@@ -53,6 +53,7 @@ xiaomi,mi-router-ac2100|\
xiaomi,redmi-router-ac2100)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x20000"
;;
+zyxel,lte3301-plus|\
zyxel,nr7101)
idx="$(find_mtd_index Config)"
[ -n "$idx" ] && \
new file mode 100644
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "zyxel,lte3301-plus", "mediatek,mt7621-soc";
+ model = "ZyXEL LTE3301-PLUS";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "white:power";
+ gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi {
+ label = "white:wifi";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ internet {
+ label = "white:internet";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+
+ usb {
+ label = "white:usb";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ };
+
+ lte {
+ label = "white:lte";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ };
+
+ mobile_green {
+ label = "green:mobile";
+ gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
+ };
+
+ mobile_orange {
+ label = "orange:mobile";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
+
+ mobile_red {
+ label = "red:mobile";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&gpio {
+ status = "okay";
+
+ lte_power {
+ gpio-hog;
+ gpios = <27 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "lte-power";
+ };
+
+ usb_power {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-power";
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Bootloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "Config";
+ reg = <0x80000 0x80000>;
+ };
+
+ factory: partition@100000 {
+ label = "Factory";
+ reg = <0x100000 0x40000>;
+ read-only;
+ };
+
+ partition@140000 {
+ /* reg = <0x140000 0x1ec0000>; */
+ reg = <0x140000 0x1ea0000>;
+ compatible = "openwrt,uimage", "denx,uimage", "openwrt,squashfs";
+ label = "firmware";
+ openwrt,offset = <380>;
+ openwrt,data-partition-name = "ubi";
+ };
+
+ partition@2140000 {
+ label = "Kernel2";
+ reg = <0x2140000 0x1ec0000>;
+ };
+
+ partition@4000000 {
+ label = "wwan";
+ reg = <0x4000000 0x100000>;
+ };
+
+ partition@4100000 {
+ label = "xxxxxdata";
+ reg = <0x4100000 0x1000000>;
+ };
+
+ partition@5100000 {
+ label = "rom-d";
+ reg = <0x5100000 0x100000>;
+ read-only;
+ };
+
+ partition@5200000 {
+ label = "reserve";
+ reg = <0x5200000 0x80000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+};
+
+&pcie0 {
+ status = "okay";
+
+ mt7615d@1,0 {
+ compatible = "pci14c3,7615";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,firmware-eeprom = "mt7615e_eeprom.bin";
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ mtd-mac-address = <&factory 0xfe6e>;
+ mtd-mac-address-increment = <1>;
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&factory 0xfe6e>;
+};
+
+&switch0 {
+ ports {
+ port@0 {
+ status = "okay";
+ label = "lan4";
+ };
+ port@1 {
+ status = "okay";
+ label = "lan3";
+ };
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+ port@3 {
+ status = "okay";
+ label = "lan1";
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "wdt", "uart3", "rgmii2", "jtag";
+ function = "gpio";
+ };
+};
\ No newline at end of file
@@ -1511,6 +1511,28 @@ define Device/zio_freezio
endef
TARGET_DEVICES += zio_freezio
+define Device/zyxel_lte3301-plus
+ $(Device/dsa-migration)
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := LTE3301-PLUS
+ DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
+ uboot-envtools kmod-usb-ledtrig-usbport kmod-usb-net-qmi-wwan \
+ kmod-usb-serial-option uqmi ubifs-utils ubi-utils fwtool
+ KERNEL := $(KERNEL_DTB) | uImage lzma
+ KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | \
+ zytrx-header $$(DEVICE_MODEL) 9.99(ABQU.1)$$(VERSION_DIST)-recovery
+ KERNEL_INITRAMFS_SUFFIX := -recovery.bin
+ IMAGES := sysupgrade.bin factory-ras.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs |\
+ zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION) | \
+ pad-to $$(BLOCKSIZE) | append-metadata
+ IMAGE/factory-ras.bin := append-kernel | append-rootfs |\
+ zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
+endef
+TARGET_DEVICES += zyxel_lte3301-plus
+
define Device/zyxel_nr7101
$(Device/dsa-migration)
BLOCKSIZE := 128k
@@ -98,6 +98,10 @@ xiaomi,redmi-router-ac2100)
youhua,wr1200js)
ucidef_set_led_netdev "internet" "INTERNET" "green:wan" "wan"
;;
+zyxel,lte3301-plus)
+ ucidef_set_led_netdev "internet" "internet" "white:internet" "wwan0"
+ ucidef_set_led_usbport "usb" "USB" "white:usb" "usb1-port2"
+ ;;
esac
board_config_flush
@@ -45,7 +45,8 @@ ramips_setup_interfaces()
ucidef_set_interface_lan "lan1 lan2"
;;
linksys,re6500|\
- netgear,wac104)
+ netgear,wac104|\
+ zyxel,lte3301-plus)
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
mikrotik,routerboard-750gr3)
@@ -22,6 +22,9 @@ ubnt,edgerouter-x-sfp)
ucidef_add_gpio_switch "poe_power_port3" "PoE Power Port3" "403"
ucidef_add_gpio_switch "poe_power_port4" "PoE Power Port4" "404"
;;
+zyxel,lte3301-plus)
+ ucidef_add_gpio_switch "lte_power" "Power LTE modem" "507"
+ ;;
zyxel,nr7101)
ucidef_add_gpio_switch "lte_reset" "Reset LTE/5G modem" "483"
;;
@@ -16,6 +16,7 @@ boot() {
samknows,whitebox-v8)
fw_setenv bootcount 0
;;
+ zyxel,lte3301-plus|\
zyxel,nr7101)
[ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 0x1
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
new file mode 100644
@@ -0,0 +1,43 @@
+. /lib/functions.sh
+
+lte3301plus_setup_ubi() {
+ if [ "$(cat /sys/firmware/devicetree/base/model)" != "ZyXEL LTE3301-PLUS" ]; then
+ return 0
+ fi
+ if [ -c /dev/ubi0 ]; then
+ return 0
+ fi
+
+ mtd=$(fgrep '"ubi"' /proc/mtd |cut -d: -f1)
+ if [ -z "$mtd" ]; then
+ echo "UBI mtd not found."
+ return 0
+ fi
+ mtd=/dev/$mtd
+
+ # If the kernel has not automounted the ubi volume, it must be initialized.
+ # The bootloader copies over images somehow different.
+ mtd erase $mtd
+ echo "Format $mtd with ubi."
+ if ! ubiformat -y $mtd; then
+ echo "Failed to format $mtd."
+ return 0
+ fi
+ echo "Attaching $mtd."
+ ubiattach -p $mtd
+
+ sleep 2
+ mknod /dev/ubi0 c 251 0
+ if ubinfo -a | grep rootfs_data >/dev/null 2>&1 ; then
+ echo "rootfs_data exists, no need."
+ return 0
+ fi
+
+ echo "Creating rootfs_data on ubi."
+ if ubimkvol /dev/ubi0 -n0 -N rootfs_data -m; then
+ mknod /dev/ubi0_0 c 251 1
+ fi
+ return 0
+}
+
+boot_hook_add preinit_main lte3301plus_setup_ubi
@@ -5,7 +5,7 @@
PART_NAME=firmware
REQUIRE_IMAGE_METADATA=1
-RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_BIN='fw_printenv fw_setenv ubinize mkfs.ubifs fwtool'
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
platform_check_image() {
@@ -82,6 +82,37 @@ platform_do_upgrade() {
ubnt,edgerouter-x-sfp)
platform_upgrade_ubnt_erx "$1"
;;
+ zyxel,lte3301-plus)
+ export IMG="$1"
+ fw_setenv CheckBypass 0
+ fw_setenv Image1Stable 0
+ mkdir -p /tmp/ubifs || reboot
+ [ -f /tmp/sysupgrade.tgz ] && cp /tmp/sysupgrade.tgz /tmp/ubifs/
+ mkfs.ubifs -d /tmp/ubifs -o /tmp/ubifs.img -v -m 2048 -e 124KiB -c20 -l2 || {
+ echo "Failed to generate image with ubifs."
+ reboot
+ }
+ rm -rf /tmp/ubifs
+ cat >/tmp/ubinize.ini <<EOF
+[rootfs_data]
+mode=ubi
+vol_id=0
+vol_type=dynamic
+vol_name=rootfs_data
+vol_flags=autoresize
+image=/tmp/ubifs.img
+EOF
+ ubinize -o /tmp/ubi-final.img -p 131072 -m 2048 -v /tmp/ubinize.ini || {
+ echo "Failed to generate image with ubinize."
+ reboot
+ }
+ rm -rf /tmp/ubifs.img
+ fwtool -i /dev/null -T "$IMG" >/dev/null || {
+ echo "Failed to dump image with fwtool."
+ reboot
+ }
+ (fwtool -i /dev/null -T "$IMG" ; cat /tmp/ubi-final.img) | mtd -r -e /dev/mtd3 write - /dev/mtd3
+ ;;
zyxel,nr7101)
fw_setenv CheckBypass 0
fw_setenv Image1Stable 0
The ZyXEL LTE3301-Plus is an 4G indoor CPE with 2 external LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7615E - Switch: 4 LAN ports (Gigabit) - LTE: Quectel EG506 connected by USB3 to SoC - SIM: 1 micro-SIM slot - USB: USB3 port - Buttons: Reset, WPS - LEDs: Multicolour power, internet, LTE, signal, Wifi, USB - Power: 12V, 1.5A The device is built as an indoor ethernet to LTE bridge or router with Wifi. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] 3.3V Vcc [o] RX [o] TX For more details about flashing and bootloader see commit 2449a632084b29632605e5a79ce5d73028eb15dd . Installation: 1. Upload image via web interface or via bootloader. 2. Wait for the device to come up. Signed-off-by: André Valentin <avalentin@marcant.net> --- package/boot/uboot-envtools/files/ramips | 1 + .../ramips/dts/mt7621_zyxel_lte3301-plus.dts | 209 ++++++++++++++++++ target/linux/ramips/image/mt7621.mk | 22 ++ .../mt7621/base-files/etc/board.d/01_leds | 4 + .../mt7621/base-files/etc/board.d/02_network | 3 +- .../base-files/etc/board.d/03_gpio_switches | 3 + .../mt7621/base-files/etc/init.d/bootcount | 1 + .../lib/preinit/79_lte3301-plus-setup-ubi | 43 ++++ .../mt7621/base-files/lib/upgrade/platform.sh | 33 ++- 9 files changed, 317 insertions(+), 2 deletions(-) create mode 100644 target/linux/ramips/dts/mt7621_zyxel_lte3301-plus.dts create mode 100644 target/linux/ramips/mt7621/base-files/lib/preinit/79_lte3301-plus-setup-ubi