@@ -79,7 +79,7 @@ int get_scl(void)
#define ZL30158_RST 8
-#define ZL30343_RST 9
+#define BFTIC4_RST 0
int board_early_init_f(void)
{
@@ -88,13 +88,15 @@ int board_early_init_f(void)
/* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
setbits_be32(&gur->ddrclkdr, 0x001f000f);
- /* take the Zarlinks out of reset as soon as possible */
- qrio_prst(ZL30158_RST, false, false);
- qrio_prst(ZL30343_RST, false, false);
+ /* set the BFTIC's prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and enable WD on it */
+ qrio_wdmask(BFTIC4_RST, true);
- /* and set their reset to power-up only */
- qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
- qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
+ /* set the ZL30138's prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and take it out of reset as soon as possible (needed for Hooper) */
+ qrio_prst(ZL30158_RST, false, false);
return 0;
}
@@ -127,16 +129,37 @@ unsigned long get_board_sys_clk(unsigned long dummy)
return 66666666;
}
+#define ETH_FRONT_PHY_RST 15
+#define QSFP2_RST 11
+#define QSFP1_RST 10
+#define ZL30343_RST 9
+
int misc_init_f(void)
{
/* configure QRIO pis for i2c deblocking */
i2c_deblock_gpio_cfg();
+ /* configure the front phy's prstcfg and take it out of reset */
+ qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prst(ETH_FRONT_PHY_RST, false, false);
+
+ /* set the ZL30343 prstcfg to reset at power-up and unit reset only */
+ qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_UNIT_RST);
+ /* and enable the WD on it */
+ qrio_wdmask(ZL30343_RST, true);
+
+ /* set the QSFPs' prstcfg to reset at power-up and unit rst only */
+ qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
+
+ /* and enable the WD on them */
+ qrio_wdmask(QSFP1_RST, true);
+ qrio_wdmask(QSFP2_RST, true);
+
return 0;
}
#define NUM_SRDS_BANKS 2
-#define PHY_RST 15
int misc_init_r(void)
{
@@ -157,9 +180,6 @@ int misc_init_r(void)
}
}
- /* take the mgmt eth phy out of reset */
- qrio_prst(PHY_RST, false, false);
-
return 0;
}
@@ -172,6 +192,7 @@ int hush_init_var(void)
#endif
#if defined(CONFIG_LAST_STAGE_INIT)
+
int last_stage_init(void)
{
#if defined(CONFIG_KMCOGE4)
@@ -187,6 +208,7 @@ int last_stage_init(void)
}
#endif
set_km_env();
+
return 0;
}
#endif
@@ -20,6 +20,7 @@ void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr);
#define PRSTCFG_POWUP_RST 0x3
void qrio_prst(u8 bit, bool en, bool wden);
+void qrio_wdmask(u8 bit, bool wden);
void qrio_prstcfg(u8 bit, u8 mode);
void qrio_set_leds(void);
void qrio_enable_app_buffer(void);
@@ -94,20 +94,23 @@ err_out:
}
#define PCIE_SW_RST 14
-#define PEXHC_SW_RST 13
-#define HOOPER_SW_RST 12
+#define PEXHC_RST 13
+#define HOOPER_RST 12
void pci_init_board(void)
{
- /* first wait for the PCIe FPGA to be configured
+ qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+
+ /* wait for the PCIe FPGA to be configured
* it has been triggered earlier in board_early_init_r */
- int ret = wait_for_fpga_config();
- if (ret)
+ if (wait_for_fpga_config())
printf("error finishing PCIe FPGA config\n");
qrio_prst(PCIE_SW_RST, false, false);
- qrio_prst(PEXHC_SW_RST, false, false);
- qrio_prst(HOOPER_SW_RST, false, false);
+ qrio_prst(PEXHC_RST, false, false);
+ qrio_prst(HOOPER_RST, false, false);
/* Hooper is not direcly PCIe capable */
mdelay(50);
@@ -91,7 +91,7 @@ void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val)
#define WDMASK_OFF 0x16
-static void qrio_wdmask(u8 bit, bool wden)
+void qrio_wdmask(u8 bit, bool wden)
{
u16 wdmask;
void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
This adds the reset support for the following devices that was until then not implemented: - BFTIC4 - QSFPs This also fixes the configuration of the prst behaviour for the other resets: Only the u-boot and kernel relevant subsystems are taken out of reset (pcie, ZL30158, and front eth phy). Most of the prst config move to misc_init_f(), except for the PCIe related ones that are in pci_init_board and the bftic and ZL30158 ones that should be done as soon as possible. Only the behavior of the Hooper reset is changed according to the documentation as the application is not able to not configure the switch when it is not reset. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> --- board/keymile/kmp204x/kmp204x.c | 44 ++++++++++++++++++++++++++++++----------- board/keymile/kmp204x/kmp204x.h | 1 + board/keymile/kmp204x/pci.c | 17 +++++++++------- board/keymile/kmp204x/qrio.c | 2 +- 4 files changed, 45 insertions(+), 19 deletions(-)