| Message ID | 20200630190227.507-1-trini@konsulko.com |
|---|---|
| State | Accepted |
| Delegated to: | Lokesh Vutla |
| Headers | show |
| Series | omap3_beagle: Finish current outstanding DM migrations | expand |
On Tue, Jun 30, 2020 at 2:02 PM Tom Rini <trini@konsulko.com> wrote: > > At this point in time we can now remove our legacy code and switch to > enabling DM for USB and Ethernet. > > Cc: Derald D. Woods <woods.technical@gmail.com> > Cc: Adam Ford <aford173@gmail.com> > Signed-off-by: Tom Rini <trini@konsulko.com> > --- > board/ti/beagle/beagle.c | 70 ---------------------------------- > configs/omap3_beagle_defconfig | 5 ++- > 2 files changed, 4 insertions(+), 71 deletions(-) > > diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c > index 9139ad87d400..9ccd566da370 100644 > --- a/board/ti/beagle/beagle.c > +++ b/board/ti/beagle/beagle.c > @@ -40,11 +40,6 @@ > #include "beagle.h" > #include <command.h> > > -#ifdef CONFIG_USB_EHCI_HCD > -#include <usb.h> > -#include <asm/ehci-omap.h> > -#endif > - > #define TWL4030_I2C_BUS 0 > #define EXPANSION_EEPROM_I2C_BUS 1 > #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 > @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) > } > #endif > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > -static struct musb_hdrc_config musb_config = { > - .multipoint = 1, > - .dyn_fifo = 1, > - .num_eps = 16, > - .ram_bits = 12, > -}; > - > -static struct omap_musb_board_data musb_board_data = { > - .interface_type = MUSB_INTERFACE_ULPI, > -}; > - > -static struct musb_hdrc_platform_data musb_plat = { > -#if defined(CONFIG_USB_MUSB_HOST) > - .mode = MUSB_HOST, > -#elif defined(CONFIG_USB_MUSB_GADGET) > - .mode = MUSB_PERIPHERAL, > -#else > -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" > -#endif > - .config = &musb_config, > - .power = 100, > - .platform_ops = &omap2430_ops, > - .board_data = &musb_board_data, > -}; > -#endif > - > /* > * Routine: misc_init_r > * Description: Configure board specific parts > @@ -506,10 +474,6 @@ int misc_init_r(void) > omap3_dss_enable(); > #endif > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); > -#endif > - > if (generate_fake_mac) > omap_die_id_usbethaddr(); > > @@ -548,37 +512,3 @@ void board_mmc_power_init(void) > twl4030_power_mmc_init(0); > } > #endif > - > -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) > -/* Call usb_stop() before starting the kernel */ > -void show_boot_progress(int val) > -{ > - if (val == BOOTSTAGE_ID_RUN_OS) > - usb_stop(); > -} > - > -static struct omap_usbhs_board_data usbhs_bdata = { > - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, > - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > -}; > - > -int ehci_hcd_init(int index, enum usb_init_type init, > - struct ehci_hccr **hccr, struct ehci_hcor **hcor) > -{ > - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); > -} > - > -int ehci_hcd_stop(int index) > -{ > - return omap_ehci_hcd_stop(); > -} > - > -#endif /* CONFIG_USB_EHCI_HCD */ > - > -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) > -int board_eth_init(bd_t *bis) > -{ > - return usb_eth_initialize(bis); > -} > -#endif > diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig > index ed7cb8f2ff63..b08ffc062d29 100644 > --- a/configs/omap3_beagle_defconfig > +++ b/configs/omap3_beagle_defconfig > @@ -3,11 +3,11 @@ CONFIG_ARM=y > # CONFIG_SPL_USE_ARCH_MEMSET is not set > CONFIG_ARCH_OMAP2PLUS=y > CONFIG_SYS_MALLOC_F_LEN=0x4000 > +CONFIG_SPL_TEXT_BASE=0x40200000 > CONFIG_TARGET_OMAP3_BEAGLE=y > CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 > CONFIG_NR_DRAM_BANKS=2 > CONFIG_SPL=y > -CONFIG_SPL_TEXT_BASE=0x40200000 > CONFIG_DISTRO_DEFAULTS=y > CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" > CONFIG_USE_PREBOOT=y > @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > CONFIG_SPL_NAND_SIMPLE=y > +CONFIG_DM_ETH=y For my boards, I had to modify the -u-boot.dtsi files [1] because the gpmc driver didn't have a driver, so any sub-nodes disappeared leaving the Ethernet unavailable. With the fix Ethernet works. [1] - https://gitlab.denx.de/u-boot/u-boot/-/commit/62ca4aa16fcfaaa15e40ed26fe6826878d55ac59 > CONFIG_SPI=y > CONFIG_DM_SPI=y > CONFIG_OMAP3_SPI=y > CONFIG_USB=y > +CONFIG_DM_USB=y > +# CONFIG_SPL_DM_USB is not set > CONFIG_USB_EHCI_HCD=y > CONFIG_USB_OMAP3=y > CONFIG_USB_MUSB_GADGET=y > -- > 2.17.1 >
On Tue, Jun 30, 2020 at 02:32:46PM -0500, Adam Ford wrote: > On Tue, Jun 30, 2020 at 2:02 PM Tom Rini <trini@konsulko.com> wrote: > > > > At this point in time we can now remove our legacy code and switch to > > enabling DM for USB and Ethernet. > > > > Cc: Derald D. Woods <woods.technical@gmail.com> > > Cc: Adam Ford <aford173@gmail.com> > > Signed-off-by: Tom Rini <trini@konsulko.com> > > --- > > board/ti/beagle/beagle.c | 70 ---------------------------------- > > configs/omap3_beagle_defconfig | 5 ++- > > 2 files changed, 4 insertions(+), 71 deletions(-) > > > > diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c > > index 9139ad87d400..9ccd566da370 100644 > > --- a/board/ti/beagle/beagle.c > > +++ b/board/ti/beagle/beagle.c > > @@ -40,11 +40,6 @@ > > #include "beagle.h" > > #include <command.h> > > > > -#ifdef CONFIG_USB_EHCI_HCD > > -#include <usb.h> > > -#include <asm/ehci-omap.h> > > -#endif > > - > > #define TWL4030_I2C_BUS 0 > > #define EXPANSION_EEPROM_I2C_BUS 1 > > #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 > > @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) > > } > > #endif > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > -static struct musb_hdrc_config musb_config = { > > - .multipoint = 1, > > - .dyn_fifo = 1, > > - .num_eps = 16, > > - .ram_bits = 12, > > -}; > > - > > -static struct omap_musb_board_data musb_board_data = { > > - .interface_type = MUSB_INTERFACE_ULPI, > > -}; > > - > > -static struct musb_hdrc_platform_data musb_plat = { > > -#if defined(CONFIG_USB_MUSB_HOST) > > - .mode = MUSB_HOST, > > -#elif defined(CONFIG_USB_MUSB_GADGET) > > - .mode = MUSB_PERIPHERAL, > > -#else > > -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" > > -#endif > > - .config = &musb_config, > > - .power = 100, > > - .platform_ops = &omap2430_ops, > > - .board_data = &musb_board_data, > > -}; > > -#endif > > - > > /* > > * Routine: misc_init_r > > * Description: Configure board specific parts > > @@ -506,10 +474,6 @@ int misc_init_r(void) > > omap3_dss_enable(); > > #endif > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); > > -#endif > > - > > if (generate_fake_mac) > > omap_die_id_usbethaddr(); > > > > @@ -548,37 +512,3 @@ void board_mmc_power_init(void) > > twl4030_power_mmc_init(0); > > } > > #endif > > - > > -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) > > -/* Call usb_stop() before starting the kernel */ > > -void show_boot_progress(int val) > > -{ > > - if (val == BOOTSTAGE_ID_RUN_OS) > > - usb_stop(); > > -} > > - > > -static struct omap_usbhs_board_data usbhs_bdata = { > > - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > > - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, > > - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > > -}; > > - > > -int ehci_hcd_init(int index, enum usb_init_type init, > > - struct ehci_hccr **hccr, struct ehci_hcor **hcor) > > -{ > > - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); > > -} > > - > > -int ehci_hcd_stop(int index) > > -{ > > - return omap_ehci_hcd_stop(); > > -} > > - > > -#endif /* CONFIG_USB_EHCI_HCD */ > > - > > -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) > > -int board_eth_init(bd_t *bis) > > -{ > > - return usb_eth_initialize(bis); > > -} > > -#endif > > diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig > > index ed7cb8f2ff63..b08ffc062d29 100644 > > --- a/configs/omap3_beagle_defconfig > > +++ b/configs/omap3_beagle_defconfig > > @@ -3,11 +3,11 @@ CONFIG_ARM=y > > # CONFIG_SPL_USE_ARCH_MEMSET is not set > > CONFIG_ARCH_OMAP2PLUS=y > > CONFIG_SYS_MALLOC_F_LEN=0x4000 > > +CONFIG_SPL_TEXT_BASE=0x40200000 > > CONFIG_TARGET_OMAP3_BEAGLE=y > > CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 > > CONFIG_NR_DRAM_BANKS=2 > > CONFIG_SPL=y > > -CONFIG_SPL_TEXT_BASE=0x40200000 > > CONFIG_DISTRO_DEFAULTS=y > > CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" > > CONFIG_USE_PREBOOT=y > > @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > > CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > > CONFIG_SPL_NAND_SIMPLE=y > > +CONFIG_DM_ETH=y > > For my boards, I had to modify the -u-boot.dtsi files [1] because the > gpmc driver didn't have a driver, so any sub-nodes disappeared leaving > the Ethernet unavailable. With the fix Ethernet works. Here beagle ethernet is via an onboard USB ethernet device. My networking tests are as stable as ever (I can't get NFS to work on any of them, but TFTP and EFI network are fine).
On Tue, Jun 30, 2020 at 03:02:27PM -0400, Tom Rini wrote: > At this point in time we can now remove our legacy code and switch to > enabling DM for USB and Ethernet. > > Cc: Derald D. Woods <woods.technical@gmail.com> > Cc: Adam Ford <aford173@gmail.com> > Signed-off-by: Tom Rini <trini@konsulko.com> > --- > board/ti/beagle/beagle.c | 70 ---------------------------------- > configs/omap3_beagle_defconfig | 5 ++- > 2 files changed, 4 insertions(+), 71 deletions(-) > > diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c > index 9139ad87d400..9ccd566da370 100644 > --- a/board/ti/beagle/beagle.c > +++ b/board/ti/beagle/beagle.c > @@ -40,11 +40,6 @@ > #include "beagle.h" > #include <command.h> > > -#ifdef CONFIG_USB_EHCI_HCD > -#include <usb.h> > -#include <asm/ehci-omap.h> > -#endif > - > #define TWL4030_I2C_BUS 0 > #define EXPANSION_EEPROM_I2C_BUS 1 > #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 > @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) > } > #endif > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > -static struct musb_hdrc_config musb_config = { > - .multipoint = 1, > - .dyn_fifo = 1, > - .num_eps = 16, > - .ram_bits = 12, > -}; > - > -static struct omap_musb_board_data musb_board_data = { > - .interface_type = MUSB_INTERFACE_ULPI, > -}; > - > -static struct musb_hdrc_platform_data musb_plat = { > -#if defined(CONFIG_USB_MUSB_HOST) > - .mode = MUSB_HOST, > -#elif defined(CONFIG_USB_MUSB_GADGET) > - .mode = MUSB_PERIPHERAL, > -#else > -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" > -#endif > - .config = &musb_config, > - .power = 100, > - .platform_ops = &omap2430_ops, > - .board_data = &musb_board_data, > -}; > -#endif > - > /* > * Routine: misc_init_r > * Description: Configure board specific parts > @@ -506,10 +474,6 @@ int misc_init_r(void) > omap3_dss_enable(); > #endif > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); > -#endif > - > if (generate_fake_mac) > omap_die_id_usbethaddr(); > > @@ -548,37 +512,3 @@ void board_mmc_power_init(void) > twl4030_power_mmc_init(0); > } > #endif > - > -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) > -/* Call usb_stop() before starting the kernel */ > -void show_boot_progress(int val) > -{ > - if (val == BOOTSTAGE_ID_RUN_OS) > - usb_stop(); > -} > - > -static struct omap_usbhs_board_data usbhs_bdata = { > - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, > - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > -}; > - > -int ehci_hcd_init(int index, enum usb_init_type init, > - struct ehci_hccr **hccr, struct ehci_hcor **hcor) > -{ > - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); > -} > - > -int ehci_hcd_stop(int index) > -{ > - return omap_ehci_hcd_stop(); > -} > - > -#endif /* CONFIG_USB_EHCI_HCD */ > - > -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) > -int board_eth_init(bd_t *bis) > -{ > - return usb_eth_initialize(bis); > -} > -#endif > diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig > index ed7cb8f2ff63..b08ffc062d29 100644 > --- a/configs/omap3_beagle_defconfig > +++ b/configs/omap3_beagle_defconfig > @@ -3,11 +3,11 @@ CONFIG_ARM=y > # CONFIG_SPL_USE_ARCH_MEMSET is not set > CONFIG_ARCH_OMAP2PLUS=y > CONFIG_SYS_MALLOC_F_LEN=0x4000 > +CONFIG_SPL_TEXT_BASE=0x40200000 > CONFIG_TARGET_OMAP3_BEAGLE=y > CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 > CONFIG_NR_DRAM_BANKS=2 > CONFIG_SPL=y > -CONFIG_SPL_TEXT_BASE=0x40200000 > CONFIG_DISTRO_DEFAULTS=y > CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" > CONFIG_USE_PREBOOT=y > @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > CONFIG_SPL_NAND_SIMPLE=y > +CONFIG_DM_ETH=y > CONFIG_SPI=y > CONFIG_DM_SPI=y > CONFIG_OMAP3_SPI=y > CONFIG_USB=y > +CONFIG_DM_USB=y > +# CONFIG_SPL_DM_USB is not set > CONFIG_USB_EHCI_HCD=y > CONFIG_USB_OMAP3=y > CONFIG_USB_MUSB_GADGET=y > -- > 2.17.1 > I tested this patch on my BeagleBoard Rev. C4 and BeagleBoard xM. Tested-by: Derald D. Woods <woods.technical@gmail.com> NOTE: I did have to perform a 'make menuconfig' and set DM_ETH and DM_USB manually though. It may be something cached in my build environment. I mention this because I did perform an additional operation before build. After first use of defconfig: ---8<--------------------------------------------------- [...] arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_stop': u-boot/drivers/usb/host/ehci-hcd.c:1138: undefined reference to `ehci_hcd_stop' arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_init': u-boot/drivers/usb/host/ehci-hcd.c:1153: undefined reference to `ehci_hcd_init' make[2]: *** [u-boot/Makefile:1755: u-boot] Error 1 make[1]: *** [Makefile:167: sub-make] Error 2 ---8<--------------------------------------------------- Derald
On Wed, Jul 01, 2020 at 07:17:04PM -0500, Derald D. Woods wrote: > On Tue, Jun 30, 2020 at 03:02:27PM -0400, Tom Rini wrote: > > At this point in time we can now remove our legacy code and switch to > > enabling DM for USB and Ethernet. > > > > Cc: Derald D. Woods <woods.technical@gmail.com> > > Cc: Adam Ford <aford173@gmail.com> > > Signed-off-by: Tom Rini <trini@konsulko.com> > > --- > > board/ti/beagle/beagle.c | 70 ---------------------------------- > > configs/omap3_beagle_defconfig | 5 ++- > > 2 files changed, 4 insertions(+), 71 deletions(-) > > > > diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c > > index 9139ad87d400..9ccd566da370 100644 > > --- a/board/ti/beagle/beagle.c > > +++ b/board/ti/beagle/beagle.c > > @@ -40,11 +40,6 @@ > > #include "beagle.h" > > #include <command.h> > > > > -#ifdef CONFIG_USB_EHCI_HCD > > -#include <usb.h> > > -#include <asm/ehci-omap.h> > > -#endif > > - > > #define TWL4030_I2C_BUS 0 > > #define EXPANSION_EEPROM_I2C_BUS 1 > > #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 > > @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) > > } > > #endif > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > -static struct musb_hdrc_config musb_config = { > > - .multipoint = 1, > > - .dyn_fifo = 1, > > - .num_eps = 16, > > - .ram_bits = 12, > > -}; > > - > > -static struct omap_musb_board_data musb_board_data = { > > - .interface_type = MUSB_INTERFACE_ULPI, > > -}; > > - > > -static struct musb_hdrc_platform_data musb_plat = { > > -#if defined(CONFIG_USB_MUSB_HOST) > > - .mode = MUSB_HOST, > > -#elif defined(CONFIG_USB_MUSB_GADGET) > > - .mode = MUSB_PERIPHERAL, > > -#else > > -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" > > -#endif > > - .config = &musb_config, > > - .power = 100, > > - .platform_ops = &omap2430_ops, > > - .board_data = &musb_board_data, > > -}; > > -#endif > > - > > /* > > * Routine: misc_init_r > > * Description: Configure board specific parts > > @@ -506,10 +474,6 @@ int misc_init_r(void) > > omap3_dss_enable(); > > #endif > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); > > -#endif > > - > > if (generate_fake_mac) > > omap_die_id_usbethaddr(); > > > > @@ -548,37 +512,3 @@ void board_mmc_power_init(void) > > twl4030_power_mmc_init(0); > > } > > #endif > > - > > -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) > > -/* Call usb_stop() before starting the kernel */ > > -void show_boot_progress(int val) > > -{ > > - if (val == BOOTSTAGE_ID_RUN_OS) > > - usb_stop(); > > -} > > - > > -static struct omap_usbhs_board_data usbhs_bdata = { > > - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > > - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, > > - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > > -}; > > - > > -int ehci_hcd_init(int index, enum usb_init_type init, > > - struct ehci_hccr **hccr, struct ehci_hcor **hcor) > > -{ > > - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); > > -} > > - > > -int ehci_hcd_stop(int index) > > -{ > > - return omap_ehci_hcd_stop(); > > -} > > - > > -#endif /* CONFIG_USB_EHCI_HCD */ > > - > > -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) > > -int board_eth_init(bd_t *bis) > > -{ > > - return usb_eth_initialize(bis); > > -} > > -#endif > > diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig > > index ed7cb8f2ff63..b08ffc062d29 100644 > > --- a/configs/omap3_beagle_defconfig > > +++ b/configs/omap3_beagle_defconfig > > @@ -3,11 +3,11 @@ CONFIG_ARM=y > > # CONFIG_SPL_USE_ARCH_MEMSET is not set > > CONFIG_ARCH_OMAP2PLUS=y > > CONFIG_SYS_MALLOC_F_LEN=0x4000 > > +CONFIG_SPL_TEXT_BASE=0x40200000 > > CONFIG_TARGET_OMAP3_BEAGLE=y > > CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 > > CONFIG_NR_DRAM_BANKS=2 > > CONFIG_SPL=y > > -CONFIG_SPL_TEXT_BASE=0x40200000 > > CONFIG_DISTRO_DEFAULTS=y > > CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" > > CONFIG_USE_PREBOOT=y > > @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > > CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > > CONFIG_SPL_NAND_SIMPLE=y > > +CONFIG_DM_ETH=y > > CONFIG_SPI=y > > CONFIG_DM_SPI=y > > CONFIG_OMAP3_SPI=y > > CONFIG_USB=y > > +CONFIG_DM_USB=y > > +# CONFIG_SPL_DM_USB is not set > > CONFIG_USB_EHCI_HCD=y > > CONFIG_USB_OMAP3=y > > CONFIG_USB_MUSB_GADGET=y > > -- > > 2.17.1 > > > > I tested this patch on my BeagleBoard Rev. C4 and BeagleBoard xM. > > Tested-by: Derald D. Woods <woods.technical@gmail.com> > > NOTE: > > I did have to perform a 'make menuconfig' and set DM_ETH and DM_USB > manually though. It may be something cached in my build environment. I > mention this because I did perform an additional operation before build. > > After first use of defconfig: > ---8<--------------------------------------------------- > > [...] > arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_stop': > u-boot/drivers/usb/host/ehci-hcd.c:1138: undefined reference to `ehci_hcd_stop' > arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_init': > u-boot/drivers/usb/host/ehci-hcd.c:1153: undefined reference to `ehci_hcd_init' > make[2]: *** [u-boot/Makefile:1755: u-boot] Error 1 > make[1]: *** [Makefile:167: sub-make] Error 2 > > ---8<--------------------------------------------------- That's just very odd. If you start from a clean tree and apply the patch is it reproducible? Thanks!
On Wed, Jul 01, 2020 at 08:50:19PM -0400, Tom Rini wrote: > On Wed, Jul 01, 2020 at 07:17:04PM -0500, Derald D. Woods wrote: > > On Tue, Jun 30, 2020 at 03:02:27PM -0400, Tom Rini wrote: > > > At this point in time we can now remove our legacy code and switch to > > > enabling DM for USB and Ethernet. > > > > > > Cc: Derald D. Woods <woods.technical@gmail.com> > > > Cc: Adam Ford <aford173@gmail.com> > > > Signed-off-by: Tom Rini <trini@konsulko.com> > > > --- > > > board/ti/beagle/beagle.c | 70 ---------------------------------- > > > configs/omap3_beagle_defconfig | 5 ++- > > > 2 files changed, 4 insertions(+), 71 deletions(-) > > > > > > diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c > > > index 9139ad87d400..9ccd566da370 100644 > > > --- a/board/ti/beagle/beagle.c > > > +++ b/board/ti/beagle/beagle.c > > > @@ -40,11 +40,6 @@ > > > #include "beagle.h" > > > #include <command.h> > > > > > > -#ifdef CONFIG_USB_EHCI_HCD > > > -#include <usb.h> > > > -#include <asm/ehci-omap.h> > > > -#endif > > > - > > > #define TWL4030_I2C_BUS 0 > > > #define EXPANSION_EEPROM_I2C_BUS 1 > > > #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 > > > @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) > > > } > > > #endif > > > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > > -static struct musb_hdrc_config musb_config = { > > > - .multipoint = 1, > > > - .dyn_fifo = 1, > > > - .num_eps = 16, > > > - .ram_bits = 12, > > > -}; > > > - > > > -static struct omap_musb_board_data musb_board_data = { > > > - .interface_type = MUSB_INTERFACE_ULPI, > > > -}; > > > - > > > -static struct musb_hdrc_platform_data musb_plat = { > > > -#if defined(CONFIG_USB_MUSB_HOST) > > > - .mode = MUSB_HOST, > > > -#elif defined(CONFIG_USB_MUSB_GADGET) > > > - .mode = MUSB_PERIPHERAL, > > > -#else > > > -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" > > > -#endif > > > - .config = &musb_config, > > > - .power = 100, > > > - .platform_ops = &omap2430_ops, > > > - .board_data = &musb_board_data, > > > -}; > > > -#endif > > > - > > > /* > > > * Routine: misc_init_r > > > * Description: Configure board specific parts > > > @@ -506,10 +474,6 @@ int misc_init_r(void) > > > omap3_dss_enable(); > > > #endif > > > > > > -#ifdef CONFIG_USB_MUSB_OMAP2PLUS > > > - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); > > > -#endif > > > - > > > if (generate_fake_mac) > > > omap_die_id_usbethaddr(); > > > > > > @@ -548,37 +512,3 @@ void board_mmc_power_init(void) > > > twl4030_power_mmc_init(0); > > > } > > > #endif > > > - > > > -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) > > > -/* Call usb_stop() before starting the kernel */ > > > -void show_boot_progress(int val) > > > -{ > > > - if (val == BOOTSTAGE_ID_RUN_OS) > > > - usb_stop(); > > > -} > > > - > > > -static struct omap_usbhs_board_data usbhs_bdata = { > > > - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > > > - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, > > > - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > > > -}; > > > - > > > -int ehci_hcd_init(int index, enum usb_init_type init, > > > - struct ehci_hccr **hccr, struct ehci_hcor **hcor) > > > -{ > > > - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); > > > -} > > > - > > > -int ehci_hcd_stop(int index) > > > -{ > > > - return omap_ehci_hcd_stop(); > > > -} > > > - > > > -#endif /* CONFIG_USB_EHCI_HCD */ > > > - > > > -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) > > > -int board_eth_init(bd_t *bis) > > > -{ > > > - return usb_eth_initialize(bis); > > > -} > > > -#endif > > > diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig > > > index ed7cb8f2ff63..b08ffc062d29 100644 > > > --- a/configs/omap3_beagle_defconfig > > > +++ b/configs/omap3_beagle_defconfig > > > @@ -3,11 +3,11 @@ CONFIG_ARM=y > > > # CONFIG_SPL_USE_ARCH_MEMSET is not set > > > CONFIG_ARCH_OMAP2PLUS=y > > > CONFIG_SYS_MALLOC_F_LEN=0x4000 > > > +CONFIG_SPL_TEXT_BASE=0x40200000 > > > CONFIG_TARGET_OMAP3_BEAGLE=y > > > CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 > > > CONFIG_NR_DRAM_BANKS=2 > > > CONFIG_SPL=y > > > -CONFIG_SPL_TEXT_BASE=0x40200000 > > > CONFIG_DISTRO_DEFAULTS=y > > > CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" > > > CONFIG_USE_PREBOOT=y > > > @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > > > CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > > > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > > > CONFIG_SPL_NAND_SIMPLE=y > > > +CONFIG_DM_ETH=y > > > CONFIG_SPI=y > > > CONFIG_DM_SPI=y > > > CONFIG_OMAP3_SPI=y > > > CONFIG_USB=y > > > +CONFIG_DM_USB=y > > > +# CONFIG_SPL_DM_USB is not set > > > CONFIG_USB_EHCI_HCD=y > > > CONFIG_USB_OMAP3=y > > > CONFIG_USB_MUSB_GADGET=y > > > -- > > > 2.17.1 > > > > > > > I tested this patch on my BeagleBoard Rev. C4 and BeagleBoard xM. > > > > Tested-by: Derald D. Woods <woods.technical@gmail.com> > > > > NOTE: > > > > I did have to perform a 'make menuconfig' and set DM_ETH and DM_USB > > manually though. It may be something cached in my build environment. I > > mention this because I did perform an additional operation before build. > > > > After first use of defconfig: > > ---8<--------------------------------------------------- > > > > [...] > > arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_stop': > > u-boot/drivers/usb/host/ehci-hcd.c:1138: undefined reference to `ehci_hcd_stop' > > arm-cortexa8-linux-gnueabihf-ld.bfd: drivers/usb/host/built-in.o: in function `usb_lowlevel_init': > > u-boot/drivers/usb/host/ehci-hcd.c:1153: undefined reference to `ehci_hcd_init' > > make[2]: *** [u-boot/Makefile:1755: u-boot] Error 1 > > make[1]: *** [Makefile:167: sub-make] Error 2 > > > > ---8<--------------------------------------------------- > > That's just very odd. If you start from a clean tree and apply the > patch is it reproducible? Thanks! > > -- > Tom I cleaned up my cached configs and the defconfig builds properly now. My redundancy was a bit too aggressive. All good. Derald
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c index 9139ad87d400..9ccd566da370 100644 --- a/board/ti/beagle/beagle.c +++ b/board/ti/beagle/beagle.c @@ -40,11 +40,6 @@ #include "beagle.h" #include <command.h> -#ifdef CONFIG_USB_EHCI_HCD -#include <usb.h> -#include <asm/ehci-omap.h> -#endif - #define TWL4030_I2C_BUS 0 #define EXPANSION_EEPROM_I2C_BUS 1 #define EXPANSION_EEPROM_I2C_ADDRESS 0x50 @@ -297,33 +292,6 @@ static void beagle_dvi_pup(void) } #endif -#ifdef CONFIG_USB_MUSB_OMAP2PLUS -static struct musb_hdrc_config musb_config = { - .multipoint = 1, - .dyn_fifo = 1, - .num_eps = 16, - .ram_bits = 12, -}; - -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, -}; - -static struct musb_hdrc_platform_data musb_plat = { -#if defined(CONFIG_USB_MUSB_HOST) - .mode = MUSB_HOST, -#elif defined(CONFIG_USB_MUSB_GADGET) - .mode = MUSB_PERIPHERAL, -#else -#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" -#endif - .config = &musb_config, - .power = 100, - .platform_ops = &omap2430_ops, - .board_data = &musb_board_data, -}; -#endif - /* * Routine: misc_init_r * Description: Configure board specific parts @@ -506,10 +474,6 @@ int misc_init_r(void) omap3_dss_enable(); #endif -#ifdef CONFIG_USB_MUSB_OMAP2PLUS - musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); -#endif - if (generate_fake_mac) omap_die_id_usbethaddr(); @@ -548,37 +512,3 @@ void board_mmc_power_init(void) twl4030_power_mmc_init(0); } #endif - -#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD) -/* Call usb_stop() before starting the kernel */ -void show_boot_progress(int val) -{ - if (val == BOOTSTAGE_ID_RUN_OS) - usb_stop(); -} - -static struct omap_usbhs_board_data usbhs_bdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED -}; - -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); -} - -int ehci_hcd_stop(int index) -{ - return omap_ehci_hcd_stop(); -} - -#endif /* CONFIG_USB_EHCI_HCD */ - -#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) -int board_eth_init(bd_t *bis) -{ - return usb_eth_initialize(bis); -} -#endif diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig index ed7cb8f2ff63..b08ffc062d29 100644 --- a/configs/omap3_beagle_defconfig +++ b/configs/omap3_beagle_defconfig @@ -3,11 +3,11 @@ CONFIG_ARM=y # CONFIG_SPL_USE_ARCH_MEMSET is not set CONFIG_ARCH_OMAP2PLUS=y CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_TARGET_OMAP3_BEAGLE=y CONFIG_SPL_SYS_MALLOC_F_LEN=0x400 CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0x40200000 CONFIG_DISTRO_DEFAULTS=y CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" CONFIG_USE_PREBOOT=y @@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 CONFIG_SPL_NAND_SIMPLE=y +CONFIG_DM_ETH=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y CONFIG_USB=y +CONFIG_DM_USB=y +# CONFIG_SPL_DM_USB is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y
At this point in time we can now remove our legacy code and switch to enabling DM for USB and Ethernet. Cc: Derald D. Woods <woods.technical@gmail.com> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> --- board/ti/beagle/beagle.c | 70 ---------------------------------- configs/omap3_beagle_defconfig | 5 ++- 2 files changed, 4 insertions(+), 71 deletions(-)