| Message ID | 20220719200626.976084-1-dmitry.baryshkov@linaro.org |
|---|---|
| Headers | show |
| Series | PCI: qcom: support using the same PHY for both RC and EP | expand |
On Tue, Jul 19, 2022 at 11:06:22PM +0300, Dmitry Baryshkov wrote: > Programming of QMP PCIe PHYs slightly differs between RC and EP modes. > > Currently both qcom and qcom-ep PCIe controllers setup the PHY in the > default mode, making it impossible to select at runtime whether the PHY > should be running in RC or in EP modes. Usually this is not an issue, > since for most devices only the RC mode is used, while for some (SDX55) > the EP mode is used without support for working as the RC. > SDX55 could work in RC mode also. Support is on the way. > Some of the Qualcomm platforms would still benefit from being able to > switch between RC and EP depending on the driver being used. While it is > possible to use different compat strings for the PHY depending on the > mode, it seems like an incorrect approach, since the PHY doesn't differ > between usecases. It's the PCIe controller, who should decide how to > configure the PHY. > > This patch series implements the ability to select between RC and EP > modes, by allowing the PCIe QMP PHY driver to switch between > programming tables. > This is really nice! On the case of SDX55, there is a single PHY and PCIe controller that is being used as both RC and EP depending on the usecase. While it makes sense to use a different PCIe node based on usecase, it does not for the PHY. So the runtime switch is a neat way of handling the differences. I've provided my review for the patches. But for the next iteration, you could remove the RFC tag. Also, please mention the dependency of the series in the cover letter if any. Like this one depends on your previous PHY cleanup series. It will help maintainers while picking the patches. Thanks a lot for the series! Regards, Mani > Dmitry Baryshkov (4): > phy: qcom-qmp-pcie: split register tables into primary and secondary > part > phy: qcom-qmp-pcie: suppor separate tables for EP mode > PCI: qcom: call phy_set_mode_ext() > PCI: qcom-ep: call phy_set_mode_ext() > > drivers/pci/controller/dwc/pcie-qcom-ep.c | 4 + > drivers/pci/controller/dwc/pcie-qcom.c | 4 + > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 155 ++++++++++++---------- > 3 files changed, 96 insertions(+), 67 deletions(-) > > -- > 2.35.1 >
On Thu, 21 Jul 2022 at 13:15, Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> wrote: > > On Tue, Jul 19, 2022 at 11:06:22PM +0300, Dmitry Baryshkov wrote: > > Programming of QMP PCIe PHYs slightly differs between RC and EP modes. > > > > Currently both qcom and qcom-ep PCIe controllers setup the PHY in the > > default mode, making it impossible to select at runtime whether the PHY > > should be running in RC or in EP modes. Usually this is not an issue, > > since for most devices only the RC mode is used, while for some (SDX55) > > the EP mode is used without support for working as the RC. > > > > SDX55 could work in RC mode also. Support is on the way. > > > Some of the Qualcomm platforms would still benefit from being able to > > switch between RC and EP depending on the driver being used. While it is > > possible to use different compat strings for the PHY depending on the > > mode, it seems like an incorrect approach, since the PHY doesn't differ > > between usecases. It's the PCIe controller, who should decide how to > > configure the PHY. > > > > This patch series implements the ability to select between RC and EP > > modes, by allowing the PCIe QMP PHY driver to switch between > > programming tables. > > > > This is really nice! On the case of SDX55, there is a single PHY and PCIe > controller that is being used as both RC and EP depending on the usecase. While > it makes sense to use a different PCIe node based on usecase, it does not for > the PHY. So the runtime switch is a neat way of handling the differences. > > I've provided my review for the patches. But for the next iteration, you could > remove the RFC tag. Thanks for the review! > Also, please mention the dependency of the series in the cover letter if any. > Like this one depends on your previous PHY cleanup series. It will help > maintainers while picking the patches. Ack. However the PHY series are already part of phy/next, thus I omitted mentioning them. > > Thanks a lot for the series! > > Regards, > Mani > > > Dmitry Baryshkov (4): > > phy: qcom-qmp-pcie: split register tables into primary and secondary > > part > > phy: qcom-qmp-pcie: suppor separate tables for EP mode > > PCI: qcom: call phy_set_mode_ext() > > PCI: qcom-ep: call phy_set_mode_ext() > > > > drivers/pci/controller/dwc/pcie-qcom-ep.c | 4 + > > drivers/pci/controller/dwc/pcie-qcom.c | 4 + > > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 155 ++++++++++++---------- > > 3 files changed, 96 insertions(+), 67 deletions(-) > > > > -- > > 2.35.1 > > > > -- > மணிவண்ணன் சதாசிவம்
Programming of QMP PCIe PHYs slightly differs between RC and EP modes. Currently both qcom and qcom-ep PCIe controllers setup the PHY in the default mode, making it impossible to select at runtime whether the PHY should be running in RC or in EP modes. Usually this is not an issue, since for most devices only the RC mode is used, while for some (SDX55) the EP mode is used without support for working as the RC. Some of the Qualcomm platforms would still benefit from being able to switch between RC and EP depending on the driver being used. While it is possible to use different compat strings for the PHY depending on the mode, it seems like an incorrect approach, since the PHY doesn't differ between usecases. It's the PCIe controller, who should decide how to configure the PHY. This patch series implements the ability to select between RC and EP modes, by allowing the PCIe QMP PHY driver to switch between programming tables. Dmitry Baryshkov (4): phy: qcom-qmp-pcie: split register tables into primary and secondary part phy: qcom-qmp-pcie: suppor separate tables for EP mode PCI: qcom: call phy_set_mode_ext() PCI: qcom-ep: call phy_set_mode_ext() drivers/pci/controller/dwc/pcie-qcom-ep.c | 4 + drivers/pci/controller/dwc/pcie-qcom.c | 4 + drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 155 ++++++++++++---------- 3 files changed, 96 insertions(+), 67 deletions(-)