1..36b5d46c4b 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -644,6 +644,10 @@ config TARGET_UDOO_NEO select SUPPORT_SPL imply CMD_DM +config TARGET_USBARMORY_MARK_TWO + bool "Support USB armory Mk II" + depends on MX6ULL + config TARGET_SOFTING_VINING_2000 bool "Softing VIN|ING 2000" depends on MX6SX @@ -744,6 +748,7 @@ source "board/phytec/pcm058/Kconfig" source "board/phytec/pfla02/Kconfig" source "board/phytec/pcl063/Kconfig" source "board/gateworks/gw_ventana/Kconfig" +source "board/inversepath/usbarmory-mark-two/Kconfig" source "board/kosagi/novena/Kconfig" source "board/softing/vining_2000/Kconfig" source "board/liebherr/display5/Kconfig" diff --git a/board/inversepath/usbarmory-mark-two/Kconfig b/board/inversepath/usbarmory-mark-two/Kconfig new file mode 100644 index 0000000000..e13290b9a1 --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/Kconfig @@ -0,0 +1,71 @@ +if TARGET_USBARMORY_MARK_TWO + +choice + prompt "DDR size" + default SYS_DDR_512MB + +config SYS_DDR_512MB + bool "512 MB" + +config SYS_DDR_1GB + bool "1 GB" + +endchoice + +choice + prompt "Boot device" + default SYS_BOOT_DEV_MICROSD + +config SYS_BOOT_DEV_MICROSD + bool "micro SD" + +config SYS_BOOT_DEV_EMMC + bool "eMMC" + +endchoice + +choice + prompt "Boot mode" + default SYS_BOOT_MODE_NORMAL + +config SYS_BOOT_MODE_NORMAL + select DISTRO_DEFAULTS + select ENV_IS_IN_MMC + bool "Normal" + +config SYS_BOOT_MODE_UMS + bool "UMS" + select ENV_IS_NOWHERE + +config SYS_BOOT_MODE_TFTP + bool "TFTP" + select ENV_IS_NOWHERE + +config SYS_BOOT_MODE_VERIFIED_OPEN + bool "Verified Boot" + select ENV_IS_NOWHERE + +config SYS_BOOT_MODE_VERIFIED_LOCKED + bool "Verified Boot and console disabled" + select ENV_IS_NOWHERE + +endchoice + +config IMX_CONFIG + default "board/inversepath/usbarmory-mark-two/imximage-512mb.cfg" if SYS_DDR_512MB + default "board/inversepath/usbarmory-mark-two/imximage-1gb.cfg" if SYS_DDR_1GB + +config SYS_MEMTEST_END + default 0xa0000000 if SYS_DDR_512MB + default 0xc0000000 if SYS_DDR_1G + +config SYS_BOARD + default "usbarmory-mark-two" + +config SYS_VENDOR + default "inversepath" + +config SYS_CONFIG_NAME + default "usbarmory-mark-two" + +endif diff --git a/board/inversepath/usbarmory-mark-two/MAINTAINERS b/board/inversepath/usbarmory-mark-two/MAINTAINERS new file mode 100644 index 0000000000..89b68ae866 --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/MAINTAINERS @@ -0,0 +1,6 @@ +USBARMORY MK II BOARD +M: Andrej Rosano <andrej.rosano@f-secure.com> +S: Maintained +F: board/inversepath/usbarmory-mark-two/ +F: include/configs/usbarmory-mark-two.h +F: configs/usbarmory-mark-two_defconfig diff --git a/board/inversepath/usbarmory-mark-two/Makefile b/board/inversepath/usbarmory-mark-two/Makefile new file mode 100644 index 0000000000..bf84d05bfd --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/Makefile @@ -0,0 +1,10 @@ +# +# USB armory Mk II board Makefile +# https://github.com/inversepath/usbarmory +# +# Copyright (C) 2019, F-Secure +# Andrej Rosano <andrej.rosano@f-secure.com> +# +# SPDX-License-Identifier:|____GPL-2.0+ + +obj-y := usbarmory-mark-two.o diff --git a/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg b/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg new file mode 100644 index 0000000000..47bd4830f7 --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/imximage-1gb.cfg @@ -0,0 +1,87 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * USB armory Mk II board imximage configuration + * https://github.com/inversepath/usbarmory + * + * Copyright (C) 2019, F-Secure Corportation + * Andrej Rosano <andrej.rosano@f-secure.com> + */ + +#define __ASSEMBLY__ +#include <config.h> + +IMAGE_VERSION 2 +BOOT_FROM sd +CSF CONFIG_CSF_SIZE + +/* CCM */ + +DATA 4 0x020c4068 0xffffffff /* CCM_CCGR0 */ +DATA 4 0x020c406c 0xffffffff /* CCM_CCGR1 */ +DATA 4 0x020c4070 0xffffffff /* CCM_CCGR2 */ +DATA 4 0x020c4074 0xffffffff /* CCM_CCGR3 */ +DATA 4 0x020c4078 0xffffffff /* CCM_CCGR4 */ +DATA 4 0x020c407c 0xffffffff /* CCM_CCGR5 */ +DATA 4 0x020c4080 0xffffffff /* CCM_CCGR6 */ + +/* IOMUX */ + +DATA 4 0x020E04B4 0x000C0000 /* GRP_DDR_TYPE */ +DATA 4 0x020E04AC 0x00000000 /* GRP_DDRPKE */ +DATA 4 0x020E027C 0x00000030 /* DRAM_SDCLK0_P */ +DATA 4 0x020E0250 0x00000030 /* DRAM_CAS_B */ +DATA 4 0x020E024C 0x00000030 /* DRAM_RAS_B */ +DATA 4 0x020E0490 0x00000030 /* GRP_ADDDS */ +DATA 4 0x020E0288 0x00000030 /* DRAM_RESET */ +DATA 4 0x020E0270 0x00000000 /* DRAM_SDBA2 */ +DATA 4 0x020E0260 0x00000030 /* DRAM_ODT0 */ +DATA 4 0x020E0264 0x00000030 /* DRAM_ODT1 */ +DATA 4 0x020E04A0 0x00000030 /* GRP_CTLDS */ +DATA 4 0x020E0494 0x00020000 /* GRP_DDRMODE_CTL */ +DATA 4 0x020E0280 0x00000030 /* DRAM_SDQS0_P */ +DATA 4 0x020E0284 0x00000030 /* DRAM_SDQS1_P */ +DATA 4 0x020E04B0 0x00020000 /* GRP_DDRMODE */ +DATA 4 0x020E0498 0x00000030 /* GRP_B0DS */ +DATA 4 0x020E04A4 0x00000030 /* GRP_B1DS */ +DATA 4 0x020E0244 0x00000030 /* DRAM_DQM0 */ +DATA 4 0x020E0248 0x00000030 /* DRAM_DQM1 */ + +/* MMDC */ + +DATA 4 0x021B001C 0x00008000 /* MMDC_MDSCR */ +DATA 4 0x021B000C 0x676B52F3 /* MMDC_MDCFG0 */ +DATA 4 0x021B0010 0xB66D0B63 /* MMDC_MDCFG1 */ +DATA 4 0x021B0014 0x01FF00DB /* MMDC_MDCFG2 */ +DATA 4 0x021B0008 0x1B333030 /* MMDC_MDOTC */ +DATA 4 0x021B0018 0x00201740 /* MMDC_MDMISC */ +DATA 4 0x021B002C 0x000026D2 /* MMDC_MDRWD */ +DATA 4 0x021B0040 0x0000005F /* MMDC_MDASP */ +DATA 4 0x021B0030 0x006B1023 /* MMDC_MDOR */ +DATA 4 0x021B0000 0x85180000 /* MMDC_MDCTL */ + +/* Calibration */ +DATA 4 0x021B0800 0xA1390003 /* MMDC_MPZQHWCTRL */ +DATA 4 0x021B080C 0x00100014 /* MMDC_MPWLDECTRL0 */ +DATA 4 0x021B083C 0x415C015C /* MMDC_MPDGCTRL0 */ +DATA 4 0x021B0848 0x40403A40 /* MMDC_MPRDDLCTL */ +DATA 4 0x021B0850 0x40402626 /* MMDC_MPWRDLCTL */ +DATA 4 0x021B081C 0x33333333 /* MMDC_MPRDDQBY0DL */ +DATA 4 0x021B0820 0x33333333 /* MMDC_MPRDDQBY1DL */ +DATA 4 0x021B082C 0xf3333333 /* MMDC_MPWRDQBY0DL */ +DATA 4 0x021B0830 0xf3333333 /* MMDC_MPWRDQBY1DL */ +DATA 4 0x021B08C0 0x00921012 /* MMDC_MPDCCR */ +DATA 4 0x021B08B8 0x00000800 /* MMDC_MPMUR0 */ + +/* JEDEC initialization sequence */ +DATA 4 0x021B001C 0x02008032 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x00008033 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x00048031 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x15208030 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x04008040 /* MMDC_MDSCR */ + +DATA 4 0x021B0004 0x0002556D /* MMDC_MDPDC */ +DATA 4 0x021B0404 0x00011006 /* MMDC_MAPSR */ +DATA 4 0x021B0020 0x00000800 /* MMDC_MDREF */ +DATA 4 0x021B0818 0x00000227 /* MMDC_MPODTCTRL */ + +DATA 4 0x021B001C 0x00000000 /* MMDC_MDSCR */ diff --git a/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg b/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg new file mode 100644 index 0000000000..b856481b08 --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/imximage-512mb.cfg @@ -0,0 +1,89 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * USB armory Mk II board imximage configuration + * https://github.com/inversepath/usbarmory + * + * Copyright (C) 2019, F-Secure Corportation + * Andrej Rosano <andrej.rosano@f-secure.com> + */ + +#define __ASSEMBLY__ +#include <config.h> + +IMAGE_VERSION 2 +BOOT_FROM sd +CSF CONFIG_CSF_SIZE + +/* CCM */ + +DATA 4 0x020c4068 0xffffffff /* CCM_CCGR0 */ +DATA 4 0x020c406c 0xffffffff /* CCM_CCGR1 */ +DATA 4 0x020c4070 0xffffffff /* CCM_CCGR2 */ +DATA 4 0x020c4074 0xffffffff /* CCM_CCGR3 */ +DATA 4 0x020c4078 0xffffffff /* CCM_CCGR4 */ +DATA 4 0x020c407c 0xffffffff /* CCM_CCGR5 */ +DATA 4 0x020c4080 0xffffffff /* CCM_CCGR6 */ + +/* IOMUX */ + +DATA 4 0x020E04B4 0x000C0000 /* GRP_DDR_TYPE */ +DATA 4 0x020E04AC 0x00000000 /* GRP_DDRPKE */ +DATA 4 0x020E027C 0x00000030 /* DRAM_SDCLK0_P */ +DATA 4 0x020E0250 0x00000030 /* DRAM_CAS_B */ +DATA 4 0x020E024C 0x00000030 /* DRAM_RAS_B */ +DATA 4 0x020E0490 0x00000030 /* GRP_ADDDS */ +DATA 4 0x020E0288 0x00000030 /* DRAM_RESET */ +DATA 4 0x020E0270 0x00000000 /* DRAM_SDBA2 */ +DATA 4 0x020E0260 0x00000030 /* DRAM_ODT0 */ +DATA 4 0x020E0264 0x00000030 /* DRAM_ODT1 */ +DATA 4 0x020E04A0 0x00000030 /* GRP_CTLDS */ +DATA 4 0x020E0494 0x00020000 /* GRP_DDRMODE_CTL */ +DATA 4 0x020E0280 0x00000030 /* DRAM_SDQS0_P */ +DATA 4 0x020E0284 0x00000030 /* DRAM_SDQS1_P */ +DATA 4 0x020E04B0 0x00020000 /* GRP_DDRMODE */ +DATA 4 0x020E0498 0x00000030 /* GRP_B0DS */ +DATA 4 0x020E04A4 0x00000030 /* GRP_B1DS */ +DATA 4 0x020E0244 0x00000030 /* DRAM_DQM0 */ +DATA 4 0x020E0248 0x00000030 /* DRAM_DQM1 */ + +/* MMDC */ + +DATA 4 0x021B001C 0x00008000 /* MMDC_MDSCR */ +DATA 4 0x021B000C 0x676B52F3 /* MMDC_MDCFG0 */ +DATA 4 0x021B0010 0xB66D0B63 /* MMDC_MDCFG1 */ +DATA 4 0x021B0014 0x01FF00DB /* MMDC_MDCFG2 */ +DATA 4 0x021B0008 0x1B333030 /* MMDC_MDOTC */ +DATA 4 0x021B0018 0x00201740 /* MMDC_MDMISC */ +DATA 4 0x021B002C 0x000026D2 /* MMDC_MDRWD */ +DATA 4 0x021B0040 0x0000004F /* MMDC_MDASP */ +DATA 4 0x021B0030 0x006B1023 /* MMDC_MDOR */ +DATA 4 0x021B0000 0x84180000 /* MMDC_MDCTL */ + +/* Calibration */ +DATA 4 0x021B0800 0xA1390003 /* MMDC_MPZQHWCTRL */ +DATA 4 0x021B080C 0x000D000F /* MMDC_MPWLDECTRL0 */ +DATA 4 0x021B0810 0x00100010 /* MMDC_MPWLDECTRL1 */ +DATA 4 0x021B083C 0x415C0160 /* MMDC_MPDGCTRL0 */ +DATA 4 0x021B0840 0x00000000 /* MMDC_MPDGCTRL1 */ +DATA 4 0x021B0848 0x40403C42 /* MMDC_MPRDDLCTL */ +DATA 4 0x021B0850 0x40402C26 /* MMDC_MPWRDLCTL */ +DATA 4 0x021B081C 0x33333333 /* MMDC_MPRDDQBY0DL */ +DATA 4 0x021B0820 0x33333333 /* MMDC_MPRDDQBY1DL */ +DATA 4 0x021B082C 0xf3333333 /* MMDC_MPWRDQBY0DL */ +DATA 4 0x021B0830 0xf3333333 /* MMDC_MPWRDQBY1DL */ +DATA 4 0x021B08C0 0x00921012 /* MMDC_MPDCCR */ +DATA 4 0x021B08B8 0x00000800 /* MMDC_MPMUR0 */ + +/* JEDEC initialization sequence */ +DATA 4 0x021B001C 0x02008032 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x00008033 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x00048031 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x15208030 /* MMDC_MDSCR */ +DATA 4 0x021B001C 0x04008040 /* MMDC_MDSCR */ + +DATA 4 0x021B0004 0x0002556D /* MMDC_MDPDC */ +DATA 4 0x021B0404 0x00011006 /* MMDC_MAPSR */ +DATA 4 0x021B0020 0x00000800 /* MMDC_MDREF */ +DATA 4 0x021B0818 0x00000227 /* MMDC_MPODTCTRL */ + +DATA 4 0x021B001C 0x00000000 /* MMDC_MDSCR */ diff --git a/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c b/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c new file mode 100644 index 0000000000..97723992ba --- /dev/null +++ b/board/inversepath/usbarmory-mark-two/usbarmory-mark-two.c @@ -0,0 +1,347 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * USB armory Mk II board initialization + * https://github.com/inversepath/usbarmory + * + * Copyright (C) 2019, F-Secure Corporation + * Andrej Rosano <andrej.rosano@f-secure.com> + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-pins.h> +#include <asm/mach-imx/iomux-v3.h> +#include <linux/errno.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc_imx.h> +#include <asm/gpio.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) +#define WEAK_PULLUP (PAD_CTL_PUS_100K_UP || \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS || \ + PAD_CTL_SRE_SLOW) +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define PAD_JTAG (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_60ohm) +#define PAD_JTAG_TDO (PAD_CTL_PKE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_60ohm | PAD_CTL_SRE_FAST) +#define PAD_JTAG_MOD (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_60ohm) + +static void setup_iomux_uart(void) +{ + static const iomux_v3_cfg_t pads[] = { +#ifndef CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED + MX6_PAD_UART2_TX_DATA__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART2_RX_DATA__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART2_CTS_B__UART2_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART2_RTS_B__UART2_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL) +#else + MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_UART2_CTS_B__GPIO1_IO22 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_UART2_RTS_B__GPIO1_IO23 | MUX_PAD_CTRL(WEAK_PULLUP) +#endif + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_i2c(void) +{ + static const iomux_v3_cfg_t pads[] = { + MX6_PAD_GPIO1_IO02__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), + MX6_PAD_GPIO1_IO03__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL) + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_mmc(void) +{ + static const iomux_v3_cfg_t pads[] = { + /* microSD */ + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL), + /* eMMC */ + MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL) + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_misc(void) +{ + static const iomux_v3_cfg_t pads[] = { + /* type-c */ + MX6_PAD_GPIO1_IO00__GPIO1_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_GPIO1_IO01__GPIO1_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), + /* crypto */ + MX6_PAD_ENET2_TX_DATA1__GPIO2_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), + /* pmic */ + MX6_PAD_ENET1_TX_EN__WDOG2_WDOG_RST_B_DEB | MUX_PAD_CTRL(WEAK_PULLUP), + /* usb */ + MX6_PAD_GPIO1_IO05__ANATOP_OTG2_ID | MUX_PAD_CTRL(WEAK_PULLUP) + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_jtag(void) +{ + static const iomux_v3_cfg_t pads[] = { +#ifndef CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED + MX6_PAD_JTAG_TMS__SJC_TMS | MUX_PAD_CTRL(PAD_JTAG), + MX6_PAD_JTAG_TRST_B__SJC_TRSTB | MUX_PAD_CTRL(PAD_JTAG), + MX6_PAD_JTAG_TDI__SJC_TDI | MUX_PAD_CTRL(PAD_JTAG), + MX6_PAD_JTAG_TDO__SJC_TDO | MUX_PAD_CTRL(PAD_JTAG_TDO), + MX6_PAD_JTAG_TCK__SJC_TCK | MUX_PAD_CTRL(PAD_JTAG), + MX6_PAD_JTAG_MOD__SJC_MOD | MUX_PAD_CTRL(PAD_JTAG_MOD), +#else + MX6_PAD_JTAG_TMS__GPIO1_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_JTAG_TRST_B__GPIO1_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_JTAG_TDI__GPIO1_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_JTAG_TDO__GPIO1_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_JTAG_TCK__GPIO1_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_JTAG_MOD__GPIO1_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), +#endif + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_unused_boot(void) +{ + static const iomux_v3_cfg_t pads[] = { + + /* pulled-up/pulled-down pads */ + MX6_PAD_LCD_DATA05__GPIO3_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_LCD_DATA11__GPIO3_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_LCD_DATA14__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_LCD_DATA08__GPIO3_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* floating and pulled-up pads */ + MX6_PAD_LCD_DATA00__GPIO3_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA01__GPIO3_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA02__GPIO3_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA03__GPIO3_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA04__GPIO3_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA06__GPIO3_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA07__GPIO3_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA09__GPIO3_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA10__GPIO3_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA12__GPIO3_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA13__GPIO3_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA15__GPIO3_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA16__GPIO3_IO21 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA17__GPIO3_IO22 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA18__GPIO3_IO23 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA19__GPIO3_IO24 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA20__GPIO3_IO25 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA21__GPIO3_IO26 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA22__GPIO3_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_DATA23__GPIO3_IO28 | MUX_PAD_CTRL(WEAK_PULLUP) + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static void setup_iomux_unused_nc(void) +{ + /* Out of reset values define the pin values before the + ROM is executed so we force all the not connected pins + to a known state */ + static const iomux_v3_cfg_t pads[] = { + + /* TAMPER pins */ + MX6_PAD_SNVS_TAMPER0__GPIO5_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER1__GPIO5_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER2__GPIO5_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER3__GPIO5_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER4__GPIO5_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER5__GPIO5_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), + // FIXME: Configuration of one of the following two pads + // disables console UART for some reason. + //MX6_PAD_SNVS_TAMPER6__GPIO5_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), + //MX6_PAD_SNVS_TAMPER7__GPIO5_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER8__GPIO5_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_SNVS_TAMPER9__GPIO5_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), + + /* ENET block */ + MX6_PAD_ENET1_RX_DATA0__GPIO2_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_RX_DATA1__GPIO2_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_RX_EN__GPIO2_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_TX_DATA0__GPIO2_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_TX_DATA1__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_TX_CLK__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET1_RX_ER__GPIO2_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_RX_DATA0__GPIO2_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_RX_DATA1__GPIO2_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_RX_EN__GPIO2_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_TX_DATA0__GPIO2_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_TX_CLK__GPIO2_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_ENET2_RX_ER__GPIO2_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), + + /* CSI block */ + MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_VSYNC__GPIO4_IO19 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_HSYNC__GPIO4_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA02__GPIO4_IO23 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA03__GPIO4_IO24 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA04__GPIO4_IO25 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA05__GPIO4_IO26 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA06__GPIO4_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_CSI_DATA07__GPIO4_IO28 | MUX_PAD_CTRL(WEAK_PULLUP), + + /* GPIO block */ + MX6_PAD_GPIO1_IO08__GPIO1_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), + + /* NAND block */ + MX6_PAD_NAND_WP_B__GPIO4_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_NAND_READY_B__GPIO4_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_NAND_CE0_B__GPIO4_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_NAND_CE1_B__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_NAND_DQS__GPIO4_IO16 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_NAND_CLE__GPIO4_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), + + /* LCD block */ + MX6_PAD_LCD_CLK__GPIO3_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_ENABLE__GPIO3_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_HSYNC__GPIO3_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_VSYNC__GPIO3_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_LCD_RESET__GPIO3_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) + }; + + imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)); +} + +static struct fsl_esdhc_cfg usdhc_cfg[2] = { + {USDHC1_BASE_ADDR}, + {USDHC2_BASE_ADDR}, +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + return 1; +} + +int board_mmc_init(struct bd_info *bis) +{ + int ret = 0; + + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]); + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]); + + return ret; +} + +int board_eth_init(struct bd_info *bis) +{ + return usb_eth_initialize(bis); +} + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + return 0; +} + +/* Enable FUSB303 receptacle Type-C controller */ +int fusb303_init(void) +{ + uchar val; + + val = 0xbb; + i2c_set_bus_num(0); + i2c_write(0x31, 0x5, 1, &val, 1); + return 0; +} + +int board_early_init_f(void) +{ + // i2c initialization should not be moved in dts as otherwise + // the fsusb303_init() does not have effect. + setup_iomux_i2c(); + setup_iomux_uart(); + setup_iomux_mmc(); + setup_iomux_unused_boot(); + setup_iomux_unused_nc(); + setup_iomux_misc(); + setup_iomux_jtag(); + return 0; +} + +int board_init(void) +{ + fusb303_init(); + return 0; +} + +int checkboard(void) +{ + puts("Board: F-Secure USB armory Mk II\n"); + return 0; +} + +#ifndef CONFIG_CMDLINE +static char *ext2_argv[] = { + "ext2load", + "mmc", + USBARMORY_BOOT_DEV ":1", + USBARMORY_FIT_ADDR, + USBARMORY_FIT_PATH, + USBARMORY_FIT_SIZE +}; + +static char *bootm_argv[] = { + "bootm", + USBARMORY_FIT_ADDR "#" USBARMORY_FIT_CONF +}; + +int board_run_command(const char *cmdline) +{ + if (do_ext2load(NULL, 0, 6, ext2_argv) != 0) { + hang(); + } + + do_bootm(NULL, 0, 2, bootm_argv); + hang(); + + return 1; +} +#endif diff --git a/configs/usbarmory-mark-two_defconfig b/configs/usbarmory-mark-two_defconfig new file mode 100644 index 0000000000..85600f86ff --- /dev/null +++ b/configs/usbarmory-mark-two_defconfig @@ -0,0 +1,72 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_TARGET_USBARMORY_MARK_TWO=y +CONFIG_MX6ULL=y + +CONFIG_SYS_DDR_512MB=y +# CONFIG_SYS_DDR_1GB is not set + +# Boot device +CONFIG_SYS_BOOT_DEV_MICROSD=y +# CONFIG_SYS_BOOT_DEV_EMMC is not set + +# Environment +CONFIG_ENV_OFFSET=0x100000 +CONFIG_ENV_SIZE=0x2000 + +# Boot mode +CONFIG_SYS_BOOT_MODE_NORMAL=y +# CONFIG_SYS_BOOT_MODE_UMS is not set +# CONFIG_SYS_BOOT_MODE_TFTP is not set +# CONFIG_SYS_BOOT_MODE_VERIFIED_OPEN is not set +# CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED is not set + +CONFIG_NR_DRAM_BANKS=1 +CONFIG_USE_BOOTCOMMAND=y +CONFIG_DOS_PARTITION=y +CONFIG_FSL_USDHC=y +CONFIG_SYS_MEMTEST_START=0x80000000 + +# Commands +CONFIG_CMD_DHCP=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PING=y +CONFIG_CMD_USB=y + +# Device model support +CONFIG_DM=y +CONFIG_DM_MMC=y +CONFIG_DM_USB=y +CONFIG_BLK=y +CONFIG_OF_LIBFDT=y +CONFIG_OF_CONTROL=y +CONFIG_OF_SEPARATE=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ull-usbarmory" + +# Secure/Verified boot +CONFIG_FSL_CAAM=y +CONFIG_IMX_HAB=y +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_RSA=y + +# USB gadgets +CONFIG_USB=y +CONFIG_CI_UDC=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 + +# UMS gadget +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_CMD_USB_MASS_STORAGE=y + +# Ethernet gadget +CONFIG_USB_ETHER=y +CONFIG_USB_ETH_CDC=y diff --git a/include/configs/usbarmory-mark-two.h b/include/configs/usbarmory-mark-two.h new file mode 100644 index 0000000000..4ad19fa8f5 --- /dev/null +++ b/include/configs/usbarmory-mark-two.h @@ -0,0 +1,234 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * USB armory Mk II board configuration settings + * https://github.com/inversepath/usbarmory + * + * Copyright (C) 2019, F-Secure Corporation + * Andrej Rosano <andrej.rosano@f-secure.com> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/imx-regs.h> +#include "mx6_common.h" + +#define CONFIG_BOARD_EARLY_INIT_F + +/* UART */ +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART2_BASE + +/* USB */ +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_USBD_HS + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_MXC_I2C1 + +/* U-Boot memory offsets */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +/* Boot parameters */ +#define USBARMORY_FIT_PATH "/boot/usbarmory.itb" +#define USBARMORY_FIT_ADDR "0x80800000" +#define USBARMORY_FIT_CONF "conf-1" +#define USBARMORY_FIT_SIZE "0x4000000" + +#ifdef CONFIG_SYS_BOOT_DEV_MICROSD +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define USBARMORY_BOOT_DEV "0" +#define BOOT_TARGET_DEVICES(func) func(MMC, mmc, 0) +#elif CONFIG_SYS_BOOT_DEV_EMMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define USBARMORY_BOOT_DEV "1" +#define BOOT_TARGET_DEVICES(func) func(MMC, mmc, 1) +#endif + +/* Bootargs */ + +#define CONFIG_USE_BOOTARGS +#define CONFIG_BOOTARGS "console=ttymxc1,115200 root=/dev/mmcblk" USBARMORY_BOOT_DEV "p1 rootwait rw" + +#define CONFIG_HOSTNAME "usbarmory" +#define CONFIG_SYS_CBSIZE 512 + +/* DDR size config */ + +#ifdef CONFIG_SYS_DDR_1GB +#define BOOTENV_DDR_1GB \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" +#else +#define BOOTENV_DDR_1GB +#endif + +/* scripts */ + +#define BOOTENV_CHECK_SILICON_REVISION \ + "check_silicon_revision=" \ + "echo *** Checking Silicon Revision *** ; " \ + "setexpr USB_ANALOG_DIGPROG *0x20c8260 ; " \ + "setexpr imx6_family $USB_ANALOG_DIGPROG '/' 0x10000 ; " \ + "setexpr silicon_revision $USB_ANALOG_DIGPROG '&' 0xffff ; " \ + "if itest $imx6_family == 0x64; then " \ + "if itest $silicon_revision < 0x0002; then " \ + "echo ; " \ + "echo \"***********************************************\" ; " \ + "echo \"* WARNING *\" ; " \ + "echo \"* i.MX6UltraLight with Silicon Revision < 1.2 *\" ; " \ + "echo \"* Important security fixes are missing *\" ; " \ + "echo \"***********************************************\" ; " \ + "echo ; " \ + "fi ; " \ + "fi ; " \ + "if itest $imx6_family == 0x65; then " \ + "if itest $silicon_revision < 0x0001; then " \ + "echo ; " \ + "echo \"********************************************\" ; " \ + "echo \"* WARNING *\" ; " \ + "echo \"* i.MX6ULL/ULZ with Silicon Revision < 1.1 *\" ; " \ + "echo \"* Important security fixes are missing *\" ; " \ + "echo \"********************************************\" ; " \ + "echo ; " \ + "fi ; " \ + "fi\0" + +#define BOOTENV_CHECK_OTPMK \ + "check_otpmk=" \ + "echo *** Checking OTPMK *** ; " \ + "env set check_otpmk_var 0 ; " \ + "setexpr SNVS_HPSR *0x020cc014 ; " \ + "setexpr test $SNVS_HPSR '&' 0x08000000 ; " \ + "if itest $test != 0; then " \ + "env set check_otpmk_var 1 ; " \ + "echo ; " \ + "echo \"**************************\" ; " \ + "echo \"* WARNING: OTPMK is zero *\" ; " \ + "echo \"**************************\" ; " \ + "echo ; " \ + "fi ; " \ + "setexpr test $SNVS_HPSR '&' 0x01FF0000 ; " \ + "if itest $test != 0; then " \ + "env set check_otpmk_var 1 ; " \ + "echo ; " \ + "echo \"******************************************\" ; " \ + "echo \"* WARNING: OTPMK_SYNDROME error detected *\" ; " \ + "echo \"******************************************\" ; " \ + "echo ; " \ + "fi ; " \ + "setexpr test $SNVS_HPSR '&' 0xF00 ; " \ + "if itest $test != 0xD00; then " \ + "env set check_otpmk_var 1 ; " \ + "echo ; " \ + "echo \"***************************************\" ; " \ + "echo \"* WARNING: Device not in TRUSTED mode *\" ; " \ + "echo \"***************************************\" ; " \ + "echo ; " \ + "fi ; " \ + "if itest $check_otpmk_var != 0; then " \ + "echo *** Unable to continue. Resetting in 60s *** ; " \ + "sleep 60 ; " \ + "reset ; " \ + "fi\0" + +#define BOOTENV_UMS \ + "start_ums=" \ + "ums 0 mmc ${mmcdev}\0" + +#define BOOTENV_TFTP \ + "start_tftp=" \ + "dhcp ${kernel_addr_r} ${serverip}:${bootfile} ; " \ + "dhcp ${fdt_addr_r} ${serverip}:${fdtfile} ; " \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" + +#define BOOTENV_VERIFIED_OPEN \ + "start_verified_open=" \ + "ext2load mmc ${mmcdev}:1 " USBARMORY_FIT_ADDR " " USBARMORY_FIT_PATH " " USBARMORY_FIT_SIZE " ; " \ + "bootm " USBARMORY_FIT_ADDR "#" USBARMORY_FIT_CONF "\0" + +#define BOOTENV_NORMAL \ + "start_normal=run distro_bootcmd ; " \ + "ext2load mmc ${mmcdev}:1 ${kernel_addr_r} /boot/${bootfile} ; "\ + "ext2load mmc ${mmcdev}:1 ${fdt_addr_r} /boot/${fdtfile} ; " \ + "bootz ${kernel_addr_r} - ${fdt_addr_r}\0" + +/* Boot modes */ + +#ifdef CONFIG_SYS_BOOT_MODE_UMS + +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "run start_ums" + +#elif CONFIG_SYS_BOOT_MODE_VERIFIED_OPEN + +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "run start_verified_open" + +#elif CONFIG_SYS_BOOT_MODE_TFTP + +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "run start_tftp" + +#elif CONFIG_SYS_BOOT_MODE_NORMAL + +#include <config_distro_bootcmd.h> +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "run start_normal" + +#elif CONFIG_SYS_BOOT_MODE_VERIFIED_LOCKED + +#undef CONFIG_CMDLINE +#undef CONFIG_BOOTDELAY +#define CONFIG_BOOTDELAY -2 + +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "dummy" + +#endif + +/* Custom environment variables */ + +#ifndef BOOTENV +#define BOOTENV +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernel_addr_r=0x80800000\0" \ + "fdt_addr_r=0x82000000\0" \ + "scriptaddr=0x80800000\0" \ + "ramdisk_addr_r=0x83000000\0" \ + "bootfile=zImage\0" \ + "fdtfile=imx6ull-usbarmory.dtb\0" \ + "mmcdev=" USBARMORY_BOOT_DEV "\0" \ + "ethact=usb_ether\0" \ + "cdc_connect_timeout=60\0" \ + "usbnet_devaddr=1a:55:89:a2:69:52\0" \ + "usbnet_hostaddr=1a:55:89:a2:69:51\0" \ + BOOTENV_CHECK_SILICON_REVISION \ + BOOTENV_CHECK_OTPMK \ + BOOTENV_NORMAL \ + BOOTENV_TFTP \ + BOOTENV_UMS \ + BOOTENV_VERIFIED_OPEN \ + BOOTENV_DDR_1GB \ + BOOTENV + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) + +#endif /* __CONFIG_H */