Show patches with: Submitter = Dave Klotz       |    State = Action Required       |    Archived = No       |   27 patches
Patch Series A/F/R/T S/W/F Date Submitter Delegate State
[v2,2/2] usb: dwc3: generic: add SpacemiT K1 support usb: add K1 USB2 PHY and generic DWC3 support - - - - --- 2026-10-06 Dave Klotz marex New
[v2,1/2] phy: spacemit: add K1 USB 2.0 PHY driver usb: add K1 USB2 PHY and generic DWC3 support - - - - --- 2026-10-06 Dave Klotz marex New
[v2,3/3] mmc: k1: do not release the shared AXI clock and reset on probe failure mmc: k1: fixes for the SpacemiT K1 SDHCI driver - - 1 - --- 2026-10-05 Dave Klotz freenix New
[v2,2/3] mmc: k1: let the SPL read SD cards more than one block at a time mmc: k1: fixes for the SpacemiT K1 SDHCI driver - - 1 - --- 2026-10-05 Dave Klotz freenix New
[v2,1/3] mmc: k1: handle a missing max-frequency and clk_set_rate()'s return value mmc: k1: fixes for the SpacemiT K1 SDHCI driver - - 1 - --- 2026-10-05 Dave Klotz freenix New
[v3] clk: spacemit: program the mux when setting a mix clock's rate [v3] clk: spacemit: program the mux when setting a mix clock's rate - - 1 - --- 2026-10-05 Dave Klotz tim609 Under Review
riscv: spacemit: handle overlapping DDR firmware relocation riscv: spacemit: handle overlapping DDR firmware relocation - - - - --- 2026-10-05 Dave Klotz tim609 New
[RESEND,2/2] spacemit: k1: fall back to the other boot devices in SPL spacemit: k1: SPL robustness for boards without a PMIC or SPI NOR - - - - --- 2026-10-02 Dave Klotz tim609 New
[RESEND,1/2] spacemit: k1: do not require a PMIC or an SPI controller in SPL spacemit: k1: SPL robustness for boards without a PMIC or SPI NOR - - - - --- 2026-10-02 Dave Klotz tim609 New
[2/2] spacemit: k1: fall back to the other boot devices in SPL Untitled series #526339 - - - - --- 2026-10-02 Dave Klotz tim609 New
[1/2] spacemit: k1: do not require a PMIC or an SPI controller in SPL [1/2] spacemit: k1: do not require a PMIC or an SPI controller in SPL - - - - --- 2026-10-02 Dave Klotz tim609 New
[9/9] pci: spacemit: do not fail the probe when the link is down pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[8/9] pci: spacemit: set the link width from num-lanes pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[7/9] pci: spacemit: do not advertise ASPM L1 pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[6/9] pci: spacemit: do not force the link to 2.5 GT/s pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[5/9] pci: spacemit: report link up from the link status register pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[4/9] pci: spacemit: check clock, reset and iATU setup results pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[3/9] pci: spacemit: soft reset the controller before bring-up pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[2/9] pci: spacemit: hold the PHY interface in reset until link start pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[1/9] pci: spacemit: power the slot from vpcie3v3-supply pci: spacemit: fixes for the K1 PCIe host driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[7/7] phy: spacemit: k1: power on the combo PHY in USB 3 mode phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[6/7] phy: spacemit: k1: don't overwrite whole PLL control registers phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[5/7] phy: spacemit: k1: set CLKSEL on every lane phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[4/7] phy: spacemit: k1: program the termination fields properly phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[3/7] phy: spacemit: k1: restore port A state after calibration phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[2/7] phy: spacemit: k1: don't start the combo PHY PLL to calibrate phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New
[1/7] phy: spacemit: k1: enable refclk and deassert the PHY reset at probe phy: spacemit: k1: fix the PCIe and combo PHY driver - - - - --- 2026-10-02 Dave Klotz tim609 New