[U-Boot,v4,5/9] imx: Add error checking to setup_i2c()

Since this function can fail, check its return value.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
---

Changes in v4:
- Move SATA changes into the next patch

Changes in v3:
- Just warn when one of the board init stages fails

Changes in v2:
- Add new patch to add error checking to setup_i2c()

 arch/arm/imx-common/i2c-mxv7.c            | 24 +++++++++++++++----
 arch/arm/include/asm/imx-common/mxc_i2c.h |  4 ++--
 board/compulab/cm_fx6/cm_fx6.c            | 40 ++++++++++++++++++++++++++-----
 3 files changed, 55 insertions(+), 13 deletions(-)

On 1 October 2014 19:57, Simon Glass <sjg@chromium.org> wrote:
> Since this function can fail, check its return value.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
> ---
>
> Changes in v4:
> - Move SATA changes into the next patch

Applied to u-boot-dm/master.

>
> Changes in v3:
> - Just warn when one of the board init stages fails
>
> Changes in v2:
> - Add new patch to add error checking to setup_i2c()
>
>  arch/arm/imx-common/i2c-mxv7.c            | 24 +++++++++++++++----
>  arch/arm/include/asm/imx-common/mxc_i2c.h |  4 ++--
>  board/compulab/cm_fx6/cm_fx6.c            | 40 ++++++++++++++++++++++++++-----
>  3 files changed, 55 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm/imx-common/i2c-mxv7.c b/arch/arm/imx-common/i2c-mxv7.c
> index a580873..70cff5c 100644
> --- a/arch/arm/imx-common/i2c-mxv7.c
> +++ b/arch/arm/imx-common/i2c-mxv7.c
> @@ -69,15 +69,29 @@ static void * const i2c_bases[] = {
>  };
>
>  /* i2c_index can be from 0 - 2 */
> -void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> -               struct i2c_pads_info *p)
> +int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> +             struct i2c_pads_info *p)
>  {
> +       int ret;
> +
>         if (i2c_index >= ARRAY_SIZE(i2c_bases))
> -               return;
> +               return -EINVAL;
>         /* Enable i2c clock */
> -       enable_i2c_clk(1, i2c_index);
> +       ret = enable_i2c_clk(1, i2c_index);
> +       if (ret)
> +               goto err_clk;
> +
>         /* Make sure bus is idle */
> -       force_idle_bus(p);
> +       ret = force_idle_bus(p);
> +       if (ret)
> +               goto err_idle;
> +
>         bus_i2c_init(i2c_bases[i2c_index], speed, slave_addr,
>                         force_idle_bus, p);
> +
> +       return 0;
> +
> +err_idle:
> +err_clk:
> +       return ret;
>  }
> diff --git a/arch/arm/include/asm/imx-common/mxc_i2c.h b/arch/arm/include/asm/imx-common/mxc_i2c.h
> index 182c2f3..af86163 100644
> --- a/arch/arm/include/asm/imx-common/mxc_i2c.h
> +++ b/arch/arm/include/asm/imx-common/mxc_i2c.h
> @@ -52,8 +52,8 @@ struct i2c_pads_info {
>                                         &mx6q_##name : &mx6s_##name
>  #endif
>
> -void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> -               struct i2c_pads_info *p);
> +int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> +             struct i2c_pads_info *p);
>  void bus_i2c_init(void *base, int speed, int slave_addr,
>                 int (*idle_bus_fn)(void *p), void *p);
>  int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
> index fdb8ebf..9c6e686 100644
> --- a/board/compulab/cm_fx6/cm_fx6.c
> +++ b/board/compulab/cm_fx6/cm_fx6.c
> @@ -141,14 +141,36 @@ I2C_PADS(i2c2_pads,
>          IMX_GPIO_NR(1, 6));
>
>
> -static void cm_fx6_setup_i2c(void)
> +static int cm_fx6_setup_one_i2c(int busnum, struct i2c_pads_info *pads)
>  {
> -       setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c0_pads));
> -       setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c1_pads));
> -       setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c2_pads));
> +       int ret;
> +
> +       ret = setup_i2c(busnum, CONFIG_SYS_I2C_SPEED, 0x7f, pads);
> +       if (ret)
> +               printf("Warning: I2C%d setup failed: %d\n", busnum, ret);
> +
> +       return ret;
> +}
> +
> +static int cm_fx6_setup_i2c(void)
> +{
> +       int ret = 0, err;
> +
> +       /* i2c<x>_pads are wierd macro variables; we can't use an array */
> +       err = cm_fx6_setup_one_i2c(0, I2C_PADS_INFO(i2c0_pads));
> +       if (err)
> +               ret = err;
> +       err = cm_fx6_setup_one_i2c(1, I2C_PADS_INFO(i2c1_pads));
> +       if (err)
> +               ret = err;
> +       err = cm_fx6_setup_one_i2c(2, I2C_PADS_INFO(i2c2_pads));
> +       if (err)
> +               ret = err;
> +
> +       return ret;
>  }
>  #else
> -static void cm_fx6_setup_i2c(void) { }
> +static int cm_fx6_setup_i2c(void) { return 0; }
>  #endif
>
>  #ifdef CONFIG_USB_EHCI_MX6
> @@ -409,9 +431,15 @@ void ft_board_setup(void *blob, bd_t *bd)
>
>  int board_init(void)
>  {
> +       int ret;
> +
>         gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
>         cm_fx6_setup_gpmi_nand();
> -       cm_fx6_setup_i2c();
> +
> +       /* Warn on failure but do not abort boot */
> +       ret = cm_fx6_setup_i2c();
> +       if (ret)
> +               printf("Warning: I2C setup failed: %d\n", ret);
>
>         return 0;
>  }
> --
> 2.1.0.rc2.206.gedb03e5
>