Message ID | 1505460876-7303-9-git-send-email-akshay.adiga@linux.vnet.ibm.com |
---|---|
State | Superseded |
Headers | show |
Series | Enable stop4 idle state | expand |
* Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> [2017-09-15 13:04:36]: > Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> > --- > doc/opal-api/opal-slw-set-reg-100.rst | 46 +++++++++++++++++++++++++++++++++++ > 1 file changed, 46 insertions(+) > create mode 100644 doc/opal-api/opal-slw-set-reg-100.rst > > diff --git a/doc/opal-api/opal-slw-set-reg-100.rst b/doc/opal-api/opal-slw-set-reg-100.rst > new file mode 100644 > index 0000000..64ecdee > --- /dev/null > +++ b/doc/opal-api/opal-slw-set-reg-100.rst > @@ -0,0 +1,46 @@ > +OPAL_SLW_SET_REG > +============================== > +:: > + > + int64_t opal_slw_set_reg(uint64_t cpu_pir, uint64_t sprn, uint64_t val) > + > + > +OPAL_SLW_SET_REG is used to inform low-level firmware to restore a > +given value of SPR when there is a state loss. The actual set of SPR > +that is supported is platform dependent. > + > + > +In Power 8, it uses p8_pore_gen_cpufreq_fixed(), api provided by pore engine, > +to inform the spr with their corresponding values with which they > +must be restored. > + > + > +In Power 9, it uses p9_stop_save_cpureg(), api provided by self restore code, > +to inform the spr with their corresponding values with which they > +must be restored. > + > + > +Parameters > +---------- > + > +``uint64_t cpu_pir`` > +This parameter specifies the pir of the cpu for which the call is being made. > + > +``uint64_t sprn`` > +This parameter specifies the spr number as mentioned in p9_stop_api.H for > +Power9 and p8_pore_table_gen_api.H for Power8. > + > +``uint64_t val`` > +This parameter specifices value with which the spr should be restored. > + > +Returns > +------- > + > +``OPAL_INTERNAL_ERROR`` > +On failure. The actual error code from the platform specific code is logged in the OPAL logs > + > +``OPAL_UNSUPPORTED`` > +In power8 only, if spr restore is not supported by pore engine. If the low-level firmware does not support this feature or the given SPR is not supported by the pore engine or stop api. > + > +``OPAL_SUCCESS`` > +On success > -- > 2.5.5 >
diff --git a/doc/opal-api/opal-slw-set-reg-100.rst b/doc/opal-api/opal-slw-set-reg-100.rst new file mode 100644 index 0000000..64ecdee --- /dev/null +++ b/doc/opal-api/opal-slw-set-reg-100.rst @@ -0,0 +1,46 @@ +OPAL_SLW_SET_REG +============================== +:: + + int64_t opal_slw_set_reg(uint64_t cpu_pir, uint64_t sprn, uint64_t val) + + +OPAL_SLW_SET_REG is used to inform low-level firmware to restore a +given value of SPR when there is a state loss. The actual set of SPR +that is supported is platform dependent. + + +In Power 8, it uses p8_pore_gen_cpufreq_fixed(), api provided by pore engine, +to inform the spr with their corresponding values with which they +must be restored. + + +In Power 9, it uses p9_stop_save_cpureg(), api provided by self restore code, +to inform the spr with their corresponding values with which they +must be restored. + + +Parameters +---------- + +``uint64_t cpu_pir`` +This parameter specifies the pir of the cpu for which the call is being made. + +``uint64_t sprn`` +This parameter specifies the spr number as mentioned in p9_stop_api.H for +Power9 and p8_pore_table_gen_api.H for Power8. + +``uint64_t val`` +This parameter specifices value with which the spr should be restored. + +Returns +------- + +``OPAL_INTERNAL_ERROR`` +On failure. The actual error code from the platform specific code is logged in the OPAL logs + +``OPAL_UNSUPPORTED`` +In power8 only, if spr restore is not supported by pore engine. + +``OPAL_SUCCESS`` +On success
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> --- doc/opal-api/opal-slw-set-reg-100.rst | 46 +++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) create mode 100644 doc/opal-api/opal-slw-set-reg-100.rst