diff mbox

[U-Boot,15/18] Blackfin: split out async setup

Message ID 1309289787-7846-16-git-send-email-vapier@gentoo.org
State Accepted
Commit 4150cec3353b7a6d7a3ea71b2d3c62deafff353d
Delegated to: Mike Frysinger
Headers show

Commit Message

Mike Frysinger June 28, 2011, 7:36 p.m. UTC
We really only need to tweak the async banks in the initcode if the
processor is booting out of it, otherwise we can wait until later
on in the CPU booting setup.

This also makes testing in the sim and early bring up over JTAG work
much smoother when the initcode gets bypassed.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/cpu/cpu.c      |   16 ++++++---
 arch/blackfin/cpu/initcode.c |   47 ++--------------------------
 arch/blackfin/cpu/initcode.h |   71 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 84 insertions(+), 50 deletions(-)
 create mode 100644 arch/blackfin/cpu/initcode.h
diff mbox

Patch

diff --git a/arch/blackfin/cpu/cpu.c b/arch/blackfin/cpu/cpu.c
index 18dbdf7..6a0bcca 100644
--- a/arch/blackfin/cpu/cpu.c
+++ b/arch/blackfin/cpu/cpu.c
@@ -19,6 +19,7 @@ 
 
 #include "cpu.h"
 #include "serial.h"
+#include "initcode.h"
 
 ulong bfin_poweron_retx;
 
@@ -44,13 +45,16 @@  void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)
 		extern char _sdata_l1[], _data_l1_lma[], _data_l1_len[];
 		memcpy(&_sdata_l1, &_data_l1_lma, (unsigned long)_data_l1_len);
 	}
-#if defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
-	/* The BF537 bootrom will reset the EBIU_AMGCTL register on us
-	 * after it has finished loading the LDR.  So configure it again.
+
+	/*
+	 * Make sure our async settings are committed.  Some bootroms
+	 * (like the BF537) will reset some registers on us after it
+	 * has finished loading the LDR.  Or if we're booting over
+	 * JTAG, the initcode never got a chance to run.  Or if we
+	 * aren't booting from parallel flash, the initcode skipped
+	 * this step completely.
 	 */
-	else
-		bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL);
-#endif
+	program_async_controller(NULL);
 
 	/* Save RETX so we can pass it while booting Linux */
 	bfin_poweron_retx = bootflag;
diff --git a/arch/blackfin/cpu/initcode.c b/arch/blackfin/cpu/initcode.c
index 61dc5ab..917b7f9 100644
--- a/arch/blackfin/cpu/initcode.c
+++ b/arch/blackfin/cpu/initcode.c
@@ -4,7 +4,7 @@ 
  * cannot make any function calls as it may be executed all by itself by
  * the Blackfin's bootrom in LDR format.
  *
- * Copyright (c) 2004-2008 Analog Devices Inc.
+ * Copyright (c) 2004-2011 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
  */
@@ -107,6 +107,8 @@  static inline void serial_putc(char c)
 		continue;
 }
 
+#include "initcode.h"
+
 __attribute__((always_inline)) static inline void
 program_nmi_handler(void)
 {
@@ -172,21 +174,6 @@  program_nmi_handler(void)
 # define CONFIG_PLL_CTL_VAL (SPORT_HYST | (CONFIG_VCO_MULT << 9) | CONFIG_CLKIN_HALF)
 #endif
 
-#ifndef CONFIG_EBIU_RSTCTL_VAL
-# define CONFIG_EBIU_RSTCTL_VAL 0 /* only MDDRENABLE is useful */
-#endif
-#if ((CONFIG_EBIU_RSTCTL_VAL & 0xFFFFFFC4) != 0)
-# error invalid EBIU_RSTCTL value: must not set reserved bits
-#endif
-
-#ifndef CONFIG_EBIU_MBSCTL_VAL
-# define CONFIG_EBIU_MBSCTL_VAL 0
-#endif
-
-#if defined(CONFIG_EBIU_DDRQUE_VAL) && ((CONFIG_EBIU_DDRQUE_VAL & 0xFFFF8000) != 0)
-# error invalid EBIU_DDRQUE value: must not set reserved bits
-#endif
-
 /* Make sure our voltage value is sane so we don't blow up! */
 #ifndef CONFIG_VR_CTL_VAL
 # define BFIN_CCLK ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_CCLK_DIV)
@@ -642,34 +629,6 @@  check_hibernation(ADI_BOOT_DATA *bs, u16 vr_ctl, bool put_into_srfs)
 	serial_putc('e');
 }
 
-__attribute__((always_inline)) static inline void
-program_async_controller(ADI_BOOT_DATA *bs)
-{
-	serial_putc('a');
-
-	/* Program the async banks controller. */
-	bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL);
-	bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL);
-	bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL);
-
-	serial_putc('b');
-
-	/* Not all parts have these additional MMRs. */
-#ifdef EBIU_MBSCTL
-	bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL);
-#endif
-#ifdef EBIU_MODE
-# ifdef CONFIG_EBIU_MODE_VAL
-	bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL);
-# endif
-# ifdef CONFIG_EBIU_FCTL_VAL
-	bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL);
-# endif
-#endif
-
-	serial_putc('c');
-}
-
 BOOTROM_CALLED_FUNC_ATTR
 void initcode(ADI_BOOT_DATA *bs)
 {
diff --git a/arch/blackfin/cpu/initcode.h b/arch/blackfin/cpu/initcode.h
new file mode 100644
index 0000000..e0aad6d
--- /dev/null
+++ b/arch/blackfin/cpu/initcode.h
@@ -0,0 +1,71 @@ 
+/*
+ * Code for early processor initialization
+ *
+ * Copyright (c) 2004-2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __BFIN_INITCODE_H__
+#define __BFIN_INITCODE_H__
+
+#include <asm/mach-common/bits/bootrom.h>
+
+#ifndef BFIN_IN_INITCODE
+# define serial_putc(c)
+#endif
+
+#ifndef CONFIG_EBIU_RSTCTL_VAL
+# define CONFIG_EBIU_RSTCTL_VAL 0 /* only MDDRENABLE is useful */
+#endif
+#if ((CONFIG_EBIU_RSTCTL_VAL & 0xFFFFFFC4) != 0)
+# error invalid EBIU_RSTCTL value: must not set reserved bits
+#endif
+
+#ifndef CONFIG_EBIU_MBSCTL_VAL
+# define CONFIG_EBIU_MBSCTL_VAL 0
+#endif
+
+#if defined(CONFIG_EBIU_DDRQUE_VAL) && ((CONFIG_EBIU_DDRQUE_VAL & 0xFFFF8000) != 0)
+# error invalid EBIU_DDRQUE value: must not set reserved bits
+#endif
+
+__attribute__((always_inline)) static inline void
+program_async_controller(ADI_BOOT_DATA *bs)
+{
+#ifdef BFIN_IN_INITCODE
+	/*
+	 * We really only need to setup the async banks early if we're
+	 * booting out of it.  Otherwise, do it later on in cpu_init.
+	 */
+	if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS &&
+	    CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_PARA)
+		return;
+#endif
+
+	serial_putc('a');
+
+	/* Program the async banks controller. */
+	bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL);
+	bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL);
+	bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL);
+
+	serial_putc('b');
+
+	/* Not all parts have these additional MMRs. */
+#ifdef EBIU_MBSCTL
+	bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL);
+#endif
+#ifdef EBIU_MODE
+# ifdef CONFIG_EBIU_MODE_VAL
+	bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL);
+# endif
+# ifdef CONFIG_EBIU_FCTL_VAL
+	bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL);
+# endif
+#endif
+
+	serial_putc('c');
+}
+
+#endif