diff mbox

[U-Boot] da850: modifications for Logic PD Rev.3 AM18xx EVM

Message ID 1311870338-18950-8-git-send-email-nagabhushana.netagunte@ti.com
State Changes Requested
Headers show

Commit Message

nagabhushana.netagunte@ti.com July 28, 2011, 4:25 p.m. UTC 
From: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>

AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
---
 arch/arm/include/asm/arch-davinci/hardware.h |    5 ++++-
 board/davinci/da8xxevm/da850evm.c            |   15 +++++++++++++++
 2 files changed, 19 insertions(+), 1 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/include/asm/arch-davinci/hardware.h b/arch/arm/include/asm/arch-davinci/hardware.h
index c41d756..3d6cb88 100644
--- a/arch/arm/include/asm/arch-davinci/hardware.h
+++ b/arch/arm/include/asm/arch-davinci/hardware.h
@@ -157,7 +157,10 @@  typedef volatile unsigned int *	dv_reg_p;
 #define HOST1CFG				(DAVINCI_BOOTCFG_BASE + 0x44)
 #define PSC0_MDCTL				(DAVINCI_PSC0_BASE + 0xa00)
 
-
+#define GPIO_BANK0_REG_DIR_ADDR			(DAVINCI_GPIO_BASE + 0x10)
+#define GPIO_BANK0_REG_OPDATA_ADDR		(DAVINCI_GPIO_BASE + 0x14)
+#define GPIO_BANK0_REG_SET_ADDR			(DAVINCI_GPIO_BASE + 0x18)
+#define GPIO_BANK0_REG_CLR_ADDR			(DAVINCI_GPIO_BASE + 0x1c)
 #define GPIO_BANK2_REG_DIR_ADDR			(DAVINCI_GPIO_BASE + 0x38)
 #define GPIO_BANK2_REG_OPDATA_ADDR		(DAVINCI_GPIO_BASE + 0x3c)
 #define GPIO_BANK2_REG_SET_ADDR			(DAVINCI_GPIO_BASE + 0x40)
diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c
index fd05703..a077368 100644
--- a/board/davinci/da8xxevm/da850evm.c
+++ b/board/davinci/da8xxevm/da850evm.c
@@ -110,6 +110,8 @@  const struct pinmux_config nand_pins[] = {
 };
 #elif defined(CONFIG_SYS_USE_NOR)
 const struct pinmux_config nor_pins[] = {
+	/* GP0[11] is required for SD to work on Rev 3 EVMs */
+	{ pinmux(0), 8, 4 },	/* GP0[11] */
 	{ pinmux(5), 1, 6 },
 	{ pinmux(6), 1, 6 },
 	{ pinmux(7), 1, 0 },
@@ -229,6 +231,7 @@  u32 get_board_rev(void)
 
 int board_init(void)
 {
+	unsigned int val;
 #ifndef CONFIG_USE_IRQ
 	irq_init();
 #endif
@@ -276,6 +279,18 @@  int board_init(void)
 	if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
 		return 1;
 
+#ifdef CONFIG_SYS_USE_NOR
+	/* Set the GPIO direction as output */
+	val = REG(GPIO_BANK0_REG_DIR_ADDR);
+	val &= ~(0x01 << 11);
+	REG(GPIO_BANK0_REG_DIR_ADDR) = val;
+
+	/* Set the output as low */
+	val = REG(GPIO_BANK0_REG_SET_ADDR);
+	val |= (0x01 << 11);
+	REG(GPIO_BANK0_REG_CLR_ADDR) = val;
+#endif
+
 #ifdef CONFIG_DRIVER_TI_EMAC
 	if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0)
 		return 1;