diff mbox series

[04/16] arm: Remove mx51evk board

Message ID 20200613135455.181483-5-jagan@amarulasolutions.com
State New
Delegated to: Jagannadha Sutradharudu Teki
Headers show
Series spi: dm-conversion (part3) | expand

Commit Message

Jagan Teki June 13, 2020, 1:54 p.m. UTC
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 arch/arm/mach-imx/mx5/Kconfig           |   6 -
 board/freescale/mx51evk/Kconfig         |  15 -
 board/freescale/mx51evk/MAINTAINERS     |   6 -
 board/freescale/mx51evk/Makefile        |   8 -
 board/freescale/mx51evk/imximage.cfg    | 108 -------
 board/freescale/mx51evk/mx51evk.c       | 401 ------------------------
 board/freescale/mx51evk/mx51evk_video.c |  98 ------
 configs/mx51evk_defconfig               |  42 ---
 include/configs/mx51evk.h               | 197 ------------
 9 files changed, 881 deletions(-)
 delete mode 100644 board/freescale/mx51evk/Kconfig
 delete mode 100644 board/freescale/mx51evk/MAINTAINERS
 delete mode 100644 board/freescale/mx51evk/Makefile
 delete mode 100644 board/freescale/mx51evk/imximage.cfg
 delete mode 100644 board/freescale/mx51evk/mx51evk.c
 delete mode 100644 board/freescale/mx51evk/mx51evk_video.c
 delete mode 100644 configs/mx51evk_defconfig
 delete mode 100644 include/configs/mx51evk.h
diff mbox series

Patch

diff --git a/arch/arm/mach-imx/mx5/Kconfig b/arch/arm/mach-imx/mx5/Kconfig
index bde37bb97e..dd21aea342 100644
--- a/arch/arm/mach-imx/mx5/Kconfig
+++ b/arch/arm/mach-imx/mx5/Kconfig
@@ -39,11 +39,6 @@  config TARGET_M53MENLO
 	select MX53
 	select SUPPORT_SPL
 
-config TARGET_MX51EVK
-	bool "Support mx51evk"
-	select BOARD_LATE_INIT
-	select MX51
-
 config TARGET_MX53ARD
 	bool "Support mx53ard"
 	select MX53
@@ -90,7 +85,6 @@  config SYS_SOC
 	default "mx5"
 
 source "board/beckhoff/mx53cx9020/Kconfig"
-source "board/freescale/mx51evk/Kconfig"
 source "board/freescale/mx53ard/Kconfig"
 source "board/freescale/mx53evk/Kconfig"
 source "board/freescale/mx53loco/Kconfig"
diff --git a/board/freescale/mx51evk/Kconfig b/board/freescale/mx51evk/Kconfig
deleted file mode 100644
index f9b69cbd66..0000000000
--- a/board/freescale/mx51evk/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@ 
-if TARGET_MX51EVK
-
-config SYS_BOARD
-	default "mx51evk"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_SOC
-	default "mx5"
-
-config SYS_CONFIG_NAME
-	default "mx51evk"
-
-endif
diff --git a/board/freescale/mx51evk/MAINTAINERS b/board/freescale/mx51evk/MAINTAINERS
deleted file mode 100644
index 0e5f22c26b..0000000000
--- a/board/freescale/mx51evk/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@ 
-MX51EVK BOARD
-M:	Stefano Babic <sbabic@denx.de>
-S:	Maintained
-F:	board/freescale/mx51evk/
-F:	include/configs/mx51evk.h
-F:	configs/mx51evk_defconfig
diff --git a/board/freescale/mx51evk/Makefile b/board/freescale/mx51evk/Makefile
deleted file mode 100644
index 1a9581cabf..0000000000
--- a/board/freescale/mx51evk/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@ 
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2009 Freescale Semiconductor, Inc.
-
-obj-y			+= mx51evk.o
-obj-$(CONFIG_VIDEO)	+= mx51evk_video.o
diff --git a/board/freescale/mx51evk/imximage.cfg b/board/freescale/mx51evk/imximage.cfg
deleted file mode 100644
index ff2ec4aa27..0000000000
--- a/board/freescale/mx51evk/imximage.cfg
+++ /dev/null
@@ -1,108 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C Copyright 2009
- * Stefano Babic DENX Software Engineering sbabic@denx.de.
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM	spi
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type           Address        Value
- *
- * where:
- *	Addr-type register length (1,2 or 4 bytes)
- *	Address	  absolute address of the register
- *	value	  value to be stored in the register
- */
-
-/* Setting IOMUXC */
-DATA 4 0x73FA88a0 0x200
-DATA 4 0x73FA850c 0x20c5
-DATA 4 0x73FA8510 0x20c5
-DATA 4 0x73FA883c 0x2
-DATA 4 0x73FA8848 0x2
-DATA 4 0x73FA84b8 0xe7
-DATA 4 0x73FA84bc 0x45
-DATA 4 0x73FA84c0 0x45
-DATA 4 0x73FA84c4 0x45
-DATA 4 0x73FA84c8 0x45
-DATA 4 0x73FA8820 0x0
-DATA 4 0x73FA84a4 0x3
-DATA 4 0x73FA84a8 0x3
-DATA 4 0x73FA84ac 0xe3
-DATA 4 0x73FA84b0 0xe3
-DATA 4 0x73FA84b4 0xe3
-DATA 4 0x73FA84cc 0xe3
-DATA 4 0x73FA84d0 0xe2
-
-DATA 4 0x73FA882c 0x6
-DATA 4 0x73FA88a4 0x6
-DATA 4 0x73FA88ac 0x6
-DATA 4 0x73FA88b8 0x6
-
-/*
- * Setting DDR for micron
- * 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model
- * CAS=3 BL=4
- */
-/* ESDCTL_ESDCTL0 */
-DATA 4 0x83FD9000 0x82a20000
-/* ESDCTL_ESDCTL1 */
-DATA 4 0x83FD9008 0x82a20000
-/* ESDCTL_ESDMISC */
-DATA 4 0x83FD9010 0x000ad0d0
-/* ESDCTL_ESDCFG0 */
-DATA 4 0x83FD9004 0x333574aa
-/* ESDCTL_ESDCFG1 */
-DATA 4 0x83FD900C 0x333574aa
-
-/* Init DRAM on CS0 */
-/* ESDCTL_ESDSCR */
-DATA 4 0x83FD9014 0x04008008
-DATA 4 0x83FD9014 0x0000801a
-DATA 4 0x83FD9014 0x0000801b
-DATA 4 0x83FD9014 0x00448019
-DATA 4 0x83FD9014 0x07328018
-DATA 4 0x83FD9014 0x04008008
-DATA 4 0x83FD9014 0x00008010
-DATA 4 0x83FD9014 0x00008010
-DATA 4 0x83FD9014 0x06328018
-DATA 4 0x83FD9014 0x03808019
-DATA 4 0x83FD9014 0x00408019
-DATA 4 0x83FD9014 0x00008000
-
-/* Init DRAM on CS1 */
-DATA 4 0x83FD9014 0x0400800c
-DATA 4 0x83FD9014 0x0000801e
-DATA 4 0x83FD9014 0x0000801f
-DATA 4 0x83FD9014 0x0000801d
-DATA 4 0x83FD9014 0x0732801c
-DATA 4 0x83FD9014 0x0400800c
-DATA 4 0x83FD9014 0x00008014
-DATA 4 0x83FD9014 0x00008014
-DATA 4 0x83FD9014 0x0632801c
-DATA 4 0x83FD9014 0x0380801d
-DATA 4 0x83FD9014 0x0040801d
-DATA 4 0x83FD9014 0x00008004
-
-/* Write to CTL0 */
-DATA 4 0x83FD9000 0xb2a20000
-/* Write to CTL1 */
-DATA 4 0x83FD9008 0xb2a20000
-/* ESDMISC */
-DATA 4 0x83FD9010 0x000ad6d0
-/* ESDCTL_ESDCDLYGD */
-DATA 4 0x83FD9034 0x90000000
-DATA 4 0x83FD9014 0x00000000
diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
deleted file mode 100644
index 46037acc0e..0000000000
--- a/board/freescale/mx51evk/mx51evk.c
+++ /dev/null
@@ -1,401 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux-mx51.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/clock.h>
-#include <asm/mach-imx/mx5_video.h>
-#include <i2c.h>
-#include <input.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <power/pmic.h>
-#include <fsl_pmic.h>
-#include <mc13892.h>
-#include <usb/ehci-ci.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[2] = {
-	{MMC_SDHC1_BASE_ADDR},
-	{MMC_SDHC2_BASE_ADDR},
-};
-#endif
-
-int dram_init(void)
-{
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
-				PHYS_SDRAM_1_SIZE);
-	return 0;
-}
-
-u32 get_board_rev(void)
-{
-	u32 rev = get_cpu_rev();
-	if (!gpio_get_value(IMX_GPIO_NR(1, 22)))
-		rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET;
-	return rev;
-}
-
-#define UART_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_HIGH)
-
-static void setup_iomux_uart(void)
-{
-	static const iomux_v3_cfg_t uart_pads[] = {
-		MX51_PAD_UART1_RXD__UART1_RXD,
-		MX51_PAD_UART1_TXD__UART1_TXD,
-		NEW_PAD_CTRL(MX51_PAD_UART1_RTS__UART1_RTS, UART_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_UART1_CTS__UART1_CTS, UART_PAD_CTRL),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-}
-
-static void setup_iomux_fec(void)
-{
-	static const iomux_v3_cfg_t fec_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS |
-				PAD_CTL_PUS_22K_UP | PAD_CTL_ODE |
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		MX51_PAD_NANDF_CS3__FEC_MDC,
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
-		MX51_PAD_NANDF_D9__FEC_RDATA0,
-		MX51_PAD_NANDF_CS6__FEC_TDATA3,
-		MX51_PAD_NANDF_CS5__FEC_TDATA2,
-		MX51_PAD_NANDF_CS4__FEC_TDATA1,
-		MX51_PAD_NANDF_D8__FEC_TDATA0,
-		MX51_PAD_NANDF_CS7__FEC_TX_EN,
-		MX51_PAD_NANDF_CS2__FEC_TX_ER,
-		MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
-		MX51_PAD_EIM_CS5__FEC_CRS,
-		MX51_PAD_EIM_CS4__FEC_RX_ER,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-#ifdef CONFIG_MXC_SPI
-static void setup_iomux_spi(void)
-{
-	static const iomux_v3_cfg_t spi_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS |
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS |
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1,
-				MX51_GPIO_PAD_CTRL),
-		MX51_PAD_CSPI1_SS0__ECSPI1_SS0,
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__ECSPI1_RDY, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS |
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
-}
-#endif
-
-#ifdef CONFIG_USB_EHCI_MX5
-#define MX51EVK_USBH1_HUB_RST	IMX_GPIO_NR(1, 7)
-#define MX51EVK_USBH1_STP	IMX_GPIO_NR(1, 27)
-#define MX51EVK_USB_CLK_EN_B	IMX_GPIO_NR(2, 1)
-#define MX51EVK_USB_PHY_RESET	IMX_GPIO_NR(2, 5)
-
-static void setup_usb_h1(void)
-{
-	static const iomux_v3_cfg_t usb_h1_pads[] = {
-		MX51_PAD_USBH1_CLK__USBH1_CLK,
-		MX51_PAD_USBH1_DIR__USBH1_DIR,
-		MX51_PAD_USBH1_STP__USBH1_STP,
-		MX51_PAD_USBH1_NXT__USBH1_NXT,
-		MX51_PAD_USBH1_DATA0__USBH1_DATA0,
-		MX51_PAD_USBH1_DATA1__USBH1_DATA1,
-		MX51_PAD_USBH1_DATA2__USBH1_DATA2,
-		MX51_PAD_USBH1_DATA3__USBH1_DATA3,
-		MX51_PAD_USBH1_DATA4__USBH1_DATA4,
-		MX51_PAD_USBH1_DATA5__USBH1_DATA5,
-		MX51_PAD_USBH1_DATA6__USBH1_DATA6,
-		MX51_PAD_USBH1_DATA7__USBH1_DATA7,
-
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, 0), /* H1 hub reset */
-		MX51_PAD_EIM_D17__GPIO2_1,
-		MX51_PAD_EIM_D21__GPIO2_5, /* PHY reset */
-	};
-
-	imx_iomux_v3_setup_multiple_pads(usb_h1_pads, ARRAY_SIZE(usb_h1_pads));
-}
-
-int board_ehci_hcd_init(int port)
-{
-	/* Set USBH1_STP to GPIO and toggle it */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_USBH1_STP__GPIO1_27,
-						MX51_USBH_PAD_CTRL));
-
-	gpio_direction_output(MX51EVK_USBH1_STP, 0);
-	gpio_direction_output(MX51EVK_USB_PHY_RESET, 0);
-	mdelay(10);
-	gpio_set_value(MX51EVK_USBH1_STP, 1);
-
-	/* Set back USBH1_STP to be function */
-	imx_iomux_v3_setup_pad(MX51_PAD_USBH1_STP__USBH1_STP);
-
-	/* De-assert USB PHY RESETB */
-	gpio_set_value(MX51EVK_USB_PHY_RESET, 1);
-
-	/* Drive USB_CLK_EN_B line low */
-	gpio_direction_output(MX51EVK_USB_CLK_EN_B, 0);
-
-	/* Reset USB hub */
-	gpio_direction_output(MX51EVK_USBH1_HUB_RST, 0);
-	mdelay(2);
-	gpio_set_value(MX51EVK_USBH1_HUB_RST, 1);
-	return 0;
-}
-#endif
-
-static void power_init(void)
-{
-	unsigned int val;
-	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
-	struct pmic *p;
-	int ret;
-
-	ret = pmic_init(CONFIG_FSL_PMIC_BUS);
-	if (ret)
-		return;
-
-	p = pmic_get("FSL_PMIC");
-	if (!p)
-		return;
-
-	/* Write needed to Power Gate 2 register */
-	pmic_reg_read(p, REG_POWER_MISC, &val);
-	val &= ~PWGT2SPIEN;
-	pmic_reg_write(p, REG_POWER_MISC, val);
-
-	/* Externally powered */
-	pmic_reg_read(p, REG_CHARGE, &val);
-	val |= ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | CHGAUTOB;
-	pmic_reg_write(p, REG_CHARGE, val);
-
-	/* power up the system first */
-	pmic_reg_write(p, REG_POWER_MISC, PWUP);
-
-	/* Set core voltage to 1.1V */
-	pmic_reg_read(p, REG_SW_0, &val);
-	val = (val & ~SWx_VOLT_MASK) | SWx_1_100V;
-	pmic_reg_write(p, REG_SW_0, val);
-
-	/* Setup VCC (SW2) to 1.25 */
-	pmic_reg_read(p, REG_SW_1, &val);
-	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(p, REG_SW_1, val);
-
-	/* Setup 1V2_DIG1 (SW3) to 1.25 */
-	pmic_reg_read(p, REG_SW_2, &val);
-	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(p, REG_SW_2, val);
-	udelay(50);
-
-	/* Raise the core frequency to 800MHz */
-	writel(0x0, &mxc_ccm->cacrr);
-
-	/* Set switchers in Auto in NORMAL mode & STANDBY mode */
-	/* Setup the switcher mode for SW1 & SW2*/
-	pmic_reg_read(p, REG_SW_4, &val);
-	val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
-		(SWMODE_MASK << SWMODE2_SHIFT)));
-	val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
-		(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
-	pmic_reg_write(p, REG_SW_4, val);
-
-	/* Setup the switcher mode for SW3 & SW4 */
-	pmic_reg_read(p, REG_SW_5, &val);
-	val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) |
-		(SWMODE_MASK << SWMODE4_SHIFT)));
-	val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) |
-		(SWMODE_AUTO_AUTO << SWMODE4_SHIFT);
-	pmic_reg_write(p, REG_SW_5, val);
-
-	/* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */
-	pmic_reg_read(p, REG_SETTING_0, &val);
-	val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK);
-	val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6;
-	pmic_reg_write(p, REG_SETTING_0, val);
-
-	/* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */
-	pmic_reg_read(p, REG_SETTING_1, &val);
-	val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
-	val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775;
-	pmic_reg_write(p, REG_SETTING_1, val);
-
-	/* Configure VGEN3 and VCAM regulators to use external PNP */
-	val = VGEN3CONFIG | VCAMCONFIG;
-	pmic_reg_write(p, REG_MODE_1, val);
-	udelay(200);
-
-	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
-	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
-		VVIDEOEN | VAUDIOEN  | VSDEN;
-	pmic_reg_write(p, REG_MODE_1, val);
-
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_EIM_A20__GPIO2_14,
-						NO_PAD_CTRL));
-	gpio_direction_output(IMX_GPIO_NR(2, 14), 0);
-
-	udelay(500);
-
-	gpio_set_value(IMX_GPIO_NR(2, 14), 1);
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret;
-
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_0__GPIO1_0,
-						NO_PAD_CTRL));
-	gpio_direction_input(IMX_GPIO_NR(1, 0));
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6,
-						NO_PAD_CTRL));
-	gpio_direction_input(IMX_GPIO_NR(1, 6));
-
-	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-		ret = !gpio_get_value(IMX_GPIO_NR(1, 0));
-	else
-		ret = !gpio_get_value(IMX_GPIO_NR(1, 6));
-
-	return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	static const iomux_v3_cfg_t sd1_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX |
-			PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS),
-	};
-
-	static const iomux_v3_cfg_t sd2_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_SD2_CMD__SD2_CMD,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD2_CLK__SD2_CLK,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD2_DATA0__SD2_DATA0,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD2_DATA1__SD2_DATA1,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD2_DATA2__SD2_DATA2,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD2_DATA3__SD2_DATA3,
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6, PAD_CTL_HYS),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_5__GPIO1_5, PAD_CTL_HYS),
-	};
-
-	u32 index;
-	int ret;
-
-	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-	esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
-	for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM;
-			index++) {
-		switch (index) {
-		case 0:
-			imx_iomux_v3_setup_multiple_pads(sd1_pads,
-							 ARRAY_SIZE(sd1_pads));
-			break;
-		case 1:
-			imx_iomux_v3_setup_multiple_pads(sd2_pads,
-							 ARRAY_SIZE(sd2_pads));
-			break;
-		default:
-			printf("Warning: you configured more ESDHC controller"
-				"(%d) as supported by the board(2)\n",
-				CONFIG_SYS_FSL_ESDHC_NUM);
-			return -EINVAL;
-		}
-		ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
-		if (ret)
-			return ret;
-	}
-	return 0;
-}
-#endif
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-	setup_iomux_fec();
-#ifdef CONFIG_USB_EHCI_MX5
-	setup_usb_h1();
-#endif
-	setup_iomux_lcd();
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
-	return 0;
-}
-
-#ifdef CONFIG_BOARD_LATE_INIT
-int board_late_init(void)
-{
-#ifdef CONFIG_MXC_SPI
-	setup_iomux_spi();
-	power_init();
-#endif
-
-	return 0;
-}
-#endif
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
-	return 1;
-}
-
-int checkboard(void)
-{
-	puts("Board: MX51EVK\n");
-
-	return 0;
-}
diff --git a/board/freescale/mx51evk/mx51evk_video.c b/board/freescale/mx51evk/mx51evk_video.c
deleted file mode 100644
index 3715c5d738..0000000000
--- a/board/freescale/mx51evk/mx51evk_video.c
+++ /dev/null
@@ -1,98 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- * Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <common.h>
-#include <env.h>
-#include <linux/list.h>
-#include <asm/gpio.h>
-#include <asm/arch/iomux-mx51.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-
-#define MX51EVK_LCD_3V3		IMX_GPIO_NR(4, 9)
-#define MX51EVK_LCD_5V		IMX_GPIO_NR(4, 10)
-#define MX51EVK_LCD_BACKLIGHT	IMX_GPIO_NR(3, 4)
-
-static struct fb_videomode const claa_wvga = {
-	.name		= "CLAA07LC0ACW",
-	.refresh	= 57,
-	.xres		= 800,
-	.yres		= 480,
-	.pixclock	= 37037,
-	.left_margin	= 40,
-	.right_margin	= 60,
-	.upper_margin	= 10,
-	.lower_margin	= 10,
-	.hsync_len	= 20,
-	.vsync_len	= 10,
-	.sync		= 0,
-	.vmode		= FB_VMODE_NONINTERLACED
-};
-
-static struct fb_videomode const dvi = {
-	.name		= "DVI panel",
-	.refresh	= 60,
-	.xres		= 1024,
-	.yres		= 768,
-	.pixclock	= 15385,
-	.left_margin	= 220,
-	.right_margin	= 40,
-	.upper_margin	= 21,
-	.lower_margin	= 7,
-	.hsync_len	= 60,
-	.vsync_len	= 10,
-	.sync		= 0,
-	.vmode		= FB_VMODE_NONINTERLACED
-};
-
-void setup_iomux_lcd(void)
-{
-	/* DI2_PIN15 */
-	imx_iomux_v3_setup_pad(MX51_PAD_DI_GP4__DI2_PIN15);
-
-	/* Pad settings for DI2_DISP_CLK */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK,
-			    PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_SLOW));
-
-	/* Turn on 3.3V voltage for LCD */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_CSI2_D12__GPIO4_9,
-						NO_PAD_CTRL));
-	gpio_direction_output(MX51EVK_LCD_3V3, 1);
-
-	/* Turn on 5V voltage for LCD */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_CSI2_D13__GPIO4_10,
-						NO_PAD_CTRL));
-	gpio_direction_output(MX51EVK_LCD_5V, 1);
-
-	/* Turn on GPIO backlight */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_DI1_D1_CS__GPIO3_4,
-						NO_PAD_CTRL));
-	gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1);
-}
-
-int board_video_skip(void)
-{
-	int ret;
-	char const *e = env_get("panel");
-
-	if (e) {
-		if (strcmp(e, "claa") == 0) {
-			ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565);
-			if (ret)
-				printf("claa cannot be configured: %d\n", ret);
-			return ret;
-		}
-	}
-
-	/*
-	 * 'panel' env variable not found or has different value than 'claa'
-	 *  Defaulting to dvi output.
-	 */
-	ret = ipuv3_fb_init(&dvi, 0, IPU_PIX_FMT_RGB24);
-	if (ret)
-		printf("dvi cannot be configured: %d\n", ret);
-	return ret;
-}
diff --git a/configs/mx51evk_defconfig b/configs/mx51evk_defconfig
deleted file mode 100644
index dbc4d85a22..0000000000
--- a/configs/mx51evk_defconfig
+++ /dev/null
@@ -1,42 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX5=y
-CONFIG_SYS_TEXT_BASE=0x97800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0xC0000
-CONFIG_TARGET_MX51EVK=y
-CONFIG_NR_DRAM_BANKS=1
-# CONFIG_CMD_BMODE is not set
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx51evk/imximage.cfg"
-CONFIG_USE_PREBOOT=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_FUSE=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_ESDHC_IMX=y
-CONFIG_MTD=y
-CONFIG_MII=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_MX5=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h
deleted file mode 100644
index 182648a0f1..0000000000
--- a/include/configs/mx51evk.h
+++ /dev/null
@@ -1,197 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
- *
- * (C) Copyright 2009 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the MX51EVK Board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
- /* High Level Configuration Options */
-
-#define CONFIG_SYS_FSL_CLK
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
-#define CONFIG_MACH_TYPE	MACH_TYPE_MX51_BABBAGE
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
-
-/*
- * Hardware drivers
- */
-#define CONFIG_FSL_IIM
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE	UART1_BASE
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS	0
-#define CONFIG_FSL_PMIC_CS	0
-#define CONFIG_FSL_PMIC_CLK	2500000
-#define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC_BITLEN	32
-#define CONFIG_RTC_MC13XXX
-
-/*
- * MMC Configs
- * */
-#define CONFIG_SYS_FSL_ESDHC_ADDR	MMC_SDHC1_BASE_ADDR
-#define CONFIG_SYS_FSL_ESDHC_NUM	2
-
-/*
- * Eth Configs
- */
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE	FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR	0x1F
-
-/* USB Configs */
-#define CONFIG_MXC_USB_PORT	1
-#define CONFIG_MXC_USB_PORTSC	PORT_PTS_ULPI
-#define CONFIG_MXC_USB_FLAGS	MXC_EHCI_POWER_PINS_ENABLED
-
-/* Framebuffer and LCD */
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_ETHPRIME		"FEC0"
-
-#define CONFIG_LOADADDR		0x92000000	/* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=boot.scr\0" \
-	"image=zImage\0" \
-	"fdt_file=imx51-babbage.dtb\0" \
-	"fdt_addr=0x91000000\0" \
-	"boot_fdt=try\0" \
-	"ip_dyn=yes\0" \
-	"mmcdev=0\0" \
-	"mmcpart=1\0" \
-	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
-	"mmcargs=setenv bootargs console=ttymxc0,${baudrate} " \
-		"root=${mmcroot}\0" \
-	"loadbootscript=" \
-		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
-	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"run mmcargs; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if run loadfdt; then " \
-				"bootz ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootz; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootz; " \
-		"fi;\0" \
-	"netargs=setenv bootargs console=ttymxc0,${baudrate} " \
-		"root=/dev/nfs " \
-		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
-	"netboot=echo Booting from net ...; " \
-		"run netargs; " \
-		"if test ${ip_dyn} = yes; then " \
-			"setenv get_cmd dhcp; " \
-		"else " \
-			"setenv get_cmd tftp; " \
-		"fi; " \
-		"${get_cmd} ${image}; " \
-		"if test ${boot_fdt} = yes ||  test ${boot_fdt} = try; then " \
-			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
-				"bootz ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootz; " \
-				"else " \
-					"echo ERROR: Cannot load the DT; " \
-					"exit; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootz; " \
-		"fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
-	"mmc dev ${mmcdev}; if mmc rescan; then " \
-		"if run loadbootscript; then " \
-			"run bootscript; " \
-		"else " \
-			"if run loadimage; then " \
-				"run mmcboot; " \
-			"else run netboot; " \
-			"fi; " \
-		"fi; " \
-	"else run netboot; fi"
-
-#define CONFIG_ARP_TIMEOUT	200UL
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define PHYS_SDRAM_1		CSD0_BASE_ADDR
-#define PHYS_SDRAM_1_SIZE	(512 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
-#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
-#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_SYS_DDR_CLKSEL	0
-#define CONFIG_SYS_CLKTL_CBCDR	0x59E35100
-#define CONFIG_SYS_MAIN_PWR_ON
-
-/*-----------------------------------------------------------------------
- * environment organization
- */
-
-/*
- * Environment starts at CONFIG_ENV_OFFSET=0xC0000 = 768k = 768 * 1024 = 786432
- *
- * Detect overlap between U-Boot image and environment area in build-time
- *
- * CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot.imx offset
- * CONFIG_BOARD_SIZE_LIMIT = 768k - 1k = 767k = 785408
- *
- * Currently CONFIG_BOARD_SIZE_LIMIT does not handle expressions, so
- * write the direct value here
- */
-#define CONFIG_BOARD_SIZE_LIMIT		785408
-#define CONFIG_SYS_MMC_ENV_DEV 0
-
-#endif