diff --git a/arch/arm/dts/imx6q-mccmon6.dts b/arch/arm/dts/imx6q-mccmon6.dts
new file mode 100644
index 0000000000..27cde56115
--- /dev/null
+++ b/arch/arm/dts/imx6q-mccmon6.dts
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Liebherr Nenzig (LWN) iMX6Q";
+	compatible = "lwn,imx6-mccmon6", "fsl,imx6";
+
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		spi0 = &ecspi3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@10000000 {
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+	spi-max-frequency = <25000000>;
+	status = "okay";
+
+	s25sl032p: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <10>;
+	phy-reset-post-delay = <1>;
+	/* KSZ9031 PHY SKEW setup - old values * 60 ps */
+	rxc-skew-ps = <1860>;
+	txc-skew-ps = <1860>;
+	txen-skew-ps = <900>;
+	rxdv-skew-ps = <900>;
+	rxd0-skew-ps = <180>;
+	rxd1-skew-ps = <180>;
+	rxd2-skew-ps = <180>;
+	rxd3-skew-ps = <180>;
+	txd0-skew-ps = <120>;
+	txd1-skew-ps = <300>;
+	txd2-skew-ps = <0>;
+	txd3-skew-ps = <120>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pfuze100: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
+	ranges = <0 0 0x08000000 0x08000000>;
+	status = "okay";
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		reg = <0 0 0x02000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		use-advanced-sector-protection;
+		fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+				0x0000c000 0x1404a38e 0x00000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi3_cs: ecspi3csgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000
+		>;
+	};
+
+	pinctrl_ecspi3_flwp: ecspi3flwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x80000000
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27        0x1b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL	0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04           0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+			MX6QDL_PAD_SD3_RST__SD3_RESET		0x17059
+		>;
+	};
+
+	pinctrl_weim_cs0: weimcs0grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_nor: weimnorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+			MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B	0xb060
+			MX6QDL_PAD_EIM_D16__EIM_DATA16		0x1b0b0
+			MX6QDL_PAD_EIM_D17__EIM_DATA17		0x1b0b0
+			MX6QDL_PAD_EIM_D18__EIM_DATA18		0x1b0b0
+			MX6QDL_PAD_EIM_D19__EIM_DATA19		0x1b0b0
+			MX6QDL_PAD_EIM_D20__EIM_DATA20		0x1b0b0
+			MX6QDL_PAD_EIM_D21__EIM_DATA21		0x1b0b0
+			MX6QDL_PAD_EIM_D22__EIM_DATA22		0x1b0b0
+			MX6QDL_PAD_EIM_D23__EIM_DATA23		0x1b0b0
+			MX6QDL_PAD_EIM_D24__EIM_DATA24		0x1b0b0
+			MX6QDL_PAD_EIM_D25__EIM_DATA25		0x1b0b0
+			MX6QDL_PAD_EIM_D26__EIM_DATA26		0x1b0b0
+			MX6QDL_PAD_EIM_D27__EIM_DATA27		0x1b0b0
+			MX6QDL_PAD_EIM_D28__EIM_DATA28		0x1b0b0
+			MX6QDL_PAD_EIM_D29__EIM_DATA29		0x1b0b0
+			MX6QDL_PAD_EIM_D30__EIM_DATA30		0x1b0b0
+			MX6QDL_PAD_EIM_D31__EIM_DATA31		0x1b0b0
+			MX6QDL_PAD_EIM_A23__EIM_ADDR23		0xb0b1
+			MX6QDL_PAD_EIM_A22__EIM_ADDR22		0xb0b1
+			MX6QDL_PAD_EIM_A21__EIM_ADDR21		0xb0b1
+			MX6QDL_PAD_EIM_A20__EIM_ADDR20		0xb0b1
+			MX6QDL_PAD_EIM_A19__EIM_ADDR19		0xb0b1
+			MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0b1
+			MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0b1
+			MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	status = "okay";
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index d0cee514a2..b81ba79f46 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -205,6 +205,13 @@ config TARGET_MCCMON6
 	bool "mccmon6"
 	select MX6QDL
 	select SUPPORT_SPL
+	select DM
+	select DM_GPIO
+	select DM_ETH
+	select DM_SERIAL
+	select DM_I2C
+	select DM_SPI
+	imply CMD_DM
 
 config TARGET_MX6CUBOXI
 	bool "Solid-run mx6 boards"
diff --git a/board/liebherr/mccmon6/mccmon6.c b/board/liebherr/mccmon6/mccmon6.c
index 946b91f3a1..497095572e 100644
--- a/board/liebherr/mccmon6/mccmon6.c
+++ b/board/liebherr/mccmon6/mccmon6.c
@@ -12,17 +12,13 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/gpio.h>
 #include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/spi.h>
 #include <asm/mach-imx/boot_mode.h>
 #include <asm/io.h>
 #include <fsl_esdhc.h>
 #include <mmc.h>
 #include <netdev.h>
-#include <micrel.h>
 #include <phy.h>
 #include <input.h>
-#include <i2c.h>
 #include <spl.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -35,24 +31,11 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED |		\
-	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
-	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
 #define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |          \
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
 	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
 
 #define USDHC2_CD_GPIO		IMX_GPIO_NR(1, 4)
-#define ETH_PHY_RESET		IMX_GPIO_NR(1, 27)
-#define ECSPI3_CS0		IMX_GPIO_NR(4, 24)
-#define ECSPI3_FLWP		IMX_GPIO_NR(4, 27)
 #define NOR_WP			IMX_GPIO_NR(1, 1)
 #define DISPLAY_EN		IMX_GPIO_NR(1, 2)
 
@@ -93,45 +76,11 @@ static iomux_v3_cfg_t const usdhc3_pads[] = {
 	IOMUX_PADS(PAD_SD3_RST__SD3_RESET  | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 };
 
-static iomux_v3_cfg_t const enet_pads[] = {
-	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC    | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL
-		   | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK
-		   | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL
-		   | MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	/* KSZ9031 PHY Reset */
-	IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27  | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
 static void setup_iomux_uart(void)
 {
 	SETUP_IOMUX_PADS(uart1_pads);
 }
 
-static void setup_iomux_enet(void)
-{
-	SETUP_IOMUX_PADS(enet_pads);
-
-	/* Reset KSZ9031 PHY */
-	gpio_direction_output(ETH_PHY_RESET, 0);
-	mdelay(10);
-	gpio_set_value(ETH_PHY_RESET, 1);
-	udelay(100);
-}
-
 static struct fsl_esdhc_cfg usdhc_cfg[2] = {
 	{USDHC3_BASE_ADDR},
 	{USDHC2_BASE_ADDR},
@@ -273,74 +222,6 @@ static void setup_eimnor(void)
 	eimnor_cs_setup();
 }
 
-/* mccmon6 board has SPI Flash is connected to SPI3 */
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
-	return (bus == 2 && cs == 0) ? ECSPI3_CS0 : -1;
-}
-
-static iomux_v3_cfg_t const ecspi3_pads[] = {
-	/* SPI3 */
-	IOMUX_PADS(PAD_DISP0_DAT3__GPIO4_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-	IOMUX_PADS(PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
-	IOMUX_PADS(PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
-	IOMUX_PADS(PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
-};
-
-void setup_spi(void)
-{
-	SETUP_IOMUX_PADS(ecspi3_pads);
-
-	enable_spi_clk(true, 2);
-
-	/* set cs0 to high */
-	gpio_direction_output(ECSPI3_CS0, 1);
-
-	/* set flwp to high */
-	gpio_direction_output(ECSPI3_FLWP, 1);
-}
-
-struct i2c_pads_info mx6q_i2c1_pad_info = {
-	.scl = {
-		.i2c_mode = MX6Q_PAD_CSI0_DAT9__I2C1_SCL
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gpio_mode = MX6Q_PAD_CSI0_DAT9__GPIO5_IO27
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(5, 27)
-	},
-	.sda = {
-		.i2c_mode = MX6Q_PAD_CSI0_DAT8__I2C1_SDA
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gpio_mode = MX6Q_PAD_CSI0_DAT8__GPIO5_IO26
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(5, 26)
-	}
-};
-
-struct i2c_pads_info mx6q_i2c2_pad_info = {
-	.scl = {
-		.i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(4, 12)
-	},
-	.sda = {
-		.i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13
-			| MUX_PAD_CTRL(I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(4, 13)
-	}
-};
-
-int board_eth_init(bd_t *bis)
-{
-	setup_iomux_enet();
-
-	return cpu_eth_init(bis);
-}
-
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
@@ -356,10 +237,6 @@ int board_init(void)
 	gpio_direction_output(DISPLAY_EN, 1);
 
 	setup_eimnor();
-	setup_spi();
-
-	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c1_pad_info);
-	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c2_pad_info);
 
 	return 0;
 }
@@ -378,44 +255,6 @@ int checkboard(void)
 	return 0;
 }
 
-int board_phy_config(struct phy_device *phydev)
-{
-	/*
-	 * Default setting for GMII Clock Pad Skew Register 0x1EF:
-	 * MMD Address 0x2h, Register 0x8h
-	 *
-	 * GTX_CLK Pad Skew 0xF -> 0.9 nsec skew
-	 * RX_CLK Pad Skew 0xF -> 0.9 nsec skew
-	 *
-	 * Adjustment -> write 0x3FF:
-	 * GTX_CLK Pad Skew 0x1F -> 1.8 nsec skew
-	 * RX_CLK Pad Skew 0x1F -> 1.8 nsec skew
-	 *
-	 */
-	ksz9031_phy_extended_write(phydev, 0x2,
-				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x3FF);
-
-	ksz9031_phy_extended_write(phydev, 0x02,
-				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x00FF);
-
-	ksz9031_phy_extended_write(phydev, 0x2,
-				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC,
-				   0x3333);
-
-	ksz9031_phy_extended_write(phydev, 0x2,
-				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC,
-				   0x2052);
-
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
 #ifdef CONFIG_SPL_BOARD_INIT
 void spl_board_init(void)
 {
diff --git a/configs/mccmon6_nor_defconfig b/configs/mccmon6_nor_defconfig
index 18070cd0b1..93290fcbaf 100644
--- a/configs/mccmon6_nor_defconfig
+++ b/configs/mccmon6_nor_defconfig
@@ -9,24 +9,36 @@ CONFIG_SPL=y
 # CONFIG_CMD_BMODE is not set
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_NR_DRAM_BANKS=1
+CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/liebherr/mccmon6/mon6_imximage_nor.cfg"
 # CONFIG_USE_BOOTCOMMAND is not set
 CONFIG_BOUNCE_BUFFER=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_ENV_SUPPORT=y
 CONFIG_SPL_NOR_SUPPORT=y
+CONFIG_CMD_CLK=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+# CONFIG_CMD_PINMUX is not set
 CONFIG_CMD_SF=y
 CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
 CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nor0=8000000.nor"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=8000000.nor:32m@0x0(mccmon6-image.nor),256k@0x40000(u-boot-env.nor),1m@0x80000(u-boot.nor),8m@0x180000(kernel.nor),8m@0x980000(swupdate-kernel.nor),8m@0x1180000(swupdate-rootfs.nor),128k@0x1980000(kernel-dtb.nor),128k@0x19C0000(swupdate-kernel-dtb.nor)"
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-mccmon6"
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_DM=y
+CONFIG_CLK_IMX6Q=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_DM_MMC=y
 CONFIG_FSL_ESDHC=y
 CONFIG_MTD=y
 CONFIG_MTD_NOR_FLASH=y
@@ -36,13 +48,27 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_PROTECTION=y
 CONFIG_SYS_FLASH_CFI=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 CONFIG_SPI_FLASH_SPANSION=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
 CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
+# CONFIG_SPECIFY_CONSOLE_INDEX is not set
+# CONFIG_SPL_SERIAL_PRESENT is not set
+# CONFIG_TPL_SERIAL_PRESENT is not set
+CONFIG_MXC_UART=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_DM_THERMAL=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mccmon6_sd_defconfig b/configs/mccmon6_sd_defconfig
index d1d1313e1e..caa8ec70f9 100644
--- a/configs/mccmon6_sd_defconfig
+++ b/configs/mccmon6_sd_defconfig
@@ -10,24 +10,36 @@ CONFIG_SPL=y
 # CONFIG_CMD_BMODE is not set
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_NR_DRAM_BANKS=1
+CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/liebherr/mccmon6/mon6_imximage_sd.cfg"
 # CONFIG_USE_BOOTCOMMAND is not set
 CONFIG_BOUNCE_BUFFER=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_ENV_SUPPORT=y
 CONFIG_SPL_NOR_SUPPORT=y
+CONFIG_CMD_CLK=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+# CONFIG_CMD_PINMUX is not set
 CONFIG_CMD_SF=y
 CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
 CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nor0=8000000.nor"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=8000000.nor:32m@0x0(mccmon6-image.nor),256k@0x40000(u-boot-env.nor),1m@0x80000(u-boot.nor),8m@0x180000(kernel.nor),8m@0x980000(swupdate-kernel.nor),8m@0x1180000(swupdate-rootfs.nor),128k@0x1980000(kernel-dtb.nor),128k@0x19C0000(swupdate-kernel-dtb.nor)"
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-mccmon6"
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_DM=y
+CONFIG_CLK_IMX6Q=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_DM_MMC=y
 CONFIG_FSL_ESDHC=y
 CONFIG_MTD=y
 CONFIG_MTD_NOR_FLASH=y
@@ -37,13 +49,26 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_PROTECTION=y
 CONFIG_SYS_FLASH_CFI=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 CONFIG_SPI_FLASH_SPANSION=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
 CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
+# CONFIG_SPL_SERIAL_PRESENT is not set
+# CONFIG_TPL_SERIAL_PRESENT is not set
+CONFIG_MXC_UART=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_DM_THERMAL=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mccmon6.h b/include/configs/mccmon6.h
index 5ca9bc6848..f72d8cba2b 100644
--- a/include/configs/mccmon6.h
+++ b/include/configs/mccmon6.h
@@ -34,27 +34,12 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
 
-#define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT
-
-#define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE
 
 #define CONFIG_SYS_MEMTEST_START	0x10000000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
 
-#define CONFIG_SF_DEFAULT_BUS  2
-#define CONFIG_SF_DEFAULT_CS   0
-#define CONFIG_SF_DEFAULT_SPEED 25000000
-#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_SPEED		100000
-
 /* MMC Configuration */
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
@@ -71,10 +56,7 @@
 #define CONFIG_SYS_FLASH_BANKS_SIZES	{ (32 * SZ_1M) }
 
 /* Ethernet Configuration */
-#define CONFIG_FEC_MXC
 #define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_ETHPRIME			"FEC"
 #define CONFIG_FEC_MXC_PHYADDR		1
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
