diff mbox series

[OpenWrt-Devel] mvebu: add support for GL.iNet GL-MV1000

Message ID 1587105572-26571-1-git-send-email-li.zhang@gl-inet.com
State Accepted
Delegated to: Hauke Mehrtens
Headers show
Series [OpenWrt-Devel] mvebu: add support for GL.iNet GL-MV1000 | expand

Commit Message

Li Zhang April 17, 2020, 6:39 a.m. UTC
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
---
 package/boot/uboot-envtools/files/mvebu            |   3 +
 .../cortexa53/base-files/etc/board.d/02_network    |   3 +-
 .../arm64/boot/dts/marvell/armada-gl-mv1000.dts    | 165 +++++++++++++++++++++
 target/linux/mvebu/image/cortexa53.mk              |   9 ++
 4 files changed, 179 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
diff mbox series

Patch

diff --git a/package/boot/uboot-envtools/files/mvebu b/package/boot/uboot-envtools/files/mvebu
index 7902384..b883f0a 100644
--- a/package/boot/uboot-envtools/files/mvebu
+++ b/package/boot/uboot-envtools/files/mvebu
@@ -24,6 +24,9 @@  globalscale,espressobin-v7-emmc|\
 marvell,armada8040-mcbin)
 	ubootenv_add_uci_config "/dev/mtd0" "0x3f0000" "0x10000" "0x10000" "1"
 	;;
+glinet,gl-mv1000)
+	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x8000" "0x8000" "1"
+	;;
 linksys,caiman|\
 linksys,cobra|\
 linksys,shelby)
diff --git a/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
index ba4b930..9b1d97d 100755
--- a/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
@@ -14,7 +14,8 @@  case "$board" in
 globalscale,espressobin|\
 globalscale,espressobin-emmc|\
 globalscale,espressobin-v7|\
-globalscale,espressobin-v7-emmc)
+globalscale,espressobin-v7-emmc|\
+glinet,gl-mv1000)
 	ucidef_set_interfaces_lan_wan "lan0 lan1" "wan"
 	;;
 marvell,armada-3720-db|\
diff --git a/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts b/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
new file mode 100644
index 0000000..9d7963c
--- /dev/null
+++ b/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
@@ -0,0 +1,165 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for GL.iNet GL-MV1000
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	model = "GL.inet GL-MV1000";
+	compatible = "glinet,gl-mv1000", "marvell,armada3720";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	vcc_sd_reg1: regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vcc_sd1";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+        
+		gpios-states = <0>;
+		states = <1800000 0x1
+			3300000 0x0>;
+		enable-active-high;
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		m25p,fast-read;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0 0xf0000>;
+			};
+
+			partition@f0000 {
+				label = "u-boot-env";
+				reg = <0Xf0000 0x8000>;
+			};
+
+			factory: partition@f8000 {
+				label = "factory";
+				reg = <0xf8000 0x8000>;
+			};
+		};
+	};
+};
+
+&sdhci1 {
+	wp-inverted;
+	bus-width = <4>;
+	cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
+	marvell,pad-type = "sd";
+	no-1-8-v;
+	vqmmc-supply = <&vcc_sd_reg1>;
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	marvell,pad-type = "fixed-1-8v";
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&mdio {
+	switch0: switch0@1 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+
+		dsa,member = <0 0>;
+
+		ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&eth0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "wan";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan0";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan1";
+				phy-handle = <&switch0phy2>;
+			};
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0@11 {
+				reg = <0x11>;
+			};
+			switch0phy1: switch0phy1@12 {
+				reg = <0x12>;
+			};
+			switch0phy2: switch0phy2@13 {
+				reg = <0x13>;
+			};
+		};
+	};
+};
+
+&eth0 {
+	mtd-mac-address = <&factory 0x0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/target/linux/mvebu/image/cortexa53.mk b/target/linux/mvebu/image/cortexa53.mk
index 77f5c79..1436c1b 100644
--- a/target/linux/mvebu/image/cortexa53.mk
+++ b/target/linux/mvebu/image/cortexa53.mk
@@ -69,3 +69,12 @@  define Device/methode_udpu
   BOOT_SCRIPT := udpu
 endef
 TARGET_DEVICES += methode_udpu
+
+define Device/glinet_gl-mv1000
+  $(call Device/Default-arm64)
+  DEVICE_TITLE := GL.iNet GL-MV1000
+  DEVICE_DTS := armada-gl-mv1000
+  SUPPORTED_DEVICES := glinet,gl-mv1000
+endef
+TARGET_DEVICES += glinet_gl-mv1000
+