| Message ID | fc7440a2f4bf9ab95e47a911c0e0b3b6a2250356.1386108712.git.stefan@agner.ch |
|---|---|
| State | Superseded, archived |
| Delegated to: | Stephen Warren |
| Headers | show |
Am Dienstag, den 03.12.2013, 23:18 +0100 schrieb Stefan Agner: > Set the parent of the regulators LDO2 to LDO9 according to the > schematic. Set the base voltage to 3.3V, there is only 3.3V on the > module itself. > > Set the Core and CPU voltage to the specified voltages of 1.2V and > 1.0V respectivly. > > LDO6 should deliver 2.85V. The attached peripherals were not in > use so far. > > Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > --- > arch/arm/boot/dts/tegra20-colibri-512.dtsi | 30 +++++++++++++++--------------- > 1 file changed, 15 insertions(+), 15 deletions(-) > > diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi > index cbe89ff..51e0880 100644 > --- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi > +++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi > @@ -225,15 +225,15 @@ > #gpio-cells = <2>; > gpio-controller; > > - sys-supply = <&vdd_5v0_reg>; > + sys-supply = <&vdd_3v3_reg>; > vin-sm0-supply = <&sys_reg>; > vin-sm1-supply = <&sys_reg>; > vin-sm2-supply = <&sys_reg>; > vinldo01-supply = <&sm2_reg>; > - vinldo23-supply = <&sm2_reg>; > - vinldo4-supply = <&sm2_reg>; > - vinldo678-supply = <&sm2_reg>; > - vinldo9-supply = <&sm2_reg>; > + vinldo23-supply = <&vdd_3v3_reg>; > + vinldo4-supply = <&vdd_3v3_reg>; > + vinldo678-supply = <&vdd_3v3_reg>; > + vinldo9-supply = <&vdd_3v3_reg>; > > regulators { > #address-cells = <1>; > @@ -250,8 +250,8 @@ > reg = <1>; > regulator-compatible = "sm0"; > regulator-name = "vdd_sm0,vdd_core"; > - regulator-min-microvolt = <1275000>; > - regulator-max-microvolt = <1275000>; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > regulator-always-on; > }; > > @@ -259,8 +259,8 @@ > reg = <2>; > regulator-compatible = "sm1"; > regulator-name = "vdd_sm1,vdd_cpu"; > - regulator-min-microvolt = <1100000>; > - regulator-max-microvolt = <1100000>; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > regulator-always-on; > }; > > @@ -316,8 +316,8 @@ > reg = <10>; > regulator-compatible = "ldo6"; > regulator-name = "vdd_ldo6,avdd_vdac,vddio_vi,vddio_cam"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > }; > > hdmi_vdd_reg: regulator@11 { > @@ -504,12 +504,12 @@ > #address-cells = <1>; > #size-cells = <0>; > > - vdd_5v0_reg: regulator@100 { > + vdd_3v3_reg: regulator@100 { > compatible = "regulator-fixed"; > reg = <100>; > - regulator-name = "vdd_5v0"; > - regulator-min-microvolt = <5000000>; > - regulator-max-microvolt = <5000000>; > + regulator-name = "vdd_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > regulator-always-on; > }; >
On 12/03/2013 03:18 PM, Stefan Agner wrote: > Set the parent of the regulators LDO2 to LDO9 according to the > schematic. Set the base voltage to 3.3V, there is only 3.3V on the > module itself. > > Set the Core and CPU voltage to the specified voltages of 1.2V and > 1.0V respectivly. > > LDO6 should deliver 2.85V. The attached peripherals were not in > use so far. Does this depend on patch 1/3 or 2/3, or can I apply it to the Tegra tree which doesn't include those patches? If this does depend on patch 1/3 or 2/3... this patch feels a bit big to apply to the MFD tree. Perhaps patch 1/3 and 2/3 could be applied alone to a topic branch in the MFD tree so I can merge that into the Tegra tree in order to apply this? -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Am 2013-12-05 18:12, schrieb Stephen Warren: > On 12/03/2013 03:18 PM, Stefan Agner wrote: >> Set the parent of the regulators LDO2 to LDO9 according to the >> schematic. Set the base voltage to 3.3V, there is only 3.3V on the >> module itself. >> >> Set the Core and CPU voltage to the specified voltages of 1.2V and >> 1.0V respectivly. >> >> LDO6 should deliver 2.85V. The attached peripherals were not in >> use so far. > > Does this depend on patch 1/3 or 2/3, or can I apply it to the Tegra > tree which doesn't include those patches? This patch is independent from 1/3 and 2/3, so you can apply it to the Tegra tree. The relevant DT change for 2/3 is included in 2/3... -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi index cbe89ff..51e0880 100644 --- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi +++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi @@ -225,15 +225,15 @@ #gpio-cells = <2>; gpio-controller; - sys-supply = <&vdd_5v0_reg>; + sys-supply = <&vdd_3v3_reg>; vin-sm0-supply = <&sys_reg>; vin-sm1-supply = <&sys_reg>; vin-sm2-supply = <&sys_reg>; vinldo01-supply = <&sm2_reg>; - vinldo23-supply = <&sm2_reg>; - vinldo4-supply = <&sm2_reg>; - vinldo678-supply = <&sm2_reg>; - vinldo9-supply = <&sm2_reg>; + vinldo23-supply = <&vdd_3v3_reg>; + vinldo4-supply = <&vdd_3v3_reg>; + vinldo678-supply = <&vdd_3v3_reg>; + vinldo9-supply = <&vdd_3v3_reg>; regulators { #address-cells = <1>; @@ -250,8 +250,8 @@ reg = <1>; regulator-compatible = "sm0"; regulator-name = "vdd_sm0,vdd_core"; - regulator-min-microvolt = <1275000>; - regulator-max-microvolt = <1275000>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; regulator-always-on; }; @@ -259,8 +259,8 @@ reg = <2>; regulator-compatible = "sm1"; regulator-name = "vdd_sm1,vdd_cpu"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; regulator-always-on; }; @@ -316,8 +316,8 @@ reg = <10>; regulator-compatible = "ldo6"; regulator-name = "vdd_ldo6,avdd_vdac,vddio_vi,vddio_cam"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; }; hdmi_vdd_reg: regulator@11 { @@ -504,12 +504,12 @@ #address-cells = <1>; #size-cells = <0>; - vdd_5v0_reg: regulator@100 { + vdd_3v3_reg: regulator@100 { compatible = "regulator-fixed"; reg = <100>; - regulator-name = "vdd_5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; };
Set the parent of the regulators LDO2 to LDO9 according to the schematic. Set the base voltage to 3.3V, there is only 3.3V on the module itself. Set the Core and CPU voltage to the specified voltages of 1.2V and 1.0V respectivly. LDO6 should deliver 2.85V. The attached peripherals were not in use so far. Signed-off-by: Stefan Agner <stefan@agner.ch> --- arch/arm/boot/dts/tegra20-colibri-512.dtsi | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-)