new file mode 100644
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9342_ubnt_xw.dtsi"
+
+/ {
+ compatible = "ubnt,powerbeam-m-xw", "ubnt,xw", "qca,ar9342";
+ model = "Ubiquiti PowerBeam M (XW)";
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <4>;
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ /* default for ar934x, except for 1000M and 10M */
+ pll-data = <0x02000000 0x00000101 0x00001313>;
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy4>;
+
+ gmac-config {
+ device = <&gmac>;
+ rxd-delay = <3>;
+ rxdv-delay = <3>;
+ };
+};
@@ -383,6 +383,7 @@ ubnt,nanostation-loco-m-xw|\
ubnt,nanostation-m|\
ubnt,nanostation-m-xw|\
ubnt,picostation-m|\
+ubnt,powerbeam-m-xw|\
ubnt,powerbridge-m|\
ubnt,rocket-m)
ucidef_set_rssimon "wlan0" "200000" "1"
@@ -85,6 +85,7 @@ ath79_setup_interfaces()
ubnt,picostation-m|\
ubnt,powerbeam-5ac-500|\
ubnt,powerbeam-5ac-gen2|\
+ ubnt,powerbeam-m-xw|\
ubnt,powerbridge-m|\
ubnt,rocket-m|\
ubnt,unifiac-lite|\
@@ -328,6 +328,14 @@ define Device/ubnt_powerbeam-5ac-gen2
endef
TARGET_DEVICES += ubnt_powerbeam-5ac-gen2
+define Device/ubnt_powerbeam-m-xw
+ $(Device/ubnt-xw)
+ DEVICE_MODEL := PowerBeam M
+ DEVICE_PACKAGES += rssileds
+ SUPPORTED_DEVICES += loco-m-xw
+endef
+TARGET_DEVICES += ubnt_powerbeam-m-xw
+
define Device/ubnt_powerbridge-m
$(Device/ubnt-xm)
SOC := ar7241
This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your device! Read the wiki for more info. - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first. - Upload the factory image via AirOS web GUI. Flashing via TFTP: - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your device! Read the wiki for more info. - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first. - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP since v1: * renamed from ubnt,powerbeam-m to ubnt,powerbeam-m-xw since v2: * removed redundant mtd-mac-address from dts Signed-off-by: Russell Senior <russell@personaltelco.net> --- .../ath79/dts/ar9342_ubnt_powerbeam-m-xw.dts | 34 +++++++++++++++++++ .../generic/base-files/etc/board.d/01_leds | 1 + .../generic/base-files/etc/board.d/02_network | 1 + target/linux/ath79/image/generic-ubnt.mk | 8 +++++ 4 files changed, 44 insertions(+) create mode 100644 target/linux/ath79/dts/ar9342_ubnt_powerbeam-m-xw.dts