@@ -327,6 +327,17 @@ define Build/netgear-dni
mv $@.new $@
endef
+define Build/tplink-safe
+ $(STAGING_DIR_HOST)/bin/tplink-safeloader \
+ -B $(TPLINK_BOARD_ID) -V OpenWrt.$(REVISION) \
+ -k $(word 1,$^) \
+ -r $(word 2,$^) \
+ -j \
+ $(if $(findstring sysupgrade,$1),-S) \
+ -o $@.new
+ mv $@.new $@
+endef
+
define Build/fit
$(TOPDIR)/scripts/mkits.sh \
-D $(DEVICE_NAME) -o $@.its -k $@ \
new file mode 100644
@@ -0,0 +1,15 @@
+diff -ur ../../old/compat-wireless-2015-12-03/drivers/net/wireless/ath/ath10k/core.c ./drivers/net/wireless/ath/ath10k/core.c
+--- a/drivers/net/wireless/ath/ath10k/core.c 2015-12-06 23:36:07.696995166 +0100
++++ b/drivers/net/wireless/ath/ath10k/core.c 2015-12-07 00:01:50.390388435 +0100
+@@ -1800,9 +1800,9 @@
+
+ ret = ath10k_core_get_board_id_from_otp(ar);
+ if (ret && ret != -EOPNOTSUPP) {
+- ath10k_err(ar, "failed to get board id from otp: %d\n",
++ ath10k_err(ar, "failed to get board id from otp: %d, ignoring\n",
+ ret);
+- return ret;
++// return ret;
+ }
+
+ ret = ath10k_core_fetch_board_file(ar);
@@ -19,6 +19,13 @@ r7500)
ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0"
ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0"
;;
+c2600)
+ ucidef_set_led_usbdev "usb1" "USB 1" "usb_2:blue" "2-1"
+ ucidef_set_led_usbdev "usb2" "USB 2" "usb_4:blue" "4-1"
+ ucidef_set_led_netdev "wan" "WAN" "wan:blue" "eth0"
+ ucidef_set_led_netdev "lan" "LAN" "lan:blue" "br-lan"
+ ucidef_set_led_default "general" "general" "ledgnr:blue" "1"
+ ;;
*)
;;
esac
@@ -13,7 +13,8 @@ board=$(ipq806x_board_name)
case "$board" in
ap148 |\
-r7500)
+r7500 |\
+c2600)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
new file mode 100644
@@ -0,0 +1,66 @@
+#!/bin/sh
+
+ath10kcal_die() {
+ echo "ath10cal: " "$*"
+ exit 1
+}
+
+ath10kcal_from_file() {
+ local source=$1
+ local offset=$2
+ local count=$3
+
+ dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+ ath10kcal_die "failed to extract calibration data from $source"
+}
+
+ath10kcal_extract() {
+ local part=$1
+ local offset=$2
+ local count=$3
+ local mtd
+
+ mtd=$(find_mtd_chardev $part)
+ [ -n "$mtd" ] || \
+ ath10kcal_die "no mtd device found for partition $part"
+
+ dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+ ath10kcal_die "failed to extract calibration data from $mtd"
+}
+
+ath10kcal_patch_mac() {
+ local mac=$1
+
+ [ -z "$mac" ] && return
+
+ macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
+}
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/ipq806x.sh
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(ipq806x_board_name)
+
+
+case "$FIRMWARE" in
+"ath10k/cal-pci-0000:01:00.0.bin")
+ case $board in
+ c2600)
+ ath10kcal_extract "0:ART" 4096 12064
+ ;;
+ esac
+ ;;
+"ath10k/cal-pci-0001:01:00.0.bin")
+ case $board in
+ c2600)
+ ath10kcal_extract "0:ART" 20480 12064
+ ;;
+ esac
+ ;;
+*)
+ exit 1
+ ;;
+esac
@@ -23,6 +23,9 @@ ipq806x_board_detect() {
*"R7500")
name="r7500"
;;
+ *"C2600")
+ name="c2600"
+ ;;
esac
[ -z "$name" ] && name="unknown"
@@ -11,6 +11,14 @@ platform_check_image() {
nand_do_platform_check $board $1
return $?;
;;
+ c2600)
+ local magic_long="$(get_magic_long "$1")"
+ [ "$magic_long" != "27051956" ] && {
+ echo "Invalid image, bad magic: $magic_long"
+ return 1
+ }
+ return 0;
+ ;;
*)
return 1;
esac
@@ -27,4 +35,28 @@ platform_pre_upgrade() {
esac
}
-# use default for platform_do_upgrade()
+platform_do_upgrade() {
+ local board=$(ipq806x_board_name)
+
+ case "$board" in
+ c2600)
+ platform_do_upgrade_c2600 "$ARGV"
+ ;;
+ esac
+}
+
+platform_do_upgrade_c2600() {
+ local kernpart="0:HLOS"
+ local rootfspart="rootfs"
+
+ local kernel_mtd="$(find_mtd_index $kernpart)"
+
+ local kerndev="/dev/mtd${kernel_mtd}"
+ local rootfsdev=$rootfspart
+
+ PART_NAME="${kerndev}:${rootfsdev}"
+ MTD_CONFIG_ARGS="-s 0x200000"
+
+ default_do_upgrade "$ARGV"
+
+}
@@ -85,6 +85,19 @@ define Device/DniImage
endef
DEVICE_VARS += KERNEL_SIZE NETGEAR_BOARD_ID NETGEAR_HW_ID DEVICE_BLOCK_SIZE DEVICE_PAGE_SIZE
+define Device/TpSafeImage
+ PROFILES += $$(DEVICE_NAME)
+ FILESYSTEMS := squashfs
+ KERNEL_SUFFIX := -uImage
+ KERNEL = kernel-bin | append-dtb | uImage none
+ KERNEL_NAME := zImage
+ TPLINK_BOARD_ID :=
+ IMAGES := factory.bin sysupgrade.bin
+ IMAGE/factory.bin := tplink-safe factory
+ IMAGE/sysupgrade.bin := tplink-safe sysupgrade
+endef
+DEVICE_VARS += TPLINK_BOARD_ID
+
define Device/AP148
$(call Device/FitImage)
$(call Device/UbiFit)
@@ -103,6 +116,15 @@ define Device/AP148-legacy
BOARD_NAME := ap148
endef
+define Device/C2600
+ $(call Device/TpSafeImage)
+ DEVICE_DTS := qcom-ipq8064-c2600
+ BLOCKSIZE := 128KiB
+ PAGESIZE := 2048
+ BOARD_NAME := c2600
+ TPLINK_BOARD_ID := C2600
+endef
+
define Device/DB149
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq8064-db149
@@ -121,6 +143,6 @@ define Device/R7500
BOARD_NAME := r7500
endef
-TARGET_DEVICES += AP148 AP148-legacy DB149 R7500
+TARGET_DEVICES += AP148 AP148-legacy C2600 DB149 R7500
$(eval $(call BuildImage))
new file mode 100644
@@ -0,0 +1,300 @@
+diff -urN a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
+--- a/arch/arm/boot/dts/Makefile 2015-11-25 22:51:15.148899604 +0100
++++ b/arch/arm/boot/dts/Makefile 2015-12-06 14:33:31.092396982 +0100
+@@ -362,6 +362,7 @@
+ qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-r7500.dtb \
++ qcom-ipq8064-c2600.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
+ qcom-msm8974-sony-xperia-honami.dtb
+diff -urN a/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
+--- a/arch/arm/boot/dts/qcom-ipq8064-c2600.dts 1970-01-01 01:00:00.000000000 +0100
++++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts 2015-12-06 14:20:05.152365670 +0100
+@@ -0,0 +1,285 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "TP-Link Archer C2600";
++ compatible = "tplink,c2600", "qcom,ipq8064";
++
++ memory@0 {
++ reg = <0x42000000 0x1e000000>;
++ device_type = "memory";
++ };
++
++ reserved-memory {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++ rsvd@41200000 {
++ reg = <0x41200000 0x300000>;
++ no-map;
++ };
++ };
++
++ aliases {
++ serial0 = &uart4;
++ mdio-gpio0 = &mdio0;
++ };
++
++ chosen {
++ linux,stdout-path = "serial0:115200n8";
++ };
++
++ soc {
++ pinmux@800000 {
++ i2c4_pins: i2c4_pinmux {
++ pins = "gpio12", "gpio13";
++ function = "gsbi4";
++ bias-disable;
++ };
++
++ spi_pins: spi_pins {
++ mux {
++ pins = "gpio18", "gpio19", "gpio21";
++ function = "gsbi5";
++ drive-strength = <10>;
++ bias-none;
++ };
++ };
++
++ nand_pins: nand_pins {
++ mux {
++ pins = "gpio34", "gpio35", "gpio36",
++ "gpio37", "gpio38", "gpio39",
++ "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ function = "nand";
++ drive-strength = <10>;
++ bias-disable;
++ };
++
++ pullups {
++ pins = "gpio39";
++ bias-pull-up;
++ };
++
++ hold {
++ pins = "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ bias-bus-hold;
++ };
++ };
++
++ mdio0_pins: mdio0_pins {
++ mux {
++ pins = "gpio0", "gpio1";
++ function = "gpio";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
++ rgmii2_pins: rgmii2_pins {
++ mux {
++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++ function = "rgmii2";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++ };
++
++ gsbi@16300000 {
++ qcom,mode = <GSBI_PROT_I2C_UART>;
++ status = "ok";
++ serial@16340000 {
++ status = "ok";
++ };
++ /*
++ * The i2c device on gsbi4 should not be enabled.
++ * On ipq806x designs gsbi4 i2c is meant for exclusive
++ * RPM usage. Turning this on in kernel manifests as
++ * i2c failure for the RPM.
++ */
++ };
++
++ gsbi5: gsbi@1a200000 {
++ qcom,mode = <GSBI_PROT_SPI>;
++ status = "ok";
++
++ spi4: spi@1a280000 {
++ status = "ok";
++ spi-max-frequency = <50000000>;
++
++ pinctrl-0 = <&spi_pins>;
++ pinctrl-names = "default";
++
++ cs-gpios = <&qcom_pinmux 20 0>;
++
++ flash: m25p80@0 {
++ compatible = "s25fl256s1";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ spi-max-frequency = <50000000>;
++ reg = <0>;
++
++ linux,part-probe = "qcom-smem";
++ };
++ };
++ };
++
++ phy@100f8800 { /* USB3 port 1 HS phy */
++ status = "ok";
++ };
++
++ phy@100f8830 { /* USB3 port 1 SS phy */
++ status = "ok";
++ };
++
++ phy@110f8800 { /* USB3 port 0 HS phy */
++ status = "ok";
++ };
++
++ phy@110f8830 { /* USB3 port 0 SS phy */
++ status = "ok";
++ };
++
++ usb30@0 {
++ status = "ok";
++ };
++
++ usb30@1 {
++ status = "ok";
++ };
++
++ pcie0: pci@1b500000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ pcie1: pci@1b700000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ mdio0: mdio {
++ compatible = "virtual,mdio-gpio";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++ pinctrl-0 = <&mdio0_pins>;
++ pinctrl-names = "default";
++
++ phy0: ethernet-phy@0 {
++ device_type = "ethernet-phy";
++ reg = <0>;
++ qca,ar8327-initvals = <
++ 0x00004 0x7600000 /* PAD0_MODE */
++ 0x00008 0x1000000 /* PAD5_MODE */
++ 0x0000c 0x80 /* PAD6_MODE */
++ 0x000e4 0xaa545 /* MAC_POWER_SEL */
++ 0x000e0 0xc74164de /* SGMII_CTRL */
++ 0x0007c 0x4e /* PORT0_STATUS */
++ 0x00094 0x4e /* PORT6_STATUS */
++ >;
++ };
++
++ phy4: ethernet-phy@4 {
++ device_type = "ethernet-phy";
++ reg = <4>;
++ };
++ };
++
++ gmac1: ethernet@37200000 {
++ status = "ok";
++ phy-mode = "rgmii";
++ qcom,id = <1>;
++
++ pinctrl-0 = <&rgmii2_pins>;
++ pinctrl-names = "default";
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ gmac2: ethernet@37400000 {
++ status = "ok";
++ phy-mode = "sgmii";
++ qcom,id = <2>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ wifi {
++ label = "wifi";
++ gpios = <&qcom_pinmux 49 1>;
++ linux,code = <KEY_WLAN>;
++ };
++
++ reset {
++ label = "reset";
++ gpios = <&qcom_pinmux 64 1>;
++ linux,code = <KEY_RESTART>;
++ };
++
++ wps {
++ label = "wps";
++ gpios = <&qcom_pinmux 65 1>;
++ linux,code = <KEY_WPS_BUTTON>;
++ };
++ ledgeneral {
++ label = "ledgeneral";
++ gpios = <&qcom_pinmux 16 1>;
++ linux,code = <KEY_DOLLAR>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ lan {
++ label = "lan:blue";
++ gpios = <&qcom_pinmux 6 0>;
++ };
++ usb4 {
++ label = "usb_4:blue";
++ gpios = <&qcom_pinmux 7 0>;
++ };
++ usb2 {
++ label = "usb_2:blue";
++ gpios = <&qcom_pinmux 8 0>;
++ };
++ wps {
++ label = "wps:blue";
++ gpios = <&qcom_pinmux 9 0>;
++ };
++ wan_blue {
++ label = "wan:blue";
++ gpios = <&qcom_pinmux 33 1>;
++ };
++ status {
++ label = "status:blue";
++ gpios = <&qcom_pinmux 53 0>;
++ default-state = "on";
++ };
++ ledgnr {
++ label = "ledgnr:blue";
++ gpios = <&qcom_pinmux 66 0>;
++ };
++ };
++};
++
++&adm_dma {
++ status = "ok";
++};
new file mode 100644
@@ -0,0 +1,300 @@
+diff -urN a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
+--- a/arch/arm/boot/dts/Makefile 2015-11-25 22:51:15.148899604 +0100
++++ b/arch/arm/boot/dts/Makefile 2015-12-06 14:33:31.092396982 +0100
+@@ -453,6 +453,7 @@
+ qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-r7500.dtb \
++ qcom-ipq8064-c2600.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
+ qcom-msm8974-sony-xperia-honami.dtb
+diff -urN a/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
+--- a/arch/arm/boot/dts/qcom-ipq8064-c2600.dts 1970-01-01 01:00:00.000000000 +0100
++++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts 2015-12-06 14:20:05.152365670 +0100
+@@ -0,0 +1,285 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "TP-Link Archer C2600";
++ compatible = "tplink,c2600", "qcom,ipq8064";
++
++ memory@0 {
++ reg = <0x42000000 0x1e000000>;
++ device_type = "memory";
++ };
++
++ reserved-memory {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++ rsvd@41200000 {
++ reg = <0x41200000 0x300000>;
++ no-map;
++ };
++ };
++
++ aliases {
++ serial0 = &uart4;
++ mdio-gpio0 = &mdio0;
++ };
++
++ chosen {
++ linux,stdout-path = "serial0:115200n8";
++ };
++
++ soc {
++ pinmux@800000 {
++ i2c4_pins: i2c4_pinmux {
++ pins = "gpio12", "gpio13";
++ function = "gsbi4";
++ bias-disable;
++ };
++
++ spi_pins: spi_pins {
++ mux {
++ pins = "gpio18", "gpio19", "gpio21";
++ function = "gsbi5";
++ drive-strength = <10>;
++ bias-none;
++ };
++ };
++
++ nand_pins: nand_pins {
++ mux {
++ pins = "gpio34", "gpio35", "gpio36",
++ "gpio37", "gpio38", "gpio39",
++ "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ function = "nand";
++ drive-strength = <10>;
++ bias-disable;
++ };
++
++ pullups {
++ pins = "gpio39";
++ bias-pull-up;
++ };
++
++ hold {
++ pins = "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ bias-bus-hold;
++ };
++ };
++
++ mdio0_pins: mdio0_pins {
++ mux {
++ pins = "gpio0", "gpio1";
++ function = "gpio";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
++ rgmii2_pins: rgmii2_pins {
++ mux {
++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++ function = "rgmii2";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++ };
++
++ gsbi@16300000 {
++ qcom,mode = <GSBI_PROT_I2C_UART>;
++ status = "ok";
++ serial@16340000 {
++ status = "ok";
++ };
++ /*
++ * The i2c device on gsbi4 should not be enabled.
++ * On ipq806x designs gsbi4 i2c is meant for exclusive
++ * RPM usage. Turning this on in kernel manifests as
++ * i2c failure for the RPM.
++ */
++ };
++
++ gsbi5: gsbi@1a200000 {
++ qcom,mode = <GSBI_PROT_SPI>;
++ status = "ok";
++
++ spi4: spi@1a280000 {
++ status = "ok";
++ spi-max-frequency = <50000000>;
++
++ pinctrl-0 = <&spi_pins>;
++ pinctrl-names = "default";
++
++ cs-gpios = <&qcom_pinmux 20 0>;
++
++ flash: m25p80@0 {
++ compatible = "s25fl256s1";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ spi-max-frequency = <50000000>;
++ reg = <0>;
++
++ linux,part-probe = "qcom-smem";
++ };
++ };
++ };
++
++ phy@100f8800 { /* USB3 port 1 HS phy */
++ status = "ok";
++ };
++
++ phy@100f8830 { /* USB3 port 1 SS phy */
++ status = "ok";
++ };
++
++ phy@110f8800 { /* USB3 port 0 HS phy */
++ status = "ok";
++ };
++
++ phy@110f8830 { /* USB3 port 0 SS phy */
++ status = "ok";
++ };
++
++ usb30@0 {
++ status = "ok";
++ };
++
++ usb30@1 {
++ status = "ok";
++ };
++
++ pcie0: pci@1b500000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ pcie1: pci@1b700000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ mdio0: mdio {
++ compatible = "virtual,mdio-gpio";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++ pinctrl-0 = <&mdio0_pins>;
++ pinctrl-names = "default";
++
++ phy0: ethernet-phy@0 {
++ device_type = "ethernet-phy";
++ reg = <0>;
++ qca,ar8327-initvals = <
++ 0x00004 0x7600000 /* PAD0_MODE */
++ 0x00008 0x1000000 /* PAD5_MODE */
++ 0x0000c 0x80 /* PAD6_MODE */
++ 0x000e4 0xaa545 /* MAC_POWER_SEL */
++ 0x000e0 0xc74164de /* SGMII_CTRL */
++ 0x0007c 0x4e /* PORT0_STATUS */
++ 0x00094 0x4e /* PORT6_STATUS */
++ >;
++ };
++
++ phy4: ethernet-phy@4 {
++ device_type = "ethernet-phy";
++ reg = <4>;
++ };
++ };
++
++ gmac1: ethernet@37200000 {
++ status = "ok";
++ phy-mode = "rgmii";
++ qcom,id = <1>;
++
++ pinctrl-0 = <&rgmii2_pins>;
++ pinctrl-names = "default";
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ gmac2: ethernet@37400000 {
++ status = "ok";
++ phy-mode = "sgmii";
++ qcom,id = <2>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ wifi {
++ label = "wifi";
++ gpios = <&qcom_pinmux 49 1>;
++ linux,code = <KEY_WLAN>;
++ };
++
++ reset {
++ label = "reset";
++ gpios = <&qcom_pinmux 64 1>;
++ linux,code = <KEY_RESTART>;
++ };
++
++ wps {
++ label = "wps";
++ gpios = <&qcom_pinmux 65 1>;
++ linux,code = <KEY_WPS_BUTTON>;
++ };
++ ledgeneral {
++ label = "ledgeneral";
++ gpios = <&qcom_pinmux 16 1>;
++ linux,code = <KEY_DOLLAR>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ lan {
++ label = "lan:blue";
++ gpios = <&qcom_pinmux 6 0>;
++ };
++ usb4 {
++ label = "usb_4:blue";
++ gpios = <&qcom_pinmux 7 0>;
++ };
++ usb2 {
++ label = "usb_2:blue";
++ gpios = <&qcom_pinmux 8 0>;
++ };
++ wps {
++ label = "wps:blue";
++ gpios = <&qcom_pinmux 9 0>;
++ };
++ wan_blue {
++ label = "wan:blue";
++ gpios = <&qcom_pinmux 33 1>;
++ };
++ status {
++ label = "status:blue";
++ gpios = <&qcom_pinmux 53 0>;
++ default-state = "on";
++ };
++ ledgnr {
++ label = "ledgnr:blue";
++ gpios = <&qcom_pinmux 66 0>;
++ };
++ };
++};
++
++&adm_dma {
++ status = "ok";
++};
new file mode 100644
@@ -0,0 +1,20 @@
+#
+# Copyright (c) 2014 The Linux Foundation. All rights reserved.
+# Copyright (C) 2009 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/C2600
+ NAME:=TP-Link Archer C2600
+ PACKAGES:= \
+ kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
+ kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
+ kmod-ath10k ath10k-firmware-qca99x0 wpad-mini
+endef
+
+define Profile/C2600/Description
+ Package set for the TP-Link Archer C2600.
+endef
+$(eval $(call Profile,C2600))
@@ -105,6 +105,8 @@ static const uint8_t md5_salt[16] = {
/** Vendor information for CPE210/220/510/520 */
static const char cpe510_vendor[] = "CPE510(TP-LINK|UN|N300-5):1.0\r\n";
+/** Vendor information for C2600 */
+static const char c2600_vendor[] = "";
/**
The flash partition table for CPE210/220/510/520;
@@ -128,6 +130,39 @@ static const struct flash_partition_entry cpe510_partitions[] = {
};
/**
+ The flash partition table for C2600;
+ it is the same as the one used by the stock images.
+*/
+static const struct flash_partition_entry c2600_partitions[] = {
+ {"SBL1", 0x00000, 0x20000},
+ {"MIBIB", 0x20000, 0x20000},
+ {"SBL2", 0x40000, 0x20000},
+ {"SBL3", 0x60000, 0x30000},
+ {"DDRCONFIG", 0x90000, 0x10000},
+ {"SSD", 0xa0000, 0x10000},
+ {"TZ", 0xb0000, 0x30000},
+ {"RPM", 0xe0000, 0x20000},
+ {"fs-uboot", 0x100000, 0x70000},
+ {"uboot-env", 0x170000, 0x40000},
+ {"radio", 0x1b0000, 0x40000},
+ {"os-image", 0x1f0000, 0x200000},
+ {"file-system", 0x3f0000, 0x1b00000},
+ {"default-mac", 0x1ef0000, 0x00200},
+ {"pin", 0x1ef0200, 0x00200},
+ {"product-info", 0x1ef0400, 0x0fc00},
+ {"partition-table", 0x1f00000, 0x10000},
+ {"soft-version", 0x1f10000, 0x10000},
+ {"support-list", 0x1f20000, 0x10000},
+ {"profile", 0x1f30000, 0x10000},
+ {"default-config", 0x1f40000, 0x10000},
+ {"user-config", 0x1f50000, 0x40000},
+ {"qos-db", 0x1f90000, 0x40000},
+ {"usb-config", 0x1fd0000, 0x10000},
+ {"log", 0x1fe0000, 0x20000},
+ {NULL, 0, 0}
+};
+
+/**
The support list for CPE210/220/510/520
*/
static const char cpe510_support_list[] =
@@ -141,6 +176,13 @@ static const char cpe510_support_list[] =
"CPE220(TP-LINK|UN|N300-2):1.0\r\n"
"CPE220(TP-LINK|UN|N300-2):1.1\r\n";
+/**
+ The support list for C2600
+*/
+static const char c2600_support_list[] =
+ "SupportList:\r\n"
+ "{product_name:Archer C2600,product_ver:1.0.0,special_id:00000000}\r\n";
+
#define error(_ret, _errno, _str, ...) \
do { \
fprintf(stderr, _str ": %s\n", ## __VA_ARGS__, \
@@ -240,14 +282,14 @@ static struct image_partition_entry make_soft_version(uint32_t rev) {
}
/** Generates the support-list partition */
-static struct image_partition_entry make_support_list(const char *support_list) {
+static struct image_partition_entry make_support_list(const char *support_list, bool trailzero) {
size_t len = strlen(support_list);
struct image_partition_entry entry = alloc_image_partition("support-list", len + 9);
put32(entry.data, len);
memset(entry.data+4, 0, 4);
memcpy(entry.data+8, support_list, len);
- entry.data[len+8] = '\xff';
+ entry.data[len+8] = trailzero ? '\x00' : '\xff';
return entry;
}
@@ -436,6 +478,37 @@ static void * generate_sysupgrade_image(const struct flash_partition_entry *flas
return image;
}
+static void * generate_sysupgrade_image_c2600(const struct flash_partition_entry *flash_parts, const struct image_partition_entry *image_parts, size_t *len) {
+ const struct flash_partition_entry *flash_os_image = &flash_parts[11];
+ const struct flash_partition_entry *flash_file_system = &flash_parts[12];
+
+ const struct image_partition_entry *image_os_image = &image_parts[3];
+ const struct image_partition_entry *image_file_system = &image_parts[4];
+
+ assert(strcmp(flash_os_image->name, "os-image") == 0);
+ assert(strcmp(flash_file_system->name, "file-system") == 0);
+
+ assert(strcmp(image_os_image->name, "os-image") == 0);
+ assert(strcmp(image_file_system->name, "file-system") == 0);
+
+ if (image_os_image->size > flash_os_image->size)
+ error(1, 0, "kernel image too big (more than %u bytes)", (unsigned)flash_os_image->size);
+ if (image_file_system->size > flash_file_system->size)
+ error(1, 0, "rootfs image too big (more than %u bytes)", (unsigned)flash_file_system->size);
+
+ *len = flash_file_system->base - flash_os_image->base + image_file_system->size;
+
+ uint8_t *image = malloc(*len);
+ if (!image)
+ error(1, errno, "malloc");
+
+ memset(image, 0xff, *len);
+
+ memcpy(image, image_os_image->data, image_os_image->size);
+ memcpy(image + flash_file_system->base - flash_os_image->base, image_file_system->data, image_file_system->size);
+
+ return image;
+}
/** Generates an image for CPE210/220/510/520 and writes it to a file */
static void do_cpe510(const char *output, const char *kernel_image, const char *rootfs_image, uint32_t rev, bool add_jffs2_eof, bool sysupgrade) {
@@ -443,7 +516,7 @@ static void do_cpe510(const char *output, const char *kernel_image, const char *
parts[0] = make_partition_table(cpe510_partitions);
parts[1] = make_soft_version(rev);
- parts[2] = make_support_list(cpe510_support_list);
+ parts[2] = make_support_list(cpe510_support_list,false);
parts[3] = read_file("os-image", kernel_image, false);
parts[4] = read_file("file-system", rootfs_image, add_jffs2_eof);
@@ -470,6 +543,39 @@ static void do_cpe510(const char *output, const char *kernel_image, const char *
free_image_partition(parts[i]);
}
+/** Generates an image for C2600 and writes it to a file */
+static void do_c2600(const char *output, const char *kernel_image, const char *rootfs_image, uint32_t rev, bool add_jffs2_eof, bool sysupgrade) {
+ struct image_partition_entry parts[6] = {};
+
+ parts[0] = make_partition_table(c2600_partitions);
+ parts[1] = make_soft_version(rev);
+ parts[2] = make_support_list(c2600_support_list,true);
+ parts[3] = read_file("os-image", kernel_image, false);
+ parts[4] = read_file("file-system", rootfs_image, add_jffs2_eof);
+
+ size_t len;
+ void *image;
+ if (sysupgrade)
+ image = generate_sysupgrade_image_c2600(c2600_partitions, parts, &len);
+ else
+ image = generate_factory_image(c2600_vendor, parts, &len);
+
+ FILE *file = fopen(output, "wb");
+ if (!file)
+ error(1, errno, "unable to open output file");
+
+ if (fwrite(image, len, 1, file) != 1)
+ error(1, 0, "unable to write output file");
+
+ fclose(file);
+
+ free(image);
+
+ size_t i;
+ for (i = 0; parts[i].name; i++)
+ free_image_partition(parts[i]);
+}
+
/** Usage output */
static void usage(const char *argv0) {
@@ -552,6 +658,8 @@ int main(int argc, char *argv[]) {
if (strcmp(board, "CPE510") == 0)
do_cpe510(output, kernel_image, rootfs_image, rev, add_jffs2_eof, sysupgrade);
+ else if (strcmp(board, "C2600") == 0)
+ do_c2600(output, kernel_image, rootfs_image, rev, add_jffs2_eof, sysupgrade);
else
error(1, 0, "unsupported board %s", board);