| Message ID | 20200911231619.2876486-1-olteanv@gmail.com |
|---|---|
| State | Changes Requested |
| Delegated to: | David Miller |
| Headers | show |
| Series | [net-next] net: bridge: pop vlan from skb if filtering is disabled but it's a pvid | expand |
On Sat, 2020-09-12 at 02:16 +0300, Vladimir Oltean wrote: > Currently the bridge untags VLANs from its VLAN group in > __allowed_ingress() only when VLAN filtering is enabled. > > When installing a pvid in egress-tagged mode, DSA switches have a > problem: > > ip link add dev br0 type bridge vlan_filtering 0 > ip link set swp0 master br0 > bridge vlan del dev swp0 vid 1 > bridge vlan add dev swp0 vid 1 pvid > > When adding a VLAN on a DSA switch interface, DSA configures the VLAN > membership of the CPU port using the same flags as swp0 (in this case > "pvid and not untagged"), in an attempt to copy the frame as-is from > ingress to the CPU. > > However, in this case, the packet may arrive untagged on ingress, it > will be pvid-tagged by the ingress port, and will be sent as > egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN > tag where there was none to speak of on ingress. > > When vlan_filtering is 1, this is not a problem, as stated in the first > paragraph, because __allowed_ingress() will pop it. But currently, when > vlan_filtering is 0 and we have such a VLAN configuration, we need an > 8021q upper (br0.1) to be able to ping over that VLAN. > > Make the 2 cases (vlan_filtering 0 and 1) behave the same way by popping > the pvid, if the skb happens to be tagged with it, when vlan_filtering > is 0. > > There was an attempt to resolve this issue locally within the DSA > receive data path, but even though we can determine that we are under a > bridge with vlan_filtering=0, there are still some challenges: > - we cannot be certain that the skb will end up in the software bridge's > data path, and for that reason, we may be popping the VLAN for > nothing. Example: there might exist an 8021q upper with the same VLAN, > or this interface might be a DSA master for another switch. In that > case, the VLAN should definitely not be popped even if it is equal to > the default_pvid of the bridge, because it will be consumed about the > DSA layer below. Could you point me to a thread where these problems were discussed and why they couldn't be resolved within DSA in detail ? > - the bridge API only offers a race-free API for determining the pvid of > a port, br_vlan_get_pvid(), under RTNL. > The API can be easily extended. > And in fact this might not even be a situation unique to DSA. Any driver > that receives untagged frames as pvid-tagged is now able to communicate > without needing an 8021q upper for the pvid. > I would prefer we don't add hardware/driver-specific fixes in the bridge, when vlan filtering is disabled there should be no vlan manipulation/filtering done by the bridge. This could potentially break users who have added 8021q devices as bridge ports. At the very least this needs to be hidden behind a new option, but I would like to find a way to actually push it back to DSA. But again adding hardware/driver-specific options should be avoided. Can you use tc to pop the vlan on ingress ? I mean the cases above are visible to the user, so they might decide to add the ingress vlan rule. Thanks, Nik > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > Tested-by: Florian Fainelli <f.fainelli@gmail.com> > --- > net/bridge/br_vlan.c | 16 ++++++++++++++++ > 1 file changed, 16 insertions(+) > > diff --git a/net/bridge/br_vlan.c b/net/bridge/br_vlan.c > index d2b8737f9fc0..ecfdb9cd3183 100644 > --- a/net/bridge/br_vlan.c > +++ b/net/bridge/br_vlan.c > @@ -580,7 +580,23 @@ bool br_allowed_ingress(const struct net_bridge *br, > * permitted. > */ > if (!br_opt_get(br, BROPT_VLAN_ENABLED)) { > + u16 v; > + > BR_INPUT_SKB_CB(skb)->vlan_filtered = false; > + > + /* See comment in __allowed_ingress about how skb can end up > + * here not having a hwaccel tag > + */ > + if (unlikely(!skb_vlan_tag_present(skb) && > + skb->protocol == br->vlan_proto)) { > + skb = skb_vlan_untag(skb); > + if (unlikely(!skb)) > + return false; > + } > + > + if (!br_vlan_get_tag(skb, &v) && v == br_get_pvid(vg)) > + __vlan_hwaccel_clear_tag(skb); > + > return true; > } >
On Sat, Sep 12, 2020 at 06:56:12AM +0000, Nikolay Aleksandrov wrote: > Could you point me to a thread where these problems were discussed and why > they couldn't be resolved within DSA in detail ? See my discussion with Florian in this thread: http://patchwork.ozlabs.org/project/netdev/patch/20200907182910.1285496-5-olteanv@gmail.com/ There's a bunch of unrelated stuff going on there, hope you'll manage. > > - the bridge API only offers a race-free API for determining the pvid of > > a port, br_vlan_get_pvid(), under RTNL. > > > > The API can be easily extended. > If you can help, cool. > > And in fact this might not even be a situation unique to DSA. Any driver > > that receives untagged frames as pvid-tagged is now able to communicate > > without needing an 8021q upper for the pvid. > > > > I would prefer we don't add hardware/driver-specific fixes in the bridge, when > vlan filtering is disabled there should be no vlan manipulation/filtering done > by the bridge. This could potentially break users who have added 8021q devices > as bridge ports. At the very least this needs to be hidden behind a new option, > but I would like to find a way to actually push it back to DSA. But again adding > hardware/driver-specific options should be avoided. > > Can you use tc to pop the vlan on ingress ? I mean the cases above are visible > to the user, so they might decide to add the ingress vlan rule. > > Thanks, > Nik I can, but I think that all in all it's a bit strange for the bridge to not untag pvid-tagged frames. Thanks! -Vladimir
On Sat, 2020-09-12 at 10:23 +0300, Vladimir Oltean wrote: > On Sat, Sep 12, 2020 at 06:56:12AM +0000, Nikolay Aleksandrov wrote: > > Could you point me to a thread where these problems were discussed and why > > they couldn't be resolved within DSA in detail ? > > See my discussion with Florian in this thread: > http://patchwork.ozlabs.org/project/netdev/patch/20200907182910.1285496-5-olteanv@gmail.com/ > There's a bunch of unrelated stuff going on there, hope you'll manage. > Thanks! I'm traveling and will be back on Sun evening, will go through the thread then. > > > - the bridge API only offers a race-free API for determining the pvid of > > > a port, br_vlan_get_pvid(), under RTNL. > > > > > > > The API can be easily extended. > > > > If you can help, cool. > > > > And in fact this might not even be a situation unique to DSA. Any driver > > > that receives untagged frames as pvid-tagged is now able to communicate > > > without needing an 8021q upper for the pvid. > > > > > > > I would prefer we don't add hardware/driver-specific fixes in the bridge, when > > vlan filtering is disabled there should be no vlan manipulation/filtering done > > by the bridge. This could potentially break users who have added 8021q devices > > as bridge ports. At the very least this needs to be hidden behind a new option, > > but I would like to find a way to actually push it back to DSA. But again adding > > hardware/driver-specific options should be avoided. > > > > Can you use tc to pop the vlan on ingress ? I mean the cases above are visible > > to the user, so they might decide to add the ingress vlan rule. > > > > Thanks, > > Nik > > I can, but I think that all in all it's a bit strange for the bridge to > not untag pvid-tagged frames. > > Thanks! > -Vladimir If vlan filtering is disabled the bridge shouldn't do any vlan processing, that's the expected behaviour. If tc is a viable option then I'd explore that further and avoid adding more code.
On Sat, Sep 12, 2020 at 07:37:42AM +0000, Nikolay Aleksandrov wrote: > On Sat, 2020-09-12 at 10:23 +0300, Vladimir Oltean wrote: > > On Sat, Sep 12, 2020 at 06:56:12AM +0000, Nikolay Aleksandrov wrote: > > > Could you point me to a thread where these problems were discussed and why > > > they couldn't be resolved within DSA in detail ? > > > > See my discussion with Florian in this thread: > > http://patchwork.ozlabs.org/project/netdev/patch/20200907182910.1285496-5-olteanv@gmail.com/ > > There's a bunch of unrelated stuff going on there, hope you'll manage. > > > > Thanks! > I'm traveling and will be back on Sun evening, will go through the thread then. > Ok, take your time. For some reason patchwork seems to have trimmed the discussion thread. See on lore here: https://lore.kernel.org/netdev/20200907182910.1285496-5-olteanv@gmail.com/T/#t Thanks, -Vladimir
On 9/11/2020 11:56 PM, Nikolay Aleksandrov wrote: > On Sat, 2020-09-12 at 02:16 +0300, Vladimir Oltean wrote: >> Currently the bridge untags VLANs from its VLAN group in >> __allowed_ingress() only when VLAN filtering is enabled. >> >> When installing a pvid in egress-tagged mode, DSA switches have a >> problem: >> >> ip link add dev br0 type bridge vlan_filtering 0 >> ip link set swp0 master br0 >> bridge vlan del dev swp0 vid 1 >> bridge vlan add dev swp0 vid 1 pvid >> >> When adding a VLAN on a DSA switch interface, DSA configures the VLAN >> membership of the CPU port using the same flags as swp0 (in this case >> "pvid and not untagged"), in an attempt to copy the frame as-is from >> ingress to the CPU. >> >> However, in this case, the packet may arrive untagged on ingress, it >> will be pvid-tagged by the ingress port, and will be sent as >> egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN >> tag where there was none to speak of on ingress. >> >> When vlan_filtering is 1, this is not a problem, as stated in the first >> paragraph, because __allowed_ingress() will pop it. But currently, when >> vlan_filtering is 0 and we have such a VLAN configuration, we need an >> 8021q upper (br0.1) to be able to ping over that VLAN. >> >> Make the 2 cases (vlan_filtering 0 and 1) behave the same way by popping >> the pvid, if the skb happens to be tagged with it, when vlan_filtering >> is 0. >> >> There was an attempt to resolve this issue locally within the DSA >> receive data path, but even though we can determine that we are under a >> bridge with vlan_filtering=0, there are still some challenges: >> - we cannot be certain that the skb will end up in the software bridge's >> data path, and for that reason, we may be popping the VLAN for >> nothing. Example: there might exist an 8021q upper with the same VLAN, >> or this interface might be a DSA master for another switch. In that >> case, the VLAN should definitely not be popped even if it is equal to >> the default_pvid of the bridge, because it will be consumed about the >> DSA layer below. > > Could you point me to a thread where these problems were discussed and why > they couldn't be resolved within DSA in detail ? > >> - the bridge API only offers a race-free API for determining the pvid of >> a port, br_vlan_get_pvid(), under RTNL. >> > > The API can be easily extended. > >> And in fact this might not even be a situation unique to DSA. Any driver >> that receives untagged frames as pvid-tagged is now able to communicate >> without needing an 8021q upper for the pvid. >> > > I would prefer we don't add hardware/driver-specific fixes in the bridge, when > vlan filtering is disabled there should be no vlan manipulation/filtering done > by the bridge. This could potentially break users who have added 8021q devices > as bridge ports. At the very least this needs to be hidden behind a new option, > but I would like to find a way to actually push it back to DSA. But again adding > hardware/driver-specific options should be avoided. > > Can you use tc to pop the vlan on ingress ? I mean the cases above are visible > to the user, so they might decide to add the ingress vlan rule. We had discussed various options with Vladimir in the threads he points out but this one is by far the cleanest and basically aligns the data path when the bridge is configured with vlan_filtering=0 or 1. Some Ethernet switches supported via DSA either insist on or the driver has been written in such a way that the default_pvid of the bridge which is egress untagged for the user-facing ports is configured as egress tagged for the CPU port. That CPU port is ultimately responsible for bringing the Ethernet frames into the Linux host and the bridge data path which is how we got VLAN tagged frames into the bridge, even if a vlan_filtering=0 bridge is not supposed to. We can solve this today by having a 802.1Q upper on top of the bridge default to pop/push the default_pvid VLAN tag, but this is not obvious, represents a divergence from a pure software bridge, and leads to support questions. What is also utterly confusing for instance is that a raw socket like one opened by a DHCP client will successfully allow br0 to obtain an IP address, but the data path still is not functional, as you would need to use br0.1 to have a working data path taking care of the VLAN tag. Vladimir had offered a DSA centric solution to this problem, which was not that bad after all, but this one is also my favorite. Let us know when you are caught up on the thread and we can see how to solve that the best way.
On Sat, 2020-09-12 at 12:38 -0700, Florian Fainelli wrote: > > On 9/11/2020 11:56 PM, Nikolay Aleksandrov wrote: > > On Sat, 2020-09-12 at 02:16 +0300, Vladimir Oltean wrote: > > > Currently the bridge untags VLANs from its VLAN group in > > > __allowed_ingress() only when VLAN filtering is enabled. > > > > > > When installing a pvid in egress-tagged mode, DSA switches have a > > > problem: > > > > > > ip link add dev br0 type bridge vlan_filtering 0 > > > ip link set swp0 master br0 > > > bridge vlan del dev swp0 vid 1 > > > bridge vlan add dev swp0 vid 1 pvid > > > > > > When adding a VLAN on a DSA switch interface, DSA configures the VLAN > > > membership of the CPU port using the same flags as swp0 (in this case > > > "pvid and not untagged"), in an attempt to copy the frame as-is from > > > ingress to the CPU. > > > > > > However, in this case, the packet may arrive untagged on ingress, it > > > will be pvid-tagged by the ingress port, and will be sent as > > > egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN > > > tag where there was none to speak of on ingress. > > > > > > When vlan_filtering is 1, this is not a problem, as stated in the first > > > paragraph, because __allowed_ingress() will pop it. But currently, when > > > vlan_filtering is 0 and we have such a VLAN configuration, we need an > > > 8021q upper (br0.1) to be able to ping over that VLAN. > > > > > > Make the 2 cases (vlan_filtering 0 and 1) behave the same way by popping > > > the pvid, if the skb happens to be tagged with it, when vlan_filtering > > > is 0. > > > > > > There was an attempt to resolve this issue locally within the DSA > > > receive data path, but even though we can determine that we are under a > > > bridge with vlan_filtering=0, there are still some challenges: > > > - we cannot be certain that the skb will end up in the software bridge's > > > data path, and for that reason, we may be popping the VLAN for > > > nothing. Example: there might exist an 8021q upper with the same VLAN, > > > or this interface might be a DSA master for another switch. In that > > > case, the VLAN should definitely not be popped even if it is equal to > > > the default_pvid of the bridge, because it will be consumed about the > > > DSA layer below. > > > > Could you point me to a thread where these problems were discussed and why > > they couldn't be resolved within DSA in detail ? > > > > > - the bridge API only offers a race-free API for determining the pvid of > > > a port, br_vlan_get_pvid(), under RTNL. > > > > > > > The API can be easily extended. > > > > > And in fact this might not even be a situation unique to DSA. Any driver > > > that receives untagged frames as pvid-tagged is now able to communicate > > > without needing an 8021q upper for the pvid. > > > > > > > I would prefer we don't add hardware/driver-specific fixes in the bridge, when > > vlan filtering is disabled there should be no vlan manipulation/filtering done > > by the bridge. This could potentially break users who have added 8021q devices > > as bridge ports. At the very least this needs to be hidden behind a new option, > > but I would like to find a way to actually push it back to DSA. But again adding > > hardware/driver-specific options should be avoided. > > > > Can you use tc to pop the vlan on ingress ? I mean the cases above are visible > > to the user, so they might decide to add the ingress vlan rule. > > We had discussed various options with Vladimir in the threads he points > out but this one is by far the cleanest and basically aligns the data > path when the bridge is configured with vlan_filtering=0 or 1. > > Some Ethernet switches supported via DSA either insist on or the driver > has been written in such a way that the default_pvid of the bridge which > is egress untagged for the user-facing ports is configured as egress > tagged for the CPU port. That CPU port is ultimately responsible for > bringing the Ethernet frames into the Linux host and the bridge data > path which is how we got VLAN tagged frames into the bridge, even if a > vlan_filtering=0 bridge is not supposed to. > I read the thread and see your problem, but I still think that it must not be fixed in the bridge device, more below. > We can solve this today by having a 802.1Q upper on top of the bridge > default to pop/push the default_pvid VLAN tag, but this is not obvious, > represents a divergence from a pure software bridge, and leads to > support questions. What is also utterly confusing for instance is that a > raw socket like one opened by a DHCP client will successfully allow br0 > to obtain an IP address, but the data path still is not functional, as > you would need to use br0.1 to have a working data path taking care of > the VLAN tag. > With this patch br0.1 won't work anymore for anyone having vlan_filtering=0. > Vladimir had offered a DSA centric solution to this problem, which was > not that bad after all, but this one is also my favorite. > I saw it, and it looks good. I saw the one of the main issues is not having an RCU get pvid helper. I can provide you with that to simplify the patch. > Let us know when you are caught up on the thread and we can see how to > solve that the best way. I'll start with why this patch is a non-starter, I'm guessing most of us already have guessed, but just to have them: - the fix is DSA-specific, it must not reside in the bridge - vlan_filtering=0 means absolutely no vlan processing, that is what everyone expects and breaking that expectation would break various use cases Less important, but still: - it is in the fast path for everyone - it can already be fixed by a tc action/8021q device We can go into details but that would be a waste of time, instead I think we should focus on Vladimir's proposed DSA change. Vladimir, I think with the right pvid helper the patch would reduce to dsa_untag_bridge_pvid() on the Rx path only. One thing that I'm curious about is shouldn't dsa_untag_bridge_pvid() check if the bridge pvid is == to the skb tag and the port's pvid? Since we can have the port's pvid different from the bridge's. That's for the case of vlan_filtering=1 and the port having that vlan, but not as pvid. Thanks, Nik
On 9/14/2020 12:51 AM, Nikolay Aleksandrov wrote: > On Sat, 2020-09-12 at 12:38 -0700, Florian Fainelli wrote: >> >> On 9/11/2020 11:56 PM, Nikolay Aleksandrov wrote: >>> On Sat, 2020-09-12 at 02:16 +0300, Vladimir Oltean wrote: >>>> Currently the bridge untags VLANs from its VLAN group in >>>> __allowed_ingress() only when VLAN filtering is enabled. >>>> >>>> When installing a pvid in egress-tagged mode, DSA switches have a >>>> problem: >>>> >>>> ip link add dev br0 type bridge vlan_filtering 0 >>>> ip link set swp0 master br0 >>>> bridge vlan del dev swp0 vid 1 >>>> bridge vlan add dev swp0 vid 1 pvid >>>> >>>> When adding a VLAN on a DSA switch interface, DSA configures the VLAN >>>> membership of the CPU port using the same flags as swp0 (in this case >>>> "pvid and not untagged"), in an attempt to copy the frame as-is from >>>> ingress to the CPU. >>>> >>>> However, in this case, the packet may arrive untagged on ingress, it >>>> will be pvid-tagged by the ingress port, and will be sent as >>>> egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN >>>> tag where there was none to speak of on ingress. >>>> >>>> When vlan_filtering is 1, this is not a problem, as stated in the first >>>> paragraph, because __allowed_ingress() will pop it. But currently, when >>>> vlan_filtering is 0 and we have such a VLAN configuration, we need an >>>> 8021q upper (br0.1) to be able to ping over that VLAN. >>>> >>>> Make the 2 cases (vlan_filtering 0 and 1) behave the same way by popping >>>> the pvid, if the skb happens to be tagged with it, when vlan_filtering >>>> is 0. >>>> >>>> There was an attempt to resolve this issue locally within the DSA >>>> receive data path, but even though we can determine that we are under a >>>> bridge with vlan_filtering=0, there are still some challenges: >>>> - we cannot be certain that the skb will end up in the software bridge's >>>> data path, and for that reason, we may be popping the VLAN for >>>> nothing. Example: there might exist an 8021q upper with the same VLAN, >>>> or this interface might be a DSA master for another switch. In that >>>> case, the VLAN should definitely not be popped even if it is equal to >>>> the default_pvid of the bridge, because it will be consumed about the >>>> DSA layer below. >>> >>> Could you point me to a thread where these problems were discussed and why >>> they couldn't be resolved within DSA in detail ? >>> >>>> - the bridge API only offers a race-free API for determining the pvid of >>>> a port, br_vlan_get_pvid(), under RTNL. >>>> >>> >>> The API can be easily extended. >>> >>>> And in fact this might not even be a situation unique to DSA. Any driver >>>> that receives untagged frames as pvid-tagged is now able to communicate >>>> without needing an 8021q upper for the pvid. >>>> >>> >>> I would prefer we don't add hardware/driver-specific fixes in the bridge, when >>> vlan filtering is disabled there should be no vlan manipulation/filtering done >>> by the bridge. This could potentially break users who have added 8021q devices >>> as bridge ports. At the very least this needs to be hidden behind a new option, >>> but I would like to find a way to actually push it back to DSA. But again adding >>> hardware/driver-specific options should be avoided. >>> >>> Can you use tc to pop the vlan on ingress ? I mean the cases above are visible >>> to the user, so they might decide to add the ingress vlan rule. >> >> We had discussed various options with Vladimir in the threads he points >> out but this one is by far the cleanest and basically aligns the data >> path when the bridge is configured with vlan_filtering=0 or 1. >> >> Some Ethernet switches supported via DSA either insist on or the driver >> has been written in such a way that the default_pvid of the bridge which >> is egress untagged for the user-facing ports is configured as egress >> tagged for the CPU port. That CPU port is ultimately responsible for >> bringing the Ethernet frames into the Linux host and the bridge data >> path which is how we got VLAN tagged frames into the bridge, even if a >> vlan_filtering=0 bridge is not supposed to. >> > > I read the thread and see your problem, but I still think that it must not be > fixed in the bridge device, more below. > >> We can solve this today by having a 802.1Q upper on top of the bridge >> default to pop/push the default_pvid VLAN tag, but this is not obvious, >> represents a divergence from a pure software bridge, and leads to >> support questions. What is also utterly confusing for instance is that a >> raw socket like one opened by a DHCP client will successfully allow br0 >> to obtain an IP address, but the data path still is not functional, as >> you would need to use br0.1 to have a working data path taking care of >> the VLAN tag. >> > > With this patch br0.1 won't work anymore for anyone having vlan_filtering=0. > >> Vladimir had offered a DSA centric solution to this problem, which was >> not that bad after all, but this one is also my favorite. >> > > I saw it, and it looks good. I saw the one of the main issues is not having an > RCU get pvid helper. I can provide you with that to simplify the patch. > >> Let us know when you are caught up on the thread and we can see how to >> solve that the best way. > > I'll start with why this patch is a non-starter, I'm guessing most of us already > have guessed, but just to have them: > - the fix is DSA-specific, it must not reside in the bridge Not necessarily any switch that forces egress tagging of a given PVID would fall in that category. > - vlan_filtering=0 means absolutely no vlan processing, that is what everyone > expects and breaking that expectation would break various use cases OK > > Less important, but still: > - it is in the fast path for everyone > - it can already be fixed by a tc action/8021q device Sure, but the point is that it should be fixed in a way that is transparent to the user, as much as possible. > > We can go into details but that would be a waste of time, instead I think we > should focus on Vladimir's proposed DSA change. > > Vladimir, I think with the right pvid helper the patch would reduce to > dsa_untag_bridge_pvid() on the Rx path only. One thing that I'm curious about > is shouldn't dsa_untag_bridge_pvid() check if the bridge pvid is == to the skb > tag and the port's pvid? > Since we can have the port's pvid different from the bridge's. That's for the > case of vlan_filtering=1 and the port having that vlan, but not as pvid. > > Thanks, > Nik >
On 9/14/20 1:11 PM, Florian Fainelli wrote: >> Less important, but still: >> - it is in the fast path for everyone >> - it can already be fixed by a tc action/8021q device > > Sure, but the point is that it should be fixed in a way that is > transparent to the user, as much as possible. > >> >> We can go into details but that would be a waste of time, instead I >> think we >> should focus on Vladimir's proposed DSA change. >> >> Vladimir, I think with the right pvid helper the patch would reduce to >> dsa_untag_bridge_pvid() on the Rx path only. One thing that I'm >> curious about >> is shouldn't dsa_untag_bridge_pvid() check if the bridge pvid is == to >> the skb >> tag and the port's pvid? >> Since we can have the port's pvid different from the bridge's. That's >> for the >> case of vlan_filtering=1 and the port having that vlan, but not as pvid. Vladimir, let me know if you have a patch for DSA and I can give it a try quickly. Thanks!
On Mon, Sep 21, 2020 at 12:44:43PM -0700, Florian Fainelli wrote: > Vladimir, let me know if you have a patch for DSA and I can give it a > try quickly. Thanks! Let me clean it up a little and send it, I need to export a wrapper over br_get_pvid() for external use, called under rcu_read_lock().
On Mon, Sep 21, 2020 at 10:56:07PM +0300, Vladimir Oltean wrote: > On Mon, Sep 21, 2020 at 12:44:43PM -0700, Florian Fainelli wrote: > > Vladimir, let me know if you have a patch for DSA and I can give it a > > try quickly. Thanks! > > Let me clean it up a little and send it, I need to export a wrapper over > br_get_pvid() for external use, called under rcu_read_lock(). Here it is as an attached patch, sorry that it can't be simpler than that. Please call the function from where you need it, and then submit it yourself to net-next. Also, you'll notice a lockdep warning when you test it. That's what the br_vlan_get_pvid_rcu() fix I've just sent is for. Make sure you also take that. Thanks, -Vladimir
diff --git a/net/bridge/br_vlan.c b/net/bridge/br_vlan.c index d2b8737f9fc0..ecfdb9cd3183 100644 --- a/net/bridge/br_vlan.c +++ b/net/bridge/br_vlan.c @@ -580,7 +580,23 @@ bool br_allowed_ingress(const struct net_bridge *br, * permitted. */ if (!br_opt_get(br, BROPT_VLAN_ENABLED)) { + u16 v; + BR_INPUT_SKB_CB(skb)->vlan_filtered = false; + + /* See comment in __allowed_ingress about how skb can end up + * here not having a hwaccel tag + */ + if (unlikely(!skb_vlan_tag_present(skb) && + skb->protocol == br->vlan_proto)) { + skb = skb_vlan_untag(skb); + if (unlikely(!skb)) + return false; + } + + if (!br_vlan_get_tag(skb, &v) && v == br_get_pvid(vg)) + __vlan_hwaccel_clear_tag(skb); + return true; }