diff mbox series

[U-Boot,v5,1/3] thermal: ti-bandgap: Add support for temperature sensor

Message ID 1510656153-26769-2-git-send-email-faiz_abbas@ti.com
State Accepted
Commit 8502f9f6d7781b5f461d7e3f7c958a45f64fdfa1
Delegated to: Tom Rini
Headers show
Series Support for TI bandgap temperature sensor | expand

Commit Message

Faiz Abbas Nov. 14, 2017, 10:42 a.m. UTC
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---

v5:
Added terminator brackets ({}) to ti_bandgap_match[]

v3:
Added Reviewed-by comment

v2:
 1. Removed extra elements from ti_bandgap
 2. Changed base address to ulong
 3. Changed to udev to dev to maintain consistency
 4. minor format changes

 common/spl/Kconfig                                 |   8 +
 .../thermal/ti_soc_thermal.txt                     |  35 ++++
 drivers/Makefile                                   |   1 +
 drivers/thermal/Kconfig                            |   6 +
 drivers/thermal/Makefile                           |   1 +
 drivers/thermal/ti-bandgap.c                       | 198 +++++++++++++++++++++
 6 files changed, 249 insertions(+)
 create mode 100644 doc/device-tree-bindings/thermal/ti_soc_thermal.txt
 create mode 100644 drivers/thermal/ti-bandgap.c

Comments

Lokesh Vutla Nov. 21, 2017, 12:40 p.m. UTC | #1
On Tuesday 21 November 2017 06:14 PM, Tom Rini wrote:
> On Tue, Nov 14, 2017 at 04:12:31PM +0530, Faiz Abbas wrote:
>> The dra7xx series of SOCs contain a temperature sensor and an
>> associated analog-to-digital converter (ADC) which produces
>> an output which is proportional to the SOC temperature.
>> Add support for this temperature sensor.
>>
>> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
>> Reviewed-by: Simon Glass <sjg@chromium.org>
>> ---
>>
>> v5:
>> Added terminator brackets ({}) to ti_bandgap_match[]
>>
>> v3:
>> Added Reviewed-by comment
>>
>> v2:
>>  1. Removed extra elements from ti_bandgap
>>  2. Changed base address to ulong
>>  3. Changed to udev to dev to maintain consistency
>>  4. minor format changes
>>
>>  common/spl/Kconfig                                 |   8 +
>>  .../thermal/ti_soc_thermal.txt                     |  35 ++++
>>  drivers/Makefile                                   |   1 +
>>  drivers/thermal/Kconfig                            |   6 +
>>  drivers/thermal/Makefile                           |   1 +
>>  drivers/thermal/ti-bandgap.c                       | 198 +++++++++++++++++++++
>>  6 files changed, 249 insertions(+)
>>  create mode 100644 doc/device-tree-bindings/thermal/ti_soc_thermal.txt
>>  create mode 100644 drivers/thermal/ti-bandgap.c
>>
> 
> This fails to build on am57xx_evm_nodt.  Lokesh, does it still make
> sense to have that defconfig?  If so, we need to disable this feature on
> that config, or we need to delete that config then apply this series.
> Thanks!
> 

Right, no point keeping am57xx_evm_nodt. We should delete this config
and apply this series.

Thanks and regards,
Lokesh
Tom Rini Nov. 21, 2017, 12:44 p.m. UTC | #2
On Tue, Nov 14, 2017 at 04:12:31PM +0530, Faiz Abbas wrote:
> The dra7xx series of SOCs contain a temperature sensor and an
> associated analog-to-digital converter (ADC) which produces
> an output which is proportional to the SOC temperature.
> Add support for this temperature sensor.
> 
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>
> ---
> 
> v5:
> Added terminator brackets ({}) to ti_bandgap_match[]
> 
> v3:
> Added Reviewed-by comment
> 
> v2:
>  1. Removed extra elements from ti_bandgap
>  2. Changed base address to ulong
>  3. Changed to udev to dev to maintain consistency
>  4. minor format changes
> 
>  common/spl/Kconfig                                 |   8 +
>  .../thermal/ti_soc_thermal.txt                     |  35 ++++
>  drivers/Makefile                                   |   1 +
>  drivers/thermal/Kconfig                            |   6 +
>  drivers/thermal/Makefile                           |   1 +
>  drivers/thermal/ti-bandgap.c                       | 198 +++++++++++++++++++++
>  6 files changed, 249 insertions(+)
>  create mode 100644 doc/device-tree-bindings/thermal/ti_soc_thermal.txt
>  create mode 100644 drivers/thermal/ti-bandgap.c
> 

This fails to build on am57xx_evm_nodt.  Lokesh, does it still make
sense to have that defconfig?  If so, we need to disable this feature on
that config, or we need to delete that config then apply this series.
Thanks!
Tom Rini Nov. 21, 2017, 12:46 p.m. UTC | #3
On Tue, Nov 21, 2017 at 06:10:59PM +0530, Lokesh Vutla wrote:
> 
> 
> On Tuesday 21 November 2017 06:14 PM, Tom Rini wrote:
> > On Tue, Nov 14, 2017 at 04:12:31PM +0530, Faiz Abbas wrote:
> >> The dra7xx series of SOCs contain a temperature sensor and an
> >> associated analog-to-digital converter (ADC) which produces
> >> an output which is proportional to the SOC temperature.
> >> Add support for this temperature sensor.
> >>
> >> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> >> Reviewed-by: Simon Glass <sjg@chromium.org>
> >> ---
> >>
> >> v5:
> >> Added terminator brackets ({}) to ti_bandgap_match[]
> >>
> >> v3:
> >> Added Reviewed-by comment
> >>
> >> v2:
> >>  1. Removed extra elements from ti_bandgap
> >>  2. Changed base address to ulong
> >>  3. Changed to udev to dev to maintain consistency
> >>  4. minor format changes
> >>
> >>  common/spl/Kconfig                                 |   8 +
> >>  .../thermal/ti_soc_thermal.txt                     |  35 ++++
> >>  drivers/Makefile                                   |   1 +
> >>  drivers/thermal/Kconfig                            |   6 +
> >>  drivers/thermal/Makefile                           |   1 +
> >>  drivers/thermal/ti-bandgap.c                       | 198 +++++++++++++++++++++
> >>  6 files changed, 249 insertions(+)
> >>  create mode 100644 doc/device-tree-bindings/thermal/ti_soc_thermal.txt
> >>  create mode 100644 drivers/thermal/ti-bandgap.c
> >>
> > 
> > This fails to build on am57xx_evm_nodt.  Lokesh, does it still make
> > sense to have that defconfig?  If so, we need to disable this feature on
> > that config, or we need to delete that config then apply this series.
> > Thanks!
> > 
> 
> Right, no point keeping am57xx_evm_nodt. We should delete this config
> and apply this series.

OK, I'll make it so, thanks!
Tom Rini Nov. 21, 2017, 1:06 p.m. UTC | #4
On Tue, Nov 14, 2017 at 04:12:31PM +0530, Faiz Abbas wrote:

> The dra7xx series of SOCs contain a temperature sensor and an
> associated analog-to-digital converter (ADC) which produces
> an output which is proportional to the SOC temperature.
> Add support for this temperature sensor.
> 
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>

Applied to u-boot/master, thanks!
diff mbox series

Patch

diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 0bd8370..0bf3ee3 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -604,6 +604,14 @@  config SPL_SPI_SUPPORT
 	  enable SPI drivers that are needed for other purposes also, such
 	  as a SPI PMIC.
 
+config SPL_THERMAL
+	bool "Driver support for thermal devices"
+	help
+	  Enable support for temperature-sensing devices. Some SoCs have on-chip
+	  temperature sensors to permit warnings, speed throttling or even
+	  automatic power-off when the temperature gets too high or low. Other
+	  devices may be discrete but connected on a suitable bus.
+
 config SPL_USB_HOST_SUPPORT
 	bool "Support USB host drivers"
 	help
diff --git a/doc/device-tree-bindings/thermal/ti_soc_thermal.txt b/doc/device-tree-bindings/thermal/ti_soc_thermal.txt
new file mode 100644
index 0000000..b4e88c2
--- /dev/null
+++ b/doc/device-tree-bindings/thermal/ti_soc_thermal.txt
@@ -0,0 +1,35 @@ 
+* Texas Instrument dra7xx SCM bandgap bindings
+
+In the System Control Module, SoC supplies a voltage reference
+and a temperature sensor feature that are gathered in the band
+gap voltage and temperature sensor (VBGAPTS) module. The band
+gap provides current and voltage reference for its internal
+circuits and other analog IP blocks. The analog-to-digital
+converter (ADC) produces an output value that is proportional
+to the silicon temperature.
+
+Required properties:
+- compatible : Should be:
+  - "ti,dra752-bandgap"
+- interrupts : this entry should indicate which interrupt line
+the talert signal is routed to;
+- regs : this is specific to each bandgap version, because
+the mapping may change from soc to soc, apart from depending
+on available features.
+
+Optional:
+- gpios : this entry should be used to inform which GPIO
+line the tshut signal is routed to. The informed GPIO will
+be treated as an IRQ;
+
+Example:
+bandgap {
+	reg = <0x4a0021e0 0xc
+		0x4a00232c 0xc
+		0x4a002380 0x2c
+		0x4a0023C0 0x3c
+		0x4a002564 0x8
+		0x4a002574 0x50>;
+	compatible = "ti,dra752-bandgap";
+	interrupts = <0 126 4>; /* talert */
+};
diff --git a/drivers/Makefile b/drivers/Makefile
index dab5c18..e6062a5 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -50,6 +50,7 @@  obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
 obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
 obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
 obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/
+obj-$(CONFIG_SPL_THERMAL) += thermal/
 
 endif
 endif
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 886f5fa..a71b9be 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -17,4 +17,10 @@  config IMX_THERMAL
           cpufreq is used as the cooling device to throttle CPUs when the
           passive trip is crossed.
 
+config TI_DRA7_THERMAL
+        bool "Temperature sensor driver for TI dra7xx SOCs"
+        help
+	 Enable thermal support for for the Texas Instruments DRA752 SoC family.
+	 The driver supports reading CPU temperature.
+
 endif # if DM_THERMAL
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index d768f5e..f6271a5 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -7,3 +7,4 @@ 
 
 obj-$(CONFIG_DM_THERMAL) += thermal-uclass.o
 obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
+obj-$(CONFIG_TI_DRA7_THERMAL) += ti-bandgap.o
diff --git a/drivers/thermal/ti-bandgap.c b/drivers/thermal/ti-bandgap.c
new file mode 100644
index 0000000..b490391
--- /dev/null
+++ b/drivers/thermal/ti-bandgap.c
@@ -0,0 +1,198 @@ 
+/*
+ * TI Bandgap temperature sensor driver
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * Taken from Linux v4.9 (drivers/thermal/ti-soc-thermal/ti-bandgap.c)
+ * and ported to uboot.
+ *
+ */
+
+#include <asm/io.h>
+#include <dm.h>
+#include <thermal.h>
+
+#define CTRL_CORE_TEMP_SENSOR_MPU	0
+#define DRA752_ADC_START_VALUE		540
+
+struct ti_bandgap {
+	ulong			base;
+	int			temperature;	/* in mili degree celsius */
+};
+
+/*
+ * DRA752 : Temperature values in milli degree celsius
+ * ADC code values from 540 to 945
+ */
+static int dra752_adc_to_temp[] = {
+	/* Index 540 - 549 */
+	-40000, -40000, -40000, -40000, -39800, -39400, -39000, -38600, -38200,
+	-37800,
+	/* Index 550 - 559 */
+	-37400, -37000, -36600, -36200, -35800, -35300, -34700, -34200, -33800,
+	-33400,
+	/* Index 560 - 569 */
+	-33000, -32600, -32200, -31800, -31400, -31000, -30600, -30200, -29800,
+	-29400,
+	/* Index 570 - 579 */
+	-29000, -28600, -28200, -27700, -27100, -26600, -26200, -25800, -25400,
+	-25000,
+	/* Index 580 - 589 */
+	-24600, -24200, -23800, -23400, -23000, -22600, -22200, -21800, -21400,
+	-21000,
+	/* Index 590 - 599 */
+	-20500, -19900, -19400, -19000, -18600, -18200, -17800, -17400, -17000,
+	-16600,
+	/* Index 600 - 609 */
+	-16200, -15800, -15400, -15000, -14600, -14200, -13800, -13400, -13000,
+	-12500,
+	/* Index 610 - 619 */
+	-11900, -11400, -11000, -10600, -10200, -9800, -9400, -9000, -8600,
+	-8200,
+	/* Index 620 - 629 */
+	-7800, -7400, -7000, -6600, -6200, -5800, -5400, -5000, -4500,
+	-3900,
+	/* Index 630 - 639 */
+	-3400, -3000, -2600, -2200, -1800, -1400, -1000, -600, -200,
+	200,
+	/* Index 640 - 649 */
+	600, 1000, 1400, 1800, 2200, 2600, 3000, 3400, 3900,
+	4500,
+	/* Index 650 - 659 */
+	5000, 5400, 5800, 6200, 6600, 7000, 7400, 7800, 8200,
+	8600,
+	/* Index 660 - 669 */
+	9000, 9400, 9800, 10200, 10600, 11000, 11400, 11800, 12200,
+	12700,
+	/* Index 670 - 679 */
+	13300, 13800, 14200, 14600, 15000, 15400, 15800, 16200, 16600,
+	17000,
+	/* Index 680 - 689 */
+	17400, 17800, 18200, 18600, 19000, 19400, 19800, 20200, 20600,
+	21000,
+	/* Index 690 - 699 */
+	21400, 21900, 22500, 23000, 23400, 23800, 24200, 24600, 25000,
+	25400,
+	/* Index 700 - 709 */
+	25800, 26200, 26600, 27000, 27400, 27800, 28200, 28600, 29000,
+	29400,
+	/* Index 710 - 719 */
+	29800, 30200, 30600, 31000, 31400, 31900, 32500, 33000, 33400,
+	33800,
+	/* Index 720 - 729 */
+	34200, 34600, 35000, 35400, 35800, 36200, 36600, 37000, 37400,
+	37800,
+	/* Index 730 - 739 */
+	38200, 38600, 39000, 39400, 39800, 40200, 40600, 41000, 41400,
+	41800,
+	/* Index 740 - 749 */
+	42200, 42600, 43100, 43700, 44200, 44600, 45000, 45400, 45800,
+	46200,
+	/* Index 750 - 759 */
+	46600, 47000, 47400, 47800, 48200, 48600, 49000, 49400, 49800,
+	50200,
+	/* Index 760 - 769 */
+	50600, 51000, 51400, 51800, 52200, 52600, 53000, 53400, 53800,
+	54200,
+	/* Index 770 - 779 */
+	54600, 55000, 55400, 55900, 56500, 57000, 57400, 57800, 58200,
+	58600,
+	/* Index 780 - 789 */
+	59000, 59400, 59800, 60200, 60600, 61000, 61400, 61800, 62200,
+	62600,
+	/* Index 790 - 799 */
+	63000, 63400, 63800, 64200, 64600, 65000, 65400, 65800, 66200,
+	66600,
+	/* Index 800 - 809 */
+	67000, 67400, 67800, 68200, 68600, 69000, 69400, 69800, 70200,
+	70600,
+	/* Index 810 - 819 */
+	71000, 71500, 72100, 72600, 73000, 73400, 73800, 74200, 74600,
+	75000,
+	/* Index 820 - 829 */
+	75400, 75800, 76200, 76600, 77000, 77400, 77800, 78200, 78600,
+	79000,
+	/* Index 830 - 839 */
+	79400, 79800, 80200, 80600, 81000, 81400, 81800, 82200, 82600,
+	83000,
+	/* Index 840 - 849 */
+	83400, 83800, 84200, 84600, 85000, 85400, 85800, 86200, 86600,
+	87000,
+	/* Index 850 - 859 */
+	87400, 87800, 88200, 88600, 89000, 89400, 89800, 90200, 90600,
+	91000,
+	/* Index 860 - 869 */
+	91400, 91800, 92200, 92600, 93000, 93400, 93800, 94200, 94600,
+	95000,
+	/* Index 870 - 879 */
+	95400, 95800, 96200, 96600, 97000, 97500, 98100, 98600, 99000,
+	99400,
+	/* Index 880 - 889 */
+	99800, 100200, 100600, 101000, 101400, 101800, 102200, 102600, 103000,
+	103400,
+	/* Index 890 - 899 */
+	103800, 104200, 104600, 105000, 105400, 105800, 106200, 106600, 107000,
+	107400,
+	/* Index 900 - 909 */
+	107800, 108200, 108600, 109000, 109400, 109800, 110200, 110600, 111000,
+	111400,
+	/* Index 910 - 919 */
+	111800, 112200, 112600, 113000, 113400, 113800, 114200, 114600, 115000,
+	115400,
+	/* Index 920 - 929 */
+	115800, 116200, 116600, 117000, 117400, 117800, 118200, 118600, 119000,
+	119400,
+	/* Index 930 - 939 */
+	119800, 120200, 120600, 121000, 121400, 121800, 122200, 122600, 123000,
+	123400,
+	/* Index 940 - 945 */
+	123800, 124200, 124600, 124900, 125000, 125000,
+};
+
+static int ti_bandgap_get_temp(struct udevice *dev,  int *temp)
+{
+	struct ti_bandgap *bgp = dev_get_priv(dev);
+
+	bgp->temperature = 0x3ff & readl(bgp->base + CTRL_CORE_TEMP_SENSOR_MPU);
+	*temp = dra752_adc_to_temp[bgp->temperature - DRA752_ADC_START_VALUE];
+
+	return 0;
+}
+
+static struct dm_thermal_ops ti_thermal_ops = {
+	.get_temp	= ti_bandgap_get_temp,
+};
+
+static int ti_bandgap_probe(struct udevice *dev)
+{
+	struct ti_bandgap *bgp = dev_get_priv(dev);
+
+	bgp->base = devfdt_get_addr_index(dev, 1);
+
+	return 0;
+}
+
+static const struct udevice_id of_ti_bandgap_match[] = {
+	{
+		.compatible = "ti,dra752-bandgap",
+	},
+	{},
+};
+
+U_BOOT_DRIVER(ti_bandgap_thermal) = {
+	.name	= "ti_bandgap_thermal",
+	.id	= UCLASS_THERMAL,
+	.ops	= &ti_thermal_ops,
+	.probe	= ti_bandgap_probe,
+	.of_match = of_ti_bandgap_match,
+	.priv_auto_alloc_size = sizeof(struct ti_bandgap),
+};