diff mbox series

[v3,3/3] hwmon: (adt7475) Add support for configuring initial PWM state

Message ID 20240520030321.3756604-4-chris.packham@alliedtelesis.co.nz
State Superseded
Headers show
Series hwmon: (adt7475) duty cycle configuration | expand

Commit Message

Chris Packham May 20, 2024, 3:03 a.m. UTC
By default the PWM duty cycle in hardware is 100%. On some systems this
can cause unwanted fan noise. Add the ability to specify the fan
connections and initial state of the PWMs via device properties.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---

Notes:
    Changes in v3:
    - Use the pwm provider/consumer bindings
    Changes in v2:
    - Use correct device property string for frequency
    - Allow -EINVAL and only warn on error
    - Use a frequency of 0 to indicate that the hardware should be left as-is

 drivers/hwmon/adt7475.c | 63 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 63 insertions(+)
diff mbox series

Patch

diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
index 4224ffb30483..2b8f39c1d76f 100644
--- a/drivers/hwmon/adt7475.c
+++ b/drivers/hwmon/adt7475.c
@@ -21,6 +21,8 @@ 
 #include <linux/of.h>
 #include <linux/util_macros.h>
 
+#include <dt-bindings/pwm/pwm.h>
+
 /* Indexes for the sysfs hooks */
 
 #define INPUT		0
@@ -1662,6 +1664,63 @@  static int adt7475_set_pwm_polarity(struct i2c_client *client)
 	return 0;
 }
 
+static int adt7475_fan_pwm_config(struct i2c_client *client)
+{
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	struct fwnode_handle *child;
+	struct of_phandle_args args = {};
+	int ret, pwm, duty, freq, flags;
+	u8 val;
+
+	device_for_each_child_node(&client->dev, child) {
+		if (!is_of_node(child))
+			continue;
+
+		ret = of_parse_phandle_with_args(to_of_node(child), "pwms", "#pwm-cells", 0, &args);
+		if (ret)
+			return ret;
+
+		if (args.args_count != 4)
+			return -EINVAL;
+
+		pwm = args.args[0];
+		freq = find_closest(args.args[1], pwmfreq_table, ARRAY_SIZE(pwmfreq_table));
+		flags = args.args[2];
+		duty = clamp_val(args.args[3], 0, 0xFF);
+
+		if (pwm >= ADT7475_PWM_COUNT)
+			return -EINVAL;
+
+		ret = adt7475_read(PWM_CONFIG_REG(pwm));
+		if (ret < 0)
+			return ret;
+		val = ret;
+		if (flags & PWM_POLARITY_INVERTED)
+			val |= BIT(4);
+		else
+			val &= ~BIT(4);
+
+		ret = i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(pwm), val);
+		if (ret)
+			return ret;
+
+		data->pwm[pwm][0] = duty;
+		ret = i2c_smbus_write_byte_data(client, PWM_REG(pwm), data->pwm[pwm][0]);
+		if (ret)
+			return ret;
+
+		data->range[pwm] = adt7475_read(TEMP_TRANGE_REG(pwm));
+		data->range[pwm] &= ~0xf;
+		data->range[pwm] |= freq;
+
+		ret = i2c_smbus_write_byte_data(client, TEMP_TRANGE_REG(pwm), data->range[pwm]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
 static int adt7475_probe(struct i2c_client *client)
 {
 	enum chips chip;
@@ -1778,6 +1837,10 @@  static int adt7475_probe(struct i2c_client *client)
 	if (ret && ret != -EINVAL)
 		dev_warn(&client->dev, "Error configuring pwm polarity\n");
 
+	ret = adt7475_fan_pwm_config(client);
+	if (ret)
+		dev_warn(&client->dev, "Error %d configuring fan/pwm\n", ret);
+
 	/* Start monitoring */
 	switch (chip) {
 	case adt7475: