@@ -40,6 +40,7 @@ ravpower,rp-wd03)
ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000"
;;
linksys,ea7300-v1|\
+linksys,ea7300-v2|\
linksys,ea7500-v2|\
xiaomi,mi-router-ac2100|\
xiaomi,mir3p|\
new file mode 100644
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621_linksys_ea7xxx.dtsi"
+
+/ {
+ compatible = "linksys,ea7300-v2", "mediatek,mt7621-soc";
+ model = "Linksys EA7300 v2";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wan_green {
+ label = "ea7300-v2:green:wan";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1_green {
+ label = "ea7300-v2:green:lan1";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2_green {
+ label = "ea7300-v2:green:lan2";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+
+ lan3_green {
+ label = "ea7300-v2:green:lan3";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ lan4_green {
+ label = "ea7300-v2:green:lan4";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power: power {
+ label = "ea7300-v2:white:power";
+ gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "ea7300-v2:green:wps";
+ gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
@@ -655,6 +655,15 @@ define Device/linksys_ea7300-v1
endef
TARGET_DEVICES += linksys_ea7300-v1
+define Device/linksys_ea7300-v2
+ $(Device/linksys_ea7xxx)
+ DEVICE_MODEL := EA7300
+ DEVICE_VARIANT := v2
+ LINKSYS_HWNAME := EA7300v2
+ DEVICE_PACKAGES += kmod-mt7603
+endef
+TARGET_DEVICES += linksys_ea7300-v2
+
define Device/linksys_ea7500-v2
$(Device/linksys_ea7xxx)
DEVICE_MODEL := EA7500
@@ -42,6 +42,7 @@ gnubee,gb-pc2)
ucidef_set_led_netdev "lan2" "lan2" "$boardname:green:lan2" "lan2"
;;
linksys,ea7300-v1|\
+linksys,ea7300-v2|\
linksys,ea7500-v2)
ucidef_set_led_netdev "lan1" "lan1 link" "$boardname:green:lan1" "lan1" "link"
ucidef_set_led_netdev "lan2" "lan2 link" "$boardname:green:lan2" "lan2" "link"
@@ -105,6 +105,7 @@ ramips_setup_macs()
label_mac=$wan_mac
;;
linksys,ea7300-v1|\
+ linksys,ea7300-v2|\
linksys,ea7500-v2)
lan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
wan_mac=$lan_mac
@@ -11,6 +11,7 @@ board=$(board_name)
case "$board" in
linksys,ea7300-v1|\
+ linksys,ea7300-v2|\
linksys,ea7500-v2)
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 1 > /sys${DEVPATH}/macaddress
@@ -9,6 +9,7 @@ boot() {
echo -e "bootcount\nbootchanged\n" | /usr/sbin/fw_setenv -s -
;;
linksys,ea7300-v1|\
+ linksys,ea7300-v2|\
linksys,ea7500-v2)
mtd resetbc s_env || true
;;
@@ -49,6 +49,7 @@ platform_do_upgrade() {
dlink,dir-2660-a1|\
hiwifi,hc5962|\
linksys,ea7300-v1|\
+ linksys,ea7300-v2|\
linksys,ea7500-v2|\
netgear,r6220|\
netgear,r6260|\
ramips: add support for Linksys EA7300 v2 This submission relied heavily on the work of Santiago Rodriguez-Papa <contact@rodsan.dev> Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. --- package/boot/uboot-envtools/files/ramips | 1 + .../ramips/dts/mt7621_linksys_ea7300-v2.dts | 55 +++++++++++++++++++ target/linux/ramips/image/mt7621.mk | 9 +++ .../mt7621/base-files/etc/board.d/01_leds | 1 + .../mt7621/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 1 + .../mt7621/base-files/etc/init.d/bootcount | 1 + .../mt7621/base-files/lib/upgrade/platform.sh | 1 + 8 files changed, 70 insertions(+) create mode 100644 target/linux/ramips/dts/mt7621_linksys_ea7300-v2.dts