diff mbox series

[v4,2/5] ppc/pnv: Extend SPI model

Message ID 20240617165419.8388-3-chalapathi.v@linux.ibm.com
State New
Headers show
Series hw/ppc: SPI model | expand

Commit Message

Chalapathi V June 17, 2024, 4:54 p.m. UTC
In this commit SPI shift engine and sequencer logic is implemented.
Shift engine performs serialization and de-serialization according to the
control by the sequencer and according to the setup defined in the
configuration registers. Sequencer implements the main control logic and
FSM to handle data transmit and data receive control of the shift engine.

Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
---
 include/hw/ssi/pnv_spi.h |   27 +
 hw/ssi/pnv_spi.c         | 1039 ++++++++++++++++++++++++++++++++++++++
 hw/ssi/trace-events      |   15 +
 3 files changed, 1081 insertions(+)

Comments

Cédric Le Goater June 18, 2024, 4:06 p.m. UTC | #1
On 6/17/24 6:54 PM, Chalapathi V wrote:
> In this commit SPI shift engine and sequencer logic is implemented.
> Shift engine performs serialization and de-serialization according to the
> control by the sequencer and according to the setup defined in the
> configuration registers. Sequencer implements the main control logic and
> FSM to handle data transmit and data receive control of the shift engine.
> 
> Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>

I didn't see anything fundamentally wrong but I lack the knowledge
on this HW unit (and the time) to say I did a review. May be other
team mates can ?


Thanks,

C.




> ---
>   include/hw/ssi/pnv_spi.h |   27 +
>   hw/ssi/pnv_spi.c         | 1039 ++++++++++++++++++++++++++++++++++++++
>   hw/ssi/trace-events      |   15 +
>   3 files changed, 1081 insertions(+)
> 
> diff --git a/include/hw/ssi/pnv_spi.h b/include/hw/ssi/pnv_spi.h
> index 71c53d4a17..21fbfcb69c 100644
> --- a/include/hw/ssi/pnv_spi.h
> +++ b/include/hw/ssi/pnv_spi.h
> @@ -8,6 +8,14 @@
>    * This model Supports a connection to a single SPI responder.
>    * Introduced for P10 to provide access to SPI seeproms, TPM, flash device
>    * and an ADC controller.
> + *
> + * All SPI function control is mapped into the SPI register space to enable
> + * full control by firmware.
> + *
> + * SPI Controller has sequencer and shift engine. The SPI shift engine
> + * performs serialization and de-serialization according to the control by
> + * the sequencer and according to the setup defined in the configuration
> + * registers and the SPI sequencer implements the main control logic.
>    */
>   #include "hw/ssi/ssi.h"
>   #include "hw/sysbus.h"
> @@ -50,6 +58,25 @@ typedef struct PnvSpi {
>       MemoryRegion    xscom_spic_regs;
>       /* SPI object number */
>       uint32_t        spic_num;
> +    uint8_t         transfer_len;
> +    uint8_t         responder_select;
> +    /* To verify if shift_n1 happens prior to shift_n2 */
> +    bool            shift_n1_done;
> +    /* Loop counter for branch operation opcode Ex/Fx */
> +    uint8_t         loop_counter_1;
> +    uint8_t         loop_counter_2;
> +    /* N1/N2_bits specifies the size of the N1/N2 segment of a frame in bits.*/
> +    uint8_t         N1_bits;
> +    uint8_t         N2_bits;
> +    /* Number of bytes in a payload for the N1/N2 frame segment.*/
> +    uint8_t         N1_bytes;
> +    uint8_t         N2_bytes;
> +    /* Number of N1/N2 bytes marked for transmit */
> +    uint8_t         N1_tx;
> +    uint8_t         N2_tx;
> +    /* Number of N1/N2 bytes marked for receive */
> +    uint8_t         N1_rx;
> +    uint8_t         N2_rx;
>   
>       /* SPI registers */
>       uint64_t        regs[PNV_SPI_REGS];
> diff --git a/hw/ssi/pnv_spi.c b/hw/ssi/pnv_spi.c
> index da9e3925dd..b8f4370525 100644
> --- a/hw/ssi/pnv_spi.c
> +++ b/hw/ssi/pnv_spi.c
> @@ -14,9 +14,1040 @@
>   #include "hw/ssi/pnv_spi_regs.h"
>   #include "hw/ssi/ssi.h"
>   #include <libfdt.h>
> +#include <math.h>
>   #include "hw/irq.h"
>   #include "trace.h"
>   
> +/* PnvXferBuffer */
> +typedef struct PnvXferBuffer {
> +
> +    uint32_t    len;
> +    uint8_t    *data;
> +
> +} PnvXferBuffer;
> +
> +/* pnv_spi_xfer_buffer_methods */
> +static PnvXferBuffer *pnv_spi_xfer_buffer_new(void)
> +{
> +    PnvXferBuffer *payload = g_malloc0(sizeof(*payload));
> +
> +    return payload;
> +}
> +
> +static void pnv_spi_xfer_buffer_free(PnvXferBuffer *payload)
> +{
> +    free(payload->data);
> +    free(payload);
> +}
> +
> +static uint8_t *pnv_spi_xfer_buffer_write_ptr(PnvXferBuffer *payload,
> +                uint32_t offset, uint32_t length)
> +{
> +    if (payload->len < (offset + length)) {
> +        payload->len = offset + length;
> +        payload->data = g_realloc(payload->data, payload->len);
> +    }
> +    return &payload->data[offset];
> +}
> +
> +static bool does_rdr_match(PnvSpi *s)
> +{
> +    /*
> +     * According to spec, the mask bits that are 0 are compared and the
> +     * bits that are 1 are ignored.
> +     */
> +    uint16_t rdr_match_mask = GETFIELD(SPI_MM_RDR_MATCH_MASK,
> +                                        s->regs[SPI_MM_REG]);
> +    uint16_t rdr_match_val = GETFIELD(SPI_MM_RDR_MATCH_VAL,
> +                                        s->regs[SPI_MM_REG]);
> +
> +    if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) &
> +            GETFIELD(PPC_BITMASK(48, 63), s->regs[SPI_RCV_DATA_REG]))) {
> +        return true;
> +    }
> +    return false;
> +}
> +
> +static uint8_t get_from_offset(PnvSpi *s, uint8_t offset)
> +{
> +    uint8_t byte;
> +
> +    /*
> +     * Offset is an index between 0 and PNV_SPI_REG_SIZE - 1
> +     * Check the offset before using it.
> +     */
> +    if (offset < PNV_SPI_REG_SIZE) {
> +        byte = (s->regs[SPI_XMIT_DATA_REG] >> (56 - offset * 8)) & 0xFF;
> +    } else {
> +        /*
> +         * Log an error and return a 0xFF since we have to assign something
> +         * to byte before returning.
> +         */
> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to get byte "
> +                      "from TDR\n", offset);
> +        byte = 0xff;
> +    }
> +    return byte;
> +}
> +
> +static uint8_t read_from_frame(PnvSpi *s, uint8_t *read_buf, uint8_t nr_bytes,
> +                uint8_t ecc_count, uint8_t shift_in_count)
> +{
> +    uint8_t byte;
> +    int count = 0;
> +
> +    while (count < nr_bytes) {
> +        shift_in_count++;
> +        if ((ecc_count != 0) &&
> +            (shift_in_count == (PNV_SPI_REG_SIZE + ecc_count))) {
> +            shift_in_count = 0;
> +        } else {
> +            byte = read_buf[count];
> +            trace_pnv_spi_shift_rx(byte, count);
> +            s->regs[SPI_RCV_DATA_REG] = (s->regs[SPI_RCV_DATA_REG] << 8) | byte;
> +        }
> +        count++;
> +    } /* end of while */
> +    return shift_in_count;
> +}
> +
> +static void spi_response(PnvSpi *s, int bits, PnvXferBuffer *rsp_payload)
> +{
> +    uint8_t ecc_count;
> +    uint8_t shift_in_count;
> +
> +    /*
> +     * Processing here must handle:
> +     * - Which bytes in the payload we should move to the RDR
> +     * - Explicit mode counter configuration settings
> +     * - RDR full and RDR overrun status
> +     */
> +
> +    /*
> +     * First check that the response payload is the exact same
> +     * number of bytes as the request payload was
> +     */
> +    if (rsp_payload->len != (s->N1_bytes + s->N2_bytes)) {
> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload size in "
> +                       "bytes, expected %d, got %d\n",
> +                       (s->N1_bytes + s->N2_bytes), rsp_payload->len);
> +    } else {
> +        uint8_t ecc_control;
> +        trace_pnv_spi_rx_received(rsp_payload->len);
> +        trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                        s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
> +        /*
> +         * Adding an ECC count let's us know when we have found a payload byte
> +         * that was shifted in but cannot be loaded into RDR.  Bits 29-30 of
> +         * clock_config_reset_control register equal to either 0b00 or 0b10
> +         * indicate that we are taking in data with ECC and either applying
> +         * the ECC or discarding it.
> +         */
> +        ecc_count = 0;
> +        ecc_control = GETFIELD(PPC_BITMASK(29, 30), s->regs[SPI_CLK_CFG_REG]);
> +        if (ecc_control == 0 || ecc_control == 2) {
> +            ecc_count = 1;
> +        }
> +        /*
> +         * Use the N1_rx and N2_rx counts to control shifting data from the
> +         * payload into the RDR.  Keep an overall count of the number of bytes
> +         * shifted into RDR so we can discard every 9th byte when ECC is
> +         * enabled.
> +         */
> +        shift_in_count = 0;
> +        /* Handle the N1 portion of the frame first */
> +        if (s->N1_rx != 0) {
> +            trace_pnv_spi_rx_read_N1frame();
> +            shift_in_count = read_from_frame(s, &rsp_payload->data[0],
> +                            s->N1_bytes, ecc_count, shift_in_count);
> +        }
> +        /* Handle the N2 portion of the frame */
> +        if (s->N2_rx != 0) {
> +            trace_pnv_spi_rx_read_N2frame();
> +            shift_in_count = read_from_frame(s,
> +                            &rsp_payload->data[s->N1_bytes], s->N2_bytes,
> +                            ecc_count, shift_in_count);
> +        }
> +        if ((s->N1_rx + s->N2_rx) > 0) {
> +            /*
> +             * Data was received so handle RDR status.
> +             * It is easier to handle RDR_full and RDR_overrun status here
> +             * since the RDR register's shift_byte_in method is called
> +             * multiple times in a row. Controlling RDR status is done here
> +             * instead of in the RDR scoped methods for that reason.
> +             */
> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
> +                /*
> +                 * Data was shifted into the RDR before having been read
> +                 * causing previous data to have been overrun.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_OVERRUN, s->status, 1);
> +            } else {
> +                /*
> +                 * Set status to indicate that the received data register is
> +                 * full. This flag is only cleared once the RDR is unloaded.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 1);
> +            }
> +        }
> +    } /* end of else */
> +} /* end of spi_response() */
> +
> +static void transfer(PnvSpi *s, PnvXferBuffer *payload)
> +{
> +    uint32_t tx;
> +    uint32_t rx;
> +    PnvXferBuffer *rsp_payload = NULL;
> +
> +    rsp_payload = pnv_spi_xfer_buffer_new();
> +    for (int offset = 0; offset < payload->len; offset += s->transfer_len) {
> +        tx = 0;
> +        for (int i = 0; i < s->transfer_len; i++) {
> +            if ((offset + i) >= payload->len) {
> +                tx <<= 8;
> +            } else {
> +                tx = (tx << 8) | payload->data[offset + i];
> +            }
> +        }
> +        rx = ssi_transfer(s->ssi_bus, tx);
> +        for (int i = 0; i < s->transfer_len; i++) {
> +            if ((offset + i) >= payload->len) {
> +                break;
> +            }
> +            *(pnv_spi_xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) =
> +                    (rx >> (8 * (s->transfer_len - 1) - i * 8)) & 0xFF;
> +        }
> +    }
> +    if (rsp_payload != NULL) {
> +        spi_response(s, s->N1_bits, rsp_payload);
> +    }
> +}
> +
> +static inline uint8_t get_seq_index(PnvSpi *s)
> +{
> +    return GETFIELD(SPI_STS_SEQ_INDEX, s->status);
> +}
> +
> +static inline void next_sequencer_fsm(PnvSpi *s)
> +{
> +    uint8_t seq_index = get_seq_index(s);
> +    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, (seq_index + 1));
> +    s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_INDEX_INCREMENT);
> +}
> +
> +/*
> + * Calculate the N1 counters based on passed in opcode and
> + * internal register values.
> + * The method assumes that the opcode is a Shift_N1 opcode
> + * and doesn't test it.
> + * The counters returned are:
> + * N1 bits: Number of bits in the payload data that are significant
> + * to the responder.
> + * N1_bytes: Total count of payload bytes for the N1 (portion of the) frame.
> + * N1_tx: Total number of bytes taken from TDR for N1
> + * N1_rx: Total number of bytes taken from the payload for N1
> + */
> +static void calculate_N1(PnvSpi *s, uint8_t opcode)
> +{
> +    /*
> +     * Shift_N1 opcode form: 0x3M
> +     * Implicit mode:
> +     * If M != 0 the shift count is M bytes and M is the number of tx bytes.
> +     * Forced Implicit mode:
> +     * M is the shift count but tx and rx is determined by the count control
> +     * register fields.  Note that we only check for forced Implicit mode when
> +     * M != 0 since the mode doesn't make sense when M = 0.
> +     * Explicit mode:
> +     * If M == 0 then shift count is number of bits defined in the
> +     * Counter Configuration Register's shift_count_N1 field.
> +     */
> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
> +        /* Explicit mode */
> +        s->N1_bits = GETFIELD(SPI_CTR_CFG_N1, s->regs[SPI_CTR_CFG_REG]);
> +        s->N1_bytes = ceil(s->N1_bits / 8);
> +        s->N1_tx = 0;
> +        s->N1_rx = 0;
> +        /* If tx count control for N1 is set, load the tx value */
> +        if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N1_tx = s->N1_bytes;
> +        }
> +        /* If rx count control for N1 is set, load the rx value */
> +        if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N1_rx = s->N1_bytes;
> +        }
> +    } else {
> +        /* Implicit mode/Forced Implicit mode, use M field from opcode */
> +        s->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
> +        s->N1_bits = s->N1_bytes * 8;
> +        /*
> +         * Assume that we are going to transmit the count
> +         * (pure Implicit only)
> +         */
> +        s->N1_tx = s->N1_bytes;
> +        s->N1_rx = 0;
> +        /* Let Forced Implicit mode have an effect on the counts */
> +        if (GETFIELD(PPC_BIT(49), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            /*
> +             * If Forced Implicit mode and count control doesn't
> +             * indicate transmit then reset the tx count to 0
> +             */
> +            if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 0) {
> +                s->N1_tx = 0;
> +            }
> +            /* If rx count control for N1 is set, load the rx value */
> +            if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +                s->N1_rx = s->N1_bytes;
> +            }
> +        }
> +    }
> +    /*
> +     * Enforce an upper limit on the size of N1 that is equal to the known size
> +     * of the shift register, 64 bits or 72 bits if ECC is enabled.
> +     * If the size exceeds 72 bits it is a user error so log an error,
> +     * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM
> +     * error bit.
> +     */
> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
> +                                   s->regs[SPI_CLK_CFG_REG]);
> +    if (ecc_control == 0 || ecc_control == 2) {
> +        if (s->N1_bytes > (PNV_SPI_REG_SIZE + 1)) {
> +            qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size when "
> +                          "ECC enabled, bytes = 0x%x, bits = 0x%x\n",
> +                          s->N1_bytes, s->N1_bits);
> +            s->N1_bytes = PNV_SPI_REG_SIZE + 1;
> +            s->N1_bits = s->N1_bytes * 8;
> +        }
> +    } else if (s->N1_bytes > PNV_SPI_REG_SIZE) {
> +        qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, "
> +                      "bytes = 0x%x, bits = 0x%x\n",
> +                      s->N1_bytes, s->N1_bits);
> +        s->N1_bytes = PNV_SPI_REG_SIZE;
> +        s->N1_bits = s->N1_bytes * 8;
> +    }
> +} /* end of calculate_N1 */
> +
> +/*
> + * Shift_N1 operation handler method
> + */
> +static bool operation_shiftn1(PnvSpi *s, uint8_t opcode,
> +                       PnvXferBuffer **payload, bool send_n1_alone)
> +{
> +    uint8_t n1_count;
> +    bool stop = false;
> +
> +    /*
> +     * If there isn't a current payload left over from a stopped sequence
> +     * create a new one.
> +     */
> +    if (*payload == NULL) {
> +        *payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Use a combination of N1 counters to build the N1 portion of the
> +     * transmit payload.
> +     * We only care about transmit at this time since the request payload
> +     * only represents data going out on the controller output line.
> +     * Leave mode specific considerations in the calculate function since
> +     * all we really care about are counters that tell use exactly how
> +     * many bytes are in the payload and how many of those bytes to
> +     * include from the TDR into the payload.
> +     */
> +    calculate_N1(s, opcode);
> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
> +    /*
> +     * Zero out the N2 counters here in case there is no N2 operation following
> +     * the N1 operation in the sequencer.  This keeps leftover N2 information
> +     * from interfering with spi_response logic.
> +     */
> +    s->N2_bits = 0;
> +    s->N2_bytes = 0;
> +    s->N2_tx = 0;
> +    s->N2_rx = 0;
> +    /*
> +     * N1_bytes is the overall size of the N1 portion of the frame regardless of
> +     * whether N1 is used for tx, rx or both.  Loop over the size to build a
> +     * payload that is N1_bytes long.
> +     * N1_tx is the count of bytes to take from the TDR and "shift" into the
> +     * frame which means append those bytes to the payload for the N1 portion
> +     * of the frame.
> +     * If N1_tx is 0 or if the count exceeds the size of the TDR append 0xFF to
> +     * the frame until the overall N1 count is reached.
> +     */
> +    n1_count = 0;
> +    while (n1_count < s->N1_bytes) {
> +        /*
> +         * Assuming that if N1_tx is not equal to 0 then it is the same as
> +         * N1_bytes.
> +         */
> +        if ((s->N1_tx != 0) && (n1_count < PNV_SPI_REG_SIZE)) {
> +
> +            if (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1) {
> +                /*
> +                 * Note that we are only appending to the payload IF the TDR
> +                 * is full otherwise we don't touch the payload because we are
> +                 * going to NOT send the payload and instead tell the sequencer
> +                 * that called us to stop and wait for a TDR write so we have
> +                 * data to load into the payload.
> +                 */
> +                uint8_t n1_byte = 0x00;
> +                n1_byte = get_from_offset(s, n1_count);
> +                trace_pnv_spi_tx_append("n1_byte", n1_byte, n1_count);
> +                *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) =
> +                        n1_byte;
> +            } else {
> +                /*
> +                 * We hit a shift_n1 opcode TX but the TDR is empty, tell the
> +                 * sequencer to stop and break this loop.
> +                 */
> +                trace_pnv_spi_sequencer_stop_requested("Shift N1"
> +                                "set for transmit but TDR is empty");
> +                stop = true;
> +                break;
> +            }
> +        } else {
> +            /*
> +             * Cases here:
> +             * - we are receiving during the N1 frame segment and the RDR
> +             *   is full so we need to stop until the RDR is read
> +             * - we are transmitting and we don't care about RDR status
> +             *   since we won't be loading RDR during the frame segment.
> +             * - we are receiving and the RDR is empty so we allow the operation
> +             *   to proceed.
> +             */
> +            if ((s->N1_rx != 0) && (GETFIELD(SPI_STS_RDR_FULL,
> +                                           s->status) == 1)) {
> +                trace_pnv_spi_sequencer_stop_requested("shift N1"
> +                                "set for receive but RDR is full");
> +                stop = true;
> +                break;
> +            } else {
> +                trace_pnv_spi_tx_append_FF("n1_byte");
> +                *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
> +                        = 0xff;
> +            }
> +        }
> +        n1_count++;
> +    } /* end of while */
> +    /*
> +     * If we are not stopping due to an empty TDR and we are doing an N1 TX
> +     * and the TDR is full we need to clear the TDR_full status.
> +     * Do this here instead of up in the loop above so we don't log the message
> +     * in every loop iteration.
> +     * Ignore the send_n1_alone flag, all that does is defer the TX until the N2
> +     * operation, which was found immediately after the current opcode.  The TDR
> +     * was unloaded and will be shifted so we have to clear the TDR_full status.
> +     */
> +    if (!stop && (s->N1_tx != 0) &&
> +        (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
> +        s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
> +    }
> +    /*
> +     * There are other reasons why the shifter would stop, such as a TDR empty
> +     * or RDR full condition with N1 set to receive.  If we haven't stopped due
> +     * to either one of those conditions then check if the send_n1_alone flag is
> +     * equal to False, indicating the next opcode is an N2 operation, AND if
> +     * the N2 counter reload switch (bit 0 of the N2 count control field) is
> +     * set.  This condition requires a pacing write to "kick" off the N2
> +     * shift which includes the N1 shift as well when send_n1_alone is False.
> +     */
> +    if (!stop && !send_n1_alone &&
> +       (GETFIELD(PPC_BIT(52), s->regs[SPI_CTR_CFG_REG]) == 1)) {
> +        trace_pnv_spi_sequencer_stop_requested("N2 counter reload "
> +                        "active, stop N1 shift, TDR_underrun set to 1");
> +        stop = true;
> +        s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 1);
> +    }
> +    /*
> +     * If send_n1_alone is set AND we have a full TDR then this is the first and
> +     * last payload to send and we don't have an N2 frame segment to add to the
> +     * payload.
> +     */
> +    if (send_n1_alone && !stop) {
> +        /* We have a TX and a full TDR or an RX and an empty RDR */
> +        trace_pnv_spi_tx_request("Shifting N1 frame", (*payload)->len);
> +        transfer(s, *payload);
> +        /* The N1 frame shift is complete so reset the N1 counters */
> +        s->N2_bits = 0;
> +        s->N2_bytes = 0;
> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        pnv_spi_xfer_buffer_free(*payload);
> +        *payload = NULL;
> +    }
> +    return stop;
> +} /* end of operation_shiftn1() */
> +
> +/*
> + * Calculate the N2 counters based on passed in opcode and
> + * internal register values.
> + * The method assumes that the opcode is a Shift_N2 opcode
> + * and doesn't test it.
> + * The counters returned are:
> + * N2 bits: Number of bits in the payload data that are significant
> + * to the responder.
> + * N2_bytes: Total count of payload bytes for the N2 frame.
> + * N2_tx: Total number of bytes taken from TDR for N2
> + * N2_rx: Total number of bytes taken from the payload for N2
> + */
> +static void calculate_N2(PnvSpi *s, uint8_t opcode)
> +{
> +    /*
> +     * Shift_N2 opcode form: 0x4M
> +     * Implicit mode:
> +     * If M!=0 the shift count is M bytes and M is the number of rx bytes.
> +     * Forced Implicit mode:
> +     * M is the shift count but tx and rx is determined by the count control
> +     * register fields.  Note that we only check for Forced Implicit mode when
> +     * M != 0 since the mode doesn't make sense when M = 0.
> +     * Explicit mode:
> +     * If M==0 then shift count is number of bits defined in the
> +     * Counter Configuration Register's shift_count_N1 field.
> +     */
> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
> +        /* Explicit mode */
> +        s->N2_bits = GETFIELD(SPI_CTR_CFG_N2, s->regs[SPI_CTR_CFG_REG]);
> +        s->N2_bytes = ceil(s->N2_bits / 8);
> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        /* If tx count control for N2 is set, load the tx value */
> +        if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N2_tx = s->N2_bytes;
> +        }
> +        /* If rx count control for N2 is set, load the rx value */
> +        if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N2_rx = s->N2_bytes;
> +        }
> +    } else {
> +        /* Implicit mode/Forced Implicit mode, use M field from opcode */
> +        s->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
> +        s->N2_bits = s->N2_bytes * 8;
> +        /* Assume that we are going to receive the count */
> +        s->N2_rx = s->N2_bytes;
> +        s->N2_tx = 0;
> +        /* Let Forced Implicit mode have an effect on the counts */
> +        if (GETFIELD(PPC_BIT(53), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            /*
> +             * If Forced Implicit mode and count control doesn't
> +             * indicate a receive then reset the rx count to 0
> +             */
> +            if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 0) {
> +                s->N2_rx = 0;
> +            }
> +            /* If tx count control for N2 is set, load the tx value */
> +            if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +                s->N2_tx = s->N2_bytes;
> +            }
> +        }
> +    }
> +    /*
> +     * Enforce an upper limit on the size of N1 that is equal to the
> +     * known size of the shift register, 64 bits or 72 bits if ECC
> +     * is enabled.
> +     * If the size exceeds 72 bits it is a user error so log an error,
> +     * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM
> +     * error bit.
> +     */
> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
> +                                   s->regs[SPI_CLK_CFG_REG]);
> +    if (ecc_control == 0 || ecc_control == 2) {
> +        if (s->N2_bytes > (PNV_SPI_REG_SIZE + 1)) {
> +            /* Unsupported N2 shift size when ECC enabled */
> +            s->N2_bytes = PNV_SPI_REG_SIZE + 1;
> +            s->N2_bits = s->N2_bytes * 8;
> +        }
> +    } else if (s->N2_bytes > PNV_SPI_REG_SIZE) {
> +        /* Unsupported N2 shift size */
> +        s->N2_bytes = PNV_SPI_REG_SIZE;
> +        s->N2_bits = s->N2_bytes * 8;
> +    }
> +} /* end of calculate_N2 */
> +
> +/*
> + * Shift_N2 operation handler method
> + */
> +
> +static bool operation_shiftn2(PnvSpi *s, uint8_t opcode,
> +                       PnvXferBuffer **payload)
> +{
> +    uint8_t n2_count;
> +    bool stop = false;
> +
> +    /*
> +     * If there isn't a current payload left over from a stopped sequence
> +     * create a new one.
> +     */
> +    if (*payload == NULL) {
> +        *payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Use a combination of N2 counters to build the N2 portion of the
> +     * transmit payload.
> +     */
> +    calculate_N2(s, opcode);
> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
> +    /*
> +     * The only difference between this code and the code for shift N1 is
> +     * that this code has to account for the possible presence of N1 transmit
> +     * bytes already taken from the TDR.
> +     * If there are bytes to be transmitted for the N2 portion of the frame
> +     * and there are still bytes in TDR that have not been copied into the
> +     * TX data of the payload, this code will handle transmitting those
> +     * remaining bytes.
> +     * If for some reason the transmit count(s) add up to more than the size
> +     * of the TDR we will just append 0xFF to the transmit payload data until
> +     * the payload is N1 + N2 bytes long.
> +     */
> +    n2_count = 0;
> +    while (n2_count < s->N2_bytes) {
> +        /*
> +         * If the RDR is full and we need to RX just bail out, letting the
> +         * code continue will end up building the payload twice in the same
> +         * buffer since RDR full causes a sequence stop and restart.
> +         */
> +        if ((s->N2_rx != 0) &&
> +            (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1)) {
> +            trace_pnv_spi_sequencer_stop_requested("shift N2 set"
> +                            "for receive but RDR is full");
> +            stop = true;
> +            break;
> +        }
> +        if ((s->N2_tx != 0) && ((s->N1_tx + n2_count) <
> +                                PNV_SPI_REG_SIZE)) {
> +            /* Always append data for the N2 segment if it is set for TX */
> +            uint8_t n2_byte = 0x00;
> +            n2_byte = get_from_offset(s, (s->N1_tx + n2_count));
> +            trace_pnv_spi_tx_append("n2_byte", n2_byte, (s->N1_tx + n2_count));
> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
> +                    = n2_byte;
> +        } else {
> +            /*
> +             * Regardless of whether or not N2 is set for TX or RX, we need
> +             * the number of bytes in the payload to match the overall length
> +             * of the operation.
> +             */
> +            trace_pnv_spi_tx_append_FF("n2_byte");
> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
> +                    = 0xff;
> +        }
> +        n2_count++;
> +    } /* end of while */
> +    if (!stop) {
> +        /* We have a TX and a full TDR or an RX and an empty RDR */
> +        trace_pnv_spi_tx_request("Shifting N2 frame", (*payload)->len);
> +        transfer(s, *payload);
> +        /*
> +         * If we are doing an N2 TX and the TDR is full we need to clear the
> +         * TDR_full status. Do this here instead of up in the loop above so we
> +         * don't log the message in every loop iteration.
> +         */
> +        if ((s->N2_tx != 0) &&
> +            (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
> +            s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
> +        }
> +        /*
> +         * The N2 frame shift is complete so reset the N2 counters.
> +         * Reset the N1 counters also in case the frame was a combination of
> +         * N1 and N2 segments.
> +         */
> +        s->N2_bits = 0;
> +        s->N2_bytes = 0;
> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        s->N1_bits = 0;
> +        s->N1_bytes = 0;
> +        s->N1_tx = 0;
> +        s->N1_rx = 0;
> +        pnv_spi_xfer_buffer_free(*payload);
> +        *payload = NULL;
> +    }
> +    return stop;
> +} /*  end of operation_shiftn2()*/
> +
> +static void operation_sequencer(PnvSpi *s)
> +{
> +    /*
> +     * Loop through each sequencer operation ID and perform the requested
> +     *  operations.
> +     * Flag for indicating if we should send the N1 frame or wait to combine
> +     * it with a preceding N2 frame.
> +     */
> +    bool send_n1_alone = true;
> +    bool stop = false; /* Flag to stop the sequencer */
> +    uint8_t opcode = 0;
> +    uint8_t masked_opcode = 0;
> +
> +    /*
> +     * PnvXferBuffer for containing the payload of the SPI frame.
> +     * This is a static because there are cases where a sequence has to stop
> +     * and wait for the target application to unload the RDR.  If this occurs
> +     * during a sequence where N1 is not sent alone and instead combined with
> +     * N2 since the N1 tx length + the N2 tx length is less than the size of
> +     * the TDR.
> +     */
> +    static PnvXferBuffer *payload;
> +
> +    if (payload == NULL) {
> +        payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Clear the sequencer FSM error bit - general_SPI_status[3]
> +     * before starting a sequence.
> +     */
> +    s->status = SETFIELD(PPC_BIT(35), s->status, 0);
> +    /*
> +     * If the FSM is idle set the sequencer index to 0
> +     * (new/restarted sequence)
> +     */
> +    if (GETFIELD(SPI_STS_SEQ_FSM, s->status) == SEQ_STATE_IDLE) {
> +        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
> +    }
> +    /*
> +     * There are only 8 possible operation IDs to iterate through though
> +     * some operations may cause more than one frame to be sequenced.
> +     */
> +    while (get_seq_index(s) < 8) {
> +        opcode = s->seq_op[get_seq_index(s)];
> +        /* Set sequencer state to decode */
> +        s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_DECODE);
> +        /*
> +         * Only the upper nibble of the operation ID is needed to know what
> +         * kind of operation is requested.
> +         */
> +        masked_opcode = opcode & 0xF0;
> +        switch (masked_opcode) {
> +        /*
> +         * Increment the operation index in each case instead of just
> +         * once at the end in case an operation like the branch
> +         * operation needs to change the index.
> +         */
> +        case SEQ_OP_STOP:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            /* A stop operation in any position stops the sequencer */
> +            trace_pnv_spi_sequencer_op("STOP", get_seq_index(s));
> +
> +            stop = true;
> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
> +            s->loop_counter_1 = 0;
> +            s->loop_counter_2 = 0;
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_IDLE);
> +            break;
> +
> +        case SEQ_OP_SELECT_SLAVE:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SELECT_SLAVE", get_seq_index(s));
> +            /*
> +             * This device currently only supports a single responder
> +             * connection at position 0.  De-selecting a responder is fine
> +             * and expected at the end of a sequence but selecting any
> +             * responder other than 0 should cause an error.
> +             */
> +            s->responder_select = opcode & 0x0F;
> +            if (s->responder_select == 0) {
> +                trace_pnv_spi_shifter_done();
> +                qemu_set_irq(s->cs_line[0], 1);
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                (get_seq_index(s) + 1));
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_DONE);
> +            } else if (s->responder_select != 1) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Slave selection other than 1 "
> +                              "not supported, select = 0x%x\n",
> +                               s->responder_select);
> +                trace_pnv_spi_sequencer_stop_requested("invalid "
> +                                "responder select");
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
> +                stop = true;
> +            } else {
> +                /*
> +                 * Only allow an FSM_START state when a responder is
> +                 * selected
> +                 */
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_START);
> +                trace_pnv_spi_shifter_stating();
> +                qemu_set_irq(s->cs_line[0], 0);
> +                /*
> +                 * A Shift_N2 operation is only valid after a Shift_N1
> +                 * according to the spec. The spec doesn't say if that means
> +                 * immediately after or just after at any point. We will track
> +                 * the occurrence of a Shift_N1 to enforce this requirement in
> +                 * the most generic way possible by assuming that the rule
> +                 * applies once a valid responder select has occurred.
> +                 */
> +                s->shift_n1_done = false;
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        case SEQ_OP_SHIFT_N1:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SHIFT_N1", get_seq_index(s));
> +            /*
> +             * Only allow a shift_n1 when the state is not IDLE or DONE.
> +             * In either of those two cases the sequencer is not in a proper
> +             * state to perform shift operations because the sequencer has:
> +             * - processed a responder deselect (DONE)
> +             * - processed a stop opcode (IDLE)
> +             * - encountered an error (IDLE)
> +             */
> +            if ((GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_IDLE) ||
> +                (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_DONE)) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed in "
> +                              "shifter state = 0x%llx", GETFIELD(
> +                        SPI_STS_SHIFTER_FSM, s->status));
> +                /*
> +                 * Set sequencer FSM error bit 3 (general_SPI_status[3])
> +                 * in status reg.
> +                 */
> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
> +                trace_pnv_spi_sequencer_stop_requested("invalid shifter state");
> +                stop = true;
> +            } else {
> +                /*
> +                 * Look for the special case where there is a shift_n1 set for
> +                 * transmit and it is followed by a shift_n2 set for transmit
> +                 * AND the combined transmit length of the two operations is
> +                 * less than or equal to the size of the TDR register. In this
> +                 * case we want to use both this current shift_n1 opcode and the
> +                 * following shift_n2 opcode to assemble the frame for
> +                 * transmission to the responder without requiring a refill of
> +                 * the TDR between the two operations.
> +                 */
> +                if ((s->seq_op[get_seq_index(s) + 1] & 0xF0)
> +                                == SEQ_OP_SHIFT_N2) {
> +                    send_n1_alone = false;
> +                }
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                FSM_SHIFT_N1);
> +                stop = operation_shiftn1(s, opcode, &payload, send_n1_alone);
> +                if (stop) {
> +                    /*
> +                     *  The operation code says to stop, this can occur if:
> +                     * (1) RDR is full and the N1 shift is set for receive
> +                     * (2) TDR was empty at the time of the N1 shift so we need
> +                     * to wait for data.
> +                     * (3) Neither 1 nor 2 are occurring and we aren't sending
> +                     * N1 alone and N2 counter reload is set (bit 0 of the N2
> +                     * counter reload field).  In this case TDR_underrun will
> +                     * will be set and the Payload has been loaded so it is
> +                     * ok to advance the sequencer.
> +                     */
> +                    if (GETFIELD(SPI_STS_TDR_UNDERRUN, s->status)) {
> +                        s->shift_n1_done = true;
> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                                  FSM_SHIFT_N2);
> +                        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                        (get_seq_index(s) + 1));
> +                    } else {
> +                        /*
> +                         * This is case (1) or (2) so the sequencer needs to
> +                         * wait and NOT go to the next sequence yet.
> +                         */
> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                        FSM_WAIT);
> +                    }
> +                } else {
> +                    /* Ok to move on to the next index */
> +                    s->shift_n1_done = true;
> +                    next_sequencer_fsm(s);
> +                }
> +            }
> +            break;
> +
> +        case SEQ_OP_SHIFT_N2:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SHIFT_N2", get_seq_index(s));
> +            if (!s->shift_n1_done) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not allowed if a "
> +                              "Shift_N1 is not done, shifter state = 0x%llx",
> +                              GETFIELD(SPI_STS_SHIFTER_FSM, s->status));
> +                /*
> +                 * In case the sequencer actually stops if an N2 shift is
> +                 * requested before any N1 shift is done. Set sequencer FSM
> +                 * error bit 3 (general_SPI_status[3]) in status reg.
> +                 */
> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
> +                trace_pnv_spi_sequencer_stop_requested("shift_n2 "
> +                                    "w/no shift_n1 done");
> +                stop = true;
> +            } else {
> +                /* Ok to do a Shift_N2 */
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                FSM_SHIFT_N2);
> +                stop = operation_shiftn2(s, opcode, &payload);
> +                /*
> +                 * If the operation code says to stop set the shifter state to
> +                 * wait and stop
> +                 */
> +                if (stop) {
> +                    s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                    FSM_WAIT);
> +                } else {
> +                    /* Ok to move on to the next index */
> +                    next_sequencer_fsm(s);
> +                }
> +            }
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_RDR:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_RDR", get_seq_index(s));
> +            /*
> +             * The memory mapping register RDR match value is compared against
> +             * the 16 rightmost bytes of the RDR (potentially with masking).
> +             * Since this comparison is performed against the contents of the
> +             * RDR then a receive must have previously occurred otherwise
> +             * there is no data to compare and the operation cannot be
> +             * completed and will stop the sequencer until RDR full is set to
> +             * 1.
> +             */
> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
> +                bool rdr_matched = false;
> +                rdr_matched = does_rdr_match(s);
> +                if (rdr_matched) {
> +                    trace_pnv_spi_RDR_match("success");
> +                    /* A match occurred, increment the sequencer index. */
> +                    next_sequencer_fsm(s);
> +                } else {
> +                    trace_pnv_spi_RDR_match("failed");
> +                    /*
> +                     * Branch the sequencer to the index coded into the op
> +                     * code.
> +                     */
> +                    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                    (opcode & 0x7));
> +                }
> +                /*
> +                 * Regardless of where the branch ended up we want the
> +                 * sequencer to continue shifting so we have to clear
> +                 * RDR_full.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
> +            } else {
> +                trace_pnv_spi_sequencer_stop_requested("RDR not"
> +                                "full for 0x6x opcode");
> +                stop = true;
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_WAIT);
> +            }
> +            break;
> +
> +        case SEQ_OP_TRANSFER_TDR:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not supported\n");
> +            next_sequencer_fsm(s);
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_INC_1:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_1", get_seq_index(s));
> +            /*
> +             * The spec says the loop should execute count compare + 1 times.
> +             * However we learned from engineering that we really only loop
> +             * count_compare times, count compare = 0 makes this op code a
> +             * no-op
> +             */
> +            if (s->loop_counter_1 !=
> +                GETFIELD(SPI_CTR_CFG_CMP1, s->regs[SPI_CTR_CFG_REG])) {
> +                /*
> +                 * Next index is the lower nibble of the branch operation ID,
> +                 * mask off all but the first three bits so we don't try to
> +                 * access beyond the sequencer_operation_reg boundary.
> +                 */
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                (opcode & 0x7));
> +                s->loop_counter_1++;
> +            } else {
> +                /* Continue to next index if loop counter is reached */
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_INC_2:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_2", get_seq_index(s));
> +            uint8_t condition2 = GETFIELD(SPI_CTR_CFG_CMP2,
> +                              s->regs[SPI_CTR_CFG_REG]);
> +            /*
> +             * The spec says the loop should execute count compare + 1 times.
> +             * However we learned from engineering that we really only loop
> +             * count_compare times, count compare = 0 makes this op code a
> +             * no-op
> +             */
> +            if (s->loop_counter_2 != condition2) {
> +                /*
> +                 * Next index is the lower nibble of the branch operation ID,
> +                 * mask off all but the first three bits so we don't try to
> +                 * access beyond the sequencer_operation_reg boundary.
> +                 */
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                          (opcode & 0x7));
> +                s->loop_counter_2++;
> +            } else {
> +                /* Continue to next index if loop counter is reached */
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        default:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
> +            /* Ignore unsupported operations. */
> +            next_sequencer_fsm(s);
> +            break;
> +        } /* end of switch */
> +        /*
> +         * If we used all 8 opcodes without seeing a 00 - STOP in the sequence
> +         * we need to go ahead and end things as if there was a STOP at the
> +         * end.
> +         */
> +        if (get_seq_index(s) == 8) {
> +            /* All 8 opcodes completed, sequencer idling */
> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
> +            s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
> +            s->loop_counter_1 = 0;
> +            s->loop_counter_2 = 0;
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_IDLE);
> +            break;
> +        }
> +        /* Break the loop if a stop was requested */
> +        if (stop) {
> +            break;
> +        }
> +    } /* end of while */
> +    return;
> +} /* end of operation_sequencer() */
> +
> +/*
> + * The SPIC engine and its internal sequencer can be interrupted and reset by
> + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive
> + * Miscellaneous Register of sbe_register_bo device.
> + * Reset immediately aborts any SPI transaction in progress and returns the
> + * sequencer and state machines to idle state.
> + * The configuration register values are not changed. The status register is
> + * not reset. The engine registers are not reset.
> + * The SPIC engine reset does not have any affect on the attached devices.
> + * Reset handling of any attached devices is beyond the scope of the engine.
> + */
> +static void do_reset(DeviceState *dev)
> +{
> +    PnvSpi *s = PNV_SPI(dev);
> +
> +    trace_pnv_spi_reset();
> +
> +    /* Reset all N1 and N2 counters, and other constants */
> +    s->N2_bits = 0;
> +    s->N2_bytes = 0;
> +    s->N2_tx = 0;
> +    s->N2_rx = 0;
> +    s->N1_bits = 0;
> +    s->N1_bytes = 0;
> +    s->N1_tx = 0;
> +    s->N1_rx = 0;
> +    s->loop_counter_1 = 0;
> +    s->loop_counter_2 = 0;
> +    /* Disconnected from responder */
> +    qemu_set_irq(s->cs_line[0], 1);
> +}
> +
>   static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr, unsigned size)
>   {
>       PnvSpi *s = PNV_SPI(opaque);
> @@ -36,6 +1067,10 @@ static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr, unsigned size)
>           val = s->regs[reg];
>           trace_pnv_spi_read_RDR(val);
>           s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
> +        if (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_WAIT) {
> +            trace_pnv_spi_start_sequencer();
> +            operation_sequencer(s);
> +        }
>           break;
>       case SPI_SEQ_OP_REG:
>           val = 0;
> @@ -97,6 +1132,8 @@ static void pnv_spi_xscom_write(void *opaque, hwaddr addr,
>           trace_pnv_spi_write_TDR(val);
>           s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 1);
>           s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 0);
> +        trace_pnv_spi_start_sequencer();
> +        operation_sequencer(s);
>           break;
>       case SPI_SEQ_OP_REG:
>           for (int i = 0; i < PNV_SPI_REG_SIZE; i++) {
> @@ -129,6 +1166,7 @@ static const MemoryRegionOps pnv_spi_xscom_ops = {
>   
>   static Property pnv_spi_properties[] = {
>       DEFINE_PROP_UINT32("spic_num", PnvSpi, spic_num, 0),
> +    DEFINE_PROP_UINT8("transfer_len", PnvSpi, transfer_len, 4),
>       DEFINE_PROP_END_OF_LIST(),
>   };
>   
> @@ -180,6 +1218,7 @@ static void pnv_spi_class_init(ObjectClass *klass, void *data)
>   
>       dc->desc = "PowerNV SPI";
>       dc->realize = pnv_spi_realize;
> +    dc->reset = do_reset;
>       device_class_set_props(dc, pnv_spi_properties);
>   }
>   
> diff --git a/hw/ssi/trace-events b/hw/ssi/trace-events
> index 4388024a05..7fa27ebade 100644
> --- a/hw/ssi/trace-events
> +++ b/hw/ssi/trace-events
> @@ -38,3 +38,18 @@ pnv_spi_read(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val 0x%" PRIx64
>   pnv_spi_write(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val 0x%" PRIx64
>   pnv_spi_read_RDR(uint64_t val) "data extracted = 0x%" PRIx64
>   pnv_spi_write_TDR(uint64_t val) "being written, data written = 0x%" PRIx64
> +pnv_spi_start_sequencer(void) ""
> +pnv_spi_reset(void) "spic engine sequencer configuration and spi communication"
> +pnv_spi_sequencer_op(const char* op, uint8_t index) "%s at index = 0x%x"
> +pnv_spi_shifter_stating(void) "pull CS line low"
> +pnv_spi_shifter_done(void) "pull the CS line high"
> +pnv_spi_log_Ncounts(uint8_t N1_bits, uint8_t N1_bytes, uint8_t N1_tx, uint8_t N1_rx, uint8_t N2_bits, uint8_t N2_bytes, uint8_t N2_tx, uint8_t N2_rx) "N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx = %d, N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d"
> +pnv_spi_tx_append(const char* frame, uint8_t byte, uint8_t tdr_index) "%s = 0x%2.2x to payload from TDR at index %d"
> +pnv_spi_tx_append_FF(const char* frame) "%s to Payload"
> +pnv_spi_tx_request(const char* frame, uint32_t payload_len) "%s, payload len = %d"
> +pnv_spi_rx_received(uint32_t payload_len) "payload len = %d"
> +pnv_spi_rx_read_N1frame(void) ""
> +pnv_spi_rx_read_N2frame(void) ""
> +pnv_spi_shift_rx(uint8_t byte, uint32_t index) "byte = 0x%2.2x into RDR from payload index %d"
> +pnv_spi_sequencer_stop_requested(const char* reason) "due to %s"
> +pnv_spi_RDR_match(const char* result) "%s"
Miles Glenn June 19, 2024, 10:14 p.m. UTC | #2
Hi Chalapathi,

I can't say I have a great understanding of this IBM SPI controller,
but I did find some places for improvement, mostly dealing with the use
of "magic numbers" throughout the code.  Please see comments below.

Thanks,

Glenn

On Mon, 2024-06-17 at 11:54 -0500, Chalapathi V wrote:
> In this commit SPI shift engine and sequencer logic is implemented.
> Shift engine performs serialization and de-serialization according to
> the
> control by the sequencer and according to the setup defined in the
> configuration registers. Sequencer implements the main control logic
> and
> FSM to handle data transmit and data receive control of the shift
> engine.
> 
> Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
> ---
>  include/hw/ssi/pnv_spi.h |   27 +
>  hw/ssi/pnv_spi.c         | 1039
> ++++++++++++++++++++++++++++++++++++++
>  hw/ssi/trace-events      |   15 +
>  3 files changed, 1081 insertions(+)
> 
> diff --git a/include/hw/ssi/pnv_spi.h b/include/hw/ssi/pnv_spi.h
> index 71c53d4a17..21fbfcb69c 100644
> --- a/include/hw/ssi/pnv_spi.h
> +++ b/include/hw/ssi/pnv_spi.h
> @@ -8,6 +8,14 @@
>   * This model Supports a connection to a single SPI responder.
>   * Introduced for P10 to provide access to SPI seeproms, TPM, flash
> device
>   * and an ADC controller.
> + *
> + * All SPI function control is mapped into the SPI register space to
> enable
> + * full control by firmware.
> + *
> + * SPI Controller has sequencer and shift engine. The SPI shift
> engine
> + * performs serialization and de-serialization according to the
> control by
> + * the sequencer and according to the setup defined in the
> configuration
> + * registers and the SPI sequencer implements the main control
> logic.
>   */
>  #include "hw/ssi/ssi.h"
>  #include "hw/sysbus.h"
> @@ -50,6 +58,25 @@ typedef struct PnvSpi {
>      MemoryRegion    xscom_spic_regs;
>      /* SPI object number */
>      uint32_t        spic_num;
> +    uint8_t         transfer_len;
> +    uint8_t         responder_select;
> +    /* To verify if shift_n1 happens prior to shift_n2 */
> +    bool            shift_n1_done;
> +    /* Loop counter for branch operation opcode Ex/Fx */
> +    uint8_t         loop_counter_1;
> +    uint8_t         loop_counter_2;
> +    /* N1/N2_bits specifies the size of the N1/N2 segment of a frame
> in bits.*/
> +    uint8_t         N1_bits;
> +    uint8_t         N2_bits;
> +    /* Number of bytes in a payload for the N1/N2 frame segment.*/
> +    uint8_t         N1_bytes;
> +    uint8_t         N2_bytes;
> +    /* Number of N1/N2 bytes marked for transmit */
> +    uint8_t         N1_tx;
> +    uint8_t         N2_tx;
> +    /* Number of N1/N2 bytes marked for receive */
> +    uint8_t         N1_rx;
> +    uint8_t         N2_rx;
>  
>      /* SPI registers */
>      uint64_t        regs[PNV_SPI_REGS];
> diff --git a/hw/ssi/pnv_spi.c b/hw/ssi/pnv_spi.c
> index da9e3925dd..b8f4370525 100644
> --- a/hw/ssi/pnv_spi.c
> +++ b/hw/ssi/pnv_spi.c
> @@ -14,9 +14,1040 @@
>  #include "hw/ssi/pnv_spi_regs.h"
>  #include "hw/ssi/ssi.h"
>  #include <libfdt.h>
> +#include <math.h>

I think the only reason you are including math.h is because you're
using the `ceil` function below.  And, since you are only using it to
operate on integers, it is not really necessary.  See comment below on
how to do the same thing with integer math.

>  #include "hw/irq.h"
>  #include "trace.h"
>  
> +/* PnvXferBuffer */
> +typedef struct PnvXferBuffer {
> +
> +    uint32_t    len;
> +    uint8_t    *data;
> +
> +} PnvXferBuffer;
> +
> +/* pnv_spi_xfer_buffer_methods */
> +static PnvXferBuffer *pnv_spi_xfer_buffer_new(void)
> +{
> +    PnvXferBuffer *payload = g_malloc0(sizeof(*payload));
> +
> +    return payload;
> +}
> +
> +static void pnv_spi_xfer_buffer_free(PnvXferBuffer *payload)
> +{
> +    free(payload->data);
> +    free(payload);
> +}
> +
> +static uint8_t *pnv_spi_xfer_buffer_write_ptr(PnvXferBuffer
> *payload,
> +                uint32_t offset, uint32_t length)
> +{
> +    if (payload->len < (offset + length)) {
> +        payload->len = offset + length;
> +        payload->data = g_realloc(payload->data, payload->len);
> +    }
> +    return &payload->data[offset];
> +}
> +
> +static bool does_rdr_match(PnvSpi *s)
> +{
> +    /*
> +     * According to spec, the mask bits that are 0 are compared and
> the
> +     * bits that are 1 are ignored.
> +     */
> +    uint16_t rdr_match_mask = GETFIELD(SPI_MM_RDR_MATCH_MASK,
> +                                        s->regs[SPI_MM_REG]);
> +    uint16_t rdr_match_val = GETFIELD(SPI_MM_RDR_MATCH_VAL,
> +                                        s->regs[SPI_MM_REG]);
> +
> +    if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) &
> +            GETFIELD(PPC_BITMASK(48, 63), s-
> >regs[SPI_RCV_DATA_REG]))) {
> +        return true;
> +    }
> +    return false;
> +}
> +
> +static uint8_t get_from_offset(PnvSpi *s, uint8_t offset)
> +{
> +    uint8_t byte;
> +
> +    /*
> +     * Offset is an index between 0 and PNV_SPI_REG_SIZE - 1
> +     * Check the offset before using it.
> +     */
> +    if (offset < PNV_SPI_REG_SIZE) {
> +        byte = (s->regs[SPI_XMIT_DATA_REG] >> (56 - offset * 8)) &
> 0xFF;
> +    } else {
> +        /*
> +         * Log an error and return a 0xFF since we have to assign
> something
> +         * to byte before returning.
> +         */
> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to
> get byte "
> +                      "from TDR\n", offset);
> +        byte = 0xff;
> +    }
> +    return byte;
> +}
> +
> +static uint8_t read_from_frame(PnvSpi *s, uint8_t *read_buf, uint8_t
> nr_bytes,
> +                uint8_t ecc_count, uint8_t shift_in_count)
> +{
> +    uint8_t byte;
> +    int count = 0;
> +
> +    while (count < nr_bytes) {
> +        shift_in_count++;
> +        if ((ecc_count != 0) &&
> +            (shift_in_count == (PNV_SPI_REG_SIZE + ecc_count))) {
> +            shift_in_count = 0;
> +        } else {
> +            byte = read_buf[count];
> +            trace_pnv_spi_shift_rx(byte, count);
> +            s->regs[SPI_RCV_DATA_REG] = (s->regs[SPI_RCV_DATA_REG]
> << 8) | byte;
> +        }
> +        count++;
> +    } /* end of while */
> +    return shift_in_count;
> +}
> +
> +static void spi_response(PnvSpi *s, int bits, PnvXferBuffer
> *rsp_payload)
> +{
> +    uint8_t ecc_count;
> +    uint8_t shift_in_count;
> +
> +    /*
> +     * Processing here must handle:
> +     * - Which bytes in the payload we should move to the RDR
> +     * - Explicit mode counter configuration settings
> +     * - RDR full and RDR overrun status
> +     */
> +
> +    /*
> +     * First check that the response payload is the exact same
> +     * number of bytes as the request payload was
> +     */
> +    if (rsp_payload->len != (s->N1_bytes + s->N2_bytes)) {
> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload
> size in "
> +                       "bytes, expected %d, got %d\n",
> +                       (s->N1_bytes + s->N2_bytes), rsp_payload-
> >len);
> +    } else {
> +        uint8_t ecc_control;
> +        trace_pnv_spi_rx_received(rsp_payload->len);
> +        trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                        s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, 
> s->N2_rx);
> +        /*
> +         * Adding an ECC count let's us know when we have found a
> payload byte
> +         * that was shifted in but cannot be loaded into RDR.  Bits
> 29-30 of
> +         * clock_config_reset_control register equal to either 0b00
> or 0b10
> +         * indicate that we are taking in data with ECC and either
> applying
> +         * the ECC or discarding it.
> +         */
> +        ecc_count = 0;

I think you're not using the SPI_CLK_CFG_ECC_CTRL mask here because it
also includes bit 28 and you only need bits 29 and 30.  It would be
better if you split the SPI_CLK_CFG_ECC_CTRL mask into two masks like
this:

#define SPI_CLK_CFG_ECC_EN    PPC_BIT(28)
#define SPI_CLK_CFG_ECC_CTRL  PPC_BITMASK(29, 30)

Then, use SPI_CLK_CFG_ECC_CTRL below.

> +        ecc_control = GETFIELD(PPC_BITMASK(29, 30), s-
> >regs[SPI_CLK_CFG_REG]);
> +        if (ecc_control == 0 || ecc_control == 2) {
> +            ecc_count = 1;
> +        }
> +        /*
> +         * Use the N1_rx and N2_rx counts to control shifting data
> from the
> +         * payload into the RDR.  Keep an overall count of the
> number of bytes
> +         * shifted into RDR so we can discard every 9th byte when
> ECC is
> +         * enabled.
> +         */
> +        shift_in_count = 0;
> +        /* Handle the N1 portion of the frame first */
> +        if (s->N1_rx != 0) {
> +            trace_pnv_spi_rx_read_N1frame();
> +            shift_in_count = read_from_frame(s, &rsp_payload-
> >data[0],
> +                            s->N1_bytes, ecc_count, shift_in_count);
> +        }
> +        /* Handle the N2 portion of the frame */
> +        if (s->N2_rx != 0) {
> +            trace_pnv_spi_rx_read_N2frame();
> +            shift_in_count = read_from_frame(s,
> +                            &rsp_payload->data[s->N1_bytes], s-
> >N2_bytes,
> +                            ecc_count, shift_in_count);
> +        }
> +        if ((s->N1_rx + s->N2_rx) > 0) {
> +            /*
> +             * Data was received so handle RDR status.
> +             * It is easier to handle RDR_full and RDR_overrun
> status here
> +             * since the RDR register's shift_byte_in method is
> called
> +             * multiple times in a row. Controlling RDR status is
> done here
> +             * instead of in the RDR scoped methods for that reason.
> +             */
> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
> +                /*
> +                 * Data was shifted into the RDR before having been
> read
> +                 * causing previous data to have been overrun.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_OVERRUN, s->status, 
> 1);
> +            } else {
> +                /*
> +                 * Set status to indicate that the received data
> register is
> +                 * full. This flag is only cleared once the RDR is
> unloaded.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status,
> 1);
> +            }
> +        }
> +    } /* end of else */
> +} /* end of spi_response() */
> +
> +static void transfer(PnvSpi *s, PnvXferBuffer *payload)
> +{
> +    uint32_t tx;
> +    uint32_t rx;
> +    PnvXferBuffer *rsp_payload = NULL;
> +
> +    rsp_payload = pnv_spi_xfer_buffer_new();
> +    for (int offset = 0; offset < payload->len; offset += s-
> >transfer_len) {
> +        tx = 0;
> +        for (int i = 0; i < s->transfer_len; i++) {
> +            if ((offset + i) >= payload->len) {
> +                tx <<= 8;
> +            } else {
> +                tx = (tx << 8) | payload->data[offset + i];
> +            }
> +        }
> +        rx = ssi_transfer(s->ssi_bus, tx);
> +        for (int i = 0; i < s->transfer_len; i++) {
> +            if ((offset + i) >= payload->len) {
> +                break;
> +            }
> +            *(pnv_spi_xfer_buffer_write_ptr(rsp_payload,
> rsp_payload->len, 1)) =
> +                    (rx >> (8 * (s->transfer_len - 1) - i * 8)) &
> 0xFF;
> +        }
> +    }
> +    if (rsp_payload != NULL) {
> +        spi_response(s, s->N1_bits, rsp_payload);
> +    }
> +}
> +
> +static inline uint8_t get_seq_index(PnvSpi *s)
> +{
> +    return GETFIELD(SPI_STS_SEQ_INDEX, s->status);
> +}
> +
> +static inline void next_sequencer_fsm(PnvSpi *s)
> +{
> +    uint8_t seq_index = get_seq_index(s);
> +    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, (seq_index +
> 1));
> +    s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_INDEX_INCREMENT);
> +}
> +
> +/*
> + * Calculate the N1 counters based on passed in opcode and
> + * internal register values.
> + * The method assumes that the opcode is a Shift_N1 opcode
> + * and doesn't test it.
> + * The counters returned are:
> + * N1 bits: Number of bits in the payload data that are significant
> + * to the responder.
> + * N1_bytes: Total count of payload bytes for the N1 (portion of
> the) frame.
> + * N1_tx: Total number of bytes taken from TDR for N1
> + * N1_rx: Total number of bytes taken from the payload for N1
> + */
> +static void calculate_N1(PnvSpi *s, uint8_t opcode)
> +{
> +    /*
> +     * Shift_N1 opcode form: 0x3M
> +     * Implicit mode:
> +     * If M != 0 the shift count is M bytes and M is the number of
> tx bytes.
> +     * Forced Implicit mode:
> +     * M is the shift count but tx and rx is determined by the count
> control
> +     * register fields.  Note that we only check for forced Implicit
> mode when
> +     * M != 0 since the mode doesn't make sense when M = 0.
> +     * Explicit mode:
> +     * If M == 0 then shift count is number of bits defined in the
> +     * Counter Configuration Register's shift_count_N1 field.
> +     */

Please write a macro to extract the opcode variable out of the opcode
and use it here.  You could call it PNV_SPI_OPCODE_VAR or something
like that.

> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
> +        /* Explicit mode */
> +        s->N1_bits = GETFIELD(SPI_CTR_CFG_N1, s-
> >regs[SPI_CTR_CFG_REG]);
> +        s->N1_bytes = ceil(s->N1_bits / 8);

I think your use of the ceil function above is probably not doing what
you think it should.  N1_bits is an integer and when you divide it by
another integer, 8, I believe it results in another integer without the
decimal part.  This integer will then be converted to a double, which
is what ceil takes.  So, as is, I think you're still getting the floor
value.  Regardless, instead of using ceil, which requires pulling in
the math library, I suggest you use the following integer math:

s->N1_bytes = (s->N1_bits + 7) / 8;


> +        s->N1_tx = 0;
> +        s->N1_rx = 0;
> +        /* If tx count control for N1 is set, load the tx value */

Replace PPC_BIT(50) and PPC_BIT(51) with defined names below

> +        if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N1_tx = s->N1_bytes;
> +        }
> +        /* If rx count control for N1 is set, load the rx value */
> +        if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N1_rx = s->N1_bytes;
> +        }
> +    } else {
> +        /* Implicit mode/Forced Implicit mode, use M field from
> opcode */

Replace GETFIELD below with new macro.

> +        s->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
> +        s->N1_bits = s->N1_bytes * 8;
> +        /*
> +         * Assume that we are going to transmit the count
> +         * (pure Implicit only)
> +         */
> +        s->N1_tx = s->N1_bytes;
> +        s->N1_rx = 0;

Replace PPC_BIT(49), PPC_BIT(50), and PPC_BIT(51) with defined names

> +        /* Let Forced Implicit mode have an effect on the counts */
> +        if (GETFIELD(PPC_BIT(49), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            /*
> +             * If Forced Implicit mode and count control doesn't
> +             * indicate transmit then reset the tx count to 0
> +             */
> +            if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) ==
> 0) {
> +                s->N1_tx = 0;
> +            }
> +            /* If rx count control for N1 is set, load the rx value
> */
> +            if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) ==
> 1) {
> +                s->N1_rx = s->N1_bytes;
> +            }
> +        }
> +    }
> +    /*
> +     * Enforce an upper limit on the size of N1 that is equal to the
> known size
> +     * of the shift register, 64 bits or 72 bits if ECC is enabled.
> +     * If the size exceeds 72 bits it is a user error so log an
> error,
> +     * cap the size at a max of 64 bits or 72 bits and set the
> sequencer FSM
> +     * error bit.
> +     */

Use new SPI_CLK_CFG_ECC_CTRL mask below

> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
> +                                   s->regs[SPI_CLK_CFG_REG]);
> +    if (ecc_control == 0 || ecc_control == 2) {
> +        if (s->N1_bytes > (PNV_SPI_REG_SIZE + 1)) {
> +            qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift
> size when "
> +                          "ECC enabled, bytes = 0x%x, bits =
> 0x%x\n",
> +                          s->N1_bytes, s->N1_bits);
> +            s->N1_bytes = PNV_SPI_REG_SIZE + 1;
> +            s->N1_bits = s->N1_bytes * 8;
> +        }
> +    } else if (s->N1_bytes > PNV_SPI_REG_SIZE) {
> +        qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, "
> +                      "bytes = 0x%x, bits = 0x%x\n",
> +                      s->N1_bytes, s->N1_bits);
> +        s->N1_bytes = PNV_SPI_REG_SIZE;
> +        s->N1_bits = s->N1_bytes * 8;
> +    }
> +} /* end of calculate_N1 */
> +
> +/*
> + * Shift_N1 operation handler method
> + */
> +static bool operation_shiftn1(PnvSpi *s, uint8_t opcode,
> +                       PnvXferBuffer **payload, bool send_n1_alone)
> +{
> +    uint8_t n1_count;
> +    bool stop = false;
> +
> +    /*
> +     * If there isn't a current payload left over from a stopped
> sequence
> +     * create a new one.
> +     */
> +    if (*payload == NULL) {
> +        *payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Use a combination of N1 counters to build the N1 portion of
> the
> +     * transmit payload.
> +     * We only care about transmit at this time since the request
> payload
> +     * only represents data going out on the controller output line.
> +     * Leave mode specific considerations in the calculate function
> since
> +     * all we really care about are counters that tell use exactly
> how
> +     * many bytes are in the payload and how many of those bytes to
> +     * include from the TDR into the payload.
> +     */
> +    calculate_N1(s, opcode);
> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s-
> >N2_rx);
> +    /*
> +     * Zero out the N2 counters here in case there is no N2
> operation following
> +     * the N1 operation in the sequencer.  This keeps leftover N2
> information
> +     * from interfering with spi_response logic.
> +     */
> +    s->N2_bits = 0;
> +    s->N2_bytes = 0;
> +    s->N2_tx = 0;
> +    s->N2_rx = 0;
> +    /*
> +     * N1_bytes is the overall size of the N1 portion of the frame
> regardless of
> +     * whether N1 is used for tx, rx or both.  Loop over the size to
> build a
> +     * payload that is N1_bytes long.
> +     * N1_tx is the count of bytes to take from the TDR and "shift"
> into the
> +     * frame which means append those bytes to the payload for the
> N1 portion
> +     * of the frame.
> +     * If N1_tx is 0 or if the count exceeds the size of the TDR
> append 0xFF to
> +     * the frame until the overall N1 count is reached.
> +     */
> +    n1_count = 0;
> +    while (n1_count < s->N1_bytes) {
> +        /*
> +         * Assuming that if N1_tx is not equal to 0 then it is the
> same as
> +         * N1_bytes.
> +         */
> +        if ((s->N1_tx != 0) && (n1_count < PNV_SPI_REG_SIZE)) {
> +
> +            if (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1) {
> +                /*
> +                 * Note that we are only appending to the payload IF
> the TDR
> +                 * is full otherwise we don't touch the payload
> because we are
> +                 * going to NOT send the payload and instead tell
> the sequencer
> +                 * that called us to stop and wait for a TDR write
> so we have
> +                 * data to load into the payload.
> +                 */
> +                uint8_t n1_byte = 0x00;
> +                n1_byte = get_from_offset(s, n1_count);
> +                trace_pnv_spi_tx_append("n1_byte", n1_byte,
> n1_count);
> +                *(pnv_spi_xfer_buffer_write_ptr(*payload,
> (*payload)->len, 1)) =
> +                        n1_byte;
> +            } else {
> +                /*
> +                 * We hit a shift_n1 opcode TX but the TDR is empty,
> tell the
> +                 * sequencer to stop and break this loop.
> +                 */
> +                trace_pnv_spi_sequencer_stop_requested("Shift N1"
> +                                "set for transmit but TDR is
> empty");
> +                stop = true;
> +                break;
> +            }
> +        } else {
> +            /*
> +             * Cases here:
> +             * - we are receiving during the N1 frame segment and
> the RDR
> +             *   is full so we need to stop until the RDR is read
> +             * - we are transmitting and we don't care about RDR
> status
> +             *   since we won't be loading RDR during the frame
> segment.
> +             * - we are receiving and the RDR is empty so we allow
> the operation
> +             *   to proceed.
> +             */
> +            if ((s->N1_rx != 0) && (GETFIELD(SPI_STS_RDR_FULL,
> +                                           s->status) == 1)) {
> +                trace_pnv_spi_sequencer_stop_requested("shift N1"
> +                                "set for receive but RDR is full");
> +                stop = true;
> +                break;
> +            } else {
> +                trace_pnv_spi_tx_append_FF("n1_byte");
> +                *(pnv_spi_xfer_buffer_write_ptr(*payload,
> (*payload)->len, 1))
> +                        = 0xff;
> +            }
> +        }
> +        n1_count++;
> +    } /* end of while */
> +    /*
> +     * If we are not stopping due to an empty TDR and we are doing
> an N1 TX
> +     * and the TDR is full we need to clear the TDR_full status.
> +     * Do this here instead of up in the loop above so we don't log
> the message
> +     * in every loop iteration.
> +     * Ignore the send_n1_alone flag, all that does is defer the TX
> until the N2
> +     * operation, which was found immediately after the current
> opcode.  The TDR
> +     * was unloaded and will be shifted so we have to clear the
> TDR_full status.
> +     */
> +    if (!stop && (s->N1_tx != 0) &&
> +        (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
> +        s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
> +    }
> +    /*
> +     * There are other reasons why the shifter would stop, such as a
> TDR empty
> +     * or RDR full condition with N1 set to receive.  If we haven't
> stopped due
> +     * to either one of those conditions then check if the
> send_n1_alone flag is
> +     * equal to False, indicating the next opcode is an N2
> operation, AND if
> +     * the N2 counter reload switch (bit 0 of the N2 count control
> field) is
> +     * set.  This condition requires a pacing write to "kick" off
> the N2
> +     * shift which includes the N1 shift as well when send_n1_alone
> is False.
> +     */
> +    if (!stop && !send_n1_alone &&

Replace PPC_BIT(52) with defined name

> +       (GETFIELD(PPC_BIT(52), s->regs[SPI_CTR_CFG_REG]) == 1)) {
> +        trace_pnv_spi_sequencer_stop_requested("N2 counter reload "
> +                        "active, stop N1 shift, TDR_underrun set to
> 1");
> +        stop = true;
> +        s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 1);
> +    }
> +    /*
> +     * If send_n1_alone is set AND we have a full TDR then this is
> the first and
> +     * last payload to send and we don't have an N2 frame segment to
> add to the
> +     * payload.
> +     */
> +    if (send_n1_alone && !stop) {
> +        /* We have a TX and a full TDR or an RX and an empty RDR */
> +        trace_pnv_spi_tx_request("Shifting N1 frame", (*payload)-
> >len);
> +        transfer(s, *payload);
> +        /* The N1 frame shift is complete so reset the N1 counters
> */
> +        s->N2_bits = 0;
> +        s->N2_bytes = 0;
> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        pnv_spi_xfer_buffer_free(*payload);
> +        *payload = NULL;
> +    }
> +    return stop;
> +} /* end of operation_shiftn1() */
> +
> +/*
> + * Calculate the N2 counters based on passed in opcode and
> + * internal register values.
> + * The method assumes that the opcode is a Shift_N2 opcode
> + * and doesn't test it.
> + * The counters returned are:
> + * N2 bits: Number of bits in the payload data that are significant
> + * to the responder.
> + * N2_bytes: Total count of payload bytes for the N2 frame.
> + * N2_tx: Total number of bytes taken from TDR for N2
> + * N2_rx: Total number of bytes taken from the payload for N2
> + */
> +static void calculate_N2(PnvSpi *s, uint8_t opcode)
> +{
> +    /*
> +     * Shift_N2 opcode form: 0x4M
> +     * Implicit mode:
> +     * If M!=0 the shift count is M bytes and M is the number of rx
> bytes.
> +     * Forced Implicit mode:
> +     * M is the shift count but tx and rx is determined by the count
> control
> +     * register fields.  Note that we only check for Forced Implicit
> mode when
> +     * M != 0 since the mode doesn't make sense when M = 0.
> +     * Explicit mode:
> +     * If M==0 then shift count is number of bits defined in the
> +     * Counter Configuration Register's shift_count_N1 field.
> +     */

Replace GETFIELD below with new macro.

> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
> +        /* Explicit mode */
> +        s->N2_bits = GETFIELD(SPI_CTR_CFG_N2, s-
> >regs[SPI_CTR_CFG_REG]);
> +        s->N2_bytes = ceil(s->N2_bits / 8);


See above comment regarding use of the ceil function.


> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        /* If tx count control for N2 is set, load the tx value */

Replace PPC_BIT(54) and PPC_BIT(55) with defined names

> +        if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N2_tx = s->N2_bytes;
> +        }
> +        /* If rx count control for N2 is set, load the rx value */
> +        if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            s->N2_rx = s->N2_bytes;
> +        }
> +    } else {
> +        /* Implicit mode/Forced Implicit mode, use M field from
> opcode */

Replace GETFIELD below with new macro.

> +        s->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
> +        s->N2_bits = s->N2_bytes * 8;
> +        /* Assume that we are going to receive the count */
> +        s->N2_rx = s->N2_bytes;
> +        s->N2_tx = 0;
> +        /* Let Forced Implicit mode have an effect on the counts */

Replace PPC_BIT(53), PPC_BIT(55) and PPC_BIT(54) with defined names

> +        if (GETFIELD(PPC_BIT(53), s->regs[SPI_CTR_CFG_REG]) == 1) {
> +            /*
> +             * If Forced Implicit mode and count control doesn't
> +             * indicate a receive then reset the rx count to 0
> +             */
> +            if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) ==
> 0) {
> +                s->N2_rx = 0;
> +            }
> +            /* If tx count control for N2 is set, load the tx value
> */
> +            if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) ==
> 1) {
> +                s->N2_tx = s->N2_bytes;
> +            }
> +        }
> +    }
> +    /*
> +     * Enforce an upper limit on the size of N1 that is equal to the
> +     * known size of the shift register, 64 bits or 72 bits if ECC
> +     * is enabled.
> +     * If the size exceeds 72 bits it is a user error so log an
> error,
> +     * cap the size at a max of 64 bits or 72 bits and set the
> sequencer FSM
> +     * error bit.
> +     */

Use new SPI_CLK_CFG_ECC_CTRL mask below

> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
> +                                   s->regs[SPI_CLK_CFG_REG]);
> +    if (ecc_control == 0 || ecc_control == 2) {
> +        if (s->N2_bytes > (PNV_SPI_REG_SIZE + 1)) {
> +            /* Unsupported N2 shift size when ECC enabled */
> +            s->N2_bytes = PNV_SPI_REG_SIZE + 1;
> +            s->N2_bits = s->N2_bytes * 8;
> +        }
> +    } else if (s->N2_bytes > PNV_SPI_REG_SIZE) {
> +        /* Unsupported N2 shift size */
> +        s->N2_bytes = PNV_SPI_REG_SIZE;
> +        s->N2_bits = s->N2_bytes * 8;
> +    }
> +} /* end of calculate_N2 */
> +
> +/*
> + * Shift_N2 operation handler method
> + */
> +
> +static bool operation_shiftn2(PnvSpi *s, uint8_t opcode,
> +                       PnvXferBuffer **payload)
> +{
> +    uint8_t n2_count;
> +    bool stop = false;
> +
> +    /*
> +     * If there isn't a current payload left over from a stopped
> sequence
> +     * create a new one.
> +     */
> +    if (*payload == NULL) {
> +        *payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Use a combination of N2 counters to build the N2 portion of
> the
> +     * transmit payload.
> +     */
> +    calculate_N2(s, opcode);
> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s-
> >N2_rx);
> +    /*
> +     * The only difference between this code and the code for shift
> N1 is
> +     * that this code has to account for the possible presence of N1
> transmit
> +     * bytes already taken from the TDR.
> +     * If there are bytes to be transmitted for the N2 portion of
> the frame
> +     * and there are still bytes in TDR that have not been copied
> into the
> +     * TX data of the payload, this code will handle transmitting
> those
> +     * remaining bytes.
> +     * If for some reason the transmit count(s) add up to more than
> the size
> +     * of the TDR we will just append 0xFF to the transmit payload
> data until
> +     * the payload is N1 + N2 bytes long.
> +     */
> +    n2_count = 0;
> +    while (n2_count < s->N2_bytes) {
> +        /*
> +         * If the RDR is full and we need to RX just bail out,
> letting the
> +         * code continue will end up building the payload twice in
> the same
> +         * buffer since RDR full causes a sequence stop and restart.
> +         */
> +        if ((s->N2_rx != 0) &&
> +            (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1)) {
> +            trace_pnv_spi_sequencer_stop_requested("shift N2 set"
> +                            "for receive but RDR is full");
> +            stop = true;
> +            break;
> +        }
> +        if ((s->N2_tx != 0) && ((s->N1_tx + n2_count) <
> +                                PNV_SPI_REG_SIZE)) {
> +            /* Always append data for the N2 segment if it is set
> for TX */
> +            uint8_t n2_byte = 0x00;
> +            n2_byte = get_from_offset(s, (s->N1_tx + n2_count));
> +            trace_pnv_spi_tx_append("n2_byte", n2_byte, (s->N1_tx +
> n2_count));
> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)-
> >len, 1))
> +                    = n2_byte;
> +        } else {
> +            /*
> +             * Regardless of whether or not N2 is set for TX or RX,
> we need
> +             * the number of bytes in the payload to match the
> overall length
> +             * of the operation.
> +             */
> +            trace_pnv_spi_tx_append_FF("n2_byte");
> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)-
> >len, 1))
> +                    = 0xff;
> +        }
> +        n2_count++;
> +    } /* end of while */
> +    if (!stop) {
> +        /* We have a TX and a full TDR or an RX and an empty RDR */
> +        trace_pnv_spi_tx_request("Shifting N2 frame", (*payload)-
> >len);
> +        transfer(s, *payload);
> +        /*
> +         * If we are doing an N2 TX and the TDR is full we need to
> clear the
> +         * TDR_full status. Do this here instead of up in the loop
> above so we
> +         * don't log the message in every loop iteration.
> +         */
> +        if ((s->N2_tx != 0) &&
> +            (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
> +            s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
> +        }
> +        /*
> +         * The N2 frame shift is complete so reset the N2 counters.
> +         * Reset the N1 counters also in case the frame was a
> combination of
> +         * N1 and N2 segments.
> +         */
> +        s->N2_bits = 0;
> +        s->N2_bytes = 0;
> +        s->N2_tx = 0;
> +        s->N2_rx = 0;
> +        s->N1_bits = 0;
> +        s->N1_bytes = 0;
> +        s->N1_tx = 0;
> +        s->N1_rx = 0;
> +        pnv_spi_xfer_buffer_free(*payload);
> +        *payload = NULL;
> +    }
> +    return stop;
> +} /*  end of operation_shiftn2()*/
> +
> +static void operation_sequencer(PnvSpi *s)
> +{
> +    /*
> +     * Loop through each sequencer operation ID and perform the
> requested
> +     *  operations.
> +     * Flag for indicating if we should send the N1 frame or wait to
> combine
> +     * it with a preceding N2 frame.
> +     */
> +    bool send_n1_alone = true;
> +    bool stop = false; /* Flag to stop the sequencer */
> +    uint8_t opcode = 0;
> +    uint8_t masked_opcode = 0;
> +
> +    /*
> +     * PnvXferBuffer for containing the payload of the SPI frame.
> +     * This is a static because there are cases where a sequence has
> to stop
> +     * and wait for the target application to unload the RDR.  If
> this occurs
> +     * during a sequence where N1 is not sent alone and instead
> combined with
> +     * N2 since the N1 tx length + the N2 tx length is less than the
> size of
> +     * the TDR.
> +     */
> +    static PnvXferBuffer *payload;
> +
> +    if (payload == NULL) {
> +        payload = pnv_spi_xfer_buffer_new();
> +    }
> +    /*
> +     * Clear the sequencer FSM error bit - general_SPI_status[3]
> +     * before starting a sequence.
> +     */
> +    s->status = SETFIELD(PPC_BIT(35), s->status, 0);
> +    /*
> +     * If the FSM is idle set the sequencer index to 0
> +     * (new/restarted sequence)
> +     */
> +    if (GETFIELD(SPI_STS_SEQ_FSM, s->status) == SEQ_STATE_IDLE) {
> +        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
> +    }
> +    /*
> +     * There are only 8 possible operation IDs to iterate through
> though
> +     * some operations may cause more than one frame to be
> sequenced.
> +     */

Use a defined name instead of '8' below

> +    while (get_seq_index(s) < 8) {
> +        opcode = s->seq_op[get_seq_index(s)];
> +        /* Set sequencer state to decode */
> +        s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_DECODE);
> +        /*
> +         * Only the upper nibble of the operation ID is needed to
> know what
> +         * kind of operation is requested.
> +         */

Use macro to extract the opcode sequence below.  Something like
PNV_SPI_OPCODE_SEQ?

> +        masked_opcode = opcode & 0xF0;
> +        switch (masked_opcode) {
> +        /*
> +         * Increment the operation index in each case instead of
> just
> +         * once at the end in case an operation like the branch
> +         * operation needs to change the index.
> +         */
> +        case SEQ_OP_STOP:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            /* A stop operation in any position stops the sequencer
> */
> +            trace_pnv_spi_sequencer_op("STOP", get_seq_index(s));
> +
> +            stop = true;
> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> FSM_IDLE);
> +            s->loop_counter_1 = 0;
> +            s->loop_counter_2 = 0;
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_IDLE);
> +            break;
> +
> +        case SEQ_OP_SELECT_SLAVE:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SELECT_SLAVE",
> get_seq_index(s));
> +            /*
> +             * This device currently only supports a single
> responder
> +             * connection at position 0.  De-selecting a responder
> is fine
> +             * and expected at the end of a sequence but selecting
> any
> +             * responder other than 0 should cause an error.
> +             */

Use macro to extract opcode sequence below.

> +            s->responder_select = opcode & 0x0F;
> +            if (s->responder_select == 0) {
> +                trace_pnv_spi_shifter_done();
> +                qemu_set_irq(s->cs_line[0], 1);
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> +                                (get_seq_index(s) + 1));
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, 
> FSM_DONE);
> +            } else if (s->responder_select != 1) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Slave selection
> other than 1 "
> +                              "not supported, select = 0x%x\n",
> +                               s->responder_select);
> +                trace_pnv_spi_sequencer_stop_requested("invalid "
> +                                "responder select");
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, 
> FSM_IDLE);
> +                stop = true;
> +            } else {
> +                /*
> +                 * Only allow an FSM_START state when a responder is
> +                 * selected
> +                 */
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, 
> FSM_START);
> +                trace_pnv_spi_shifter_stating();
> +                qemu_set_irq(s->cs_line[0], 0);
> +                /*
> +                 * A Shift_N2 operation is only valid after a
> Shift_N1
> +                 * according to the spec. The spec doesn't say if
> that means
> +                 * immediately after or just after at any point. We
> will track
> +                 * the occurrence of a Shift_N1 to enforce this
> requirement in
> +                 * the most generic way possible by assuming that
> the rule
> +                 * applies once a valid responder select has
> occurred.
> +                 */
> +                s->shift_n1_done = false;
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        case SEQ_OP_SHIFT_N1:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SHIFT_N1",
> get_seq_index(s));
> +            /*
> +             * Only allow a shift_n1 when the state is not IDLE or
> DONE.
> +             * In either of those two cases the sequencer is not in
> a proper
> +             * state to perform shift operations because the
> sequencer has:
> +             * - processed a responder deselect (DONE)
> +             * - processed a stop opcode (IDLE)
> +             * - encountered an error (IDLE)
> +             */
> +            if ((GETFIELD(SPI_STS_SHIFTER_FSM, s->status) ==
> FSM_IDLE) ||
> +                (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) ==
> FSM_DONE)) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed
> in "
> +                              "shifter state = 0x%llx", GETFIELD(
> +                        SPI_STS_SHIFTER_FSM, s->status));
> +                /*
> +                 * Set sequencer FSM error bit 3
> (general_SPI_status[3])
> +                 * in status reg.
> +                 */

Replace PPC_BIT(35) with defined name below

> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
> +                trace_pnv_spi_sequencer_stop_requested("invalid
> shifter state");
> +                stop = true;
> +            } else {
> +                /*
> +                 * Look for the special case where there is a
> shift_n1 set for
> +                 * transmit and it is followed by a shift_n2 set for
> transmit
> +                 * AND the combined transmit length of the two
> operations is
> +                 * less than or equal to the size of the TDR
> register. In this
> +                 * case we want to use both this current shift_n1
> opcode and the
> +                 * following shift_n2 opcode to assemble the frame
> for
> +                 * transmission to the responder without requiring a
> refill of
> +                 * the TDR between the two operations.
> +                 */

Use a macro to extract the opcode sequence below.

> +                if ((s->seq_op[get_seq_index(s) + 1] & 0xF0)
> +                                == SEQ_OP_SHIFT_N2) {
> +                    send_n1_alone = false;
> +                }
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                FSM_SHIFT_N1);
> +                stop = operation_shiftn1(s, opcode, &payload,
> send_n1_alone);
> +                if (stop) {
> +                    /*
> +                     *  The operation code says to stop, this can
> occur if:
> +                     * (1) RDR is full and the N1 shift is set for
> receive
> +                     * (2) TDR was empty at the time of the N1 shift
> so we need
> +                     * to wait for data.
> +                     * (3) Neither 1 nor 2 are occurring and we
> aren't sending
> +                     * N1 alone and N2 counter reload is set (bit 0
> of the N2
> +                     * counter reload field).  In this case
> TDR_underrun will
> +                     * will be set and the Payload has been loaded
> so it is
> +                     * ok to advance the sequencer.
> +                     */
> +                    if (GETFIELD(SPI_STS_TDR_UNDERRUN, s->status)) {
> +                        s->shift_n1_done = true;
> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
> >status,
> +                                                  FSM_SHIFT_N2);
> +                        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s-
> >status,
> +                                        (get_seq_index(s) + 1));
> +                    } else {
> +                        /*
> +                         * This is case (1) or (2) so the sequencer
> needs to
> +                         * wait and NOT go to the next sequence yet.
> +                         */
> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
> >status,
> +                                        FSM_WAIT);
> +                    }
> +                } else {
> +                    /* Ok to move on to the next index */
> +                    s->shift_n1_done = true;
> +                    next_sequencer_fsm(s);
> +                }
> +            }
> +            break;
> +
> +        case SEQ_OP_SHIFT_N2:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("SHIFT_N2",
> get_seq_index(s));
> +            if (!s->shift_n1_done) {
> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not
> allowed if a "
> +                              "Shift_N1 is not done, shifter state =
> 0x%llx",
> +                              GETFIELD(SPI_STS_SHIFTER_FSM, s-
> >status));
> +                /*
> +                 * In case the sequencer actually stops if an N2
> shift is
> +                 * requested before any N1 shift is done. Set
> sequencer FSM
> +                 * error bit 3 (general_SPI_status[3]) in status
> reg.
> +                 */
> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
> +                trace_pnv_spi_sequencer_stop_requested("shift_n2 "
> +                                    "w/no shift_n1 done");
> +                stop = true;
> +            } else {
> +                /* Ok to do a Shift_N2 */
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> +                                FSM_SHIFT_N2);
> +                stop = operation_shiftn2(s, opcode, &payload);
> +                /*
> +                 * If the operation code says to stop set the
> shifter state to
> +                 * wait and stop
> +                 */
> +                if (stop) {
> +                    s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
> >status,
> +                                    FSM_WAIT);
> +                } else {
> +                    /* Ok to move on to the next index */
> +                    next_sequencer_fsm(s);
> +                }
> +            }
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_RDR:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_RDR",
> get_seq_index(s));
> +            /*
> +             * The memory mapping register RDR match value is
> compared against
> +             * the 16 rightmost bytes of the RDR (potentially with
> masking).
> +             * Since this comparison is performed against the
> contents of the
> +             * RDR then a receive must have previously occurred
> otherwise
> +             * there is no data to compare and the operation cannot
> be
> +             * completed and will stop the sequencer until RDR full
> is set to
> +             * 1.
> +             */
> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
> +                bool rdr_matched = false;
> +                rdr_matched = does_rdr_match(s);
> +                if (rdr_matched) {
> +                    trace_pnv_spi_RDR_match("success");
> +                    /* A match occurred, increment the sequencer
> index. */
> +                    next_sequencer_fsm(s);
> +                } else {
> +                    trace_pnv_spi_RDR_match("failed");
> +                    /*
> +                     * Branch the sequencer to the index coded into
> the op
> +                     * code.
> +                     */
> +                    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s-
> >status,

Use macro to extract opcode variable below.

> +                                    (opcode & 0x7));
> +                }
> +                /*
> +                 * Regardless of where the branch ended up we want
> the
> +                 * sequencer to continue shifting so we have to
> clear
> +                 * RDR_full.
> +                 */
> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status,
> 0);
> +            } else {
> +                trace_pnv_spi_sequencer_stop_requested("RDR not"
> +                                "full for 0x6x opcode");
> +                stop = true;
> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, 
> FSM_WAIT);
> +            }
> +            break;
> +
> +        case SEQ_OP_TRANSFER_TDR:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not
> supported\n");
> +            next_sequencer_fsm(s);
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_INC_1:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_1",
> get_seq_index(s));
> +            /*
> +             * The spec says the loop should execute count compare +
> 1 times.
> +             * However we learned from engineering that we really
> only loop
> +             * count_compare times, count compare = 0 makes this op
> code a
> +             * no-op
> +             */
> +            if (s->loop_counter_1 !=
> +                GETFIELD(SPI_CTR_CFG_CMP1, s-
> >regs[SPI_CTR_CFG_REG])) {
> +                /*
> +                 * Next index is the lower nibble of the branch
> operation ID,
> +                 * mask off all but the first three bits so we don't
> try to
> +                 * access beyond the sequencer_operation_reg
> boundary.
> +                 */
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,

Use macro to extract opcode variable below.

> +                                (opcode & 0x7));
> +                s->loop_counter_1++;
> +            } else {
> +                /* Continue to next index if loop counter is reached
> */
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        case SEQ_OP_BRANCH_IFNEQ_INC_2:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_2",
> get_seq_index(s));
> +            uint8_t condition2 = GETFIELD(SPI_CTR_CFG_CMP2,
> +                              s->regs[SPI_CTR_CFG_REG]);
> +            /*
> +             * The spec says the loop should execute count compare +
> 1 times.
> +             * However we learned from engineering that we really
> only loop
> +             * count_compare times, count compare = 0 makes this op
> code a
> +             * no-op
> +             */
> +            if (s->loop_counter_2 != condition2) {
> +                /*
> +                 * Next index is the lower nibble of the branch
> operation ID,
> +                 * mask off all but the first three bits so we don't
> try to
> +                 * access beyond the sequencer_operation_reg
> boundary.
> +                 */
> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,

Use macro to get opcode variable below

> +                                          (opcode & 0x7));
> +                s->loop_counter_2++;
> +            } else {
> +                /* Continue to next index if loop counter is reached
> */
> +                next_sequencer_fsm(s);
> +            }
> +            break;
> +
> +        default:
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_EXECUTE);
> +            /* Ignore unsupported operations. */
> +            next_sequencer_fsm(s);
> +            break;
> +        } /* end of switch */
> +        /*
> +         * If we used all 8 opcodes without seeing a 00 - STOP in
> the sequence
> +         * we need to go ahead and end things as if there was a STOP
> at the
> +         * end.

Use a defined name instead of `8` below.

> +        if (get_seq_index(s) == 8) {
> +            /* All 8 opcodes completed, sequencer idling */
> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
> FSM_IDLE);
> +            s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
> +            s->loop_counter_1 = 0;
> +            s->loop_counter_2 = 0;
> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
> SEQ_STATE_IDLE);
> +            break;
> +        }
> +        /* Break the loop if a stop was requested */
> +        if (stop) {
> +            break;
> +        }
> +    } /* end of while */
> +    return;
> +} /* end of operation_sequencer() */
> +
> +/*
> + * The SPIC engine and its internal sequencer can be interrupted and
> reset by
> + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive
> + * Miscellaneous Register of sbe_register_bo device.
> + * Reset immediately aborts any SPI transaction in progress and
> returns the
> + * sequencer and state machines to idle state.
> + * The configuration register values are not changed. The status
> register is
> + * not reset. The engine registers are not reset.
> + * The SPIC engine reset does not have any affect on the attached
> devices.
> + * Reset handling of any attached devices is beyond the scope of the
> engine.
> + */
> +static void do_reset(DeviceState *dev)
> +{
> +    PnvSpi *s = PNV_SPI(dev);
> +
> +    trace_pnv_spi_reset();
> +
> +    /* Reset all N1 and N2 counters, and other constants */
> +    s->N2_bits = 0;
> +    s->N2_bytes = 0;
> +    s->N2_tx = 0;
> +    s->N2_rx = 0;
> +    s->N1_bits = 0;
> +    s->N1_bytes = 0;
> +    s->N1_tx = 0;
> +    s->N1_rx = 0;
> +    s->loop_counter_1 = 0;
> +    s->loop_counter_2 = 0;
> +    /* Disconnected from responder */
> +    qemu_set_irq(s->cs_line[0], 1);
> +}
> +
>  static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr,
> unsigned size)
>  {
>      PnvSpi *s = PNV_SPI(opaque);
> @@ -36,6 +1067,10 @@ static uint64_t pnv_spi_xscom_read(void *opaque,
> hwaddr addr, unsigned size)
>          val = s->regs[reg];
>          trace_pnv_spi_read_RDR(val);
>          s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
> +        if (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_WAIT) {
> +            trace_pnv_spi_start_sequencer();
> +            operation_sequencer(s);
> +        }
>          break;
>      case SPI_SEQ_OP_REG:
>          val = 0;
> @@ -97,6 +1132,8 @@ static void pnv_spi_xscom_write(void *opaque,
> hwaddr addr,
>          trace_pnv_spi_write_TDR(val);
>          s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 1);
>          s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 0);
> +        trace_pnv_spi_start_sequencer();
> +        operation_sequencer(s);
>          break;
>      case SPI_SEQ_OP_REG:
>          for (int i = 0; i < PNV_SPI_REG_SIZE; i++) {
> @@ -129,6 +1166,7 @@ static const MemoryRegionOps pnv_spi_xscom_ops =
> {
>  
>  static Property pnv_spi_properties[] = {
>      DEFINE_PROP_UINT32("spic_num", PnvSpi, spic_num, 0),
> +    DEFINE_PROP_UINT8("transfer_len", PnvSpi, transfer_len, 4),
>      DEFINE_PROP_END_OF_LIST(),
>  };
>  
> @@ -180,6 +1218,7 @@ static void pnv_spi_class_init(ObjectClass
> *klass, void *data)
>  
>      dc->desc = "PowerNV SPI";
>      dc->realize = pnv_spi_realize;
> +    dc->reset = do_reset;
>      device_class_set_props(dc, pnv_spi_properties);
>  }
>  
> diff --git a/hw/ssi/trace-events b/hw/ssi/trace-events
> index 4388024a05..7fa27ebade 100644
> --- a/hw/ssi/trace-events
> +++ b/hw/ssi/trace-events
> @@ -38,3 +38,18 @@ pnv_spi_read(uint64_t addr, uint64_t val) "addr
> 0x%" PRIx64 " val 0x%" PRIx64
>  pnv_spi_write(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val
> 0x%" PRIx64
>  pnv_spi_read_RDR(uint64_t val) "data extracted = 0x%" PRIx64
>  pnv_spi_write_TDR(uint64_t val) "being written, data written = 0x%"
> PRIx64
> +pnv_spi_start_sequencer(void) ""
> +pnv_spi_reset(void) "spic engine sequencer configuration and spi
> communication"
> +pnv_spi_sequencer_op(const char* op, uint8_t index) "%s at index =
> 0x%x"
> +pnv_spi_shifter_stating(void) "pull CS line low"
> +pnv_spi_shifter_done(void) "pull the CS line high"
> +pnv_spi_log_Ncounts(uint8_t N1_bits, uint8_t N1_bytes, uint8_t
> N1_tx, uint8_t N1_rx, uint8_t N2_bits, uint8_t N2_bytes, uint8_t
> N2_tx, uint8_t N2_rx) "N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx
> = %d, N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d"
> +pnv_spi_tx_append(const char* frame, uint8_t byte, uint8_t
> tdr_index) "%s = 0x%2.2x to payload from TDR at index %d"
> +pnv_spi_tx_append_FF(const char* frame) "%s to Payload"
> +pnv_spi_tx_request(const char* frame, uint32_t payload_len) "%s,
> payload len = %d"
> +pnv_spi_rx_received(uint32_t payload_len) "payload len = %d"
> +pnv_spi_rx_read_N1frame(void) ""
> +pnv_spi_rx_read_N2frame(void) ""
> +pnv_spi_shift_rx(uint8_t byte, uint32_t index) "byte = 0x%2.2x into
> RDR from payload index %d"
> +pnv_spi_sequencer_stop_requested(const char* reason) "due to %s"
> +pnv_spi_RDR_match(const char* result) "%s"
Chalapathi V June 20, 2024, 1:25 p.m. UTC | #3
On 20-06-2024 03:44, Miles Glenn wrote:
> Hi Chalapathi,
>
> I can't say I have a great understanding of this IBM SPI controller,
> but I did find some places for improvement, mostly dealing with the use
> of "magic numbers" throughout the code.  Please see comments below.
>
> Thanks,
>
> Glenn

Hello Glenn,

Thank You for the review and suggestions. I will address them and update 
in next revision ASAP.

Thank You,

Chalapathi

>
> On Mon, 2024-06-17 at 11:54 -0500, Chalapathi V wrote:
>> In this commit SPI shift engine and sequencer logic is implemented.
>> Shift engine performs serialization and de-serialization according to
>> the
>> control by the sequencer and according to the setup defined in the
>> configuration registers. Sequencer implements the main control logic
>> and
>> FSM to handle data transmit and data receive control of the shift
>> engine.
>>
>> Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
>> ---
>>   include/hw/ssi/pnv_spi.h |   27 +
>>   hw/ssi/pnv_spi.c         | 1039
>> ++++++++++++++++++++++++++++++++++++++
>>   hw/ssi/trace-events      |   15 +
>>   3 files changed, 1081 insertions(+)
>>
>> diff --git a/include/hw/ssi/pnv_spi.h b/include/hw/ssi/pnv_spi.h
>> index 71c53d4a17..21fbfcb69c 100644
>> --- a/include/hw/ssi/pnv_spi.h
>> +++ b/include/hw/ssi/pnv_spi.h
>> @@ -8,6 +8,14 @@
>>    * This model Supports a connection to a single SPI responder.
>>    * Introduced for P10 to provide access to SPI seeproms, TPM, flash
>> device
>>    * and an ADC controller.
>> + *
>> + * All SPI function control is mapped into the SPI register space to
>> enable
>> + * full control by firmware.
>> + *
>> + * SPI Controller has sequencer and shift engine. The SPI shift
>> engine
>> + * performs serialization and de-serialization according to the
>> control by
>> + * the sequencer and according to the setup defined in the
>> configuration
>> + * registers and the SPI sequencer implements the main control
>> logic.
>>    */
>>   #include "hw/ssi/ssi.h"
>>   #include "hw/sysbus.h"
>> @@ -50,6 +58,25 @@ typedef struct PnvSpi {
>>       MemoryRegion    xscom_spic_regs;
>>       /* SPI object number */
>>       uint32_t        spic_num;
>> +    uint8_t         transfer_len;
>> +    uint8_t         responder_select;
>> +    /* To verify if shift_n1 happens prior to shift_n2 */
>> +    bool            shift_n1_done;
>> +    /* Loop counter for branch operation opcode Ex/Fx */
>> +    uint8_t         loop_counter_1;
>> +    uint8_t         loop_counter_2;
>> +    /* N1/N2_bits specifies the size of the N1/N2 segment of a frame
>> in bits.*/
>> +    uint8_t         N1_bits;
>> +    uint8_t         N2_bits;
>> +    /* Number of bytes in a payload for the N1/N2 frame segment.*/
>> +    uint8_t         N1_bytes;
>> +    uint8_t         N2_bytes;
>> +    /* Number of N1/N2 bytes marked for transmit */
>> +    uint8_t         N1_tx;
>> +    uint8_t         N2_tx;
>> +    /* Number of N1/N2 bytes marked for receive */
>> +    uint8_t         N1_rx;
>> +    uint8_t         N2_rx;
>>   
>>       /* SPI registers */
>>       uint64_t        regs[PNV_SPI_REGS];
>> diff --git a/hw/ssi/pnv_spi.c b/hw/ssi/pnv_spi.c
>> index da9e3925dd..b8f4370525 100644
>> --- a/hw/ssi/pnv_spi.c
>> +++ b/hw/ssi/pnv_spi.c
>> @@ -14,9 +14,1040 @@
>>   #include "hw/ssi/pnv_spi_regs.h"
>>   #include "hw/ssi/ssi.h"
>>   #include <libfdt.h>
>> +#include <math.h>
> I think the only reason you are including math.h is because you're
> using the `ceil` function below.  And, since you are only using it to
> operate on integers, it is not really necessary.  See comment below on
> how to do the same thing with integer math.
>
>>   #include "hw/irq.h"
>>   #include "trace.h"
>>   
>> +/* PnvXferBuffer */
>> +typedef struct PnvXferBuffer {
>> +
>> +    uint32_t    len;
>> +    uint8_t    *data;
>> +
>> +} PnvXferBuffer;
>> +
>> +/* pnv_spi_xfer_buffer_methods */
>> +static PnvXferBuffer *pnv_spi_xfer_buffer_new(void)
>> +{
>> +    PnvXferBuffer *payload = g_malloc0(sizeof(*payload));
>> +
>> +    return payload;
>> +}
>> +
>> +static void pnv_spi_xfer_buffer_free(PnvXferBuffer *payload)
>> +{
>> +    free(payload->data);
>> +    free(payload);
>> +}
>> +
>> +static uint8_t *pnv_spi_xfer_buffer_write_ptr(PnvXferBuffer
>> *payload,
>> +                uint32_t offset, uint32_t length)
>> +{
>> +    if (payload->len < (offset + length)) {
>> +        payload->len = offset + length;
>> +        payload->data = g_realloc(payload->data, payload->len);
>> +    }
>> +    return &payload->data[offset];
>> +}
>> +
>> +static bool does_rdr_match(PnvSpi *s)
>> +{
>> +    /*
>> +     * According to spec, the mask bits that are 0 are compared and
>> the
>> +     * bits that are 1 are ignored.
>> +     */
>> +    uint16_t rdr_match_mask = GETFIELD(SPI_MM_RDR_MATCH_MASK,
>> +                                        s->regs[SPI_MM_REG]);
>> +    uint16_t rdr_match_val = GETFIELD(SPI_MM_RDR_MATCH_VAL,
>> +                                        s->regs[SPI_MM_REG]);
>> +
>> +    if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) &
>> +            GETFIELD(PPC_BITMASK(48, 63), s-
>>> regs[SPI_RCV_DATA_REG]))) {
>> +        return true;
>> +    }
>> +    return false;
>> +}
>> +
>> +static uint8_t get_from_offset(PnvSpi *s, uint8_t offset)
>> +{
>> +    uint8_t byte;
>> +
>> +    /*
>> +     * Offset is an index between 0 and PNV_SPI_REG_SIZE - 1
>> +     * Check the offset before using it.
>> +     */
>> +    if (offset < PNV_SPI_REG_SIZE) {
>> +        byte = (s->regs[SPI_XMIT_DATA_REG] >> (56 - offset * 8)) &
>> 0xFF;
>> +    } else {
>> +        /*
>> +         * Log an error and return a 0xFF since we have to assign
>> something
>> +         * to byte before returning.
>> +         */
>> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to
>> get byte "
>> +                      "from TDR\n", offset);
>> +        byte = 0xff;
>> +    }
>> +    return byte;
>> +}
>> +
>> +static uint8_t read_from_frame(PnvSpi *s, uint8_t *read_buf, uint8_t
>> nr_bytes,
>> +                uint8_t ecc_count, uint8_t shift_in_count)
>> +{
>> +    uint8_t byte;
>> +    int count = 0;
>> +
>> +    while (count < nr_bytes) {
>> +        shift_in_count++;
>> +        if ((ecc_count != 0) &&
>> +            (shift_in_count == (PNV_SPI_REG_SIZE + ecc_count))) {
>> +            shift_in_count = 0;
>> +        } else {
>> +            byte = read_buf[count];
>> +            trace_pnv_spi_shift_rx(byte, count);
>> +            s->regs[SPI_RCV_DATA_REG] = (s->regs[SPI_RCV_DATA_REG]
>> << 8) | byte;
>> +        }
>> +        count++;
>> +    } /* end of while */
>> +    return shift_in_count;
>> +}
>> +
>> +static void spi_response(PnvSpi *s, int bits, PnvXferBuffer
>> *rsp_payload)
>> +{
>> +    uint8_t ecc_count;
>> +    uint8_t shift_in_count;
>> +
>> +    /*
>> +     * Processing here must handle:
>> +     * - Which bytes in the payload we should move to the RDR
>> +     * - Explicit mode counter configuration settings
>> +     * - RDR full and RDR overrun status
>> +     */
>> +
>> +    /*
>> +     * First check that the response payload is the exact same
>> +     * number of bytes as the request payload was
>> +     */
>> +    if (rsp_payload->len != (s->N1_bytes + s->N2_bytes)) {
>> +        qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload
>> size in "
>> +                       "bytes, expected %d, got %d\n",
>> +                       (s->N1_bytes + s->N2_bytes), rsp_payload-
>>> len);
>> +    } else {
>> +        uint8_t ecc_control;
>> +        trace_pnv_spi_rx_received(rsp_payload->len);
>> +        trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
>> +                        s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx,
>> s->N2_rx);
>> +        /*
>> +         * Adding an ECC count let's us know when we have found a
>> payload byte
>> +         * that was shifted in but cannot be loaded into RDR.  Bits
>> 29-30 of
>> +         * clock_config_reset_control register equal to either 0b00
>> or 0b10
>> +         * indicate that we are taking in data with ECC and either
>> applying
>> +         * the ECC or discarding it.
>> +         */
>> +        ecc_count = 0;
> I think you're not using the SPI_CLK_CFG_ECC_CTRL mask here because it
> also includes bit 28 and you only need bits 29 and 30.  It would be
> better if you split the SPI_CLK_CFG_ECC_CTRL mask into two masks like
> this:
>
> #define SPI_CLK_CFG_ECC_EN    PPC_BIT(28)
> #define SPI_CLK_CFG_ECC_CTRL  PPC_BITMASK(29, 30)
>
> Then, use SPI_CLK_CFG_ECC_CTRL below.
>
>> +        ecc_control = GETFIELD(PPC_BITMASK(29, 30), s-
>>> regs[SPI_CLK_CFG_REG]);
>> +        if (ecc_control == 0 || ecc_control == 2) {
>> +            ecc_count = 1;
>> +        }
>> +        /*
>> +         * Use the N1_rx and N2_rx counts to control shifting data
>> from the
>> +         * payload into the RDR.  Keep an overall count of the
>> number of bytes
>> +         * shifted into RDR so we can discard every 9th byte when
>> ECC is
>> +         * enabled.
>> +         */
>> +        shift_in_count = 0;
>> +        /* Handle the N1 portion of the frame first */
>> +        if (s->N1_rx != 0) {
>> +            trace_pnv_spi_rx_read_N1frame();
>> +            shift_in_count = read_from_frame(s, &rsp_payload-
>>> data[0],
>> +                            s->N1_bytes, ecc_count, shift_in_count);
>> +        }
>> +        /* Handle the N2 portion of the frame */
>> +        if (s->N2_rx != 0) {
>> +            trace_pnv_spi_rx_read_N2frame();
>> +            shift_in_count = read_from_frame(s,
>> +                            &rsp_payload->data[s->N1_bytes], s-
>>> N2_bytes,
>> +                            ecc_count, shift_in_count);
>> +        }
>> +        if ((s->N1_rx + s->N2_rx) > 0) {
>> +            /*
>> +             * Data was received so handle RDR status.
>> +             * It is easier to handle RDR_full and RDR_overrun
>> status here
>> +             * since the RDR register's shift_byte_in method is
>> called
>> +             * multiple times in a row. Controlling RDR status is
>> done here
>> +             * instead of in the RDR scoped methods for that reason.
>> +             */
>> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
>> +                /*
>> +                 * Data was shifted into the RDR before having been
>> read
>> +                 * causing previous data to have been overrun.
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_RDR_OVERRUN, s->status,
>> 1);
>> +            } else {
>> +                /*
>> +                 * Set status to indicate that the received data
>> register is
>> +                 * full. This flag is only cleared once the RDR is
>> unloaded.
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status,
>> 1);
>> +            }
>> +        }
>> +    } /* end of else */
>> +} /* end of spi_response() */
>> +
>> +static void transfer(PnvSpi *s, PnvXferBuffer *payload)
>> +{
>> +    uint32_t tx;
>> +    uint32_t rx;
>> +    PnvXferBuffer *rsp_payload = NULL;
>> +
>> +    rsp_payload = pnv_spi_xfer_buffer_new();
>> +    for (int offset = 0; offset < payload->len; offset += s-
>>> transfer_len) {
>> +        tx = 0;
>> +        for (int i = 0; i < s->transfer_len; i++) {
>> +            if ((offset + i) >= payload->len) {
>> +                tx <<= 8;
>> +            } else {
>> +                tx = (tx << 8) | payload->data[offset + i];
>> +            }
>> +        }
>> +        rx = ssi_transfer(s->ssi_bus, tx);
>> +        for (int i = 0; i < s->transfer_len; i++) {
>> +            if ((offset + i) >= payload->len) {
>> +                break;
>> +            }
>> +            *(pnv_spi_xfer_buffer_write_ptr(rsp_payload,
>> rsp_payload->len, 1)) =
>> +                    (rx >> (8 * (s->transfer_len - 1) - i * 8)) &
>> 0xFF;
>> +        }
>> +    }
>> +    if (rsp_payload != NULL) {
>> +        spi_response(s, s->N1_bits, rsp_payload);
>> +    }
>> +}
>> +
>> +static inline uint8_t get_seq_index(PnvSpi *s)
>> +{
>> +    return GETFIELD(SPI_STS_SEQ_INDEX, s->status);
>> +}
>> +
>> +static inline void next_sequencer_fsm(PnvSpi *s)
>> +{
>> +    uint8_t seq_index = get_seq_index(s);
>> +    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, (seq_index +
>> 1));
>> +    s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_INDEX_INCREMENT);
>> +}
>> +
>> +/*
>> + * Calculate the N1 counters based on passed in opcode and
>> + * internal register values.
>> + * The method assumes that the opcode is a Shift_N1 opcode
>> + * and doesn't test it.
>> + * The counters returned are:
>> + * N1 bits: Number of bits in the payload data that are significant
>> + * to the responder.
>> + * N1_bytes: Total count of payload bytes for the N1 (portion of
>> the) frame.
>> + * N1_tx: Total number of bytes taken from TDR for N1
>> + * N1_rx: Total number of bytes taken from the payload for N1
>> + */
>> +static void calculate_N1(PnvSpi *s, uint8_t opcode)
>> +{
>> +    /*
>> +     * Shift_N1 opcode form: 0x3M
>> +     * Implicit mode:
>> +     * If M != 0 the shift count is M bytes and M is the number of
>> tx bytes.
>> +     * Forced Implicit mode:
>> +     * M is the shift count but tx and rx is determined by the count
>> control
>> +     * register fields.  Note that we only check for forced Implicit
>> mode when
>> +     * M != 0 since the mode doesn't make sense when M = 0.
>> +     * Explicit mode:
>> +     * If M == 0 then shift count is number of bits defined in the
>> +     * Counter Configuration Register's shift_count_N1 field.
>> +     */
> Please write a macro to extract the opcode variable out of the opcode
> and use it here.  You could call it PNV_SPI_OPCODE_VAR or something
> like that.
>
>> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
>> +        /* Explicit mode */
>> +        s->N1_bits = GETFIELD(SPI_CTR_CFG_N1, s-
>>> regs[SPI_CTR_CFG_REG]);
>> +        s->N1_bytes = ceil(s->N1_bits / 8);
> I think your use of the ceil function above is probably not doing what
> you think it should.  N1_bits is an integer and when you divide it by
> another integer, 8, I believe it results in another integer without the
> decimal part.  This integer will then be converted to a double, which
> is what ceil takes.  So, as is, I think you're still getting the floor
> value.  Regardless, instead of using ceil, which requires pulling in
> the math library, I suggest you use the following integer math:
>
> s->N1_bytes = (s->N1_bits + 7) / 8;
>
>
>> +        s->N1_tx = 0;
>> +        s->N1_rx = 0;
>> +        /* If tx count control for N1 is set, load the tx value */
> Replace PPC_BIT(50) and PPC_BIT(51) with defined names below
>
>> +        if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            s->N1_tx = s->N1_bytes;
>> +        }
>> +        /* If rx count control for N1 is set, load the rx value */
>> +        if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            s->N1_rx = s->N1_bytes;
>> +        }
>> +    } else {
>> +        /* Implicit mode/Forced Implicit mode, use M field from
>> opcode */
> Replace GETFIELD below with new macro.
>
>> +        s->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
>> +        s->N1_bits = s->N1_bytes * 8;
>> +        /*
>> +         * Assume that we are going to transmit the count
>> +         * (pure Implicit only)
>> +         */
>> +        s->N1_tx = s->N1_bytes;
>> +        s->N1_rx = 0;
> Replace PPC_BIT(49), PPC_BIT(50), and PPC_BIT(51) with defined names
>
>> +        /* Let Forced Implicit mode have an effect on the counts */
>> +        if (GETFIELD(PPC_BIT(49), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            /*
>> +             * If Forced Implicit mode and count control doesn't
>> +             * indicate transmit then reset the tx count to 0
>> +             */
>> +            if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) ==
>> 0) {
>> +                s->N1_tx = 0;
>> +            }
>> +            /* If rx count control for N1 is set, load the rx value
>> */
>> +            if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) ==
>> 1) {
>> +                s->N1_rx = s->N1_bytes;
>> +            }
>> +        }
>> +    }
>> +    /*
>> +     * Enforce an upper limit on the size of N1 that is equal to the
>> known size
>> +     * of the shift register, 64 bits or 72 bits if ECC is enabled.
>> +     * If the size exceeds 72 bits it is a user error so log an
>> error,
>> +     * cap the size at a max of 64 bits or 72 bits and set the
>> sequencer FSM
>> +     * error bit.
>> +     */
> Use new SPI_CLK_CFG_ECC_CTRL mask below
>
>> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
>> +                                   s->regs[SPI_CLK_CFG_REG]);
>> +    if (ecc_control == 0 || ecc_control == 2) {
>> +        if (s->N1_bytes > (PNV_SPI_REG_SIZE + 1)) {
>> +            qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift
>> size when "
>> +                          "ECC enabled, bytes = 0x%x, bits =
>> 0x%x\n",
>> +                          s->N1_bytes, s->N1_bits);
>> +            s->N1_bytes = PNV_SPI_REG_SIZE + 1;
>> +            s->N1_bits = s->N1_bytes * 8;
>> +        }
>> +    } else if (s->N1_bytes > PNV_SPI_REG_SIZE) {
>> +        qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, "
>> +                      "bytes = 0x%x, bits = 0x%x\n",
>> +                      s->N1_bytes, s->N1_bits);
>> +        s->N1_bytes = PNV_SPI_REG_SIZE;
>> +        s->N1_bits = s->N1_bytes * 8;
>> +    }
>> +} /* end of calculate_N1 */
>> +
>> +/*
>> + * Shift_N1 operation handler method
>> + */
>> +static bool operation_shiftn1(PnvSpi *s, uint8_t opcode,
>> +                       PnvXferBuffer **payload, bool send_n1_alone)
>> +{
>> +    uint8_t n1_count;
>> +    bool stop = false;
>> +
>> +    /*
>> +     * If there isn't a current payload left over from a stopped
>> sequence
>> +     * create a new one.
>> +     */
>> +    if (*payload == NULL) {
>> +        *payload = pnv_spi_xfer_buffer_new();
>> +    }
>> +    /*
>> +     * Use a combination of N1 counters to build the N1 portion of
>> the
>> +     * transmit payload.
>> +     * We only care about transmit at this time since the request
>> payload
>> +     * only represents data going out on the controller output line.
>> +     * Leave mode specific considerations in the calculate function
>> since
>> +     * all we really care about are counters that tell use exactly
>> how
>> +     * many bytes are in the payload and how many of those bytes to
>> +     * include from the TDR into the payload.
>> +     */
>> +    calculate_N1(s, opcode);
>> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
>> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s-
>>> N2_rx);
>> +    /*
>> +     * Zero out the N2 counters here in case there is no N2
>> operation following
>> +     * the N1 operation in the sequencer.  This keeps leftover N2
>> information
>> +     * from interfering with spi_response logic.
>> +     */
>> +    s->N2_bits = 0;
>> +    s->N2_bytes = 0;
>> +    s->N2_tx = 0;
>> +    s->N2_rx = 0;
>> +    /*
>> +     * N1_bytes is the overall size of the N1 portion of the frame
>> regardless of
>> +     * whether N1 is used for tx, rx or both.  Loop over the size to
>> build a
>> +     * payload that is N1_bytes long.
>> +     * N1_tx is the count of bytes to take from the TDR and "shift"
>> into the
>> +     * frame which means append those bytes to the payload for the
>> N1 portion
>> +     * of the frame.
>> +     * If N1_tx is 0 or if the count exceeds the size of the TDR
>> append 0xFF to
>> +     * the frame until the overall N1 count is reached.
>> +     */
>> +    n1_count = 0;
>> +    while (n1_count < s->N1_bytes) {
>> +        /*
>> +         * Assuming that if N1_tx is not equal to 0 then it is the
>> same as
>> +         * N1_bytes.
>> +         */
>> +        if ((s->N1_tx != 0) && (n1_count < PNV_SPI_REG_SIZE)) {
>> +
>> +            if (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1) {
>> +                /*
>> +                 * Note that we are only appending to the payload IF
>> the TDR
>> +                 * is full otherwise we don't touch the payload
>> because we are
>> +                 * going to NOT send the payload and instead tell
>> the sequencer
>> +                 * that called us to stop and wait for a TDR write
>> so we have
>> +                 * data to load into the payload.
>> +                 */
>> +                uint8_t n1_byte = 0x00;
>> +                n1_byte = get_from_offset(s, n1_count);
>> +                trace_pnv_spi_tx_append("n1_byte", n1_byte,
>> n1_count);
>> +                *(pnv_spi_xfer_buffer_write_ptr(*payload,
>> (*payload)->len, 1)) =
>> +                        n1_byte;
>> +            } else {
>> +                /*
>> +                 * We hit a shift_n1 opcode TX but the TDR is empty,
>> tell the
>> +                 * sequencer to stop and break this loop.
>> +                 */
>> +                trace_pnv_spi_sequencer_stop_requested("Shift N1"
>> +                                "set for transmit but TDR is
>> empty");
>> +                stop = true;
>> +                break;
>> +            }
>> +        } else {
>> +            /*
>> +             * Cases here:
>> +             * - we are receiving during the N1 frame segment and
>> the RDR
>> +             *   is full so we need to stop until the RDR is read
>> +             * - we are transmitting and we don't care about RDR
>> status
>> +             *   since we won't be loading RDR during the frame
>> segment.
>> +             * - we are receiving and the RDR is empty so we allow
>> the operation
>> +             *   to proceed.
>> +             */
>> +            if ((s->N1_rx != 0) && (GETFIELD(SPI_STS_RDR_FULL,
>> +                                           s->status) == 1)) {
>> +                trace_pnv_spi_sequencer_stop_requested("shift N1"
>> +                                "set for receive but RDR is full");
>> +                stop = true;
>> +                break;
>> +            } else {
>> +                trace_pnv_spi_tx_append_FF("n1_byte");
>> +                *(pnv_spi_xfer_buffer_write_ptr(*payload,
>> (*payload)->len, 1))
>> +                        = 0xff;
>> +            }
>> +        }
>> +        n1_count++;
>> +    } /* end of while */
>> +    /*
>> +     * If we are not stopping due to an empty TDR and we are doing
>> an N1 TX
>> +     * and the TDR is full we need to clear the TDR_full status.
>> +     * Do this here instead of up in the loop above so we don't log
>> the message
>> +     * in every loop iteration.
>> +     * Ignore the send_n1_alone flag, all that does is defer the TX
>> until the N2
>> +     * operation, which was found immediately after the current
>> opcode.  The TDR
>> +     * was unloaded and will be shifted so we have to clear the
>> TDR_full status.
>> +     */
>> +    if (!stop && (s->N1_tx != 0) &&
>> +        (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
>> +        s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
>> +    }
>> +    /*
>> +     * There are other reasons why the shifter would stop, such as a
>> TDR empty
>> +     * or RDR full condition with N1 set to receive.  If we haven't
>> stopped due
>> +     * to either one of those conditions then check if the
>> send_n1_alone flag is
>> +     * equal to False, indicating the next opcode is an N2
>> operation, AND if
>> +     * the N2 counter reload switch (bit 0 of the N2 count control
>> field) is
>> +     * set.  This condition requires a pacing write to "kick" off
>> the N2
>> +     * shift which includes the N1 shift as well when send_n1_alone
>> is False.
>> +     */
>> +    if (!stop && !send_n1_alone &&
> Replace PPC_BIT(52) with defined name
>
>> +       (GETFIELD(PPC_BIT(52), s->regs[SPI_CTR_CFG_REG]) == 1)) {
>> +        trace_pnv_spi_sequencer_stop_requested("N2 counter reload "
>> +                        "active, stop N1 shift, TDR_underrun set to
>> 1");
>> +        stop = true;
>> +        s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 1);
>> +    }
>> +    /*
>> +     * If send_n1_alone is set AND we have a full TDR then this is
>> the first and
>> +     * last payload to send and we don't have an N2 frame segment to
>> add to the
>> +     * payload.
>> +     */
>> +    if (send_n1_alone && !stop) {
>> +        /* We have a TX and a full TDR or an RX and an empty RDR */
>> +        trace_pnv_spi_tx_request("Shifting N1 frame", (*payload)-
>>> len);
>> +        transfer(s, *payload);
>> +        /* The N1 frame shift is complete so reset the N1 counters
>> */
>> +        s->N2_bits = 0;
>> +        s->N2_bytes = 0;
>> +        s->N2_tx = 0;
>> +        s->N2_rx = 0;
>> +        pnv_spi_xfer_buffer_free(*payload);
>> +        *payload = NULL;
>> +    }
>> +    return stop;
>> +} /* end of operation_shiftn1() */
>> +
>> +/*
>> + * Calculate the N2 counters based on passed in opcode and
>> + * internal register values.
>> + * The method assumes that the opcode is a Shift_N2 opcode
>> + * and doesn't test it.
>> + * The counters returned are:
>> + * N2 bits: Number of bits in the payload data that are significant
>> + * to the responder.
>> + * N2_bytes: Total count of payload bytes for the N2 frame.
>> + * N2_tx: Total number of bytes taken from TDR for N2
>> + * N2_rx: Total number of bytes taken from the payload for N2
>> + */
>> +static void calculate_N2(PnvSpi *s, uint8_t opcode)
>> +{
>> +    /*
>> +     * Shift_N2 opcode form: 0x4M
>> +     * Implicit mode:
>> +     * If M!=0 the shift count is M bytes and M is the number of rx
>> bytes.
>> +     * Forced Implicit mode:
>> +     * M is the shift count but tx and rx is determined by the count
>> control
>> +     * register fields.  Note that we only check for Forced Implicit
>> mode when
>> +     * M != 0 since the mode doesn't make sense when M = 0.
>> +     * Explicit mode:
>> +     * If M==0 then shift count is number of bits defined in the
>> +     * Counter Configuration Register's shift_count_N1 field.
>> +     */
> Replace GETFIELD below with new macro.
>
>> +    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
>> +        /* Explicit mode */
>> +        s->N2_bits = GETFIELD(SPI_CTR_CFG_N2, s-
>>> regs[SPI_CTR_CFG_REG]);
>> +        s->N2_bytes = ceil(s->N2_bits / 8);
>
> See above comment regarding use of the ceil function.
>
>
>> +        s->N2_tx = 0;
>> +        s->N2_rx = 0;
>> +        /* If tx count control for N2 is set, load the tx value */
> Replace PPC_BIT(54) and PPC_BIT(55) with defined names
>
>> +        if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            s->N2_tx = s->N2_bytes;
>> +        }
>> +        /* If rx count control for N2 is set, load the rx value */
>> +        if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            s->N2_rx = s->N2_bytes;
>> +        }
>> +    } else {
>> +        /* Implicit mode/Forced Implicit mode, use M field from
>> opcode */
> Replace GETFIELD below with new macro.
>
>> +        s->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
>> +        s->N2_bits = s->N2_bytes * 8;
>> +        /* Assume that we are going to receive the count */
>> +        s->N2_rx = s->N2_bytes;
>> +        s->N2_tx = 0;
>> +        /* Let Forced Implicit mode have an effect on the counts */
> Replace PPC_BIT(53), PPC_BIT(55) and PPC_BIT(54) with defined names
>
>> +        if (GETFIELD(PPC_BIT(53), s->regs[SPI_CTR_CFG_REG]) == 1) {
>> +            /*
>> +             * If Forced Implicit mode and count control doesn't
>> +             * indicate a receive then reset the rx count to 0
>> +             */
>> +            if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) ==
>> 0) {
>> +                s->N2_rx = 0;
>> +            }
>> +            /* If tx count control for N2 is set, load the tx value
>> */
>> +            if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) ==
>> 1) {
>> +                s->N2_tx = s->N2_bytes;
>> +            }
>> +        }
>> +    }
>> +    /*
>> +     * Enforce an upper limit on the size of N1 that is equal to the
>> +     * known size of the shift register, 64 bits or 72 bits if ECC
>> +     * is enabled.
>> +     * If the size exceeds 72 bits it is a user error so log an
>> error,
>> +     * cap the size at a max of 64 bits or 72 bits and set the
>> sequencer FSM
>> +     * error bit.
>> +     */
> Use new SPI_CLK_CFG_ECC_CTRL mask below
>
>> +    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
>> +                                   s->regs[SPI_CLK_CFG_REG]);
>> +    if (ecc_control == 0 || ecc_control == 2) {
>> +        if (s->N2_bytes > (PNV_SPI_REG_SIZE + 1)) {
>> +            /* Unsupported N2 shift size when ECC enabled */
>> +            s->N2_bytes = PNV_SPI_REG_SIZE + 1;
>> +            s->N2_bits = s->N2_bytes * 8;
>> +        }
>> +    } else if (s->N2_bytes > PNV_SPI_REG_SIZE) {
>> +        /* Unsupported N2 shift size */
>> +        s->N2_bytes = PNV_SPI_REG_SIZE;
>> +        s->N2_bits = s->N2_bytes * 8;
>> +    }
>> +} /* end of calculate_N2 */
>> +
>> +/*
>> + * Shift_N2 operation handler method
>> + */
>> +
>> +static bool operation_shiftn2(PnvSpi *s, uint8_t opcode,
>> +                       PnvXferBuffer **payload)
>> +{
>> +    uint8_t n2_count;
>> +    bool stop = false;
>> +
>> +    /*
>> +     * If there isn't a current payload left over from a stopped
>> sequence
>> +     * create a new one.
>> +     */
>> +    if (*payload == NULL) {
>> +        *payload = pnv_spi_xfer_buffer_new();
>> +    }
>> +    /*
>> +     * Use a combination of N2 counters to build the N2 portion of
>> the
>> +     * transmit payload.
>> +     */
>> +    calculate_N2(s, opcode);
>> +    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
>> +                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s-
>>> N2_rx);
>> +    /*
>> +     * The only difference between this code and the code for shift
>> N1 is
>> +     * that this code has to account for the possible presence of N1
>> transmit
>> +     * bytes already taken from the TDR.
>> +     * If there are bytes to be transmitted for the N2 portion of
>> the frame
>> +     * and there are still bytes in TDR that have not been copied
>> into the
>> +     * TX data of the payload, this code will handle transmitting
>> those
>> +     * remaining bytes.
>> +     * If for some reason the transmit count(s) add up to more than
>> the size
>> +     * of the TDR we will just append 0xFF to the transmit payload
>> data until
>> +     * the payload is N1 + N2 bytes long.
>> +     */
>> +    n2_count = 0;
>> +    while (n2_count < s->N2_bytes) {
>> +        /*
>> +         * If the RDR is full and we need to RX just bail out,
>> letting the
>> +         * code continue will end up building the payload twice in
>> the same
>> +         * buffer since RDR full causes a sequence stop and restart.
>> +         */
>> +        if ((s->N2_rx != 0) &&
>> +            (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1)) {
>> +            trace_pnv_spi_sequencer_stop_requested("shift N2 set"
>> +                            "for receive but RDR is full");
>> +            stop = true;
>> +            break;
>> +        }
>> +        if ((s->N2_tx != 0) && ((s->N1_tx + n2_count) <
>> +                                PNV_SPI_REG_SIZE)) {
>> +            /* Always append data for the N2 segment if it is set
>> for TX */
>> +            uint8_t n2_byte = 0x00;
>> +            n2_byte = get_from_offset(s, (s->N1_tx + n2_count));
>> +            trace_pnv_spi_tx_append("n2_byte", n2_byte, (s->N1_tx +
>> n2_count));
>> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)-
>>> len, 1))
>> +                    = n2_byte;
>> +        } else {
>> +            /*
>> +             * Regardless of whether or not N2 is set for TX or RX,
>> we need
>> +             * the number of bytes in the payload to match the
>> overall length
>> +             * of the operation.
>> +             */
>> +            trace_pnv_spi_tx_append_FF("n2_byte");
>> +            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)-
>>> len, 1))
>> +                    = 0xff;
>> +        }
>> +        n2_count++;
>> +    } /* end of while */
>> +    if (!stop) {
>> +        /* We have a TX and a full TDR or an RX and an empty RDR */
>> +        trace_pnv_spi_tx_request("Shifting N2 frame", (*payload)-
>>> len);
>> +        transfer(s, *payload);
>> +        /*
>> +         * If we are doing an N2 TX and the TDR is full we need to
>> clear the
>> +         * TDR_full status. Do this here instead of up in the loop
>> above so we
>> +         * don't log the message in every loop iteration.
>> +         */
>> +        if ((s->N2_tx != 0) &&
>> +            (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
>> +            s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
>> +        }
>> +        /*
>> +         * The N2 frame shift is complete so reset the N2 counters.
>> +         * Reset the N1 counters also in case the frame was a
>> combination of
>> +         * N1 and N2 segments.
>> +         */
>> +        s->N2_bits = 0;
>> +        s->N2_bytes = 0;
>> +        s->N2_tx = 0;
>> +        s->N2_rx = 0;
>> +        s->N1_bits = 0;
>> +        s->N1_bytes = 0;
>> +        s->N1_tx = 0;
>> +        s->N1_rx = 0;
>> +        pnv_spi_xfer_buffer_free(*payload);
>> +        *payload = NULL;
>> +    }
>> +    return stop;
>> +} /*  end of operation_shiftn2()*/
>> +
>> +static void operation_sequencer(PnvSpi *s)
>> +{
>> +    /*
>> +     * Loop through each sequencer operation ID and perform the
>> requested
>> +     *  operations.
>> +     * Flag for indicating if we should send the N1 frame or wait to
>> combine
>> +     * it with a preceding N2 frame.
>> +     */
>> +    bool send_n1_alone = true;
>> +    bool stop = false; /* Flag to stop the sequencer */
>> +    uint8_t opcode = 0;
>> +    uint8_t masked_opcode = 0;
>> +
>> +    /*
>> +     * PnvXferBuffer for containing the payload of the SPI frame.
>> +     * This is a static because there are cases where a sequence has
>> to stop
>> +     * and wait for the target application to unload the RDR.  If
>> this occurs
>> +     * during a sequence where N1 is not sent alone and instead
>> combined with
>> +     * N2 since the N1 tx length + the N2 tx length is less than the
>> size of
>> +     * the TDR.
>> +     */
>> +    static PnvXferBuffer *payload;
>> +
>> +    if (payload == NULL) {
>> +        payload = pnv_spi_xfer_buffer_new();
>> +    }
>> +    /*
>> +     * Clear the sequencer FSM error bit - general_SPI_status[3]
>> +     * before starting a sequence.
>> +     */
>> +    s->status = SETFIELD(PPC_BIT(35), s->status, 0);
>> +    /*
>> +     * If the FSM is idle set the sequencer index to 0
>> +     * (new/restarted sequence)
>> +     */
>> +    if (GETFIELD(SPI_STS_SEQ_FSM, s->status) == SEQ_STATE_IDLE) {
>> +        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
>> +    }
>> +    /*
>> +     * There are only 8 possible operation IDs to iterate through
>> though
>> +     * some operations may cause more than one frame to be
>> sequenced.
>> +     */
> Use a defined name instead of '8' below
>
>> +    while (get_seq_index(s) < 8) {
>> +        opcode = s->seq_op[get_seq_index(s)];
>> +        /* Set sequencer state to decode */
>> +        s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_DECODE);
>> +        /*
>> +         * Only the upper nibble of the operation ID is needed to
>> know what
>> +         * kind of operation is requested.
>> +         */
> Use macro to extract the opcode sequence below.  Something like
> PNV_SPI_OPCODE_SEQ?
>
>> +        masked_opcode = opcode & 0xF0;
>> +        switch (masked_opcode) {
>> +        /*
>> +         * Increment the operation index in each case instead of
>> just
>> +         * once at the end in case an operation like the branch
>> +         * operation needs to change the index.
>> +         */
>> +        case SEQ_OP_STOP:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            /* A stop operation in any position stops the sequencer
>> */
>> +            trace_pnv_spi_sequencer_op("STOP", get_seq_index(s));
>> +
>> +            stop = true;
>> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_IDLE);
>> +            s->loop_counter_1 = 0;
>> +            s->loop_counter_2 = 0;
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_IDLE);
>> +            break;
>> +
>> +        case SEQ_OP_SELECT_SLAVE:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("SELECT_SLAVE",
>> get_seq_index(s));
>> +            /*
>> +             * This device currently only supports a single
>> responder
>> +             * connection at position 0.  De-selecting a responder
>> is fine
>> +             * and expected at the end of a sequence but selecting
>> any
>> +             * responder other than 0 should cause an error.
>> +             */
> Use macro to extract opcode sequence below.
>
>> +            s->responder_select = opcode & 0x0F;
>> +            if (s->responder_select == 0) {
>> +                trace_pnv_spi_shifter_done();
>> +                qemu_set_irq(s->cs_line[0], 1);
>> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
>> +                                (get_seq_index(s) + 1));
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_DONE);
>> +            } else if (s->responder_select != 1) {
>> +                qemu_log_mask(LOG_GUEST_ERROR, "Slave selection
>> other than 1 "
>> +                              "not supported, select = 0x%x\n",
>> +                               s->responder_select);
>> +                trace_pnv_spi_sequencer_stop_requested("invalid "
>> +                                "responder select");
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_IDLE);
>> +                stop = true;
>> +            } else {
>> +                /*
>> +                 * Only allow an FSM_START state when a responder is
>> +                 * selected
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_START);
>> +                trace_pnv_spi_shifter_stating();
>> +                qemu_set_irq(s->cs_line[0], 0);
>> +                /*
>> +                 * A Shift_N2 operation is only valid after a
>> Shift_N1
>> +                 * according to the spec. The spec doesn't say if
>> that means
>> +                 * immediately after or just after at any point. We
>> will track
>> +                 * the occurrence of a Shift_N1 to enforce this
>> requirement in
>> +                 * the most generic way possible by assuming that
>> the rule
>> +                 * applies once a valid responder select has
>> occurred.
>> +                 */
>> +                s->shift_n1_done = false;
>> +                next_sequencer_fsm(s);
>> +            }
>> +            break;
>> +
>> +        case SEQ_OP_SHIFT_N1:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("SHIFT_N1",
>> get_seq_index(s));
>> +            /*
>> +             * Only allow a shift_n1 when the state is not IDLE or
>> DONE.
>> +             * In either of those two cases the sequencer is not in
>> a proper
>> +             * state to perform shift operations because the
>> sequencer has:
>> +             * - processed a responder deselect (DONE)
>> +             * - processed a stop opcode (IDLE)
>> +             * - encountered an error (IDLE)
>> +             */
>> +            if ((GETFIELD(SPI_STS_SHIFTER_FSM, s->status) ==
>> FSM_IDLE) ||
>> +                (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) ==
>> FSM_DONE)) {
>> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed
>> in "
>> +                              "shifter state = 0x%llx", GETFIELD(
>> +                        SPI_STS_SHIFTER_FSM, s->status));
>> +                /*
>> +                 * Set sequencer FSM error bit 3
>> (general_SPI_status[3])
>> +                 * in status reg.
>> +                 */
> Replace PPC_BIT(35) with defined name below
>
>> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
>> +                trace_pnv_spi_sequencer_stop_requested("invalid
>> shifter state");
>> +                stop = true;
>> +            } else {
>> +                /*
>> +                 * Look for the special case where there is a
>> shift_n1 set for
>> +                 * transmit and it is followed by a shift_n2 set for
>> transmit
>> +                 * AND the combined transmit length of the two
>> operations is
>> +                 * less than or equal to the size of the TDR
>> register. In this
>> +                 * case we want to use both this current shift_n1
>> opcode and the
>> +                 * following shift_n2 opcode to assemble the frame
>> for
>> +                 * transmission to the responder without requiring a
>> refill of
>> +                 * the TDR between the two operations.
>> +                 */
> Use a macro to extract the opcode sequence below.
>
>> +                if ((s->seq_op[get_seq_index(s) + 1] & 0xF0)
>> +                                == SEQ_OP_SHIFT_N2) {
>> +                    send_n1_alone = false;
>> +                }
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> +                                FSM_SHIFT_N1);
>> +                stop = operation_shiftn1(s, opcode, &payload,
>> send_n1_alone);
>> +                if (stop) {
>> +                    /*
>> +                     *  The operation code says to stop, this can
>> occur if:
>> +                     * (1) RDR is full and the N1 shift is set for
>> receive
>> +                     * (2) TDR was empty at the time of the N1 shift
>> so we need
>> +                     * to wait for data.
>> +                     * (3) Neither 1 nor 2 are occurring and we
>> aren't sending
>> +                     * N1 alone and N2 counter reload is set (bit 0
>> of the N2
>> +                     * counter reload field).  In this case
>> TDR_underrun will
>> +                     * will be set and the Payload has been loaded
>> so it is
>> +                     * ok to advance the sequencer.
>> +                     */
>> +                    if (GETFIELD(SPI_STS_TDR_UNDERRUN, s->status)) {
>> +                        s->shift_n1_done = true;
>> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
>>> status,
>> +                                                  FSM_SHIFT_N2);
>> +                        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s-
>>> status,
>> +                                        (get_seq_index(s) + 1));
>> +                    } else {
>> +                        /*
>> +                         * This is case (1) or (2) so the sequencer
>> needs to
>> +                         * wait and NOT go to the next sequence yet.
>> +                         */
>> +                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
>>> status,
>> +                                        FSM_WAIT);
>> +                    }
>> +                } else {
>> +                    /* Ok to move on to the next index */
>> +                    s->shift_n1_done = true;
>> +                    next_sequencer_fsm(s);
>> +                }
>> +            }
>> +            break;
>> +
>> +        case SEQ_OP_SHIFT_N2:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("SHIFT_N2",
>> get_seq_index(s));
>> +            if (!s->shift_n1_done) {
>> +                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not
>> allowed if a "
>> +                              "Shift_N1 is not done, shifter state =
>> 0x%llx",
>> +                              GETFIELD(SPI_STS_SHIFTER_FSM, s-
>>> status));
>> +                /*
>> +                 * In case the sequencer actually stops if an N2
>> shift is
>> +                 * requested before any N1 shift is done. Set
>> sequencer FSM
>> +                 * error bit 3 (general_SPI_status[3]) in status
>> reg.
>> +                 */
>> +                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
>> +                trace_pnv_spi_sequencer_stop_requested("shift_n2 "
>> +                                    "w/no shift_n1 done");
>> +                stop = true;
>> +            } else {
>> +                /* Ok to do a Shift_N2 */
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> +                                FSM_SHIFT_N2);
>> +                stop = operation_shiftn2(s, opcode, &payload);
>> +                /*
>> +                 * If the operation code says to stop set the
>> shifter state to
>> +                 * wait and stop
>> +                 */
>> +                if (stop) {
>> +                    s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s-
>>> status,
>> +                                    FSM_WAIT);
>> +                } else {
>> +                    /* Ok to move on to the next index */
>> +                    next_sequencer_fsm(s);
>> +                }
>> +            }
>> +            break;
>> +
>> +        case SEQ_OP_BRANCH_IFNEQ_RDR:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_RDR",
>> get_seq_index(s));
>> +            /*
>> +             * The memory mapping register RDR match value is
>> compared against
>> +             * the 16 rightmost bytes of the RDR (potentially with
>> masking).
>> +             * Since this comparison is performed against the
>> contents of the
>> +             * RDR then a receive must have previously occurred
>> otherwise
>> +             * there is no data to compare and the operation cannot
>> be
>> +             * completed and will stop the sequencer until RDR full
>> is set to
>> +             * 1.
>> +             */
>> +            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
>> +                bool rdr_matched = false;
>> +                rdr_matched = does_rdr_match(s);
>> +                if (rdr_matched) {
>> +                    trace_pnv_spi_RDR_match("success");
>> +                    /* A match occurred, increment the sequencer
>> index. */
>> +                    next_sequencer_fsm(s);
>> +                } else {
>> +                    trace_pnv_spi_RDR_match("failed");
>> +                    /*
>> +                     * Branch the sequencer to the index coded into
>> the op
>> +                     * code.
>> +                     */
>> +                    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s-
>>> status,
> Use macro to extract opcode variable below.
>
>> +                                    (opcode & 0x7));
>> +                }
>> +                /*
>> +                 * Regardless of where the branch ended up we want
>> the
>> +                 * sequencer to continue shifting so we have to
>> clear
>> +                 * RDR_full.
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status,
>> 0);
>> +            } else {
>> +                trace_pnv_spi_sequencer_stop_requested("RDR not"
>> +                                "full for 0x6x opcode");
>> +                stop = true;
>> +                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_WAIT);
>> +            }
>> +            break;
>> +
>> +        case SEQ_OP_TRANSFER_TDR:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not
>> supported\n");
>> +            next_sequencer_fsm(s);
>> +            break;
>> +
>> +        case SEQ_OP_BRANCH_IFNEQ_INC_1:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_1",
>> get_seq_index(s));
>> +            /*
>> +             * The spec says the loop should execute count compare +
>> 1 times.
>> +             * However we learned from engineering that we really
>> only loop
>> +             * count_compare times, count compare = 0 makes this op
>> code a
>> +             * no-op
>> +             */
>> +            if (s->loop_counter_1 !=
>> +                GETFIELD(SPI_CTR_CFG_CMP1, s-
>>> regs[SPI_CTR_CFG_REG])) {
>> +                /*
>> +                 * Next index is the lower nibble of the branch
>> operation ID,
>> +                 * mask off all but the first three bits so we don't
>> try to
>> +                 * access beyond the sequencer_operation_reg
>> boundary.
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> Use macro to extract opcode variable below.
>
>> +                                (opcode & 0x7));
>> +                s->loop_counter_1++;
>> +            } else {
>> +                /* Continue to next index if loop counter is reached
>> */
>> +                next_sequencer_fsm(s);
>> +            }
>> +            break;
>> +
>> +        case SEQ_OP_BRANCH_IFNEQ_INC_2:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_2",
>> get_seq_index(s));
>> +            uint8_t condition2 = GETFIELD(SPI_CTR_CFG_CMP2,
>> +                              s->regs[SPI_CTR_CFG_REG]);
>> +            /*
>> +             * The spec says the loop should execute count compare +
>> 1 times.
>> +             * However we learned from engineering that we really
>> only loop
>> +             * count_compare times, count compare = 0 makes this op
>> code a
>> +             * no-op
>> +             */
>> +            if (s->loop_counter_2 != condition2) {
>> +                /*
>> +                 * Next index is the lower nibble of the branch
>> operation ID,
>> +                 * mask off all but the first three bits so we don't
>> try to
>> +                 * access beyond the sequencer_operation_reg
>> boundary.
>> +                 */
>> +                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
> Use macro to get opcode variable below
>
>> +                                          (opcode & 0x7));
>> +                s->loop_counter_2++;
>> +            } else {
>> +                /* Continue to next index if loop counter is reached
>> */
>> +                next_sequencer_fsm(s);
>> +            }
>> +            break;
>> +
>> +        default:
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_EXECUTE);
>> +            /* Ignore unsupported operations. */
>> +            next_sequencer_fsm(s);
>> +            break;
>> +        } /* end of switch */
>> +        /*
>> +         * If we used all 8 opcodes without seeing a 00 - STOP in
>> the sequence
>> +         * we need to go ahead and end things as if there was a STOP
>> at the
>> +         * end.
> Use a defined name instead of `8` below.
>
>> +        if (get_seq_index(s) == 8) {
>> +            /* All 8 opcodes completed, sequencer idling */
>> +            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
>> FSM_IDLE);
>> +            s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
>> +            s->loop_counter_1 = 0;
>> +            s->loop_counter_2 = 0;
>> +            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status,
>> SEQ_STATE_IDLE);
>> +            break;
>> +        }
>> +        /* Break the loop if a stop was requested */
>> +        if (stop) {
>> +            break;
>> +        }
>> +    } /* end of while */
>> +    return;
>> +} /* end of operation_sequencer() */
>> +
>> +/*
>> + * The SPIC engine and its internal sequencer can be interrupted and
>> reset by
>> + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive
>> + * Miscellaneous Register of sbe_register_bo device.
>> + * Reset immediately aborts any SPI transaction in progress and
>> returns the
>> + * sequencer and state machines to idle state.
>> + * The configuration register values are not changed. The status
>> register is
>> + * not reset. The engine registers are not reset.
>> + * The SPIC engine reset does not have any affect on the attached
>> devices.
>> + * Reset handling of any attached devices is beyond the scope of the
>> engine.
>> + */
>> +static void do_reset(DeviceState *dev)
>> +{
>> +    PnvSpi *s = PNV_SPI(dev);
>> +
>> +    trace_pnv_spi_reset();
>> +
>> +    /* Reset all N1 and N2 counters, and other constants */
>> +    s->N2_bits = 0;
>> +    s->N2_bytes = 0;
>> +    s->N2_tx = 0;
>> +    s->N2_rx = 0;
>> +    s->N1_bits = 0;
>> +    s->N1_bytes = 0;
>> +    s->N1_tx = 0;
>> +    s->N1_rx = 0;
>> +    s->loop_counter_1 = 0;
>> +    s->loop_counter_2 = 0;
>> +    /* Disconnected from responder */
>> +    qemu_set_irq(s->cs_line[0], 1);
>> +}
>> +
>>   static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr,
>> unsigned size)
>>   {
>>       PnvSpi *s = PNV_SPI(opaque);
>> @@ -36,6 +1067,10 @@ static uint64_t pnv_spi_xscom_read(void *opaque,
>> hwaddr addr, unsigned size)
>>           val = s->regs[reg];
>>           trace_pnv_spi_read_RDR(val);
>>           s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
>> +        if (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_WAIT) {
>> +            trace_pnv_spi_start_sequencer();
>> +            operation_sequencer(s);
>> +        }
>>           break;
>>       case SPI_SEQ_OP_REG:
>>           val = 0;
>> @@ -97,6 +1132,8 @@ static void pnv_spi_xscom_write(void *opaque,
>> hwaddr addr,
>>           trace_pnv_spi_write_TDR(val);
>>           s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 1);
>>           s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 0);
>> +        trace_pnv_spi_start_sequencer();
>> +        operation_sequencer(s);
>>           break;
>>       case SPI_SEQ_OP_REG:
>>           for (int i = 0; i < PNV_SPI_REG_SIZE; i++) {
>> @@ -129,6 +1166,7 @@ static const MemoryRegionOps pnv_spi_xscom_ops =
>> {
>>   
>>   static Property pnv_spi_properties[] = {
>>       DEFINE_PROP_UINT32("spic_num", PnvSpi, spic_num, 0),
>> +    DEFINE_PROP_UINT8("transfer_len", PnvSpi, transfer_len, 4),
>>       DEFINE_PROP_END_OF_LIST(),
>>   };
>>   
>> @@ -180,6 +1218,7 @@ static void pnv_spi_class_init(ObjectClass
>> *klass, void *data)
>>   
>>       dc->desc = "PowerNV SPI";
>>       dc->realize = pnv_spi_realize;
>> +    dc->reset = do_reset;
>>       device_class_set_props(dc, pnv_spi_properties);
>>   }
>>   
>> diff --git a/hw/ssi/trace-events b/hw/ssi/trace-events
>> index 4388024a05..7fa27ebade 100644
>> --- a/hw/ssi/trace-events
>> +++ b/hw/ssi/trace-events
>> @@ -38,3 +38,18 @@ pnv_spi_read(uint64_t addr, uint64_t val) "addr
>> 0x%" PRIx64 " val 0x%" PRIx64
>>   pnv_spi_write(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val
>> 0x%" PRIx64
>>   pnv_spi_read_RDR(uint64_t val) "data extracted = 0x%" PRIx64
>>   pnv_spi_write_TDR(uint64_t val) "being written, data written = 0x%"
>> PRIx64
>> +pnv_spi_start_sequencer(void) ""
>> +pnv_spi_reset(void) "spic engine sequencer configuration and spi
>> communication"
>> +pnv_spi_sequencer_op(const char* op, uint8_t index) "%s at index =
>> 0x%x"
>> +pnv_spi_shifter_stating(void) "pull CS line low"
>> +pnv_spi_shifter_done(void) "pull the CS line high"
>> +pnv_spi_log_Ncounts(uint8_t N1_bits, uint8_t N1_bytes, uint8_t
>> N1_tx, uint8_t N1_rx, uint8_t N2_bits, uint8_t N2_bytes, uint8_t
>> N2_tx, uint8_t N2_rx) "N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx
>> = %d, N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d"
>> +pnv_spi_tx_append(const char* frame, uint8_t byte, uint8_t
>> tdr_index) "%s = 0x%2.2x to payload from TDR at index %d"
>> +pnv_spi_tx_append_FF(const char* frame) "%s to Payload"
>> +pnv_spi_tx_request(const char* frame, uint32_t payload_len) "%s,
>> payload len = %d"
>> +pnv_spi_rx_received(uint32_t payload_len) "payload len = %d"
>> +pnv_spi_rx_read_N1frame(void) ""
>> +pnv_spi_rx_read_N2frame(void) ""
>> +pnv_spi_shift_rx(uint8_t byte, uint32_t index) "byte = 0x%2.2x into
>> RDR from payload index %d"
>> +pnv_spi_sequencer_stop_requested(const char* reason) "due to %s"
>> +pnv_spi_RDR_match(const char* result) "%s"
diff mbox series

Patch

diff --git a/include/hw/ssi/pnv_spi.h b/include/hw/ssi/pnv_spi.h
index 71c53d4a17..21fbfcb69c 100644
--- a/include/hw/ssi/pnv_spi.h
+++ b/include/hw/ssi/pnv_spi.h
@@ -8,6 +8,14 @@ 
  * This model Supports a connection to a single SPI responder.
  * Introduced for P10 to provide access to SPI seeproms, TPM, flash device
  * and an ADC controller.
+ *
+ * All SPI function control is mapped into the SPI register space to enable
+ * full control by firmware.
+ *
+ * SPI Controller has sequencer and shift engine. The SPI shift engine
+ * performs serialization and de-serialization according to the control by
+ * the sequencer and according to the setup defined in the configuration
+ * registers and the SPI sequencer implements the main control logic.
  */
 #include "hw/ssi/ssi.h"
 #include "hw/sysbus.h"
@@ -50,6 +58,25 @@  typedef struct PnvSpi {
     MemoryRegion    xscom_spic_regs;
     /* SPI object number */
     uint32_t        spic_num;
+    uint8_t         transfer_len;
+    uint8_t         responder_select;
+    /* To verify if shift_n1 happens prior to shift_n2 */
+    bool            shift_n1_done;
+    /* Loop counter for branch operation opcode Ex/Fx */
+    uint8_t         loop_counter_1;
+    uint8_t         loop_counter_2;
+    /* N1/N2_bits specifies the size of the N1/N2 segment of a frame in bits.*/
+    uint8_t         N1_bits;
+    uint8_t         N2_bits;
+    /* Number of bytes in a payload for the N1/N2 frame segment.*/
+    uint8_t         N1_bytes;
+    uint8_t         N2_bytes;
+    /* Number of N1/N2 bytes marked for transmit */
+    uint8_t         N1_tx;
+    uint8_t         N2_tx;
+    /* Number of N1/N2 bytes marked for receive */
+    uint8_t         N1_rx;
+    uint8_t         N2_rx;
 
     /* SPI registers */
     uint64_t        regs[PNV_SPI_REGS];
diff --git a/hw/ssi/pnv_spi.c b/hw/ssi/pnv_spi.c
index da9e3925dd..b8f4370525 100644
--- a/hw/ssi/pnv_spi.c
+++ b/hw/ssi/pnv_spi.c
@@ -14,9 +14,1040 @@ 
 #include "hw/ssi/pnv_spi_regs.h"
 #include "hw/ssi/ssi.h"
 #include <libfdt.h>
+#include <math.h>
 #include "hw/irq.h"
 #include "trace.h"
 
+/* PnvXferBuffer */
+typedef struct PnvXferBuffer {
+
+    uint32_t    len;
+    uint8_t    *data;
+
+} PnvXferBuffer;
+
+/* pnv_spi_xfer_buffer_methods */
+static PnvXferBuffer *pnv_spi_xfer_buffer_new(void)
+{
+    PnvXferBuffer *payload = g_malloc0(sizeof(*payload));
+
+    return payload;
+}
+
+static void pnv_spi_xfer_buffer_free(PnvXferBuffer *payload)
+{
+    free(payload->data);
+    free(payload);
+}
+
+static uint8_t *pnv_spi_xfer_buffer_write_ptr(PnvXferBuffer *payload,
+                uint32_t offset, uint32_t length)
+{
+    if (payload->len < (offset + length)) {
+        payload->len = offset + length;
+        payload->data = g_realloc(payload->data, payload->len);
+    }
+    return &payload->data[offset];
+}
+
+static bool does_rdr_match(PnvSpi *s)
+{
+    /*
+     * According to spec, the mask bits that are 0 are compared and the
+     * bits that are 1 are ignored.
+     */
+    uint16_t rdr_match_mask = GETFIELD(SPI_MM_RDR_MATCH_MASK,
+                                        s->regs[SPI_MM_REG]);
+    uint16_t rdr_match_val = GETFIELD(SPI_MM_RDR_MATCH_VAL,
+                                        s->regs[SPI_MM_REG]);
+
+    if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) &
+            GETFIELD(PPC_BITMASK(48, 63), s->regs[SPI_RCV_DATA_REG]))) {
+        return true;
+    }
+    return false;
+}
+
+static uint8_t get_from_offset(PnvSpi *s, uint8_t offset)
+{
+    uint8_t byte;
+
+    /*
+     * Offset is an index between 0 and PNV_SPI_REG_SIZE - 1
+     * Check the offset before using it.
+     */
+    if (offset < PNV_SPI_REG_SIZE) {
+        byte = (s->regs[SPI_XMIT_DATA_REG] >> (56 - offset * 8)) & 0xFF;
+    } else {
+        /*
+         * Log an error and return a 0xFF since we have to assign something
+         * to byte before returning.
+         */
+        qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to get byte "
+                      "from TDR\n", offset);
+        byte = 0xff;
+    }
+    return byte;
+}
+
+static uint8_t read_from_frame(PnvSpi *s, uint8_t *read_buf, uint8_t nr_bytes,
+                uint8_t ecc_count, uint8_t shift_in_count)
+{
+    uint8_t byte;
+    int count = 0;
+
+    while (count < nr_bytes) {
+        shift_in_count++;
+        if ((ecc_count != 0) &&
+            (shift_in_count == (PNV_SPI_REG_SIZE + ecc_count))) {
+            shift_in_count = 0;
+        } else {
+            byte = read_buf[count];
+            trace_pnv_spi_shift_rx(byte, count);
+            s->regs[SPI_RCV_DATA_REG] = (s->regs[SPI_RCV_DATA_REG] << 8) | byte;
+        }
+        count++;
+    } /* end of while */
+    return shift_in_count;
+}
+
+static void spi_response(PnvSpi *s, int bits, PnvXferBuffer *rsp_payload)
+{
+    uint8_t ecc_count;
+    uint8_t shift_in_count;
+
+    /*
+     * Processing here must handle:
+     * - Which bytes in the payload we should move to the RDR
+     * - Explicit mode counter configuration settings
+     * - RDR full and RDR overrun status
+     */
+
+    /*
+     * First check that the response payload is the exact same
+     * number of bytes as the request payload was
+     */
+    if (rsp_payload->len != (s->N1_bytes + s->N2_bytes)) {
+        qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload size in "
+                       "bytes, expected %d, got %d\n",
+                       (s->N1_bytes + s->N2_bytes), rsp_payload->len);
+    } else {
+        uint8_t ecc_control;
+        trace_pnv_spi_rx_received(rsp_payload->len);
+        trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
+                        s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
+        /*
+         * Adding an ECC count let's us know when we have found a payload byte
+         * that was shifted in but cannot be loaded into RDR.  Bits 29-30 of
+         * clock_config_reset_control register equal to either 0b00 or 0b10
+         * indicate that we are taking in data with ECC and either applying
+         * the ECC or discarding it.
+         */
+        ecc_count = 0;
+        ecc_control = GETFIELD(PPC_BITMASK(29, 30), s->regs[SPI_CLK_CFG_REG]);
+        if (ecc_control == 0 || ecc_control == 2) {
+            ecc_count = 1;
+        }
+        /*
+         * Use the N1_rx and N2_rx counts to control shifting data from the
+         * payload into the RDR.  Keep an overall count of the number of bytes
+         * shifted into RDR so we can discard every 9th byte when ECC is
+         * enabled.
+         */
+        shift_in_count = 0;
+        /* Handle the N1 portion of the frame first */
+        if (s->N1_rx != 0) {
+            trace_pnv_spi_rx_read_N1frame();
+            shift_in_count = read_from_frame(s, &rsp_payload->data[0],
+                            s->N1_bytes, ecc_count, shift_in_count);
+        }
+        /* Handle the N2 portion of the frame */
+        if (s->N2_rx != 0) {
+            trace_pnv_spi_rx_read_N2frame();
+            shift_in_count = read_from_frame(s,
+                            &rsp_payload->data[s->N1_bytes], s->N2_bytes,
+                            ecc_count, shift_in_count);
+        }
+        if ((s->N1_rx + s->N2_rx) > 0) {
+            /*
+             * Data was received so handle RDR status.
+             * It is easier to handle RDR_full and RDR_overrun status here
+             * since the RDR register's shift_byte_in method is called
+             * multiple times in a row. Controlling RDR status is done here
+             * instead of in the RDR scoped methods for that reason.
+             */
+            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
+                /*
+                 * Data was shifted into the RDR before having been read
+                 * causing previous data to have been overrun.
+                 */
+                s->status = SETFIELD(SPI_STS_RDR_OVERRUN, s->status, 1);
+            } else {
+                /*
+                 * Set status to indicate that the received data register is
+                 * full. This flag is only cleared once the RDR is unloaded.
+                 */
+                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 1);
+            }
+        }
+    } /* end of else */
+} /* end of spi_response() */
+
+static void transfer(PnvSpi *s, PnvXferBuffer *payload)
+{
+    uint32_t tx;
+    uint32_t rx;
+    PnvXferBuffer *rsp_payload = NULL;
+
+    rsp_payload = pnv_spi_xfer_buffer_new();
+    for (int offset = 0; offset < payload->len; offset += s->transfer_len) {
+        tx = 0;
+        for (int i = 0; i < s->transfer_len; i++) {
+            if ((offset + i) >= payload->len) {
+                tx <<= 8;
+            } else {
+                tx = (tx << 8) | payload->data[offset + i];
+            }
+        }
+        rx = ssi_transfer(s->ssi_bus, tx);
+        for (int i = 0; i < s->transfer_len; i++) {
+            if ((offset + i) >= payload->len) {
+                break;
+            }
+            *(pnv_spi_xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) =
+                    (rx >> (8 * (s->transfer_len - 1) - i * 8)) & 0xFF;
+        }
+    }
+    if (rsp_payload != NULL) {
+        spi_response(s, s->N1_bits, rsp_payload);
+    }
+}
+
+static inline uint8_t get_seq_index(PnvSpi *s)
+{
+    return GETFIELD(SPI_STS_SEQ_INDEX, s->status);
+}
+
+static inline void next_sequencer_fsm(PnvSpi *s)
+{
+    uint8_t seq_index = get_seq_index(s);
+    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, (seq_index + 1));
+    s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_INDEX_INCREMENT);
+}
+
+/*
+ * Calculate the N1 counters based on passed in opcode and
+ * internal register values.
+ * The method assumes that the opcode is a Shift_N1 opcode
+ * and doesn't test it.
+ * The counters returned are:
+ * N1 bits: Number of bits in the payload data that are significant
+ * to the responder.
+ * N1_bytes: Total count of payload bytes for the N1 (portion of the) frame.
+ * N1_tx: Total number of bytes taken from TDR for N1
+ * N1_rx: Total number of bytes taken from the payload for N1
+ */
+static void calculate_N1(PnvSpi *s, uint8_t opcode)
+{
+    /*
+     * Shift_N1 opcode form: 0x3M
+     * Implicit mode:
+     * If M != 0 the shift count is M bytes and M is the number of tx bytes.
+     * Forced Implicit mode:
+     * M is the shift count but tx and rx is determined by the count control
+     * register fields.  Note that we only check for forced Implicit mode when
+     * M != 0 since the mode doesn't make sense when M = 0.
+     * Explicit mode:
+     * If M == 0 then shift count is number of bits defined in the
+     * Counter Configuration Register's shift_count_N1 field.
+     */
+    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
+        /* Explicit mode */
+        s->N1_bits = GETFIELD(SPI_CTR_CFG_N1, s->regs[SPI_CTR_CFG_REG]);
+        s->N1_bytes = ceil(s->N1_bits / 8);
+        s->N1_tx = 0;
+        s->N1_rx = 0;
+        /* If tx count control for N1 is set, load the tx value */
+        if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            s->N1_tx = s->N1_bytes;
+        }
+        /* If rx count control for N1 is set, load the rx value */
+        if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            s->N1_rx = s->N1_bytes;
+        }
+    } else {
+        /* Implicit mode/Forced Implicit mode, use M field from opcode */
+        s->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
+        s->N1_bits = s->N1_bytes * 8;
+        /*
+         * Assume that we are going to transmit the count
+         * (pure Implicit only)
+         */
+        s->N1_tx = s->N1_bytes;
+        s->N1_rx = 0;
+        /* Let Forced Implicit mode have an effect on the counts */
+        if (GETFIELD(PPC_BIT(49), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            /*
+             * If Forced Implicit mode and count control doesn't
+             * indicate transmit then reset the tx count to 0
+             */
+            if (GETFIELD(PPC_BIT(50), s->regs[SPI_CTR_CFG_REG]) == 0) {
+                s->N1_tx = 0;
+            }
+            /* If rx count control for N1 is set, load the rx value */
+            if (GETFIELD(PPC_BIT(51), s->regs[SPI_CTR_CFG_REG]) == 1) {
+                s->N1_rx = s->N1_bytes;
+            }
+        }
+    }
+    /*
+     * Enforce an upper limit on the size of N1 that is equal to the known size
+     * of the shift register, 64 bits or 72 bits if ECC is enabled.
+     * If the size exceeds 72 bits it is a user error so log an error,
+     * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM
+     * error bit.
+     */
+    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
+                                   s->regs[SPI_CLK_CFG_REG]);
+    if (ecc_control == 0 || ecc_control == 2) {
+        if (s->N1_bytes > (PNV_SPI_REG_SIZE + 1)) {
+            qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size when "
+                          "ECC enabled, bytes = 0x%x, bits = 0x%x\n",
+                          s->N1_bytes, s->N1_bits);
+            s->N1_bytes = PNV_SPI_REG_SIZE + 1;
+            s->N1_bits = s->N1_bytes * 8;
+        }
+    } else if (s->N1_bytes > PNV_SPI_REG_SIZE) {
+        qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, "
+                      "bytes = 0x%x, bits = 0x%x\n",
+                      s->N1_bytes, s->N1_bits);
+        s->N1_bytes = PNV_SPI_REG_SIZE;
+        s->N1_bits = s->N1_bytes * 8;
+    }
+} /* end of calculate_N1 */
+
+/*
+ * Shift_N1 operation handler method
+ */
+static bool operation_shiftn1(PnvSpi *s, uint8_t opcode,
+                       PnvXferBuffer **payload, bool send_n1_alone)
+{
+    uint8_t n1_count;
+    bool stop = false;
+
+    /*
+     * If there isn't a current payload left over from a stopped sequence
+     * create a new one.
+     */
+    if (*payload == NULL) {
+        *payload = pnv_spi_xfer_buffer_new();
+    }
+    /*
+     * Use a combination of N1 counters to build the N1 portion of the
+     * transmit payload.
+     * We only care about transmit at this time since the request payload
+     * only represents data going out on the controller output line.
+     * Leave mode specific considerations in the calculate function since
+     * all we really care about are counters that tell use exactly how
+     * many bytes are in the payload and how many of those bytes to
+     * include from the TDR into the payload.
+     */
+    calculate_N1(s, opcode);
+    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
+                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
+    /*
+     * Zero out the N2 counters here in case there is no N2 operation following
+     * the N1 operation in the sequencer.  This keeps leftover N2 information
+     * from interfering with spi_response logic.
+     */
+    s->N2_bits = 0;
+    s->N2_bytes = 0;
+    s->N2_tx = 0;
+    s->N2_rx = 0;
+    /*
+     * N1_bytes is the overall size of the N1 portion of the frame regardless of
+     * whether N1 is used for tx, rx or both.  Loop over the size to build a
+     * payload that is N1_bytes long.
+     * N1_tx is the count of bytes to take from the TDR and "shift" into the
+     * frame which means append those bytes to the payload for the N1 portion
+     * of the frame.
+     * If N1_tx is 0 or if the count exceeds the size of the TDR append 0xFF to
+     * the frame until the overall N1 count is reached.
+     */
+    n1_count = 0;
+    while (n1_count < s->N1_bytes) {
+        /*
+         * Assuming that if N1_tx is not equal to 0 then it is the same as
+         * N1_bytes.
+         */
+        if ((s->N1_tx != 0) && (n1_count < PNV_SPI_REG_SIZE)) {
+
+            if (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1) {
+                /*
+                 * Note that we are only appending to the payload IF the TDR
+                 * is full otherwise we don't touch the payload because we are
+                 * going to NOT send the payload and instead tell the sequencer
+                 * that called us to stop and wait for a TDR write so we have
+                 * data to load into the payload.
+                 */
+                uint8_t n1_byte = 0x00;
+                n1_byte = get_from_offset(s, n1_count);
+                trace_pnv_spi_tx_append("n1_byte", n1_byte, n1_count);
+                *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) =
+                        n1_byte;
+            } else {
+                /*
+                 * We hit a shift_n1 opcode TX but the TDR is empty, tell the
+                 * sequencer to stop and break this loop.
+                 */
+                trace_pnv_spi_sequencer_stop_requested("Shift N1"
+                                "set for transmit but TDR is empty");
+                stop = true;
+                break;
+            }
+        } else {
+            /*
+             * Cases here:
+             * - we are receiving during the N1 frame segment and the RDR
+             *   is full so we need to stop until the RDR is read
+             * - we are transmitting and we don't care about RDR status
+             *   since we won't be loading RDR during the frame segment.
+             * - we are receiving and the RDR is empty so we allow the operation
+             *   to proceed.
+             */
+            if ((s->N1_rx != 0) && (GETFIELD(SPI_STS_RDR_FULL,
+                                           s->status) == 1)) {
+                trace_pnv_spi_sequencer_stop_requested("shift N1"
+                                "set for receive but RDR is full");
+                stop = true;
+                break;
+            } else {
+                trace_pnv_spi_tx_append_FF("n1_byte");
+                *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
+                        = 0xff;
+            }
+        }
+        n1_count++;
+    } /* end of while */
+    /*
+     * If we are not stopping due to an empty TDR and we are doing an N1 TX
+     * and the TDR is full we need to clear the TDR_full status.
+     * Do this here instead of up in the loop above so we don't log the message
+     * in every loop iteration.
+     * Ignore the send_n1_alone flag, all that does is defer the TX until the N2
+     * operation, which was found immediately after the current opcode.  The TDR
+     * was unloaded and will be shifted so we have to clear the TDR_full status.
+     */
+    if (!stop && (s->N1_tx != 0) &&
+        (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
+        s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
+    }
+    /*
+     * There are other reasons why the shifter would stop, such as a TDR empty
+     * or RDR full condition with N1 set to receive.  If we haven't stopped due
+     * to either one of those conditions then check if the send_n1_alone flag is
+     * equal to False, indicating the next opcode is an N2 operation, AND if
+     * the N2 counter reload switch (bit 0 of the N2 count control field) is
+     * set.  This condition requires a pacing write to "kick" off the N2
+     * shift which includes the N1 shift as well when send_n1_alone is False.
+     */
+    if (!stop && !send_n1_alone &&
+       (GETFIELD(PPC_BIT(52), s->regs[SPI_CTR_CFG_REG]) == 1)) {
+        trace_pnv_spi_sequencer_stop_requested("N2 counter reload "
+                        "active, stop N1 shift, TDR_underrun set to 1");
+        stop = true;
+        s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 1);
+    }
+    /*
+     * If send_n1_alone is set AND we have a full TDR then this is the first and
+     * last payload to send and we don't have an N2 frame segment to add to the
+     * payload.
+     */
+    if (send_n1_alone && !stop) {
+        /* We have a TX and a full TDR or an RX and an empty RDR */
+        trace_pnv_spi_tx_request("Shifting N1 frame", (*payload)->len);
+        transfer(s, *payload);
+        /* The N1 frame shift is complete so reset the N1 counters */
+        s->N2_bits = 0;
+        s->N2_bytes = 0;
+        s->N2_tx = 0;
+        s->N2_rx = 0;
+        pnv_spi_xfer_buffer_free(*payload);
+        *payload = NULL;
+    }
+    return stop;
+} /* end of operation_shiftn1() */
+
+/*
+ * Calculate the N2 counters based on passed in opcode and
+ * internal register values.
+ * The method assumes that the opcode is a Shift_N2 opcode
+ * and doesn't test it.
+ * The counters returned are:
+ * N2 bits: Number of bits in the payload data that are significant
+ * to the responder.
+ * N2_bytes: Total count of payload bytes for the N2 frame.
+ * N2_tx: Total number of bytes taken from TDR for N2
+ * N2_rx: Total number of bytes taken from the payload for N2
+ */
+static void calculate_N2(PnvSpi *s, uint8_t opcode)
+{
+    /*
+     * Shift_N2 opcode form: 0x4M
+     * Implicit mode:
+     * If M!=0 the shift count is M bytes and M is the number of rx bytes.
+     * Forced Implicit mode:
+     * M is the shift count but tx and rx is determined by the count control
+     * register fields.  Note that we only check for Forced Implicit mode when
+     * M != 0 since the mode doesn't make sense when M = 0.
+     * Explicit mode:
+     * If M==0 then shift count is number of bits defined in the
+     * Counter Configuration Register's shift_count_N1 field.
+     */
+    if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) {
+        /* Explicit mode */
+        s->N2_bits = GETFIELD(SPI_CTR_CFG_N2, s->regs[SPI_CTR_CFG_REG]);
+        s->N2_bytes = ceil(s->N2_bits / 8);
+        s->N2_tx = 0;
+        s->N2_rx = 0;
+        /* If tx count control for N2 is set, load the tx value */
+        if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            s->N2_tx = s->N2_bytes;
+        }
+        /* If rx count control for N2 is set, load the rx value */
+        if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            s->N2_rx = s->N2_bytes;
+        }
+    } else {
+        /* Implicit mode/Forced Implicit mode, use M field from opcode */
+        s->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode);
+        s->N2_bits = s->N2_bytes * 8;
+        /* Assume that we are going to receive the count */
+        s->N2_rx = s->N2_bytes;
+        s->N2_tx = 0;
+        /* Let Forced Implicit mode have an effect on the counts */
+        if (GETFIELD(PPC_BIT(53), s->regs[SPI_CTR_CFG_REG]) == 1) {
+            /*
+             * If Forced Implicit mode and count control doesn't
+             * indicate a receive then reset the rx count to 0
+             */
+            if (GETFIELD(PPC_BIT(55), s->regs[SPI_CTR_CFG_REG]) == 0) {
+                s->N2_rx = 0;
+            }
+            /* If tx count control for N2 is set, load the tx value */
+            if (GETFIELD(PPC_BIT(54), s->regs[SPI_CTR_CFG_REG]) == 1) {
+                s->N2_tx = s->N2_bytes;
+            }
+        }
+    }
+    /*
+     * Enforce an upper limit on the size of N1 that is equal to the
+     * known size of the shift register, 64 bits or 72 bits if ECC
+     * is enabled.
+     * If the size exceeds 72 bits it is a user error so log an error,
+     * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM
+     * error bit.
+     */
+    uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30),
+                                   s->regs[SPI_CLK_CFG_REG]);
+    if (ecc_control == 0 || ecc_control == 2) {
+        if (s->N2_bytes > (PNV_SPI_REG_SIZE + 1)) {
+            /* Unsupported N2 shift size when ECC enabled */
+            s->N2_bytes = PNV_SPI_REG_SIZE + 1;
+            s->N2_bits = s->N2_bytes * 8;
+        }
+    } else if (s->N2_bytes > PNV_SPI_REG_SIZE) {
+        /* Unsupported N2 shift size */
+        s->N2_bytes = PNV_SPI_REG_SIZE;
+        s->N2_bits = s->N2_bytes * 8;
+    }
+} /* end of calculate_N2 */
+
+/*
+ * Shift_N2 operation handler method
+ */
+
+static bool operation_shiftn2(PnvSpi *s, uint8_t opcode,
+                       PnvXferBuffer **payload)
+{
+    uint8_t n2_count;
+    bool stop = false;
+
+    /*
+     * If there isn't a current payload left over from a stopped sequence
+     * create a new one.
+     */
+    if (*payload == NULL) {
+        *payload = pnv_spi_xfer_buffer_new();
+    }
+    /*
+     * Use a combination of N2 counters to build the N2 portion of the
+     * transmit payload.
+     */
+    calculate_N2(s, opcode);
+    trace_pnv_spi_log_Ncounts(s->N1_bits, s->N1_bytes, s->N1_tx,
+                    s->N1_rx, s->N2_bits, s->N2_bytes, s->N2_tx, s->N2_rx);
+    /*
+     * The only difference between this code and the code for shift N1 is
+     * that this code has to account for the possible presence of N1 transmit
+     * bytes already taken from the TDR.
+     * If there are bytes to be transmitted for the N2 portion of the frame
+     * and there are still bytes in TDR that have not been copied into the
+     * TX data of the payload, this code will handle transmitting those
+     * remaining bytes.
+     * If for some reason the transmit count(s) add up to more than the size
+     * of the TDR we will just append 0xFF to the transmit payload data until
+     * the payload is N1 + N2 bytes long.
+     */
+    n2_count = 0;
+    while (n2_count < s->N2_bytes) {
+        /*
+         * If the RDR is full and we need to RX just bail out, letting the
+         * code continue will end up building the payload twice in the same
+         * buffer since RDR full causes a sequence stop and restart.
+         */
+        if ((s->N2_rx != 0) &&
+            (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1)) {
+            trace_pnv_spi_sequencer_stop_requested("shift N2 set"
+                            "for receive but RDR is full");
+            stop = true;
+            break;
+        }
+        if ((s->N2_tx != 0) && ((s->N1_tx + n2_count) <
+                                PNV_SPI_REG_SIZE)) {
+            /* Always append data for the N2 segment if it is set for TX */
+            uint8_t n2_byte = 0x00;
+            n2_byte = get_from_offset(s, (s->N1_tx + n2_count));
+            trace_pnv_spi_tx_append("n2_byte", n2_byte, (s->N1_tx + n2_count));
+            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
+                    = n2_byte;
+        } else {
+            /*
+             * Regardless of whether or not N2 is set for TX or RX, we need
+             * the number of bytes in the payload to match the overall length
+             * of the operation.
+             */
+            trace_pnv_spi_tx_append_FF("n2_byte");
+            *(pnv_spi_xfer_buffer_write_ptr(*payload, (*payload)->len, 1))
+                    = 0xff;
+        }
+        n2_count++;
+    } /* end of while */
+    if (!stop) {
+        /* We have a TX and a full TDR or an RX and an empty RDR */
+        trace_pnv_spi_tx_request("Shifting N2 frame", (*payload)->len);
+        transfer(s, *payload);
+        /*
+         * If we are doing an N2 TX and the TDR is full we need to clear the
+         * TDR_full status. Do this here instead of up in the loop above so we
+         * don't log the message in every loop iteration.
+         */
+        if ((s->N2_tx != 0) &&
+            (GETFIELD(SPI_STS_TDR_FULL, s->status) == 1)) {
+            s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 0);
+        }
+        /*
+         * The N2 frame shift is complete so reset the N2 counters.
+         * Reset the N1 counters also in case the frame was a combination of
+         * N1 and N2 segments.
+         */
+        s->N2_bits = 0;
+        s->N2_bytes = 0;
+        s->N2_tx = 0;
+        s->N2_rx = 0;
+        s->N1_bits = 0;
+        s->N1_bytes = 0;
+        s->N1_tx = 0;
+        s->N1_rx = 0;
+        pnv_spi_xfer_buffer_free(*payload);
+        *payload = NULL;
+    }
+    return stop;
+} /*  end of operation_shiftn2()*/
+
+static void operation_sequencer(PnvSpi *s)
+{
+    /*
+     * Loop through each sequencer operation ID and perform the requested
+     *  operations.
+     * Flag for indicating if we should send the N1 frame or wait to combine
+     * it with a preceding N2 frame.
+     */
+    bool send_n1_alone = true;
+    bool stop = false; /* Flag to stop the sequencer */
+    uint8_t opcode = 0;
+    uint8_t masked_opcode = 0;
+
+    /*
+     * PnvXferBuffer for containing the payload of the SPI frame.
+     * This is a static because there are cases where a sequence has to stop
+     * and wait for the target application to unload the RDR.  If this occurs
+     * during a sequence where N1 is not sent alone and instead combined with
+     * N2 since the N1 tx length + the N2 tx length is less than the size of
+     * the TDR.
+     */
+    static PnvXferBuffer *payload;
+
+    if (payload == NULL) {
+        payload = pnv_spi_xfer_buffer_new();
+    }
+    /*
+     * Clear the sequencer FSM error bit - general_SPI_status[3]
+     * before starting a sequence.
+     */
+    s->status = SETFIELD(PPC_BIT(35), s->status, 0);
+    /*
+     * If the FSM is idle set the sequencer index to 0
+     * (new/restarted sequence)
+     */
+    if (GETFIELD(SPI_STS_SEQ_FSM, s->status) == SEQ_STATE_IDLE) {
+        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
+    }
+    /*
+     * There are only 8 possible operation IDs to iterate through though
+     * some operations may cause more than one frame to be sequenced.
+     */
+    while (get_seq_index(s) < 8) {
+        opcode = s->seq_op[get_seq_index(s)];
+        /* Set sequencer state to decode */
+        s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_DECODE);
+        /*
+         * Only the upper nibble of the operation ID is needed to know what
+         * kind of operation is requested.
+         */
+        masked_opcode = opcode & 0xF0;
+        switch (masked_opcode) {
+        /*
+         * Increment the operation index in each case instead of just
+         * once at the end in case an operation like the branch
+         * operation needs to change the index.
+         */
+        case SEQ_OP_STOP:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            /* A stop operation in any position stops the sequencer */
+            trace_pnv_spi_sequencer_op("STOP", get_seq_index(s));
+
+            stop = true;
+            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
+            s->loop_counter_1 = 0;
+            s->loop_counter_2 = 0;
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_IDLE);
+            break;
+
+        case SEQ_OP_SELECT_SLAVE:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("SELECT_SLAVE", get_seq_index(s));
+            /*
+             * This device currently only supports a single responder
+             * connection at position 0.  De-selecting a responder is fine
+             * and expected at the end of a sequence but selecting any
+             * responder other than 0 should cause an error.
+             */
+            s->responder_select = opcode & 0x0F;
+            if (s->responder_select == 0) {
+                trace_pnv_spi_shifter_done();
+                qemu_set_irq(s->cs_line[0], 1);
+                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
+                                (get_seq_index(s) + 1));
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_DONE);
+            } else if (s->responder_select != 1) {
+                qemu_log_mask(LOG_GUEST_ERROR, "Slave selection other than 1 "
+                              "not supported, select = 0x%x\n",
+                               s->responder_select);
+                trace_pnv_spi_sequencer_stop_requested("invalid "
+                                "responder select");
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
+                stop = true;
+            } else {
+                /*
+                 * Only allow an FSM_START state when a responder is
+                 * selected
+                 */
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_START);
+                trace_pnv_spi_shifter_stating();
+                qemu_set_irq(s->cs_line[0], 0);
+                /*
+                 * A Shift_N2 operation is only valid after a Shift_N1
+                 * according to the spec. The spec doesn't say if that means
+                 * immediately after or just after at any point. We will track
+                 * the occurrence of a Shift_N1 to enforce this requirement in
+                 * the most generic way possible by assuming that the rule
+                 * applies once a valid responder select has occurred.
+                 */
+                s->shift_n1_done = false;
+                next_sequencer_fsm(s);
+            }
+            break;
+
+        case SEQ_OP_SHIFT_N1:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("SHIFT_N1", get_seq_index(s));
+            /*
+             * Only allow a shift_n1 when the state is not IDLE or DONE.
+             * In either of those two cases the sequencer is not in a proper
+             * state to perform shift operations because the sequencer has:
+             * - processed a responder deselect (DONE)
+             * - processed a stop opcode (IDLE)
+             * - encountered an error (IDLE)
+             */
+            if ((GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_IDLE) ||
+                (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_DONE)) {
+                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed in "
+                              "shifter state = 0x%llx", GETFIELD(
+                        SPI_STS_SHIFTER_FSM, s->status));
+                /*
+                 * Set sequencer FSM error bit 3 (general_SPI_status[3])
+                 * in status reg.
+                 */
+                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
+                trace_pnv_spi_sequencer_stop_requested("invalid shifter state");
+                stop = true;
+            } else {
+                /*
+                 * Look for the special case where there is a shift_n1 set for
+                 * transmit and it is followed by a shift_n2 set for transmit
+                 * AND the combined transmit length of the two operations is
+                 * less than or equal to the size of the TDR register. In this
+                 * case we want to use both this current shift_n1 opcode and the
+                 * following shift_n2 opcode to assemble the frame for
+                 * transmission to the responder without requiring a refill of
+                 * the TDR between the two operations.
+                 */
+                if ((s->seq_op[get_seq_index(s) + 1] & 0xF0)
+                                == SEQ_OP_SHIFT_N2) {
+                    send_n1_alone = false;
+                }
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
+                                FSM_SHIFT_N1);
+                stop = operation_shiftn1(s, opcode, &payload, send_n1_alone);
+                if (stop) {
+                    /*
+                     *  The operation code says to stop, this can occur if:
+                     * (1) RDR is full and the N1 shift is set for receive
+                     * (2) TDR was empty at the time of the N1 shift so we need
+                     * to wait for data.
+                     * (3) Neither 1 nor 2 are occurring and we aren't sending
+                     * N1 alone and N2 counter reload is set (bit 0 of the N2
+                     * counter reload field).  In this case TDR_underrun will
+                     * will be set and the Payload has been loaded so it is
+                     * ok to advance the sequencer.
+                     */
+                    if (GETFIELD(SPI_STS_TDR_UNDERRUN, s->status)) {
+                        s->shift_n1_done = true;
+                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
+                                                  FSM_SHIFT_N2);
+                        s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
+                                        (get_seq_index(s) + 1));
+                    } else {
+                        /*
+                         * This is case (1) or (2) so the sequencer needs to
+                         * wait and NOT go to the next sequence yet.
+                         */
+                        s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
+                                        FSM_WAIT);
+                    }
+                } else {
+                    /* Ok to move on to the next index */
+                    s->shift_n1_done = true;
+                    next_sequencer_fsm(s);
+                }
+            }
+            break;
+
+        case SEQ_OP_SHIFT_N2:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("SHIFT_N2", get_seq_index(s));
+            if (!s->shift_n1_done) {
+                qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not allowed if a "
+                              "Shift_N1 is not done, shifter state = 0x%llx",
+                              GETFIELD(SPI_STS_SHIFTER_FSM, s->status));
+                /*
+                 * In case the sequencer actually stops if an N2 shift is
+                 * requested before any N1 shift is done. Set sequencer FSM
+                 * error bit 3 (general_SPI_status[3]) in status reg.
+                 */
+                s->status = SETFIELD(PPC_BIT(35), s->status, 1);
+                trace_pnv_spi_sequencer_stop_requested("shift_n2 "
+                                    "w/no shift_n1 done");
+                stop = true;
+            } else {
+                /* Ok to do a Shift_N2 */
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
+                                FSM_SHIFT_N2);
+                stop = operation_shiftn2(s, opcode, &payload);
+                /*
+                 * If the operation code says to stop set the shifter state to
+                 * wait and stop
+                 */
+                if (stop) {
+                    s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status,
+                                    FSM_WAIT);
+                } else {
+                    /* Ok to move on to the next index */
+                    next_sequencer_fsm(s);
+                }
+            }
+            break;
+
+        case SEQ_OP_BRANCH_IFNEQ_RDR:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_RDR", get_seq_index(s));
+            /*
+             * The memory mapping register RDR match value is compared against
+             * the 16 rightmost bytes of the RDR (potentially with masking).
+             * Since this comparison is performed against the contents of the
+             * RDR then a receive must have previously occurred otherwise
+             * there is no data to compare and the operation cannot be
+             * completed and will stop the sequencer until RDR full is set to
+             * 1.
+             */
+            if (GETFIELD(SPI_STS_RDR_FULL, s->status) == 1) {
+                bool rdr_matched = false;
+                rdr_matched = does_rdr_match(s);
+                if (rdr_matched) {
+                    trace_pnv_spi_RDR_match("success");
+                    /* A match occurred, increment the sequencer index. */
+                    next_sequencer_fsm(s);
+                } else {
+                    trace_pnv_spi_RDR_match("failed");
+                    /*
+                     * Branch the sequencer to the index coded into the op
+                     * code.
+                     */
+                    s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
+                                    (opcode & 0x7));
+                }
+                /*
+                 * Regardless of where the branch ended up we want the
+                 * sequencer to continue shifting so we have to clear
+                 * RDR_full.
+                 */
+                s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
+            } else {
+                trace_pnv_spi_sequencer_stop_requested("RDR not"
+                                "full for 0x6x opcode");
+                stop = true;
+                s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_WAIT);
+            }
+            break;
+
+        case SEQ_OP_TRANSFER_TDR:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not supported\n");
+            next_sequencer_fsm(s);
+            break;
+
+        case SEQ_OP_BRANCH_IFNEQ_INC_1:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_1", get_seq_index(s));
+            /*
+             * The spec says the loop should execute count compare + 1 times.
+             * However we learned from engineering that we really only loop
+             * count_compare times, count compare = 0 makes this op code a
+             * no-op
+             */
+            if (s->loop_counter_1 !=
+                GETFIELD(SPI_CTR_CFG_CMP1, s->regs[SPI_CTR_CFG_REG])) {
+                /*
+                 * Next index is the lower nibble of the branch operation ID,
+                 * mask off all but the first three bits so we don't try to
+                 * access beyond the sequencer_operation_reg boundary.
+                 */
+                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
+                                (opcode & 0x7));
+                s->loop_counter_1++;
+            } else {
+                /* Continue to next index if loop counter is reached */
+                next_sequencer_fsm(s);
+            }
+            break;
+
+        case SEQ_OP_BRANCH_IFNEQ_INC_2:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            trace_pnv_spi_sequencer_op("BRANCH_IFNEQ_INC_2", get_seq_index(s));
+            uint8_t condition2 = GETFIELD(SPI_CTR_CFG_CMP2,
+                              s->regs[SPI_CTR_CFG_REG]);
+            /*
+             * The spec says the loop should execute count compare + 1 times.
+             * However we learned from engineering that we really only loop
+             * count_compare times, count compare = 0 makes this op code a
+             * no-op
+             */
+            if (s->loop_counter_2 != condition2) {
+                /*
+                 * Next index is the lower nibble of the branch operation ID,
+                 * mask off all but the first three bits so we don't try to
+                 * access beyond the sequencer_operation_reg boundary.
+                 */
+                s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status,
+                                          (opcode & 0x7));
+                s->loop_counter_2++;
+            } else {
+                /* Continue to next index if loop counter is reached */
+                next_sequencer_fsm(s);
+            }
+            break;
+
+        default:
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_EXECUTE);
+            /* Ignore unsupported operations. */
+            next_sequencer_fsm(s);
+            break;
+        } /* end of switch */
+        /*
+         * If we used all 8 opcodes without seeing a 00 - STOP in the sequence
+         * we need to go ahead and end things as if there was a STOP at the
+         * end.
+         */
+        if (get_seq_index(s) == 8) {
+            /* All 8 opcodes completed, sequencer idling */
+            s->status = SETFIELD(SPI_STS_SHIFTER_FSM, s->status, FSM_IDLE);
+            s->status = SETFIELD(SPI_STS_SEQ_INDEX, s->status, 0);
+            s->loop_counter_1 = 0;
+            s->loop_counter_2 = 0;
+            s->status = SETFIELD(SPI_STS_SEQ_FSM, s->status, SEQ_STATE_IDLE);
+            break;
+        }
+        /* Break the loop if a stop was requested */
+        if (stop) {
+            break;
+        }
+    } /* end of while */
+    return;
+} /* end of operation_sequencer() */
+
+/*
+ * The SPIC engine and its internal sequencer can be interrupted and reset by
+ * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive
+ * Miscellaneous Register of sbe_register_bo device.
+ * Reset immediately aborts any SPI transaction in progress and returns the
+ * sequencer and state machines to idle state.
+ * The configuration register values are not changed. The status register is
+ * not reset. The engine registers are not reset.
+ * The SPIC engine reset does not have any affect on the attached devices.
+ * Reset handling of any attached devices is beyond the scope of the engine.
+ */
+static void do_reset(DeviceState *dev)
+{
+    PnvSpi *s = PNV_SPI(dev);
+
+    trace_pnv_spi_reset();
+
+    /* Reset all N1 and N2 counters, and other constants */
+    s->N2_bits = 0;
+    s->N2_bytes = 0;
+    s->N2_tx = 0;
+    s->N2_rx = 0;
+    s->N1_bits = 0;
+    s->N1_bytes = 0;
+    s->N1_tx = 0;
+    s->N1_rx = 0;
+    s->loop_counter_1 = 0;
+    s->loop_counter_2 = 0;
+    /* Disconnected from responder */
+    qemu_set_irq(s->cs_line[0], 1);
+}
+
 static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr, unsigned size)
 {
     PnvSpi *s = PNV_SPI(opaque);
@@ -36,6 +1067,10 @@  static uint64_t pnv_spi_xscom_read(void *opaque, hwaddr addr, unsigned size)
         val = s->regs[reg];
         trace_pnv_spi_read_RDR(val);
         s->status = SETFIELD(SPI_STS_RDR_FULL, s->status, 0);
+        if (GETFIELD(SPI_STS_SHIFTER_FSM, s->status) == FSM_WAIT) {
+            trace_pnv_spi_start_sequencer();
+            operation_sequencer(s);
+        }
         break;
     case SPI_SEQ_OP_REG:
         val = 0;
@@ -97,6 +1132,8 @@  static void pnv_spi_xscom_write(void *opaque, hwaddr addr,
         trace_pnv_spi_write_TDR(val);
         s->status = SETFIELD(SPI_STS_TDR_FULL, s->status, 1);
         s->status = SETFIELD(SPI_STS_TDR_UNDERRUN, s->status, 0);
+        trace_pnv_spi_start_sequencer();
+        operation_sequencer(s);
         break;
     case SPI_SEQ_OP_REG:
         for (int i = 0; i < PNV_SPI_REG_SIZE; i++) {
@@ -129,6 +1166,7 @@  static const MemoryRegionOps pnv_spi_xscom_ops = {
 
 static Property pnv_spi_properties[] = {
     DEFINE_PROP_UINT32("spic_num", PnvSpi, spic_num, 0),
+    DEFINE_PROP_UINT8("transfer_len", PnvSpi, transfer_len, 4),
     DEFINE_PROP_END_OF_LIST(),
 };
 
@@ -180,6 +1218,7 @@  static void pnv_spi_class_init(ObjectClass *klass, void *data)
 
     dc->desc = "PowerNV SPI";
     dc->realize = pnv_spi_realize;
+    dc->reset = do_reset;
     device_class_set_props(dc, pnv_spi_properties);
 }
 
diff --git a/hw/ssi/trace-events b/hw/ssi/trace-events
index 4388024a05..7fa27ebade 100644
--- a/hw/ssi/trace-events
+++ b/hw/ssi/trace-events
@@ -38,3 +38,18 @@  pnv_spi_read(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val 0x%" PRIx64
 pnv_spi_write(uint64_t addr, uint64_t val) "addr 0x%" PRIx64 " val 0x%" PRIx64
 pnv_spi_read_RDR(uint64_t val) "data extracted = 0x%" PRIx64
 pnv_spi_write_TDR(uint64_t val) "being written, data written = 0x%" PRIx64
+pnv_spi_start_sequencer(void) ""
+pnv_spi_reset(void) "spic engine sequencer configuration and spi communication"
+pnv_spi_sequencer_op(const char* op, uint8_t index) "%s at index = 0x%x"
+pnv_spi_shifter_stating(void) "pull CS line low"
+pnv_spi_shifter_done(void) "pull the CS line high"
+pnv_spi_log_Ncounts(uint8_t N1_bits, uint8_t N1_bytes, uint8_t N1_tx, uint8_t N1_rx, uint8_t N2_bits, uint8_t N2_bytes, uint8_t N2_tx, uint8_t N2_rx) "N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx = %d, N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d"
+pnv_spi_tx_append(const char* frame, uint8_t byte, uint8_t tdr_index) "%s = 0x%2.2x to payload from TDR at index %d"
+pnv_spi_tx_append_FF(const char* frame) "%s to Payload"
+pnv_spi_tx_request(const char* frame, uint32_t payload_len) "%s, payload len = %d"
+pnv_spi_rx_received(uint32_t payload_len) "payload len = %d"
+pnv_spi_rx_read_N1frame(void) ""
+pnv_spi_rx_read_N2frame(void) ""
+pnv_spi_shift_rx(uint8_t byte, uint32_t index) "byte = 0x%2.2x into RDR from payload index %d"
+pnv_spi_sequencer_stop_requested(const char* reason) "due to %s"
+pnv_spi_RDR_match(const char* result) "%s"